Do not nest m_rs_lock under c_lock

Disable interrupts in {rdma,atomic}_send_complete
Signed-off-by: Andy Grover <andy.grover@oracle.com>

Can no longer block, so use NOWAIT.
Signed-off-by: Andy Grover <andy.grover@oracle.com>

Now that rds_send_xmit() does not block, we can call it directly
instead of going through the helper thread.
Signed-off-by: Andy Grover <andy.grover@oracle.com>

rds_sendmsg() is calling the send worker function to
send the just-queued datagrams, presumably because it wants
the behavior where anything not sent will re-call the send
worker. We now ensure all queued datagrams are sent by retrying
from the send completion handler, so this isn't needed any more.
Signed-off-by: Andy Grover <andy.grover@oracle.com>

rds_message_put() cannot be called with irqs off, so move it after
irqs are re-enabled.

Spinlocks throughout the function do not to use _irqsave because
the lock of c_send_lock at top already disabled irqs.
Signed-off-by: Andy Grover <andy.grover@oracle.com>

This change allows us to call rds_send_xmit() from a tasklet,
which is crucial to our new operating model.

* Change c_send_lock to a spinlock
* Update stats fields "sem_" to "_lock"
* Remove unneeded rds_conn_is_sending()

About locking between shutdown and send -- send checks if the
connection is up. Shutdown puts the connection into
DISCONNECTING. After this, all threads entering send will exit
immediately. However, a thread could be *in* send_xmit(), so
shutdown acquires the c_send_lock to ensure everyone is out
before proceeding with connection shutdown.
Signed-off-by: Andy Grover <andy.grover@oracle.com>

Performance is better if we use allocations that don't block
to refill the receive ring. Since the whole reason we were
kicking out to the worker thread was so we could do blocking
allocs, we no longer need to do this.

Remove gfp params from rds_ib_recv_refill(); we always use
GFP_NOWAIT.
Signed-off-by: Andy Grover <andy.grover@oracle.com>

We now ask the transport to give us a rm for the congestion
map, and then we handle it normally. Previously, the
transport defined a function that we would call to send
a congestion map.

Convert TCP and loop transports to new cong map method.
Signed-off-by: Andy Grover <andy.grover@oracle.com>

Now that we are signaling send completions much less, we are likely
to have dirty entries in the send queue when the connection is
shut down (on rmmod, for example.) These are cleaned up a little
further down in conn_shutdown, but if we wait on the ring_empty_wait
for them, it'll never happen, and we hand on unload.
Signed-off-by: Andy Grover <andy.grover@oracle.com>

Previously, RDS would wait until the final send WR had completed
and then handle cleanup. With silent ops, we do not know
if an atomic, rdma, or data op will be last. This patch
handles any of these cases by keeping a pointer to the last
op in the message in m_last_op.

When the TX completion event fires, rds dispatches to per-op-type
cleanup functions, and then does whole-message cleanup, if the
last op equalled m_last_op.

This patch also moves towards having op-specific functions take
the op struct, instead of the overall rm struct.

rds_ib_connection has a pointer to keep track of a a partially-
completed data send operation. This patch changes it from an
rds_message pointer to the narrower rm_data_op pointer, and
modifies places that use this pointer as needed.
Signed-off-by: Andy Grover <andy.grover@oracle.com>

It hasn't cropped up in the field, but this code ensures it is
impossible to issue operations that pass an rdma cookie (DEST, MAP)
in the same sendmsg call that's actually initiating rdma or atomic
ops.

Disallowing this perverse-but-technically-allowed usage makes silent
RDMA heuristics slightly easier.
Signed-off-by: Andy Grover <andy.grover@oracle.com>

Add a flag to the API so users can indicate they want
silent operations. This is needed because silent ops
cannot be used with USE_ONCE MRs, so we can't just
assume silent.

Also, change send_xmit to do atomic op before rdma op if
both are present, and centralize the hairy logic to determine if
we want to attempt silent, or not.
Signed-off-by: Andy Grover <andy.grover@oracle.com>

Also, add a comment.
Signed-off-by: Andy Grover <andy.grover@oracle.com>

When dropping ops in the send queue, we notify the client
of failed rdma ops they asked for notifications on, but not
atomic ops. It should be for both.
Signed-off-by: Andy Grover <andy.grover@oracle.com>

rds_message_alloc_sgs() only works when nents is nonzero.
Signed-off-by: Andy Grover <andy.grover@oracle.com>

Do not allocate sgs for data for 0-length datagrams

Set data.op_active in rds_sendmsg() instead of
rds_message_copy_from_user().
Signed-off-by: Andy Grover <andy.grover@oracle.com>

Simplify rds_send_xmit().

Send a congestion map (via xmit_cong_map) without
decrementing send_quota.

Move resetting of conn xmit variables to end of loop.

Update comments.

Implement a special case to turn off sending an rds header
when there is an atomic op and no other data.
Signed-off-by: Andy Grover <andy.grover@oracle.com>

For consistency.
Signed-off-by: Andy Grover <andy.grover@oracle.com>

A big changeset, but it's all pretty dumb.

struct rds_rdma_op was already embedded in struct rm_rdma_op.
Remove rds_rdma_op and put its members in rm_rdma_op. Rename
members with "op_" prefix instead of "r_", for consistency.

Of course this breaks a lot, so fixup the code accordingly.
Signed-off-by: Andy Grover <andy.grover@oracle.com>

Add atomic_free_op function, analogous to rdma_free_op,
and call it in rds_message_purge().
Signed-off-by: Andy Grover <andy.grover@oracle.com>

cmsg_rdma_args just calls rdma_prepare and does a little
arg checking -- not quite enough to justify its existence.
Plus, it is the only caller of rdma_prepare().
Signed-off-by: Andy Grover <andy.grover@oracle.com>

Signed-off-by: Andy Grover <andy.grover@oracle.com>

Also, try to better-document the locking around the
rm and its m_inc in loop.c.
Signed-off-by: Andy Grover <andy.grover@oracle.com>

Maybe things worked fine with the flow control code running
even in the non-flow-control case, but making it explicitly
conditional helps the non-fc case be easier to read.
Signed-off-by: Andy Grover <andy.grover@oracle.com>

Removed unsignaled_bytes sysctl and code to signal
based on it. I believe unsignaled_wrs is more than
sufficient for our purposes.
Signed-off-by: Andy Grover <andy.grover@oracle.com>

Now that the header always goes first, it is possible to
simplify rds_ib_xmit. Instead of having a path to handle 0-byte
dgrams and another path to handle >0, these can both be handled
in one path. This lets us eliminate xmit_populate_wr().

Rename sent to bytes_sent, to differentiate better from other
variable named "send".
Signed-off-by: Andy Grover <andy.grover@oracle.com>

These functions were to cope with differently ordered
sg entries depending on RDS 3.0 or 3.1+. Now that
we've dropped 3.0 compatibility we no longer need them.

Also, modify usage sites for these to refer to sge[0] or [1]
directly. Reorder code to initialize header sgs first.
Signed-off-by: Andy Grover <andy.grover@oracle.com>

Signed-off-by: Andy Grover <andy.grover@oracle.com>

RDS 3.0 connections (in OFED 1.3 and earlier) put the
header at the end. 3.1 connections put it at the head.
The code has significant added complexity in order to
handle both configurations. In OFED 1.6 we can
drop this and simplify the code by only supporting
"header-first" configuration.

This patch checks the protocol version, and if prior
to 3.1, does not complete the connection.
Signed-off-by: Andy Grover <andy.grover@oracle.com>

both atomics and rdmas need to convert ib-specific completion codes
into RDS status codes. Rename rds_ib_rdma_send_complete to
rds_ib_send_complete, and have it take a pointer to the function to
call with the new error code.
Signed-off-by: Andy Grover <andy.grover@oracle.com>

Signed-off-by: Andy Grover <andy.grover@oracle.com>

Tidy up some whitespace issues.
Signed-off-by: Andy Grover <andy.grover@oracle.com>

This does not appear to be necessary.
Signed-off-by: Andy Grover <andy.grover@oracle.com>

Instead of using a constant for initiator_depth and
responder_resources, read the per-QP values when the
device is enumerated, and then use these values when creating
the connection.
Signed-off-by: Andy Grover <andy.grover@oracle.com>

Implement a CMSG-based interface to do FADD and CSWP ops.

Alter send routines to handle atomic ops.

Add atomic counters to stats.

Add xmit_atomic() to struct rds_transport

Inline rds_ib_send_unmap_rdma into unmap_rm
Signed-off-by: Andy Grover <andy.grover@oracle.com>

The previous code was correct, but made the assumption that
if r_notifier was non-NULL then either r_recverr or r_notify
was true. Valid, but fragile. Changed to explicitly check
r_recverr (shows up in greps for recverr now, too.)
Signed-off-by: Andy Grover <andy.grover@oracle.com>

rds_message_alloc_sgs() now returns correctly-initialized
sg lists, so calleds need not do this themselves.
Signed-off-by: Andy Grover <andy.grover@oracle.com>

This eliminates a separate memory alloc, although
it is now necessary to add an "r_active" flag, since
it is no longer to use the m_rdma_op pointer as an
indicator of if an rdma op is present.

rdma SGs allocated from rm sg pool.

rds_rm_size also gets bigger. It's a little inefficient to
run through CMSGs twice, but it makes later steps a lot smoother.
Signed-off-by: Andy Grover <andy.grover@oracle.com>

RDMA is now an intrinsic part of RDS, so it's easier to just have
a single header.
Signed-off-by: Andy Grover <andy.grover@oracle.com>

r_m_copy_from_user used to allocate the rm as well as kernel
buffers for the data, and then copy the data in. Now, sendmsg()
allocates the rm, although the data buffer alloc still happens
in r_m_copy_from_user.

SGs are still allocated with rm, but now r_m_alloc_sgs() is
used to reserve them. This allows multiple SG lists to be
allocated from the one rm -- this is important once we also
want to alloc our rdma sgl from this pool.
Signed-off-by: Andy Grover <andy.grover@oracle.com>