Merge "Broadcom Device Tree changes for 4.1 #3" from Brian Norris:

This pull request contains changes to the BCM7445 reference DTS files from
Brian:

- making a clock-frequency property decimal instead of hexadecimal

- adding the irq0 interrupt controller node to make the reference DTS bootable
  again

* tag 'arm-soc/for-4.1/devicetree-part-3' of http://github.com/broadcom/stblinux:
  ARM: dts: brcmstb: add IRQ0 controller
  ARM: dts: brcmstb: un-hexify clock frequency
Signed-off-by: Olof Johansson <olof@lixom.net>

Merge tag 'at91-dt2' of git://git.kernel.org/pub/scm/linux/kernel/git/nferre/linux-at91 into next/dt

Merge "at91: dt for 4.1 #2" from Nicolas Ferre:

Second batch of DT changes for 4.1:
- RTC nodes for at91sam9x5 boards and at91sam9n12ek
- HLCDC nodes and pin definitions for sama5d3 & sama5d4
- additional uarts for sama5d3

* tag 'at91-dt2' of git://git.kernel.org/pub/scm/linux/kernel/git/nferre/linux-at91:
  ARM: at91/dt: sama5d4: add rgb777 LCD line configuration
  ARM: at91/dt: sama5d4: fix LCD pins for RGB666 format
  ARM: at91/dt: sama5d4: add hlcdc node
  ARM: at91/dt: sama5d4: add lcdc pin definitions
  ARM: at91/dt: sama5d3: add uart1 pinctrl definition
  ARM: at91/dt: sama5d3: add uart0
  ARM: at91/dt: define the HLCDC node available on sama5d3 SoCs
  ARM: at91/dt: add alternative pin muxing for sama5d3 lcd pins
  ARM: at91/dt: split sama5d3 lcd pin definitions to match RGB mode configs
  ARM: at91/dt: at91sam9n12ek: enable RTC
  ARM: at91/dt: at91sam9x5cm: enable RTC
  DT: video: atmel_lcdc: Add example of fixed framebuffer memory
Signed-off-by: Olof Johansson <olof@lixom.net>

Merge "ARM: mvebu: dt changes for v4.1 (round 2)" from Gregory Clement:

mvebu dt changes for v4.1 (part #2)

- add support for Performance Monitor Unit on most of mvebu SoCs
- add nas2big support
- add support for USB3 port On Armada 385 AP

* tag 'mvebu-dt-4.1-2' of git://git.infradead.org/linux-mvebu:
  ARM: mvebu: armada-385-ap: Enable USB3 port
  ARM: mvebu: Enable Performance Monitor Unit on Armada 380/385 SoC
  ARM: mvebu: Enable Performance Monitor Unit on Armada 375 SoC
  ARM: mvebu: Enable Performance Monitor Unit on Armada XP/370 SoCs
  ARM: Kirkwood: add DT description for nas2big
Signed-off-by: Olof Johansson <olof@lixom.net>

Merge "omap device tree changes for v4.1, part1" from Tony Lindgren:

Device tree related changes for omaps:

- Add support for ChiliSOM

- Add support for OpenPandora

- Add support for BeagleBoard NAND

- Enable crypto devices for omap3 devices

- Add bindings for omap3 camera support

- Updates for am437x and dra7x and dm816x SoCs

* tag 'v4.1-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap: (27 commits)
  ARM: dts: Update Nanobone dts file
  ARM: dts: n950, n9: Add primary camera support
  ARM: dts: omap3: Add DT entries for OMAP 3 ISP
  Documentation: DT: Add bindings for omap3isp
  ARM: dts: Remove files omap34xx-hs.dtsi and omap36xx-hs.dtsi
  ARM: dts: omap3-tao3530: Include directly omap34xx.dtsi
  ARM: dts: n900: Enable omap sham and include directly omap34xx.dtsi
  ARM: dts: n9/n950: Enable omap crypto support
  ARM: dts: Remove PIN_INPUT for dm816x McSPI
  ARM: dts: Add cppi41 support for dm816x MUSB
  ARM: dts: Fix typo for dm816x usb0_pins
  ARM: dts: dra7x-evm: beagle-x15: Fix USB Peripheral
  ARM: dts: am57xx-beagle-x15: Do not include the atl header
  ARM: dts: DRA7: Remove ti,timer-dsp and ti,timer-pwm properties
  Documentation: omap-twl4030: Move ti,codec property to optional
  ARM: dts: omap3: Remove all references to ti,codec property
  ARM: dts: omap3-beagle: Add NAND device
  ARM: dts: AM4372: update hdq compatible property
  ARM: dts: omap3-pandora: add DM3730 1 GHz version
  ARM: dts: omap3-pandora: add OMAP3530 600 MHz version
  ...
Signed-off-by: Olof Johansson <olof@lixom.net>

Merge tag 'renesas-dt3-for-v4.1' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into next/dt

Merge "Third Round of Renesas ARM Based SoC DT Updates for v4.1" from Simon
Horman:

* Add DMA sound support to r8a7791 and r8a7790 SoCs

* tag 'renesas-dt3-for-v4.1' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
  ARM: shmobile: r8a7791: sound enables Audio DMAC entry on DTSI
  ARM: shmobile: r8a7790: sound enables Audio DMAC entry on DTSI
  ARM: shmobile: r8a7791: enable Audio DMAC peri peri via sound driver
  ARM: shmobile: r8a7790: enable Audio DMAC peri peri via sound driver
  ARM: shmobile: r8a7791: add reg-names for sound
  ARM: shmobile: r8a7790: add reg-names for sound
Signed-off-by: Olof Johansson <olof@lixom.net>

Merge tag 'v4.1-rockchip-dts1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip into next/dt

Merge "ARM: rockchip: dts changes for 4.1" from Heiko Stuebner:

This adds and enables the usbphy nodes on the rk3288 boards and enables
the gmac on the firefly board. A new board the Popmetal-rk3288 is also
added. And finally the pmic supplies for act8846 based boards are added,
as the act8865/act8846 driver gained supply handling in the regulator tree.

* tag 'v4.1-rockchip-dts1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip:
  ARM: dts: rockchip: complete rk3288-evb pmic supplies
  ARM: dts: rockchip: add input supplies for the act8846 on Radxa Rock
  ARM: dts: add rk3288 PopMetal board
  dt-bindings: add root compatible property for PopMetal board
  ARM: dts: rockchip: enable gmac on rk3288-firefly
  ARM: dts: rockchip: enable usbphy on rk3288-firefly
  ARM: dts: rockchip: Enable usb PHY on rk3288-evb board
  ARM: dts: rockchip: add rk3288 usb PHY
Signed-off-by: Olof Johansson <olof@lixom.net>

File uses dash in the filename, not underscore.
Reported-by: Russell King <linux@arm.linux.org.uk>
Signed-off-by: Olof Johansson <olof@lixom.net>

For the SAMA5D4 SoC, some LCD lines are in conflict with useful peripherals.
Remove these lines and the lowest significant bit of a 24 bit LCD. It gives
us a RGB 777 configuration.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>

The color arrangement for SAMA5D4 in RGB 666 takes the most significant bits of
each color line groups.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>

Add HLCDC node.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>

Add LCDC pin definitions.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>

Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>

Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>

Define the HLCDC (HLCD Controller) IP available on some sama5d3 SoCs
(i.e. sama5d31, sama5d33, sama5d34 and sama5d36) in sama5d3 dtsi file.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Tested-by: Anthony Harivel <anthony.harivel@emtrion.de>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>

Define alternative pin muxing for the LCDC pins.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Tested-by: Anthony Harivel <anthony.harivel@emtrion.de>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>

The HLCDC (HLCD Controller) IP supports 4 different output mode (RGB444,
RGB565, RGB666 and RGB888) and the pin muxing will depend on the chosen
RGB mode.

Split pin definitions to be able to set pin config according to the
selected mode.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Tested-by: Anthony Harivel <anthony.harivel@emtrion.de>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>

Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>

Enable RTC for all the at91sam9x5 CPU Modules: this will enable it for all the
EK boards.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>

This drivers allows a fixed framebuffer memory to be set by an additional
IORESOURCE_MEM resource. Thus add an example to the DT documentation.
Signed-off-by: Alexander Stein <alexander.stein@systec-electronic.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>

Update dts file to reflect:-
* new flash memory layout
* add missing phy-mode property
* dual_emac now just a boolean
* rename mcp to microchip
* update gpio definition
Signed-off-by: Mark Jackson <mpfj@newflow.co.uk>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Add support for the primary camera of the Nokia N950 and N9.
Signed-off-by: Sakari Ailus <sakari.ailus@iki.fi>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

The resources the ISP needs are slightly different on 3[45]xx and 3[67]xx.
Especially the phy-type property is different.
Signed-off-by: Sakari Ailus <sakari.ailus@iki.fi>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
[tony@atomide.com: use omap3_scm_general instead of scm_conf for now]
Signed-off-by: Tony Lindgren <tony@atomide.com>

Signed-off-by: Sakari Ailus <sakari.ailus@iki.fi>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

This L2 controller handles multiplexing a few different interrupts. We
also need it for configuring the interrupt forwarding masks for the
UART.

With this, we can *now* boot BCM7445 to a prompt using the upstream
kernel + DTB.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>

These files are not used by any DTS file anymore.
Signed-off-by: Pali Rohár <pali.rohar@gmail.com>
Acked-by: Pavel  Machek <pavel@ucw.cz>
Signed-off-by: Tony Lindgren <tony@atomide.com>

This value makes much more sense in decimal.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Acked-by: Gregory Fong <gregory.0xf0@gmail.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>

This patch just move content of file omap34xx-hs.dtsi into omap3-tao3530.dts.
There is no code change, patch is just preparation for removing -hs file.
Signed-off-by: Pali Rohár <pali.rohar@gmail.com>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Tony Lindgren <tony@atomide.com>

This patch moves content of file omap34xx-hs.dtsi into omap3-n900.dts and enable
omap sham support (omap HW support for SHA + MD5). After testing both omap hwmod
and omap-sham.ko drivers it looks like signed Nokia X-Loader enable L3 firewall
for omap sham. There is no kernel crash with both official bootloader and crypto
enable bootloader. So we can safely enable sham code.
Signed-off-by: Pali Rohár <pali.rohar@gmail.com>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Harmattan system on Nokia N9 and N950 devices uses omap crypto support.
Bootloader on those devices is known that it enables HW crypto support.
This patch just include omap36xx.dtsi directly, so aes and sham is enabled.
Signed-off-by: Pali Rohár <pali.rohar@gmail.com>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Tony Lindgren <tony@atomide.com>

On dm816x we have no PIN_INPUT vs PIN_OUTPUT configuration, there
are just pulls. Let's remove the bogus flags.

Cc: Brian Hutchinson <b.hutchman@gmail.com>
Cc: Matthijs van Duin <matthijsvanduin@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Looks like we have cppi41 on dm816x just like on am335x.

Cc: Bin Liu <binmlist@gmail.com>
Cc: Brian Hutchinson <b.hutchman@gmail.com>
Cc: Felipe Balbi <balbi@ti.com>
Cc: Matthijs van Duin <matthijsvanduin@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Commit a54879a0 ("ARM: dts: Fix USB dts configuration for dm816x")
attempted to fix the USB features introduced by commit 7800064b
("ARM: dts: Add basic dm816x device tree configuration") but obviously
I did not read the dmesg as more USB issues still keep trickling in.

It should be usb1_pins instead not usb0_pins for the second interface
to avoid warnings from pinctrl framework.

Cc: Brian Hutchinson <b.hutchman@gmail.com>
Cc: Felipe Balbi <balbi@ti.com>
Cc: Matthijs van Duin <matthijsvanduin@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

The Armada 385 AP board has a USB3 port exposed that uses a GPIO to drive the
VBUS line. Enable the needed drivers to support this.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>

Now that we have EXTCON_USB_GPIO queued for v4.1, revert
commit addfcde7 ("ARM: dts: dra7x-evm: beagle-x15: Fix USB Host")

On these EVMs, the USB cable state has to be determined via the
ID pin tied to a GPIO line. We use the gpio-usb-extcon driver
to read the ID pin and the extcon framework to forward
the USB cable state information to the USB driver so the
controller can be configured in the right mode (host/peripheral).

Gets USB peripheral mode to work on this EVM.
Reviewed-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>

The Armada 380 and 385 SoCs have a Cortex-A9 CPU, so the PMU is available
to be used. This commit enables it in the devicetree.
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>

The Armada 375 SoC has a Cortex-A9 CPU, and so the PMU is available
to be used. This commit enables it in the devicetree.
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>

The Armada 370 and XP SoCs have Cortex-A9 compatible CPUs, and with a
Performance Monitoring Unit.

Enable it so that we can have hardware-assisted perf support.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>

AM57xx does not have ATL block integrated.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Remove the 'ti,timer-dsp' and 'ti,timer-pwm' properties from the timer
nodes that still have them. This seems to be copied from OMAP5, on
which only certain timers are capable of providing PWM functionality
or be able to interrupt the DSP. All the GPTimers On DRA7 are capable
of PWM and interrupting any core (due to the presence of Crossbar).

These properties were used by the driver to add capabilities to each
timer, and support requesting timers by capability. In the DT world,
we expect any users of timers to use phandles to the respective timer,
and use the omap_dm_timer_request_by_node() API. The API to request
using capabilities, omap_dm_timer_request_by_cap() API should be
deprecated eventually.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

ti,codec property is not used in omap-twl4030 driver in linux kernel but
we keep it as optional property, so that the existing dtbs do not
become noncompliant after the change on other OS.
Signed-off-by: Marek Belisko <marek@goldelico.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>