- 03 Jan, 2020 4 commits
-
-
Andrew Lunn authored
In order to dump the FECs registers the clocks have to be ticking, otherwise a data abort occurs. Add calls to runtime PM so they are enabled and later disabled. Fixes: e8fcfcd5 ("net: fec: optimize the clock management to save power") Reported-by: Chris Healy <Chris.Healy@zii.aero> Signed-off-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Hangbin Liu authored
Before ip_tunnel_ecn_encap() and udp_tunnel_xmit_skb() we should filter tos value by RT_TOS() instead of using config tos directly. vxlan_get_route() would filter the tos to fl4.flowi4_tos but we didn't return it back, as geneve_get_v4_rt() did. So we have to use RT_TOS() directly in function ip_tunnel_ecn_encap(). Fixes: 206aaafc ("VXLAN: Use IP Tunnels tunnel ENC encap API") Fixes: 1400615d ("vxlan: allow setting ipv6 traffic class") Signed-off-by: Hangbin Liu <liuhangbin@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Wen Yang authored
The variables 'window_interval' is u64 and do_div() truncates it to 32 bits, which means it can test non-zero and be truncated to zero for division. The unit of window_interval is nanoseconds, so its lower 32-bit is relatively easy to exceed. Fix this issue by using div64_u64() instead. Fixes: 7298de9c ("sch_cake: Add ingress mode") Signed-off-by: Wen Yang <wenyang@linux.alibaba.com> Cc: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk> Cc: Toke Høiland-Jørgensen <toke@redhat.com> Cc: David S. Miller <davem@davemloft.net> Cc: Cong Wang <xiyou.wangcong@gmail.com> Cc: cake@lists.bufferbloat.net Cc: netdev@vger.kernel.org Cc: linux-kernel@vger.kernel.org Acked-by: Toke Høiland-Jørgensen <toke@toke.dk> Signed-off-by: David S. Miller <davem@davemloft.net>
-
David S. Miller authored
It can take on the values of '0', '1', and '2' and thus is not a boolean. Signed-off-by: David S. Miller <davem@davemloft.net>
-
- 02 Jan, 2020 2 commits
-
-
Pengcheng Yang authored
When we receive a D-SACK, where the sequence number satisfies: undo_marker <= start_seq < end_seq <= prior_snd_una we consider this is a valid D-SACK and tcp_is_sackblock_valid() returns true, then this D-SACK is discarded as "old stuff", but the variable first_sack_index is not marked as negative in tcp_sacktag_write_queue(). If this D-SACK also carries a SACK that needs to be processed (for example, the previous SACK segment was lost), this SACK will be treated as a D-SACK in the following processing of tcp_sacktag_write_queue(), which will eventually lead to incorrect updates of undo_retrans and reordering. Fixes: fd6dad61 ("[TCP]: Earlier SACK block verification & simplify access to them") Signed-off-by: Pengcheng Yang <yangpc@wangsu.com> Signed-off-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Baruch Siach authored
mv88e6xxx_port_set_cmode() relies on cmode stored in struct mv88e6xxx_port to skip cmode update when the requested value matches the cached value. It turns out that mv88e6xxx_port_hidden_write() might change the port cmode setting as a side effect, so we can't rely on the cached value to determine that cmode update in not necessary. Force cmode update in mv88e6341_port_set_cmode(), to make serdes configuration work again. Other mv88e6xxx_port_set_cmode() callers keep the current behaviour. This fixes serdes configuration of the 6141 switch on SolidRun Clearfog GT-8K. Fixes: 7a3007d2 ("net: dsa: mv88e6xxx: fully support SERDES on Topaz family") Reported-by: Denis Odintsov <d.odintsov@traviangames.com> Signed-off-by: Baruch Siach <baruch@tkos.co.il> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
-
- 31 Dec, 2019 11 commits
-
-
git://git.kernel.org/pub/scm/linux/kernel/git/netdev/netLinus Torvalds authored
Pull networking fixes from David Miller: 1) Fix big endian overflow in nf_flow_table, from Arnd Bergmann. 2) Fix port selection on big endian in nft_tproxy, from Phil Sutter. 3) Fix precision tracking for unbound scalars in bpf verifier, from Daniel Borkmann. 4) Fix integer overflow in socket rcvbuf check in UDP, from Antonio Messina. 5) Do not perform a neigh confirmation during a pmtu update over a tunnel, from Hangbin Liu. 6) Fix DMA mapping leak in dpaa_eth driver, from Madalin Bucur. 7) Various PTP fixes for sja1105 dsa driver, from Vladimir Oltean. 8) Add missing to dummy definition of of_mdiobus_child_is_phy(), from Geert Uytterhoeven * git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (54 commits) hsr: fix slab-out-of-bounds Read in hsr_debugfs_rename() net/sched: add delete_empty() to filters and use it in cls_flower tcp: Fix highest_sack and highest_sack_seq ptp: fix the race between the release of ptp_clock and cdev net: dsa: sja1105: Reconcile the meaning of TPID and TPID2 for E/T and P/Q/R/S Documentation: net: dsa: sja1105: Remove text about taprio base-time limitation net: dsa: sja1105: Remove restriction of zero base-time for taprio offload net: dsa: sja1105: Really make the PTP command read-write net: dsa: sja1105: Take PTP egress timestamp by port, not mgmt slot cxgb4/cxgb4vf: fix flow control display for auto negotiation mlxsw: spectrum: Use dedicated policer for VRRP packets mlxsw: spectrum_router: Skip loopback RIFs during MAC validation net: stmmac: dwmac-meson8b: Fix the RGMII TX delay on Meson8b/8m2 SoCs net/sched: act_mirred: Pull mac prior redir to non mac_header_xmit device net_sched: sch_fq: properly set sk->sk_pacing_status bnx2x: Fix accounting of vlan resources among the PFs bnx2x: Use appropriate define for vlan credit of: mdio: Add missing inline to of_mdiobus_child_is_phy() dummy net: phy: aquantia: add suspend / resume ops for AQR105 dpaa_eth: fix DMA mapping leak ...
-
git://git.osdn.net/gitroot/tomoyo/tomoyo-test1Linus Torvalds authored
Pull tomoyo fixes from Tetsuo Handa: "Two bug fixes: - Suppress RCU warning at list_for_each_entry_rcu() - Don't use fancy names on sockets" * tag 'tomoyo-fixes-for-5.5' of git://git.osdn.net/gitroot/tomoyo/tomoyo-test1: tomoyo: Suppress RCU warning at list_for_each_entry_rcu(). tomoyo: Don't use nifty names on sockets.
-
Taehee Yoo authored
hsr slave interfaces don't have debugfs directory. So, hsr_debugfs_rename() shouldn't be called when hsr slave interface name is changed. Test commands: ip link add dummy0 type dummy ip link add dummy1 type dummy ip link add hsr0 type hsr slave1 dummy0 slave2 dummy1 ip link set dummy0 name ap Splat looks like: [21071.899367][T22666] ap: renamed from dummy0 [21071.914005][T22666] ================================================================== [21071.919008][T22666] BUG: KASAN: slab-out-of-bounds in hsr_debugfs_rename+0xaa/0xb0 [hsr] [21071.923640][T22666] Read of size 8 at addr ffff88805febcd98 by task ip/22666 [21071.926941][T22666] [21071.927750][T22666] CPU: 0 PID: 22666 Comm: ip Not tainted 5.5.0-rc2+ #240 [21071.929919][T22666] Hardware name: innotek GmbH VirtualBox/VirtualBox, BIOS VirtualBox 12/01/2006 [21071.935094][T22666] Call Trace: [21071.935867][T22666] dump_stack+0x96/0xdb [21071.936687][T22666] ? hsr_debugfs_rename+0xaa/0xb0 [hsr] [21071.937774][T22666] print_address_description.constprop.5+0x1be/0x360 [21071.939019][T22666] ? hsr_debugfs_rename+0xaa/0xb0 [hsr] [21071.940081][T22666] ? hsr_debugfs_rename+0xaa/0xb0 [hsr] [21071.940949][T22666] __kasan_report+0x12a/0x16f [21071.941758][T22666] ? hsr_debugfs_rename+0xaa/0xb0 [hsr] [21071.942674][T22666] kasan_report+0xe/0x20 [21071.943325][T22666] hsr_debugfs_rename+0xaa/0xb0 [hsr] [21071.944187][T22666] hsr_netdev_notify+0x1fe/0x9b0 [hsr] [21071.945052][T22666] ? __module_text_address+0x13/0x140 [21071.945897][T22666] notifier_call_chain+0x90/0x160 [21071.946743][T22666] dev_change_name+0x419/0x840 [21071.947496][T22666] ? __read_once_size_nocheck.constprop.6+0x10/0x10 [21071.948600][T22666] ? netdev_adjacent_rename_links+0x280/0x280 [21071.949577][T22666] ? __read_once_size_nocheck.constprop.6+0x10/0x10 [21071.950672][T22666] ? lock_downgrade+0x6e0/0x6e0 [21071.951345][T22666] ? do_setlink+0x811/0x2ef0 [21071.951991][T22666] do_setlink+0x811/0x2ef0 [21071.952613][T22666] ? is_bpf_text_address+0x81/0xe0 [ ... ] Reported-by: syzbot+9328206518f08318a5fd@syzkaller.appspotmail.com Fixes: 4c2d5e33 ("hsr: rename debugfs file when interface name is changed") Signed-off-by: Taehee Yoo <ap420073@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Davide Caratti authored
Revert "net/sched: cls_u32: fix refcount leak in the error path of u32_change()", and fix the u32 refcount leak in a more generic way that preserves the semantic of rule dumping. On tc filters that don't support lockless insertion/removal, there is no need to guard against concurrent insertion when a removal is in progress. Therefore, for most of them we can avoid a full walk() when deleting, and just decrease the refcount, like it was done on older Linux kernels. This fixes situations where walk() was wrongly detecting a non-empty filter, like it happened with cls_u32 in the error path of change(), thus leading to failures in the following tdc selftests: 6aa7: (filter, u32) Add/Replace u32 with source match and invalid indev 6658: (filter, u32) Add/Replace u32 with custom hash table and invalid handle 74c2: (filter, u32) Add/Replace u32 filter with invalid hash table id On cls_flower, and on (future) lockless filters, this check is necessary: move all the check_empty() logic in a callback so that each filter can have its own implementation. For cls_flower, it's sufficient to check if no IDRs have been allocated. This reverts commit 275c44aa. Changes since v1: - document the need for delete_empty() when TCF_PROTO_OPS_DOIT_UNLOCKED is used, thanks to Vlad Buslov - implement delete_empty() without doing fl_walk(), thanks to Vlad Buslov - squash revert and new fix in a single patch, to be nice with bisect tests that run tdc on u32 filter, thanks to Dave Miller Fixes: 275c44aa ("net/sched: cls_u32: fix refcount leak in the error path of u32_change()") Fixes: 6676d5e4 ("net: sched: set dedicated tcf_walker flag when tp is empty") Suggested-by: Jamal Hadi Salim <jhs@mojatatu.com> Suggested-by: Vlad Buslov <vladbu@mellanox.com> Signed-off-by: Davide Caratti <dcaratti@redhat.com> Reviewed-by: Vlad Buslov <vladbu@mellanox.com> Tested-by: Jamal Hadi Salim <jhs@mojatatu.com> Acked-by: Jamal Hadi Salim <jhs@mojatatu.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Cambda Zhu authored
>From commit 50895b9d ("tcp: highest_sack fix"), the logic about setting tp->highest_sack to the head of the send queue was removed. Of course the logic is error prone, but it is logical. Before we remove the pointer to the highest sack skb and use the seq instead, we need to set tp->highest_sack to NULL when there is no skb after the last sack, and then replace NULL with the real skb when new skb inserted into the rtx queue, because the NULL means the highest sack seq is tp->snd_nxt. If tp->highest_sack is NULL and new data sent, the next ACK with sack option will increase tp->reordering unexpectedly. This patch sets tp->highest_sack to the tail of the rtx queue if it's NULL and new data is sent. The patch keeps the rule that the highest_sack can only be maintained by sack processing, except for this only case. Fixes: 50895b9d ("tcp: highest_sack fix") Signed-off-by: Cambda Zhu <cambda@linux.alibaba.com> Signed-off-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Vladis Dronov authored
In a case when a ptp chardev (like /dev/ptp0) is open but an underlying device is removed, closing this file leads to a race. This reproduces easily in a kvm virtual machine: ts# cat openptp0.c int main() { ... fp = fopen("/dev/ptp0", "r"); ... sleep(10); } ts# uname -r 5.5.0-rc3-46cf053e ts# cat /proc/cmdline ... slub_debug=FZP ts# modprobe ptp_kvm ts# ./openptp0 & [1] 670 opened /dev/ptp0, sleeping 10s... ts# rmmod ptp_kvm ts# ls /dev/ptp* ls: cannot access '/dev/ptp*': No such file or directory ts# ...woken up [ 48.010809] general protection fault: 0000 [#1] SMP [ 48.012502] CPU: 6 PID: 658 Comm: openptp0 Not tainted 5.5.0-rc3-46cf053e #25 [ 48.014624] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), ... [ 48.016270] RIP: 0010:module_put.part.0+0x7/0x80 [ 48.017939] RSP: 0018:ffffb3850073be00 EFLAGS: 00010202 [ 48.018339] RAX: 000000006b6b6b6b RBX: 6b6b6b6b6b6b6b6b RCX: ffff89a476c00ad0 [ 48.018936] RDX: fffff65a08d3ea08 RSI: 0000000000000247 RDI: 6b6b6b6b6b6b6b6b [ 48.019470] ... ^^^ a slub poison [ 48.023854] Call Trace: [ 48.024050] __fput+0x21f/0x240 [ 48.024288] task_work_run+0x79/0x90 [ 48.024555] do_exit+0x2af/0xab0 [ 48.024799] ? vfs_write+0x16a/0x190 [ 48.025082] do_group_exit+0x35/0x90 [ 48.025387] __x64_sys_exit_group+0xf/0x10 [ 48.025737] do_syscall_64+0x3d/0x130 [ 48.026056] entry_SYSCALL_64_after_hwframe+0x44/0xa9 [ 48.026479] RIP: 0033:0x7f53b12082f6 [ 48.026792] ... [ 48.030945] Modules linked in: ptp i6300esb watchdog [last unloaded: ptp_kvm] [ 48.045001] Fixing recursive fault but reboot is needed! This happens in: static void __fput(struct file *file) { ... if (file->f_op->release) file->f_op->release(inode, file); <<< cdev is kfree'd here if (unlikely(S_ISCHR(inode->i_mode) && inode->i_cdev != NULL && !(mode & FMODE_PATH))) { cdev_put(inode->i_cdev); <<< cdev fields are accessed here Namely: __fput() posix_clock_release() kref_put(&clk->kref, delete_clock) <<< the last reference delete_clock() delete_ptp_clock() kfree(ptp) <<< cdev is embedded in ptp cdev_put module_put(p->owner) <<< *p is kfree'd, bang! Here cdev is embedded in posix_clock which is embedded in ptp_clock. The race happens because ptp_clock's lifetime is controlled by two refcounts: kref and cdev.kobj in posix_clock. This is wrong. Make ptp_clock's sysfs device a parent of cdev with cdev_device_add() created especially for such cases. This way the parent device with its ptp_clock is not released until all references to the cdev are released. This adds a requirement that an initialized but not exposed struct device should be provided to posix_clock_register() by a caller instead of a simple dev_t. This approach was adopted from the commit 72139dfa ("watchdog: Fix the race between the release of watchdog_core_data and cdev"). See details of the implementation in the commit 233ed09d ("chardev: add helper function to register char devs with a struct device"). Link: https://lore.kernel.org/linux-fsdevel/20191125125342.6189-1-vdronov@redhat.com/T/#uAnalyzed-by: Stephen Johnston <sjohnsto@redhat.com> Analyzed-by: Vern Lovejoy <vlovejoy@redhat.com> Signed-off-by: Vladis Dronov <vdronov@redhat.com> Acked-by: Richard Cochran <richardcochran@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Vladimir Oltean authored
For first-generation switches (SJA1105E and SJA1105T): - TPID means C-Tag (typically 0x8100) - TPID2 means S-Tag (typically 0x88A8) While for the second generation switches (SJA1105P, SJA1105Q, SJA1105R, SJA1105S) it is the other way around: - TPID means S-Tag (typically 0x88A8) - TPID2 means C-Tag (typically 0x8100) In other words, E/T tags untagged traffic with TPID, and P/Q/R/S with TPID2. So the patch mentioned below fixed VLAN filtering for P/Q/R/S, but broke it for E/T. We strive for a common code path for all switches in the family, so just lie in the static config packing functions that TPID and TPID2 are at swapped bit offsets than they actually are, for P/Q/R/S. This will make both switches understand TPID to be ETH_P_8021Q and TPID2 to be ETH_P_8021AD. The meaning from the original E/T was chosen over P/Q/R/S because E/T is actually the one with public documentation available (UM10944.pdf). Fixes: f9a1a764 ("net: dsa: sja1105: Reverse TPID and TPID2") Signed-off-by: Vladimir Oltean <olteanv@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Vladimir Oltean authored
Since commit 86db36a3 ("net: dsa: sja1105: Implement state machine for TAS with PTP clock source"), this paragraph is no longer true. So remove it. Signed-off-by: Vladimir Oltean <olteanv@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Vladimir Oltean authored
The check originates from the initial implementation which was not based on PTP time but on a standalone clock source. In the meantime we can now program the PTPSCHTM register at runtime with the dynamic base time (actually with a value that is 200 ns smaller, to avoid writing DELTA=0 in the Schedule Entry Points Parameters Table). And we also have logic for moving the actual base time in the future of the PHC's current time base, so the check for zero serves no purpose, since even if the user will specify zero, that's not what will end up in the static config table where the limitation is. Fixes: 86db36a3 ("net: dsa: sja1105: Implement state machine for TAS with PTP clock source") Signed-off-by: Vladimir Oltean <olteanv@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Vladimir Oltean authored
When activating tc-taprio offload on the switch ports, the TAS state machine will try to check whether it is running or not, but will find both the STARTED and STOPPED bits as false in the sja1105_tas_check_running function. So the function will return -EINVAL (an abnormal situation) and the kernel will keep printing this from the TAS FSM workqueue: [ 37.691971] sja1105 spi0.1: An operation returned -22 The reason is that the underlying function that gets called, sja1105_ptp_commit, does not actually do a SPI_READ, but a SPI_WRITE. So the command buffer remains initialized with zeroes instead of retrieving the hardware state. Fix that. Fixes: 41603d78 ("net: dsa: sja1105: Make the PTP command read-write") Signed-off-by: Vladimir Oltean <olteanv@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Vladimir Oltean authored
The PTP egress timestamp N must be captured from register PTPEGR_TS[n], where n = 2 * PORT + TSREG. There are 10 PTPEGR_TS registers, 2 per port. We are only using TSREG=0. As opposed to the management slots, which are 4 in number (SJA1105_NUM_PORTS, minus the CPU port). Any management frame (which includes PTP frames) can be sent to any non-CPU port through any management slot. When the CPU port is not the last port (#4), there will be a mismatch between the slot and the port number. Luckily, the only mainline occurrence with this switch (arch/arm/boot/dts/ls1021a-tsn.dts) does have the CPU port as #4, so the issue did not manifest itself thus far. Fixes: 47ed985e ("net: dsa: sja1105: Add logic for TX timestamping") Signed-off-by: Vladimir Oltean <olteanv@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
- 30 Dec, 2019 1 commit
-
-
Rahul Lakkireddy authored
As per 802.3-2005, Section Two, Annex 28B, Table 28B-2 [1], when _only_ Rx pause is enabled, both symmetric and asymmetric pause towards local device must be enabled. Also, firmware returns the local device's flow control pause params as part of advertised capabilities and negotiated params as part of current link attributes. So, fix up ethtool's flow control pause params fetch logic to read from acaps, instead of linkattr. [1] https://standards.ieee.org/standard/802_3-2005.html Fixes: c3168cab ("cxgb4/cxgbvf: Handle 32-bit fw port capabilities") Signed-off-by: Surendra Mobiya <surendra@chelsio.com> Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
- 29 Dec, 2019 8 commits
-
-
Linus Torvalds authored
-
David S. Miller authored
Ido Schimmel says: ==================== mlxsw: Couple of fixes This patch set contains two fixes for mlxsw. Please consider both for stable. Patch #1 from Amit fixes a wrong check during MAC validation when creating router interfaces (RIFs). Given a particular order of configuration this can result in the driver refusing to create new RIFs. Patch #2 fixes a wrong trap configuration in which VRRP packets and routing exceptions were policed by the same policer towards the CPU. In certain situations this can prevent VRRP packets from reaching the CPU. ==================== Signed-off-by: David S. Miller <davem@davemloft.net>
-
Ido Schimmel authored
Currently, VRRP packets and packets that hit exceptions during routing (e.g., MTU error) are policed using the same policer towards the CPU. This means, for example, that misconfiguration of the MTU on a routed interface can prevent VRRP packets from reaching the CPU, which in turn can cause the VRRP daemon to assume it is the Master router. Fix this by using a dedicated policer for VRRP packets. Fixes: 11566d34 ("mlxsw: spectrum: Add VRRP traps") Signed-off-by: Ido Schimmel <idosch@mellanox.com> Reported-by: Alex Veber <alexve@mellanox.com> Tested-by: Alex Veber <alexve@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Amit Cohen authored
When a router interface (RIF) is created the MAC address of the backing netdev is verified to have the same MSBs as existing RIFs. This is required in order to avoid changing existing RIF MAC addresses that all share the same MSBs. Loopback RIFs are special in this regard as they do not have a MAC address, given they are only used to loop packets from the overlay to the underlay. Without this change, an error is returned when trying to create a RIF after the creation of a GRE tunnel that is represented by a loopback RIF. 'rif->dev->dev_addr' points to the GRE device's local IP, which does not share the same MSBs as physical interfaces. Adding an IP address to any physical interface results in: Error: mlxsw_spectrum: All router interface MAC addresses must have the same prefix. Fix this by skipping loopback RIFs during MAC validation. Fixes: 74bc9939 ("mlxsw: spectrum_router: Veto unsupported RIF MAC addresses") Signed-off-by: Amit Cohen <amitc@mellanox.com> Signed-off-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linuxLinus Torvalds authored
Pull RISC-V fixes from Paul Walmsley: "One important fix for RISC-V: - Redirect any incoming syscall with an ID less than -1 to sys_ni_syscall, rather than allowing them to fall through into the syscall handler. and two minor build fixes: - Export __asm_copy_{from,to}_user() from where they are defined. This fixes a build error triggered by some randconfigs. - Export flush_icache_all(). I'd resisted this before, since historically we didn't want modules to be able to flush the I$ directly; but apparently everyone else is doing it now" * tag 'riscv/for-v5.5-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux: riscv: export flush_icache_all to modules riscv: reject invalid syscalls below -1 riscv: fix compile failure with EXPORT_SYMBOL() & !MMU
-
git://git.kernel.org/pub/scm/linux/kernel/git/jlayton/linuxLinus Torvalds authored
Pull /proc/locks formatting fix from Jeff Layton: "This is a trivial fix for a _very_ long standing bug in /proc/locks formatting. Ordinarily, I'd wait for the merge window for something like this, but it is making it difficult to validate some overlayfs fixes. I've also gone ahead and marked this for stable" * tag 'locks-v5.5-1' of git://git.kernel.org/pub/scm/linux/kernel/git/jlayton/linux: locks: print unsigned ino in /proc/locks
-
git://git.samba.org/sfrench/cifs-2.6Linus Torvalds authored
Pull cifs fixes from Steve French: "One performance fix for large directory searches, and one minor style cleanup noticed by Clang" * tag '5.5-rc3-smb3-fixes' of git://git.samba.org/sfrench/cifs-2.6: cifs: Optimize readdir on reparse points cifs: Adjust indentation in smb2_open_file
-
Amir Goldstein authored
An ino is unsigned, so display it as such in /proc/locks. Cc: stable@vger.kernel.org Signed-off-by: Amir Goldstein <amir73il@gmail.com> Signed-off-by: Jeff Layton <jlayton@kernel.org>
-
- 28 Dec, 2019 6 commits
-
-
Olof Johansson authored
This is needed by LKDTM (crash dump test module), it calls flush_icache_range(), which on RISC-V turns into flush_icache_all(). On other architectures, the actual implementation is exported, so follow that precedence and export it here too. Fixes build of CONFIG_LKDTM that fails with: ERROR: "flush_icache_all" [drivers/misc/lkdtm/lkdtm.ko] undefined! Signed-off-by: Olof Johansson <olof@lixom.net> Signed-off-by: Paul Walmsley <paul.walmsley@sifive.com>
-
David Abdurachmanov authored
Running "stress-ng --enosys 4 -t 20 -v" showed a large number of kernel oops with "Unable to handle kernel paging request at virtual address" message. This happens when enosys stressor starts testing random non-valid syscalls. I forgot to redirect any syscall below -1 to sys_ni_syscall. With the patch kernel oops messages are gone while running stress-ng enosys stressor. Signed-off-by: David Abdurachmanov <david.abdurachmanov@sifive.com> Fixes: 5340627e ("riscv: add support for SECCOMP and SECCOMP_FILTER") Signed-off-by: Paul Walmsley <paul.walmsley@sifive.com>
-
Luc Van Oostenryck authored
When support for !MMU was added, the declaration of __asm_copy_to_user() & __asm_copy_from_user() were #ifdefed out hence their EXPORT_SYMBOL() give an error message like: .../riscv_ksyms.c:13:15: error: '__asm_copy_to_user' undeclared here .../riscv_ksyms.c:14:15: error: '__asm_copy_from_user' undeclared here Since these symbols are not defined with !MMU it's wrong to export them. Same for __clear_user() (even though this one is also declared in include/asm-generic/uaccess.h and thus doesn't give an error message). Fix this by doing the EXPORT_SYMBOL() directly where these symbols are defined: inside lib/uaccess.S itself. Fixes: 6bd33e1e ("riscv: fix compile failure with EXPORT_SYMBOL() & !MMU") Reported-by: kbuild test robot <lkp@intel.com> Cc: Christoph Hellwig <hch@lst.de> Cc: Palmer Dabbelt <palmer@dabbelt.com> Cc: Paul Walmsley <paul.walmsley@sifive.com> Signed-off-by: Luc Van Oostenryck <luc.vanoostenryck@gmail.com> Signed-off-by: Paul Walmsley <paul.walmsley@sifive.com>
-
git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsiLinus Torvalds authored
Pull SCSI fixes from James Bottomley: "Four fixes and one spelling update, all in drivers: two in lpfc and the rest in mp3sas, cxgbi and target" * tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: scsi: target/iblock: Fix protection error with blocks greater than 512B scsi: libcxgbi: fix NULL pointer dereference in cxgbi_device_destroy() scsi: lpfc: fix spelling mistakes of asynchronous scsi: lpfc: fix build failure with DEBUGFS disabled scsi: mpt3sas: Fix double free in attach error handling
-
Martin Blumenstingl authored
GXBB and newer SoCs use the fixed FCLK_DIV2 (1GHz) clock as input for the m250_sel clock. Meson8b and Meson8m2 use MPLL2 instead, whose rate can be adjusted at runtime. So far we have been running MPLL2 with ~250MHz (and the internal m250_div with value 1), which worked enough that we could transfer data with an TX delay of 4ns. Unfortunately there is high packet loss with an RGMII PHY when transferring data (receiving data works fine though). Odroid-C1's u-boot is running with a TX delay of only 2ns as well as the internal m250_div set to 2 - no lost (TX) packets can be observed with that setting in u-boot. Manual testing has shown that the TX packet loss goes away when using the following settings in Linux (the vendor kernel uses the same settings): - MPLL2 clock set to ~500MHz - m250_div set to 2 - TX delay set to 2ns on the MAC side Update the m250_div divider settings to only accept dividers greater or equal 2 to fix the TX delay generated by the MAC. iperf3 results before the change: [ ID] Interval Transfer Bitrate Retr [ 5] 0.00-10.00 sec 182 MBytes 153 Mbits/sec 514 sender [ 5] 0.00-10.00 sec 182 MBytes 152 Mbits/sec receiver iperf3 results after the change (including an updated TX delay of 2ns): [ ID] Interval Transfer Bitrate Retr Cwnd [ 5] 0.00-10.00 sec 927 MBytes 778 Mbits/sec 0 sender [ 5] 0.00-10.01 sec 927 MBytes 777 Mbits/sec receiver Fixes: 4f6a71b8 ("net: stmmac: dwmac-meson8b: fix internal RGMII clock configuration") Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Shmulik Ladkani authored
There's no skb_pull performed when a mirred action is set at egress of a mac device, with a target device/action that expects skb->data to point at the network header. As a result, either the target device is errornously given an skb with data pointing to the mac (egress case), or the net stack receives the skb with data pointing to the mac (ingress case). E.g: # tc qdisc add dev eth9 root handle 1: prio # tc filter add dev eth9 parent 1: prio 9 protocol ip handle 9 basic \ action mirred egress redirect dev tun0 (tun0 is a tun device. result: tun0 errornously gets the eth header instead of the iph) Revise the push/pull logic of tcf_mirred_act() to not rely on the skb_at_tc_ingress() vs tcf_mirred_act_wants_ingress() comparison, as it does not cover all "pull" cases. Instead, calculate whether the required action on the target device requires the data to point at the network header, and compare this to whether skb->data points to network header - and make the push/pull adjustments as necessary. Fixes: 1da177e4 ("Linux-2.6.12-rc2") Signed-off-by: Shmulik Ladkani <sladkani@proofpoint.com> Tested-by: Jamal Hadi Salim <jhs@mojatatu.com> Acked-by: Jamal Hadi Salim <jhs@mojatatu.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
- 27 Dec, 2019 8 commits
-
-
git://anongit.freedesktop.org/drm/drmLinus Torvalds authored
Pull drm fixes from Dave Airlie: "Post-xmas food coma recovery fixes. Only three fixes for i915 since I expect most people are holidaying. i915: - power management rc6 fix - framebuffer tracking fix - display power management ratelimit fix" * tag 'drm-fixes-2019-12-28' of git://anongit.freedesktop.org/drm/drm: drm/i915: Hold reference to intel_frontbuffer as we track activity drm/i915/gt: Ratelimit display power w/a drm/i915/pmu: Ensure monotonic rc6
-
Linus Torvalds authored
Merge tag 'linux-kselftest-5.5-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/shuah/linux-kselftest Pull Kselftest fixes from Shuah Khan: - rseq build failures fixes related to glibc 2.30 compatibility from Mathieu Desnoyers - Kunit fixes and cleanups from SeongJae Park - Fixes to filesystems/epoll, firmware, and livepatch build failures and skip handling. * tag 'linux-kselftest-5.5-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/shuah/linux-kselftest: rseq/selftests: Clarify rseq_prepare_unload() helper requirements rseq/selftests: Fix: Namespace gettid() for compatibility with glibc 2.30 rseq/selftests: Turn off timeout setting kunit/kunit_tool_test: Test '--build_dir' option run kunit: Rename 'kunitconfig' to '.kunitconfig' kunit: Place 'test.log' under the 'build_dir' kunit: Create default config in '--build_dir' kunit: Remove duplicated defconfig creation docs/kunit/start: Use in-tree 'kunit_defconfig' selftests: livepatch: Fix it to do root uid check and skip selftests: firmware: Fix it to do root uid check and skip selftests: filesystems/epoll: fix build error
-
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pmLinus Torvalds authored
Pull power management fixes from Rafael Wysocki: "Fix compile test of the Tegra devfreq driver (Arnd Bergmann) and remove redundant Kconfig dependencies from multiple devfreq drivers (Leonard Crestez)" * tag 'pm-5.5-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: PM / devfreq: tegra: Add COMMON_CLK dependency PM / devfreq: Drop explicit selection of PM_OPP
-
git://git.kernel.dk/linux-blockLinus Torvalds authored
Pull io_uring fixes from Jens Axboe: - Removal of now unused busy wqe list (Hillf) - Add cond_resched() to io-wq work processing (Hillf) - And then the series that I hinted at from last week, which removes the sqe from the io_kiocb and keeps all sqe handling on the prep side. This guarantees that an opcode can't do the wrong thing and read the sqe more than once. This is unchanged from last week, no issues have been observed with this in testing. Hence I really think we should fold this into 5.5. * tag 'io_uring-5.5-20191226' of git://git.kernel.dk/linux-block: io-wq: add cond_resched() to worker thread io-wq: remove unused busy list from io_sqe io_uring: pass in 'sqe' to the prep handlers io_uring: standardize the prep methods io_uring: read 'count' for IORING_OP_TIMEOUT in prep handler io_uring: move all prep state for IORING_OP_{SEND,RECV}_MGS to prep handler io_uring: move all prep state for IORING_OP_CONNECT to prep handler io_uring: add and use struct io_rw for read/writes io_uring: use u64_to_user_ptr() consistently
-
git://git.kernel.dk/linux-blockLinus Torvalds authored
Pull libata fixes from Jens Axboe: "Two things in here: - First half of a series that fixes ahci_brcm, also marked for stable. The other part of the series is going into 5.6 (Florian) - sata_nv regression fix that is also marked for stable (Sascha)" * tag 'libata-5.5-20191226' of git://git.kernel.dk/linux-block: ata: ahci_brcm: Add missing clock management during recovery ata: ahci_brcm: BCM7425 AHCI requires AHCI_HFLAG_DELAY_ENGINE ata: ahci_brcm: Fix AHCI resources management ata: libahci_platform: Export again ahci_platform_<en/dis>able_phys() libata: Fix retrieving of active qcs
-
git://git.kernel.dk/linux-blockLinus Torvalds authored
Pull block fixes from Jens Axboe: "Only thing here are the changes from Arnd from last week, which now have the appropriate header include to ensure they actually compile if COMPAT is enabled" * tag 'block-5.5-20191226' of git://git.kernel.dk/linux-block: compat_ioctl: block: handle Persistent Reservations compat_ioctl: block: handle add zone open, close and finish ioctl compat_ioctl: block: handle BLKGETZONESZ/BLKGETNRZONES compat_ioctl: block: handle BLKREPORTZONE/BLKRESETZONE pktcdvd: fix regression on 64-bit architectures
-
git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpioLinus Torvalds authored
Pull GPIO fixes from Linus Walleij: "A set of fixes for the v5.5 series: - Fix the build for the Xtensa driver. - Make sure to set up the parent device for mpc8xxx. - Clarify the look-up error message. - Fix the usage of the line direction in the mockup device. - Fix a type warning on the Aspeed driver. - Remove the pointless __exit annotation on the xgs-iproc which is causing a compilation problem. - Fix up emultation of open drain outputs .get_direction() - Fix the IRQ callbacks on the PCA953xx to use bitops and work properly. - Fix the Kconfig on the Tegra driver" * tag 'gpio-v5.5-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: gpio: tegra186: Allow building on Tegra194-only configurations gpio: pca953x: Switch to bitops in IRQ callbacks gpiolib: fix up emulated open drain outputs MAINTAINERS: Append missed file to the database gpio: xgs-iproc: remove __exit annotation for iproc_gpio_remove gpio: aspeed: avoid return type warning gpio: mockup: Fix usage of new GPIO_LINE_DIRECTION gpio: Fix error message on out-of-range GPIO in lookup table gpio: mpc8xxx: Add platform device to gpiochip->parent gpio: xtensa: fix driver build
-
Dave Airlie authored
Merge tag 'drm-intel-fixes-2019-12-23' of git://anongit.freedesktop.org/drm/drm-intel into drm-fixes i915 power and frontbuffer tracking fixes Signed-off-by: Dave Airlie <airlied@redhat.com> From: Jani Nikula <jani.nikula@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/87r20vdlrs.fsf@intel.com
-