- 14 Feb, 2011 11 commits
-
-
Guo-Fu Tseng authored
Some JMicron Chip treat 0 as error checksum for UDP packets. Which should be "No checksum needed". Reported-by: Adam Swift <Adam.Swift@omnitude.net> Confirmed-by: "Aries Lee" <arieslee@jmicron.com> Signed-off-by: Guo-Fu Tseng <cooldavid@cooldavid.org> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Guo-Fu Tseng authored
The value of the register which holds receive Unicast MAC Address sometimes get messed-up after resume. This patch refill it before enabling the hardware filter. Signed-off-by: Guo-Fu Tseng <cooldavid@cooldavid.org> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Guo-Fu Tseng authored
Adding control to clk_rx, and makes the control of clk_{rx|tx|tcp} with safer sequence. This sequence is provided by JMicron. Signed-off-by: Guo-Fu Tseng <cooldavid@cooldavid.org> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Guo-Fu Tseng authored
Clear Transmit Timer/Retry setting while full-duplex. Signed-off-by: Guo-Fu Tseng <cooldavid@cooldavid.org> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Guo-Fu Tseng authored
Signed-off-by: Guo-Fu Tseng <cooldavid@cooldavid.org> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Guo-Fu Tseng authored
Signed-off-by: Guo-Fu Tseng <cooldavid@cooldavid.org> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Guo-Fu Tseng authored
After main chip rev 5, the hardware support more power saving control registers. Some Non-Linux drivers might turn off the phy power with new interfaces, this patch makes it possible for Linux to turn it on again. Signed-off-by: Guo-Fu Tseng <cooldavid@cooldavid.org> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Guo-Fu Tseng authored
Get the main and sub chip revision for later workaround use. Signed-off-by: Guo-Fu Tseng <cooldavid@cooldavid.org> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Jiri Pirko authored
add possibility to addif/delif via rtnetlink Signed-off-by: Jiri Pirko <jpirko@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Jiri Pirko authored
allow enslaving/releasing using netlink interface Signed-off-by: Jiri Pirko <jpirko@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Jiri Pirko authored
This patch allows userspace to enslave/release slave devices via netlink interface using IFLA_MASTER. This introduces generic way to add/remove underling devices. Signed-off-by: Jiri Pirko <jpirko@redhat.com> Acked-by: Patrick McHardy <kaber@trash.net> Signed-off-by: David S. Miller <davem@davemloft.net>
-
- 13 Feb, 2011 3 commits
-
-
Sakari Ailus authored
Fix two bugs introduced by the commit c659c38b ("tlan: Code cleanup: checkpatch.pl is relatively happy now.") In that change, TLAN_CSTAT_READY was considered as a bit mask containing a single bit set while it was actually had two set instead. Many thanks to Dan Carpenter for finding the mistake. Signed-off-by: Sakari Ailus <sakari.ailus@iki.fi> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Jiri Pirko authored
dev->master is now tightly connected to bonding driver. This patch makes this pointer more general and ready to be used by others. - netdev_set_master() - bond specifics moved to new function netdev_set_bond_master() - introduced netif_is_bond_slave() to check if device is a bonding slave Signed-off-by: Jiri Pirko <jpirko@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Jiri Pirko authored
No need to check (master) twice and to drive in and out the header file. Signed-off-by: Jiri Pirko <jpirko@redhat.com> Reviewed-by: Nicolas de Pesloüan <nicolas.2p.debian@free.fr> Signed-off-by: David S. Miller <davem@davemloft.net>
-
- 12 Feb, 2011 19 commits
-
-
hartleys authored
Remove unneeded depends on PHYLIB. The config selection is already in an if PHYLIB / endif block. Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com> Cc: "David S. Miller" <davem@davemloft.net> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Ben Greear authored
This allows user-space to send a '1500' MTU VLAN packet on a 1500 MTU ethernet frame. The extra 4 bytes of a VLAN header is not usually charged against the MTU when other parts of the network stack is transmitting vlans... Signed-off-by: Ben Greear <greearb@candelatech.com> Reviewed-by: Eric Dumazet <eric.dumazet@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
-
Ajit Khaparde authored
WOL is not supported for Vrtual Functions. Signed-off-by: Ajit Khaparde <ajit.khaparde@emulex.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Ajit Khaparde authored
Signed-off-by: Ajit Khaparde <ajit.khaparde@emulex.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Ajit Khaparde authored
Avoid accessing the hardware when UE is detected. Signed-off-by: Ajit Khaparde <ajit.khaparde@emulex.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Ajit Khaparde authored
> call pci msix disable in be_suspend > call pci msix enable in be_resume > stop worker thread in be_suspend > start worker thread in be_resume > stop worker thread in be_shutdown Signed-off-by: Ajit Khaparde <ajit.khaparde@emulex.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Ajit Khaparde authored
Signed-off-by: Ajit Khaparde <ajit.khaparde@emulex.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Ajit Khaparde authored
Signed-off-by: Ajit Khaparde <ajit.khaparde@emulex.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Ajit Khaparde authored
Signed-off-by: Ajit Khaparde <ajit.khaparde@emulex.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Ajit Khaparde authored
be_cmd_pmac_add/del functions need to pass domain number to the firmware. Signed-off-by: Ajit Khaparde <ajit.khaparde@emulex.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Ajit Khaparde authored
Currently we are always using the Emulex OUI for a VF MAC address while generating MAC for a VF. Use OUI from current MAC instead. Signed-off-by: Ajit Khaparde <ajit.khaparde@emulex.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Ajit Khaparde authored
The PF needs to cleanup all the interface handles that it created for the VFs. Signed-off-by: Ajit Khaparde <ajit.khaparde@emulex.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Ajit Khaparde authored
This is to avoid the completion processing for be_vf_eth_addr_config to consume the link status notification before netdev_register. Otherwise this causes the PF miss its first link status update. Signed-off-by: Ajit Khaparde <ajit.khaparde@emulex.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Ajit Khaparde authored
Signed-off-by: Ajit Khaparde <ajit.khaparde@emulex.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Ajit Khaparde authored
Signed-off-by: Ajit Khaparde <ajit.khaparde@emulex.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Ajit Khaparde authored
Signed-off-by: Ajit Khaparde <ajit.khaparde@emulex.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Ajit Khaparde authored
While configuring QOS for VFs, the VF number should be translated to domain number correctly. Signed-off-by: Ajit Khaparde <ajit.khaparde@emulex.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
David S. Miller authored
-
- 11 Feb, 2011 7 commits
-
-
Linus Lüssing authored
For a host in the mesh network, the batman layer should be transparent. However, we had one exception, data packets within the mesh network which have the same destination as a originator are being routed to that node, although there is no host that node's bat0 interface and therefore gets dropped anyway. This commit removes this exception. Signed-off-by: Linus Lüssing <linus.luessing@ascom.ch> Signed-off-by: Sven Eckelmann <sven@narfation.org>
-
Linus Lüssing authored
types.h is included by main.h, which is included at the beginning of any other c-file anyway. Therefore this commit removes those duplicate inclussions. Signed-off-by: Linus Lüssing <linus.luessing@ascom.ch> Signed-off-by: Sven Eckelmann <sven@narfation.org>
-
Marek Lindner authored
Multiple variable declarations in a single statements over multiple lines can be split into multiple variable declarations without changing the actual behavior. Signed-off-by: Marek Lindner <lindner_marek@yahoo.de> Signed-off-by: Sven Eckelmann <sven@narfation.org>
-
Rafael J. Wysocki authored
The atl1 driver uses the legacy PCI power management, so it has to do some PCI-specific things in its ->suspend() and ->resume() callbacks, which isn't necessary and should better be done by the PCI subsystem-level power management code. Convert atl1 to the new PCI power management framework and make it let the PCI subsystem take care of all the PCI-specific aspects of device handling during system power transitions. Tested-by: Thomas Fjellstrom <thomas@fjellstrom.ca> Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Rafael J. Wysocki authored
The atl1c driver shouldn't call device_init_wakeup() in its probe routine with the second argument equal to 1, because for PCI devices the wakeup capability setting is initialized as appropriate by the PCI subsystem. Remove the potentially harmful call. Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Rafael J. Wysocki authored
The tg3 driver uses device_init_wakeup() in such a way that the device's power.can_wakeup flag may be set even though the PCI subsystem cleared it before, in which case the device cannot wake up the system from sleep states. Modify the driver to only change the power.can_wakeup flag if the device is not capable of generating wakeup signals. Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl> Acked-by: Matt Carlson <mcarlson@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Atita Shirwaikar authored
Current driver does not show 100MB support in ethtool. Adding support for the same. Signed-off-by: Atita Shirwaikar <atita.shirwaikar@intel.com> Tested-by: Stephen Ko <stephen.s.ko@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
-