Atheros 3011 has small sflash firmware and needs to be
blacklisted in transport driver to load actual firmware
in DFU driver.
Signed-off-by: Bala Shanmugam <sbalashanmugam@atheros.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>

If a device is autosuspended an inability to resubmit URBs is
to be expected. Check the error code and only log real errors.
(Now that autosuspend is default enabled for btusb, those log
messages were happening all the time e.g. with a BT mouse)
Signed-off-by: Stefan Seyfried <seife+kernel@b1-systems.com>
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>

Return 0 in that situation could lead to errors in the caller.
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>

In order to use build-in debugging macro, pci_dev in priv need to be
assigned first.

This fix iwl3945 driver oopsed at boot with 2.6.37-rc1
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Adding the new MacBookAir3,1(2) to btusb.

Output without the patch and btusb loaded :

T:  Bus=03 Lev=02 Prnt=03 Port=02 Cnt=01 Dev#=  6 Spd=12  MxCh= 0
D:  Ver= 2.00 Cls=ff(vend.) Sub=01 Prot=01 MxPS=64 #Cfgs=  1
P:  Vendor=05ac ProdID=821b Rev= 0.34
S:  Manufacturer=Apple Inc.
S:  Product=Bluetooth USB Host Controller
C:* #Ifs= 4 Cfg#= 1 Atr=e0 MxPwr=  0mA
I:* If#= 0 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=01 Prot=01 Driver=(none)
E:  Ad=81(I) Atr=03(Int.) MxPS=  16 Ivl=1ms
E:  Ad=82(I) Atr=02(Bulk) MxPS=  64 Ivl=0ms
E:  Ad=02(O) Atr=02(Bulk) MxPS=  64 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=(none)
E:  Ad=83(I) Atr=01(Isoc) MxPS=   0 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=   0 Ivl=1ms
I:  If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=(none)
E:  Ad=83(I) Atr=01(Isoc) MxPS=   9 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=   9 Ivl=1ms
I:  If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=(none)
E:  Ad=83(I) Atr=01(Isoc) MxPS=  17 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  17 Ivl=1ms
I:  If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=(none)
E:  Ad=83(I) Atr=01(Isoc) MxPS=  32 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  32 Ivl=1ms
I:  If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=(none)
E:  Ad=83(I) Atr=01(Isoc) MxPS=  64 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  64 Ivl=1ms
I:  If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=(none)
E:  Ad=83(I) Atr=01(Isoc) MxPS=  64 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  64 Ivl=1ms
I:* If#= 2 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)
E:  Ad=84(I) Atr=02(Bulk) MxPS=  32 Ivl=0ms
E:  Ad=04(O) Atr=02(Bulk) MxPS=  32 Ivl=0ms
I:* If#= 3 Alt= 0 #EPs= 0 Cls=fe(app. ) Sub=01 Prot=01 Driver=(none)

Output with the patch and btusb loaded :

T:  Bus=03 Lev=02 Prnt=03 Port=02 Cnt=01 Dev#=  6 Spd=12  MxCh= 0
D:  Ver= 2.00 Cls=ff(vend.) Sub=01 Prot=01 MxPS=64 #Cfgs=  1
P:  Vendor=05ac ProdID=821b Rev= 0.34
S:  Manufacturer=Apple Inc.
S:  Product=Bluetooth USB Host Controller
C:* #Ifs= 4 Cfg#= 1 Atr=e0 MxPwr=  0mA
I:* If#= 0 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=01 Prot=01 Driver=btusb
E:  Ad=81(I) Atr=03(Int.) MxPS=  16 Ivl=1ms
E:  Ad=82(I) Atr=02(Bulk) MxPS=  64 Ivl=0ms
E:  Ad=02(O) Atr=02(Bulk) MxPS=  64 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=   0 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=   0 Ivl=1ms
I:  If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=   9 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=   9 Ivl=1ms
I:  If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  17 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  17 Ivl=1ms
I:  If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  32 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  32 Ivl=1ms
I:  If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  64 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  64 Ivl=1ms
I:  If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  64 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  64 Ivl=1ms
I:* If#= 2 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)
E:  Ad=84(I) Atr=02(Bulk) MxPS=  32 Ivl=0ms
E:  Ad=04(O) Atr=02(Bulk) MxPS=  32 Ivl=0ms
I:* If#= 3 Alt= 0 #EPs= 0 Cls=fe(app. ) Sub=01 Prot=01 Driver=(none)
Signed-off-by: Edgar (gimli) Hucek <gimli@dark-green.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>

This cause 'No Bonding' to be used if userspace has not yet been paired
with remote device since the l2cap socket used to create the rfcomm
session does not have any security level set.
Signed-off-by: Luiz Augusto von Dentz <luiz.dentz-von@nokia.com>
Acked-by: Ville Tervo <ville.tervo@nokia.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>

Last commit added a wrong endianness conversion. Fixing that.
Reported-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>

In function l2cap_get_conf_opt() and l2cap_add_conf_opt() the address of
opt->val sometimes is not at the edge of 2-bytes/4-bytes, so 2-bytes/4 bytes
access will cause data misalignment exeception.  Use get_unaligned_le16/32
and put_unaligned_le16/32 function to avoid data misalignment execption.
Signed-off-by: steven miao <realmz6@gmail.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>

We've done this for a while in Fedora without any obvious problems other
than some interaction with input devices. Those should be fixed now, so
let's try this in mainline.
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>

When initiating dedicated bonding a L2CAP raw socket with HIGH security
level is used. The kernel is supposed to trigger the authentication
request in this case but this doesn't happen currently for non-SSP
(pre-2.1) devices. The reason is that the authentication request happens
in the remote extended features callback which never gets called for
non-SSP devices. This patch fixes the issue by requesting also
authentiation in the (normal) remote features callback in the case of
non-SSP devices.

This rule is applied only for HIGH security level which might at first
seem unintuitive since on the server socket side MEDIUM is already
enough for authentication. However, for the clients we really want to
prefer the server side to decide the authentication requrement in most
cases, and since most client sockets use MEDIUM it's better to be
avoided on the kernel side for these sockets. The important socket to
request it for is the dedicated bonding one and that socket uses HIGH
security level.

The patch is based on the initial investigation and patch proposal from
Andrei Emeltchenko <endrei.emeltchenko@nokia.com>.
Signed-off-by: Johan Hedberg <johan.hedberg@nokia.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>

Fix kconfig dependency warning to satisfy dependencies:

warning: (BT_HIDP && NET && BT && BT_L2CAP && INPUT || USB_HID && HID_SUPPORT && USB && INPUT) selects HID which has unmet direct dependencies (HID_SUPPORT && INPUT)
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>

The allocated externel radio banks have to be freed in
case of ath9k_hw_rf_alloc_ext_banks failure.

Cc: stable@kernel.org
Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Since the endpoint descriptors (EP3 & EP4) were changed from Interrupt
to Bulk type by firmware, the urb submission done on Bulk pipes.
And the recent commit "check the endpoint type against the pipe type"
added aditional error checking against pipe types under CONFIG_USB_DEBUG.

So bmAttribute has to be updated for both EP3 & EP4 before submitting
urbs on that pipe. This patch resolves the following failure.

[ 2215.710936] usb 1-1: usb_probe_device
[ 2215.710945] usb 1-1: configuration #1 chosen from 1 choice
[ 2215.711152] usb 1-1: adding 1-1:1.0 (config #1, interface 0)
[ 2215.711252] ath9k_hif_usb 1-1:1.0: usb_probe_interface
[ 2215.711255] ath9k_hif_usb 1-1:1.0: usb_probe_interface - got id
[ 2215.712780] usb 1-1: BOGUS urb xfer, pipe 3 != type 1
[ 2215.713782] usb 1-1: ath9k_htc: Unable to allocate URBs
[ 2215.713801] ath9k_hif_usb: probe of 1-1:1.0 failed with error -22
Reported-by: Ming Lei <tom.leiming@gmail.com>
Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This patch adds support for USB dongle with device ID 3346 from IMC Networks.
Signed-off-by: Haitao Zhang <minipanda@linuxrobot.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Bit 22 of AR_WA should be set to fix the situation where chip reset
is asynchronous to clock of analog shift registers, such that when
reset is released, it could mess up the values of analog shift registers
and cause some hw issue on AR9280.

This bit is write only, but the driver does a read-modify-write
on AR_WA without setting bit 22 in ar9002_hw_configpcipowersave()
during radio disable. This causes surprise removal of hw. It can
never recover from this state and the hw will become usable only
after a power on/off cycle, and sometimes only during a cold reboot.

This issue can be triggered by doing frequent roaming with the
simple/test-roam script available from the wifi-test project [1]
when roaming between APs quickly. When roaming there is a is a high
possibility that the device being put into idle (radio disable) state
by mac80211 during AUTH->ASSOC. A device hardware reset would fail
and the kernel would output:

[40251.363799] ath: AWAKE -> FULL-SLEEP
[40251.363815] ieee80211 phy17: device no longer idle - working
[40251.363817] ath: Marking phy17 as not-idle
[40251.363819] ath: FULL-SLEEP -> AWAKE
[40251.415978] pciehp 0000:00:1c.3:pcie04: Card not present on Slot(3)
[40251.419896] ath: ah->misc_mode 0x4
[40251.428138] pciehp 0000:00:1c.3:pcie04: Card present on Slot(3)
[40251.532247] ath: timeout (100000 us) on reg 0x9860: 0xffffffff & 0x00000001 != 0x00000000
[40251.532250] ath: Unable to reset channel (2462 MHz), reset status -5
[40251.532422] ath: Set channel: 5745 MHz
[40251.540639] ath: Failed to stop TX DMA in 100 msec after killing last frame
[40251.548826] ath: Failed to stop TX DMA in 100 msec after killing last frame
[40251.557023] ath: Failed to stop TX DMA in 100 msec after killing last frame
[40251.565211] ath: Failed to stop TX DMA in 100 msec after killing last frame
[40251.573415] ath: Failed to stop TX DMA in 100 msec after killing last frame
[40251.581603] ath: Failed to stop TX DMA in 100 msec after killing last frame
[40251.581606] ath: Failed to stop TX DMA. Resetting hardware!
[40251.592679] ath: DMA failed to stop in 10 ms AR_CR=0xffffffff AR_DIAG_SW=0xffffffff
[40251.703330] ath: timeout (100000 us) on reg 0x7000: 0xffffffff & 0x00000003 != 0x00000000
[40251.703333] ath: RTC stuck in MAC reset
[40251.703334] ath: Chip reset failed
[40251.703335] ath: Unable to reset hardware; reset status -22

This is currently only reproducible with some HB92 (Half Mini-PCIE)
cards but the fix applies to all AR9280 cards. This patch fixes this
issue by setting bit 22 during radio disable.

This patch has fixes for all kernels that has ath9k.

[1] http://wireless.kernel.org/en/developers/Testing/wifi-test

Cc: kyungwan.nam@atheros.com
Cc: amod.bodas@atheros.com
Cc: david.quan@atheros.com
Cc: stable@kernel.org
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

There are currently no provisions in place to ensure that the scanning
task has been stopped when the interface is stopped or removed.

This can result in a WARNING at net/wireless/core.c:643 and other badness
when you remove the module while a scan is happening.

Terminate the scanning task during interface stop.
Signed-off-by: Daniel Drake <dsd@laptop.org>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

For client STA interfaces, ieee80211_do_stop unsets the relevant
interface's SDATA_STATE_RUNNING state bit prior to cancelling an
interrupted scan.  When ieee80211_offchannel_return is invoked as
part of cancelling the scan, it doesn't bother unsetting the
SDATA_STATE_OFFCHANNEL bit because it sees that the interface is
down.  Normally this doesn't matter because when the client STA
interface is brought back up, it will probably issue a scan.  But
in some cases (e.g., the user changes the interface type while it
is down), the SDATA_STATE_OFFCHANNEL bit will remain set.  This
prevents the interface queues from being started.  So we
cancel the scan before unsetting the SDATA_STATE_RUNNING bit.
Signed-off-by: Brian Cavagnolo <brian@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k_ps_wakeup() clears the cycle counters after waking up the
hardware using ath9k_hw_setpower, however if power save is disabled,
then the counters will contain useful data, which then gets discarded.
Fix this by checking the old power mode before discarding any data.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

IS_ERR and PTR_ERR were called with the wrong pointer, leading to a
crash when cfg80211_get_dev_from_ifindex fails.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This patch includes the following updates:
 * add D-Link DWA-130 Rev D
 * Netgear has three WNDA3100 versions.
   the original WNDA3100 is now called WNDA3100v1.
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Throughput was severely affected in Intel Pinetrail platforms
because of a DMA problem in C3 state. This patch fixes this
issue.
Signed-off-by: Vivek Natarajan <vnatarajan@atheros.com>
CC: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

The HW opmode is blindly set to monitor type on monitor mode
change notification. This overrides the opmode when one of the
interfaces is still running as non-monitor iftype. So the monitoring
information needs to be maintained seperately.
Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This bug seems to be due to commit 27ae60f8 ("ipw2x00: replace
"ieee80211" with "libipw" where appropriate"), where Pavel did this:

-       libipw_proc = proc_mkdir(DRV_NAME, init_net.proc_net);
+       libipw_proc = proc_mkdir("ieee80211", init_net.proc_net);

but then the cleanup was kept as

        remove_proc_entry(DRV_NAME, init_net.proc_net);

in both places (both in the failure case and in the unload case). The
error string is also total crap, and says

     "Unable to create " DRV_NAME " proc directory\n");

Even though it doesn't actually create a proc directory named DRV_NAME at all.

So that patch looks like total and utter crap to me. The commit message says

  "Keep /proc/net/ieee80211 under the original name to avoid breaking user
    interface."

but the thing is, it really didn't fix anything but that one create
thing. It needs to fix all the other cases too.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Tested-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

On module removal, the sdio version of b43 generates the following warning:

[  851.560519] ------------[ cut here ]------------
[  851.560531] WARNING: at drivers/mmc/core/core.c:237 mmc_wait_for_cmd+0x88/0x90()
[  851.560534] Hardware name: 20552PG
[  851.560536] Modules linked in: b43(-) ssb mmc_block binfmt_misc rfcomm sco bnep ppdev l2cap ipt_MASQUERADE iptable_nat nf_nat nf_conntrack_ipv4 nf_defrag_ipv4 xt_state nf_conntrack ipt_REJECT xt_tcpudp iptable_filter ip_tables x_tables bridge stp kvm_intel kvm arc4 iwlagn snd_hda_codec_conexant snd_hda_intel snd_hda_codec iwlcore snd_hwdep snd_pcm thinkpad_acpi mac80211 snd_seq_midi snd_rawmidi snd_seq_midi_event snd_seq r852 joydev snd_timer sm_common pcmcia nand snd_seq_device cfg80211 sdhci_pci btusb psmouse tpm_tis yenta_socket nand_ids lp snd pcmcia_rsrc nand_ecc bluetooth sdhci tpm pcmcia_core parport mtd snd_page_alloc serio_raw tpm_bios soundcore nvram led_class sha256_generic aes_i586 aes_generic dm_crypt i915 drm_kms_helper drm ahci intel_agp i2c_algo_bit intel_gtt e1000e libahci video agpgart output
[  851.560620] Pid: 2504, comm: rmmod Not tainted 2.6.36-titan0+ #1
[  851.560622] Call Trace:
[  851.560631]  [<c014a102>] warn_slowpath_common+0x72/0xa0
[  851.560636]  [<c04d94c8>] ? mmc_wait_for_cmd+0x88/0x90
[  851.560641]  [<c04d94c8>] ? mmc_wait_for_cmd+0x88/0x90
[  851.560645]  [<c014a152>] warn_slowpath_null+0x22/0x30
[  851.560649]  [<c04d94c8>] mmc_wait_for_cmd+0x88/0x90
[  851.560655]  [<c0401585>] ? device_release+0x25/0x80
[  851.560660]  [<c04df210>] mmc_io_rw_direct_host+0xa0/0x150
[  851.560665]  [<c04df370>] mmc_io_rw_direct+0x30/0x40
[  851.560669]  [<c04e06e7>] sdio_disable_func+0x37/0xa0
[  851.560683]  [<f8dfcb80>] b43_sdio_remove+0x30/0x50 [b43]
[  851.560687]  [<c04df8cc>] sdio_bus_remove+0x1c/0x60
[  851.560692]  [<c016d39f>] ? blocking_notifier_call_chain+0x1f/0x30
[  851.560697]  [<c0404991>] __device_release_driver+0x51/0xb0
[  851.560701]  [<c0404a7f>] driver_detach+0x8f/0xa0
[  851.560705]  [<c0403c83>] bus_remove_driver+0x63/0xa0
[  851.560709]  [<c0405039>] driver_unregister+0x49/0x80
[  851.560713]  [<c0405039>] ? driver_unregister+0x49/0x80
[  851.560718]  [<c04dfad7>] sdio_unregister_driver+0x17/0x20
[  851.560727]  [<f8dfcb42>] b43_sdio_exit+0x12/0x20 [b43]
[  851.560734]  [<f8dfe76f>] b43_exit+0x17/0x3c [b43]
[  851.560740]  [<c017fb8d>] sys_delete_module+0x13d/0x200
[  851.560747]  [<c01fd7d2>] ? do_munmap+0x212/0x300
[  851.560752]  [<c010311f>] sysenter_do_call+0x12/0x28
[  851.560757] ---[ end trace 31e14488072d2f7d ]---
[  851.560759] ------------[ cut here ]------------

The warning is caused by b43 not claiming the device before calling
sdio_disable_func().
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Reported-by: Arnd Hannemann <arnd@arndnet.de>
Tested-by: Arnd Hannemann <arnd@arndnet.de>
Cc: Stable <stable@kernel.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

I noticed two small issues in mac80211/debugfs_key.c::key_key_read while
reading through the code. Patch below.

The key_key_read() function returns ssize_t and the value that's actually
returned is the return value of simple_read_from_buffer() which also
returns ssize_t, so let's hold the return value in a ssize_t local
variable rather than a int one.

Also, memory is allocated dynamically with kmalloc() which can fail, but
the return value of kmalloc() is not checked, so we may end up operating
on a null pointer further on. So check for a NULL return and bail out with
-ENOMEM in that case.
Signed-off-by: Jesper Juhl <jj@chaosbits.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

For the SD8686, we cannot rely on the scratch register to read the firmware
load status, because the same register is used for storing RX packet length.
Broaden the check to account for this.

The module can now be unloaded/reloaded successfully.

Based on the implementation from libertas_tf.
Signed-off-by: Daniel Drake <dsd@laptop.org>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: Steve deRosier <steve@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

The index variable to access the rate flags should be obtained from the
inner loop counter which corresponds to the rate table structure.This
fixes the invalid rate selection i.e when the supported basic rate is
invalid on a particular band and also the following warning message.
Thanks to Raj for finding this out.

Call Trace:

 [<ffffffff8104ee4a>] warn_slowpath_common+0x7a/0xb0

 [<ffffffff8104ee95>] warn_slowpath_null+0x15/0x20

 [<ffffffffa0583c45>] ath_get_rate+0x595/0x5b0 [ath9k]

 [<ffffffff811a0636>] ? cpumask_next_and+0x36/0x50

 [<ffffffffa0405186>] rate_control_get_rate+0x86/0x160 [mac80211]

 [<ffffffffa040dfac>] invoke_tx_handlers+0x81c/0x12d0 [mac80211]

 [<ffffffffa040eae9>] ieee80211_tx+0x89/0x2b0 [mac80211]

 [<ffffffff812891bc>] ? pskb_expand_head+0x1cc/0x1f0

 [<ffffffffa040edc5>] ieee80211_xmit+0xb5/0x1c0 [mac80211]

 [<ffffffffa041026f>] ieee80211_tx_skb+0x4f/0x60 [mac80211]

 [<ffffffffa03fe016>] ieee80211_send_nullfunc+0x46/0x60 [mac80211]

 [<ffffffffa03f91d7>] ieee80211_offchannel_stop_station+0x107/0x150
[mac80211]

 [<ffffffff812891bc>] ? pskb_expand_head+0x1cc/0x1f0

 [<ffffffffa040edc5>] ieee80211_xmit+0xb5/0x1c0 [mac80211]

 [<ffffffffa041026f>] ieee80211_tx_skb+0x4f/0x60 [mac80211]

 [<ffffffffa03fe016>] ieee80211_send_nullfunc+0x46/0x60 [mac80211]

 [<ffffffffa03f91d7>] ieee80211_offchannel_stop_station+0x107/0x150
[mac80211]

 [<ffffffffa03f8896>] ieee80211_scan_work+0x146/0x600 [mac80211]

 [<ffffffff8133a375>] ? schedule+0x2f5/0x8e0

 [<ffffffffa03f8750>] ? ieee80211_scan_work+0x0/0x600 [mac80211]

 [<ffffffff81064fcf>] process_one_work+0x10f/0x380

 [<ffffffff81066bc2>] worker_thread+0x162/0x340

 [<ffffffff81066a60>] ? worker_thread+0x0/0x340

Cc: stable@kernel.org
Signed-off-by: Mohammed Shafi Shajakhan <mshajakhan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

If ath5k_hw_attach fails it will free sc->ah (local variable ah) before
returning. However, when it reports failure the caller (ath5k_pci_probe)
will also free sc->ah. Let the caller handle the deallocation, it does
so on further errors as well.
Signed-off-by: Jones Desougi <jones.desougi@27m.se>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Commit 651b5225 added DS Parameter Set
information into Probe Request frames that are transmitted on 2.4 GHz
band, but it failed to increment local->scan_ies_len to cover this new
information. This variable needs to be updated to match the maximum IE
data length so that the extra buffer need gets reduced from the driver
limit.
Signed-off-by: Jouni Malinen <j@w1.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Netgear WNDA3200 device uses ar7010 firmware but it is failed to set
correct firmware offset on firmware download which causes device initialization
failure.

Cc: stable@kernel.org
Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Completing aggregate frames can lead to new buffers being pushed into
the tid queues due to software retransmission.
When the tx queues are being drained, all pending aggregates must be
completed before the tid queues get drained, otherwise buffers might be
leaked.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Cc: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Apart from locking the start and stop PCU we need
to ensure we also content starting and stopping the PCU
between hardware resets.

This is part of a series that will help resolve the bug:

https://bugzilla.kernel.org/show_bug.cgi?id=14624

For more details about this issue refer to:

http://marc.info/?l=linux-wireless&m=128629803703756&w=2

Cc: stable@kernel.org
Cc: Ben Greear <greearb@candelatech.com>
Cc: Kyungwan Nam <kyungwan.nam@atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Tested-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

The real way to lock RX is to contend on the PCU
and reset, this will be fixed in the next patch but for
now just do the renames so that the next patch which changes
the locking order is crystal clear.

This is part of a series that will help resolve the bug:

https://bugzilla.kernel.org/show_bug.cgi?id=14624

For more details about this issue refer to:

http://marc.info/?l=linux-wireless&m=128629803703756&w=2

Cc: stable@kernel.org
Cc: Ben Greear <greearb@candelatech.com>
Cc: Kyungwan Nam <kyungwan.nam@atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Tested-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

There was some locking for starting some parts of
RX but not for starting the PCU. Include this otherwise
we can content against stopping the PCU.

This can potentially lead to races against different
buffers on the PCU which can lead to to the DMA RX
engine writing to buffers which are already freed.

This is part of a series that will help resolve the bug:

https://bugzilla.kernel.org/show_bug.cgi?id=14624

For more details about this issue refer to:

http://marc.info/?l=linux-wireless&m=128629803703756&w=2

Cc: stable@kernel.org
Cc: Ben Greear <greearb@candelatech.com>
Cc: Kyungwan Nam <kyungwan.nam@atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Tested-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k locks for starting RX but not for stopping RX. We could
potentially run into a situation where tried to stop RX
but immediately started RX. This allows for races on the
the RX engine deciding what buffer we last left off on
and could potentially cause ath9k to DMA into already
free'd memory or in the worst case at a later time to
already given memory to other drivers.

Fix this by locking stopping RX.

This is part of a series that will help resolve the bug:

https://bugzilla.kernel.org/show_bug.cgi?id=14624

For more details about this issue refer to:

http://marc.info/?l=linux-wireless&m=128629803703756&w=2

Cc: stable@kernel.org
Cc: Ben Greear <greearb@candelatech.com>
Cc: Kyungwan Nam <kyungwan.nam@atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Tested-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Timing issues in microcode for some devices can cause a compressed BA to
be sent to the driver prior to returning any a-MPDU notification.
Traces show RTS-CTS is exchanged and then the timer fires which causes an
empty BA to be sent which acknowledges nothing.  This results in a noisy
printk. Only print the message if the bitmap is non-zero.
Signed-off-by: Don Fry <donald.h.fry@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Since aggregation is usually triggered by tx completion, a hardware
reset (because of beacon stuck, tx hang or baseband hang) can
significantly delay the transmission of the next AMPDU (until the next
tx completion event).
Fix this by rescheduling aggregation after such a reset.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Cc: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This patch fixes the following mishap:

BUG: scheduling while atomic: wpa_supplicant/4164/0x00000002
Modules linked in: carl9170 mac80211 [...]
Pid: 4164, comm: wpa_supplicant Not tainted 2.6.36-wl+ #119
Call Trace:
 [<c13779a9>] ? schedule+0x349/0x4c0
 [<c13780d6>] ? schedule_timeout+0x106/0x1e0
 [<c1037f50>] ? process_timeout+0x0/0x10
 [<c1377e8d>] ? wait_for_common+0x9d/0x140
 [<c1029110>] ? default_wake_function+0x0/0x10
 [<f80c6080>] ? carl9170_exec_cmd+0xf0/0x250 [carl9170]
 [<f80c695e>] ? carl9170_set_mac_reg+0x5e/0x70 [carl9170]
 [<f80c3f76>] ? carl9170_op_add_interface+0x176/0x310 [carl9170]
 [...]

rcu_read_unlock() call was erroneously placed after the
sync. function carl9170_mod_virtual_mac.
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Station addition in ieee80211_ibss_rx_queued_mgmt is not updating
sta->last_rx which is causing station expiry in ieee80211_ibss_work
path. So sta addition and deletion happens repeatedly.

CC: stable@kernel.org
Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>