- 18 Feb, 2013 11 commits
-
-
Emmanuel Grumbach authored
I removed a bit too much info last time. Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
-
Eytan Lifshitz authored
Theoretically, the card may not enter CTKILL: In case the timer that iwl_prepare_ct_kill_task is setting, will expire before tt->state revert to its previous state. Signed-off-by: Eytan Lifshitz <eytan.lifshitz@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
-
Ilan Peer authored
Signed-off-by: Ilan Peer <ilan.peer@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
-
Ilan Peer authored
The time event data structures are required also for P2P Device interface. Signed-off-by: Ilan Peer <ilan.peer@intel.com> Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
-
Ilan Peer authored
The FW can differentiate between scans, according to the interface type on which the scan was issues. Supply the interfaces type information to the FW. Signed-off-by: Ilan Peer <ilan.peer@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
-
Johannes Berg authored
Occasionally, we would run into this warning: iwlwifi 0000:02:00.0: U iwl_mvm_protect_session extend 0x2601: only 200 ms left iwlwifi 0000:02:00.0: U iwl_mvm_remove_time_event Removing TE 0x2601 iwlwifi 0000:02:00.0: I iwl_pcie_enqueue_hcmd Sending command TIME_EVENT_CMD (#29), seq: 0x0925, 60 bytes at 37[5]:9 iwlwifi 0000:02:00.0: U iwl_pcie_send_hcmd_sync Attempting to send sync command TIME_EVENT_CMD iwlwifi 0000:02:00.0: U iwl_pcie_send_hcmd_sync Setting HCMD_ACTIVE for command TIME_EVENT_CMD iwlwifi 0000:02:00.0: I iwl_pcie_enqueue_hcmd Sending command TIME_EVENT_CMD (#29), seq: 0x0926, 60 bytes at 38[6]:9 iwlwifi 0000:02:00.0: U iwl_mvm_time_event_response TIME_EVENT_CMD response - UID = 0x2601 iwlwifi 0000:02:00.0: I iwl_pcie_hcmd_complete Clearing HCMD_ACTIVE for command TIME_EVENT_CMD iwlwifi 0000:02:00.0: U iwl_mvm_rx_time_event_notif Time event notification - UID = 0x2701 action 1 wlan0: associate with 00:0a:b8:55:a8:30 (try 2/3) ------------[ cut here ]------------ WARNING: at drivers/net/wireless/iwlwifi/mvm/time-event.c:269 iwl_mvm_time_event_send_add+0x163/0x1a0 [iwlmvm]() Modules linked in: [...] Call Trace: [<c1046e42>] warn_slowpath_common+0x72/0xa0 [<c1046e92>] warn_slowpath_null+0x22/0x30 [<f8cad913>] iwl_mvm_time_event_send_add+0x163/0x1a0 [iwlmvm] [<f8cadead>] iwl_mvm_protect_session+0xcd/0x1c0 [iwlmvm] [<f8ca2087>] iwl_mvm_mac_mgd_prepare_tx+0x67/0xa0 [iwlmvm] [<f882a130>] ieee80211_sta_work+0x8f0/0x1070 [mac80211] The reason is a problem with asynchronous vs. synchronous commands, what happens here is the following: * TE 0x2601 is removed, the TIME_EVENT_CMD for that is async * a new TE (will be 0x2701) is created, the TIME_EVENT_CMD for that is sync and also uses a notification wait for the response (to avoid another race condition) * the response for the TE 0x2601 removal comes from the firmware, and is handled by the notification wait handler that's really waiting for the second response, but can't tell the difference, we therefore see the message "TIME_EVENT_CMD response - UID = 0x2601" instead of "TIME_EVENT_CMD response - UID = 0x2701". Fix this issue by making the TE removal synchronous as well, this means that we wait for the response to that command first, before there's any chance of sending a new one. Also, to detect such issues more easily in the future, add a warning to the notification handler that detects them. Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
-
Johannes Berg authored
This is helpful for debugging the time event warning, but also in general to see what's going on. Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
-
Johannes Berg authored
All station commands must include a valid MAC ID, the ID 0 is randomly valid in some cases, but we must set the ID properly. Do that by passing the right station and using its mac_id_n_color. Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
-
Johannes Berg authored
For the firmware to know when DTIM beacons arrive we have to program the DTIM time in TSF and system time in the MAC context. Since mac80211 now tracks the different times (on demand), this becomes easy. Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
-
Johannes Berg authored
The iwlwifi-next tree removed IEEE80211_HW_NEED_DTIM_BEFORE_ASSOC while the mac80211-next tree removed Signed-off-by: Johannes Berg <johannes.berg@intel.com>
-
Johannes Berg authored
-
- 15 Feb, 2013 29 commits
-
-
-
Karl Beldan authored
Otherwise memory corruption occurs when using channel contexts (ATM when param 'channel' > 1). Signed-off-by: Karl Beldan <karl.beldan@rivierawaves.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
-
Johannes Berg authored
Even when connecting to an AP that doesn't support VHT, and even when the local device doesn't support it either, the downgrade message gets printed. Suppress the message if HT and/or VHT is disabled. Signed-off-by: Johannes Berg <johannes.berg@intel.com>
-
Johannes Berg authored
Adding the flag to mac80211 already without testing was clearly a mistake, one that we now pay for by having to reserve bit 13 forever. The problem is cfg80211 doesn't allow capability/rate changes for station entries that were added unassociated, so the station entries cannot be set up properly when marked associated. Change the NL80211_FEATURE_FULL_AP_CLIENT_STATE value to make it clear to userspace implementations that all current kernels don't actually support it, even though the previous bit is set, and of course also remove the flag from mac80211 until we test and fix the issues. Signed-off-by: Johannes Berg <johannes.berg@intel.com>
-
Jouni Malinen authored
The information of the peer's capabilities is required for the driver to perform TDLS Peer UAPSD operations. This information of the peer is passed by the supplicant using NL80211_CMD_SET_STATION command. This commit enhances the function nl80211_set_station to pass this information of the peer to the driver in case this command is used with the TDLS peer STA. In addition, make the HT/VHT capability configuration handled more consistently for other STA cases (reject both instead of just HT). Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
-
Jouni Malinen authored
The information of the peer's capabilities and extended capabilities are required for the driver to perform TDLS Peer UAPSD operations and off channel operations. This information of the peer is passed from user space using NL80211_CMD_SET_STATION command. This commit enhances the function nl80211_set_station to pass the capability information of the peer to the driver. Similarly, there may be need for capability information for other modes, so allow this to be provided with both add_station and change_station. Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
-
Johannes Berg authored
Use the new extended capabilities advertising to advertise the fact that operating mode notification is supported. Signed-off-by: Johannes Berg <johannes.berg@intel.com>
-
Johannes Berg authored
In many cases, userspace may need to know which of the 802.11 extended capabilities ("Extended Capabilities element") are implemented in the driver or device, to include them e.g. in beacons, assoc request/response or other frames. Add a new nl80211 attribute to hold the extended capabilities bitmap for this. Signed-off-by: Johannes Berg <johannes.berg@intel.com>
-
Johannes Berg authored
Instead of modifying the HT SMPS capability field for stations, track the SMPS mode explicitly in a new field in the station struct and use it in the drivers that care about it. This simplifies the code using it. Signed-off-by: Johannes Berg <johannes.berg@intel.com>
-
Thomas Pedersen authored
Mesh interfaces will now respond to any broadcast (or matching directed mesh) probe requests with a probe response. Signed-off-by: Thomas Pedersen <thomas@cozybit.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
-
Thomas Pedersen authored
Previously, the entire mesh beacon would be generated each time the beacon timer fired. Instead generate a beacon head and tail (so the TIM can easily be inserted when mesh power save is on) when starting a mesh or the MBSS parameters change. Also add a mutex for protecting beacon updates and preventing leaks. Signed-off-by: Thomas Pedersen <thomas@cozybit.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
-
Johannes Berg authored
Make all the parsed IE pointers const, and propagate the change to all the users etc. Signed-off-by: Johannes Berg <johannes.berg@intel.com>
-
Johannes Berg authored
When drivers or regulatory have limitations on 40, 80 or 160 MHz channels, advertise these to userspace via nl80211. Also add a new feature flag to let userspace know this is supported. Signed-off-by: Johannes Berg <johannes.berg@intel.com>
-
Johannes Berg authored
Some drivers might support 80 or 160 MHz only on some channels for whatever reason, so allow them to disable these channel widths. Also maintain the new flags when regulatory bandwidth limitations would disable these wide channels. Reviewed-by: Luis R. Rodriguez <mcgrof@do-not-panic.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
-
Johannes Berg authored
A while ago, I made the mac80211 station code never change the channel type after association. This solved a number of issues but is ultimately wrong, we should react if the AP changes the HT operation IE and switches bandwidth. One of the issues is that we associate as HT40 capable, but if the AP ever switches to 40 MHz we won't be able to receive such frames because we never set our channel to 40 MHz. This addresses this and VHT operation changes. If there's a change that is incompatible with our setup, e.g. if the AP decides to change the channel entirely (and for some reason we still hear the beacon) we'll just disconnect. Signed-off-by: Johannes Berg <johannes.berg@intel.com>
-
Johannes Berg authored
The next patch will need it further up in the file, so move it unchanged now. Signed-off-by: Johannes Berg <johannes.berg@intel.com>
-
Johannes Berg authored
For HT and VHT the current bandwidth can change, add the function ieee80211_vif_change_bandwidth() to take care of this. It returns a failure if the new bandwidth isn't compatible with the existing channel context, the caller has to handle that. When it happens, also inform the driver that the bandwidth changed for this virtual interface (no drivers would actually care today though.) Changing to/from HT/VHT isn't allowed though. Signed-off-by: Johannes Berg <johannes.berg@intel.com>
-
Johannes Berg authored
The channel use is confusing, some uses the channel context and some the bss_conf.chandef. The latter is fine, so get rid of the channel context part. Signed-off-by: Johannes Berg <johannes.berg@intel.com>
-
Johannes Berg authored
Having HT/VHT operation IEs but not capability IEs leads to a strange situation where we configure the channel to an HT or VHT bandwidth and then can't actually use it. Prevent this by checking that the HT and VHT capability IEs are present as well as the operation IEs; if not, disable HT and/or VHT. Signed-off-by: Johannes Berg <johannes.berg@intel.com>
-
Johannes Berg authored
In beacons and association response frames an AP may include an operating mode notification element to advertise changes in the number of spatial streams it can receive. Handle this using the existing function that handles the action frame, but only handle NSS changes, not bandwidth changes which aren't allowed here. Signed-off-by: Johannes Berg <johannes.berg@intel.com>
-
Johannes Berg authored
This should be called ieee80211_change_chanctx() since it changes the channel context, not a chandef. Signed-off-by: Johannes Berg <johannes.berg@intel.com>
-
Johannes Berg authored
The code to disable HT and VHT if VHT was advertised without VHT is wrong -- it accidentally uses the wrong flags. Fix that. Signed-off-by: Johannes Berg <johannes.berg@intel.com>
-
Johannes Berg authored
In case of connection, the station data is initialised from the beacon/probe response first and then updated from the association response. If the latter is different we update the rate control algorithm and driver. Instead of doing it this way, set the station data properly with data from the association response before initializing rate control. Also simplify the code by passing the station pointer. Signed-off-by: Johannes Berg <johannes.berg@intel.com>
-
Johannes Berg authored
Handle the operating mode notification action frame. When the supported streams or the bandwidth change let the driver and rate control algorithm know. Signed-off-by: Johannes Berg <johannes.berg@intel.com>
-
Johannes Berg authored
With VHT, a station can change the number of spatial streams it can receive on the fly, not unlike spatial multiplexing in HT. Prepare for that by tracking the maximum number of spatial streams it can receive when the connection is established. Signed-off-by: Johannes Berg <johannes.berg@intel.com>
-
Johannes Berg authored
Define the action frame format, the VHT category and its action types and the field format and EID for operating mode notifications. The frame may be used outside of VHT context as well, so don't include "VHT" in the names. Signed-off-by: Johannes Berg <johannes.berg@intel.com>
-
Johannes Berg authored
For VHT, many more bandwidth changes are possible. As a first step, stop toggling the IEEE80211_HT_CAP_SUP_WIDTH_20_40 flag in the HT capabilities and instead introduce a bandwidth field indicating the currently usable bandwidth to transmit to the station. Of course, make all drivers use it. To achieve this, make ieee80211_ht_cap_ie_to_sta_ht_cap() get the station as an argument, rather than the new capabilities, so it can set up the new bandwidth field. If the station is a VHT station and VHT bandwidth is in use, also set the bandwidth accordingly. Doing this allows us to get rid of the supports_40mhz flag as the HT capabilities now reflect the true capability instead of the current setting. While at it, also fix ieee80211_ht_cap_ie_to_sta_ht_cap() to not ignore HT cap overrides when MCS TX isn't supported (not that it really happens...) Signed-off-by: Johannes Berg <johannes.berg@intel.com>
-
Johannes Berg authored
Like with HT, make things a bit simpler in future patches by passing the station to ieee80211_vht_cap_ie_to_sta_vht_cap() instead of the vht_cap pointer. Also disable VHT here if HT isn't supported. Signed-off-by: Johannes Berg <johannes.berg@intel.com>
-