This allows offb to be used for initial framebuffer,
and a kms driver to take over later in the boot sequence.
Signed-off-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>

This is a libata driver for the "macio" IDE controller used on most Apple
PowerMac and PowerBooks. It's a libata equivalent of drivers/ide/ppc/pmac.c

It supports all the features of its predecessor, including mediabay hotplug
and suspend/resume. It should also support module load/unload.

The timing calculations have been simplified to use pre-calculated tables
compared to drivers/ide/pmac.c and it uses the new mediabay interface
provided by a previous patch.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Tejun Heo <tj@kernel.org>

In libata-sff, ata_sff_post_internal_cmd() directly calls ata_bmdma_stop()
instead of ap->ops->bmdma_stop(). This can be a problem for controllers
that use their own bmdma_stop for which the generic sff one isn't suitable
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Jeff Garzik <jgarzik@redhat.com>

The hotplug mediabay has tendrils deep into drivers/ide code
which makes a libata port reather difficult. In addition it's
ugly and could be done better.

This reworks the interface between the mediabay and the rest
of the world so that:

   - Any macio_driver can now have a mediabay_event callback
which will be called when that driver sits on a mediabay and
it's been either plugged or unplugged. The device type is
passed as an argument. We can now move all the IDE cruft
into the IDE driver itself

   - A check_media_bay() function can be used to take a peek
at the type of device currently in the bay if any, a cleaner
variant of the previous function with the same name.

   - A pair of lock/unlock functions are exposed to allow the
IDE driver to block the hotplug callbacks during the initial
setup and probing of the bay in order to avoid nasty race
conditions.

   - The mediabay code no longer needs to spin on the status
register of the IDE interface when it detects an IDE device,
this is done just fine by the IDE code itself

Overall, less code, simpler, and allows for another driver
than our old drivers/ide based one.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>

This adds dma_parms to macio devices and initializes them with
default values. This will allow pata_macio to setup the appropriate
max segment size for the block layer.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>

This adds some basic devres support. When enabled via macio_enable_devres()
resources requested by drivers will be automatically released.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>

Currently userspace has no chance to find out which virtual address space we're
in and resolve addresses. While that is a big problem for migration, it's also
unpleasent when debugging, as gdb and the monitor don't work on virtual
addresses.

This patch exports enough of the MMU segment state to userspace to make
debugging work and thus also includes the groundwork for migration.
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>

The virtio console, which uses hvc, will get the ability to hot-unplug
ports. Export hvc_remove so that virtio_console can disassociate with
hvc.
Signed-off-by: Amit Shah <amit.shah@redhat.com>
Cc: linuxppc-dev@ozlabs.org
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>

Windfarm SMU control is explicitly missing support for a second CPU pump in G5 PowerMacs. Such machines actually exist  (specifically Quads with a second pump), so this patch adds detection for it.

Signed-off by: Bolko Maass <bmaass@math.uni-bremen.de>
CC: <stable@kernel.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>

Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>

Commit a0668cdc cleans up the handling
of kmem_caches for allocating various levels of pagetables.
Unfortunately, it conflicts badly with CONFIG_PPC_SUBPAGE_PROT, due to
the latter's cleverly hidden technique of adding some extra allocation
space to the top level page directory to store the extra information
it needs.

Since that extra allocation really doesn't fit into the cleaned up
page directory allocating scheme, this patch alters
CONFIG_PPC_SUBPAGE_PROT to instead allocate its struct
subpage_prot_table as part of the mm_context_t.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>

This reverts commit c045256d.

It breaks build when CONFIG_PPC_SUBPAGE_PROT is not set. I will
commit a fixed version separately
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>

Many boards have a bug-free ns16550 compatible serial port, which we should
register as PORT_16550A. This introduces a new value "ns16550a" for the
compatible property of of_serial to let a firmware choose that model instead
of using the crippled PORT_16550 mode.
Reported-by: Alon Ziv <alonz@nolaviz.org>
Signed-off-by: Michal Simek <monstr@monstr.eu>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>

Commit a4fe3ce7 introduced a new
get_user_pages() path for hugepages on powerpc.  Unfortunately, there
is a bug in it's loop logic, which can cause it to overrun the end of
the intended region.  This came about by copying the logic from the
normal page path, which assumes the address and end parameters have
been pagesize aligned at the top-level.  Since they're not *hugepage*
size aligned, the simplistic logic could step over the end of the gup
region without triggering the loop end condition.

This patch fixes the bug by using the technique that the normal page
path uses in levels above the lowest to truncate the ending address to
something we know we'll match with.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>

Commit a0668cdc cleans up the handling
of kmem_caches for allocating various levels of pagetables.
Unfortunately, it conflicts badly with CONFIG_PPC_SUBPAGE_PROT, due to
the latter's cleverly hidden technique of adding some extra allocation
space to the top level page directory to store the extra information
it needs.

Since that extra allocation really doesn't fit into the cleaned up
page directory allocating scheme, this patch alters
CONFIG_PPC_SUBPAGE_PROT to instead allocate its struct
subpage_prot_table as part of the mm_context_t.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>

Commit 87ec0e98 in kumar's next branch
broke one of my test configs since it looks like Anton forgot about
that mpc832x_rdb platform which still uses the old style probing for
the SPI stuff.

I'll let them do a cleaner fix that probably involves changing the
probing method and getting rid of the platform device but for now
this will do to fix it.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>

This patch was submitted, discussed, and eventually Acked by everyone, yet
still isn't in the tree.  See:

http://patchwork.ozlabs.org/patch/1240/Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Cc: Arnd Bergmann <arnd@anrdb.de>
Cc: Paul Mackerras <paulus@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>

Code was added to mm/higmem.c that depends on several
kmap types that powerpc does not support.  We add dummy
invalid definitions for KM_NMI, KM_NM_PTE, and KM_IRQ_PTE.

According to list discussion, this fix should not be needed
anymore starting with 2.6.33.  The code is commented to this
effect so hopefully we will remember to remove this.
Signed-off-by: Becky Bruce <beckyb@kernel.crashing.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>

We can kill unused swiotlb variable.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>

Since they are static inline functions.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>

The code under "if (is_global_init())" is bogus, and is_global_init()
itself is not right in mt case.

Contrary to what the comment says, nowadays force_sig_info() does kill
init even if the handler is SIG_DFL. Note that force_sig_info() clears
SIGNAL_UNKILLABLE exactly for this case.
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>

When a CPU is offlined on POWER currently, we call rtas_stop_self() and hand
the CPU back to the resource pool. This path is used for DLPAR which will
cause a change in the LPAR configuration which will be visible outside.

This patch changes the default state a CPU is put into when it is offlined.
On platforms which support ceding the processor to the hypervisor with
latency hint specifier value, during a cpu offline operation,
instead of calling rtas_stop_self(), we cede the vCPU to the hypervisor
while passing a latency hint specifier value. The Hypervisor can use this hint
to provide better energy savings. Also, during the offline
operation, the control of the vCPU remains with the LPAR as oppposed to
returning it to the resource pool.

The patch achieves this by creating an infrastructure to set the
preferred_offline_state() which can be either
- CPU_STATE_OFFLINE: which is the current behaviour of calling
  rtas_stop_self()

- CPU_STATE_INACTIVE: which cedes the vCPU to the hypervisor with the latency
  hint specifier.

The codepath which wants to perform a DLPAR operation can set the
preferred_offline_state() of a CPU to CPU_STATE_OFFLINE before invoking
cpu_down().

The patch also provides a boot-time command line argument to disable/enable
CPU_STATE_INACTIVE.
Signed-off-by: Gautham R Shenoy <ego@in.ibm.com>
Signed-off-by: Nathan Fontenot <nfont@austin.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>

This patch provides an extended_cede_processor() helper function
which takes the cede latency hint as an argument. This hint is to be passed
on to the hypervisor to cede to the corresponding state on platforms
which support it.
Signed-off-by: Gautham R Shenoy <ego@in.ibm.com>
Signed-off-by: Arun R Bharadwaj <arun@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>

Move ehea hcall definitions into hvcall.h.
Signed-off-by: Anton Blanchard <anton@samba.org>
Acked-by: Thomas Klein <tklein@de.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>

The typename member of struct irq_chip was kept for migration purposes
and is obsolete since more than 2 years. Fix up the leftovers.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: linuxppc-dev@ozlabs.org
Acked-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>

SPIN_LOCK_UNLOCKED is deprecated. Init the lock array at runtime
instead.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: linuxppc-dev@ozlabs.org
Tested-by: Stephen Rothwell <sfr@canb.auug.org.au>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>

Drop the bkl from nvram_llseek() as it obviously protects nothing. The
file offset is safe in essence.

The ioctl can be converted to unlocked_ioctl because it just calls
pmac_get_partition() which reads a value from an array which was
initialized at early boot time. No need for serialization.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: linuxppc-dev@ozlabs.org
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>

The ioctl is only used for powermac systems and reads a partition
number from an array which is initialized at boot time way before the
nvram code is initialized. So it's safe to switch to unlocked_ioctl.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: linuxppc-dev@ozlabs.org
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>

size_t len cannot be less than 0.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Acked-by: Jeremy Kerr <jk@ozlabs.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>

Add basic support for the P4080 DS reference board.  None of the data
path devices (ethernet, crypto, pme) are support at this time.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>

Add support for NVRAM on GE Fanuc's PPC9A.
Signed-off-by: Martyn Welch <martyn.welch@gefanuc.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>

Add support for NVRAM on GE Fanuc's SBC310.
Signed-off-by: Martyn Welch <martyn.welch@gefanuc.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>

This patch enables the NVRAM found on the GE Fanuc SBC610
Signed-off-by: Martyn Welch <martyn.welch@gefanuc.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>

Re-write the code so its more standalone and fixed some issues:
* Bump'd # of CAM entries to 64 to support e500mc
* Make the code handle MAS7 properly
* Use pr_cont instead of creating a string as we go
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>

Introduce new FSL_SOC_BOOKE Kconfig to handle both 85xx and QorIQ
based chips.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>

* 'i2c-pnx-fixes' of git://git.fluff.org/bjdooks/linux:
  i2c: i2c-pnx: Added missing mach/i2c.h and linux/io.h header file includes
  i2c: i2c-pnx: Made buf type unsigned to prevent sign extension
  i2c: i2c-pnx: Limit minimum jiffie timeout to 2

* 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jlbec/ocfs2:
  ocfs2: Trivial cleanup of jbd compatibility layer removal
  ocfs2: Refresh documentation
  ocfs2: return f_fsid info in ocfs2_statfs()
  ocfs2: duplicate inline data properly during reflink.
  ocfs2: Move ocfs2_complete_reflink to the right place.
  ocfs2: Return -EINVAL when a device is not ocfs2.