swapper_low_pmd_dir and swapper_pud_dir are actually completely
useless and unnecessary.

We just need swapper_pg_dir[].  Naturally the other page table chunks
will be allocated on an as-needed basis.  Since the kernel actually
accesses these tables in the PAGE_OFFSET view, there is not even a TLB
locality advantage of placing them in the kernel image.

Use the hard coded vmlinux.ld.S slot for swapper_pg_dir which is
naturally page aligned.

Increase MAX_BANKS to 1024 in order to handle heavily fragmented
virtual guests.

Even with this MAX_BANKS increase, the kernel is 20K+ smaller.
Signed-off-by: David S. Miller <davem@davemloft.net>
Acked-by: Bob Picco <bob.picco@oracle.com>

This patch attempts to do a few things. The highlights are: 1) enable
SPARSE_IRQ unconditionally, 2) kills off !SPARSE_IRQ code 3) allocates
ivector_table at boot time and 4) default to cookie only VIRQ mechanism
for supported firmware. The first firmware with cookie only support for
me appears on T5. You can optionally force the HV firmware to not cookie
only mode which is the sysino support.

The sysino is a deprecated HV mechanism according to the most recent
SPARC Virtual Machine Specification. HV_GRP_INTR is what controls the
cookie/sysino firmware versioning.

The history of this interface is:

1) Major version 1.0 only supported sysino based interrupt interfaces.

2) Major version 2.0 added cookie based VIRQs, however due to the fact
   that OSs were using the VIRQs without negoatiating major version
   2.0 (Linux and Solaris are both guilty), the VIRQs calls were
   allowed even with major version 1.0

   To complicate things even further, the VIRQ interfaces were only
   actually hooked up in the hypervisor for LDC interrupt sources.
   VIRQ calls on other device types would result in HV_EINVAL errors.

   So effectively, major version 2.0 is unusable.

3) Major version 3.0 was created to signal use of VIRQs and the fact
   that the hypervisor has these calls hooked up for all interrupt
   sources, not just those for LDC devices.

A new boot option is provided should cookie only HV support have issues.
hvirq - this is the version for HV_GRP_INTR. This is related to HV API
versioning.  The code attempts major=3 first by default. The option can
be used to override this default.

I've tested with SPARSE_IRQ on T5-8, M7-4 and T4-X and Jalap?no.
Signed-off-by: Bob Picco <bob.picco@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In order to accomodate embedded per-cpu allocation with large numbers
of cpus and numa nodes, we have to use as much virtual address space
as possible for the vmalloc region.  Otherwise we can get things like:

PERCPU: max_distance=0x380001c10000 too large for vmalloc space 0xff00000000

So, once we select a value for PAGE_OFFSET, derive the size of the
vmalloc region based upon that.
Signed-off-by: David S. Miller <davem@davemloft.net>
Acked-by: Bob Picco <bob.picco@oracle.com>

Make sure, at compile time, that the kernel can properly support
whatever MAX_PHYS_ADDRESS_BITS is defined to.

On M7 chips, use a max_phys_bits value of 49.

Based upon a patch by Bob Picco.
Signed-off-by: David S. Miller <davem@davemloft.net>
Acked-by: Bob Picco <bob.picco@oracle.com>

For sparse memory configurations, the vmemmap array behaves terribly
and it takes up an inordinate amount of space in the BSS section of
the kernel image unconditionally.

Just build huge PMDs and look them up just like we do for TLB misses
in the vmalloc area.

Kernel BSS shrinks by about 2MB.
Signed-off-by: David S. Miller <davem@davemloft.net>
Acked-by: Bob Picco <bob.picco@oracle.com>

If max_phys_bits needs to be > 43 (f.e. for T4 chips), things like
DEBUG_PAGEALLOC stop working because the 3-level page tables only
can cover up to 43 bits.

Another problem is that when we increased MAX_PHYS_ADDRESS_BITS up to
47, several statically allocated tables became enormous.

Compounding this is that we will need to support up to 49 bits of
physical addressing for M7 chips.

The two tables in question are sparc64_valid_addr_bitmap and
kpte_linear_bitmap.

The first holds a bitmap, with 1 bit for each 4MB chunk of physical
memory, indicating whether that chunk actually exists in the machine
and is valid.

The second table is a set of 2-bit values which tell how large of a
mapping (4MB, 256MB, 2GB, 16GB, respectively) we can use at each 256MB
chunk of ram in the system.

These tables are huge and take up an enormous amount of the BSS
section of the sparc64 kernel image.  Specifically, the
sparc64_valid_addr_bitmap is 4MB, and the kpte_linear_bitmap is 128K.

So let's solve the space wastage and the DEBUG_PAGEALLOC problem
at the same time, by using the kernel page tables (as designed) to
manage this information.

We have to keep using large mappings when DEBUG_PAGEALLOC is disabled,
and we do this by encoding huge PMDs and PUDs.

On a T4-2 with 256GB of ram the kernel page table takes up 16K with
DEBUG_PAGEALLOC disabled and 256MB with it enabled.  Furthermore, this
memory is dynamically allocated at run time rather than coded
statically into the kernel image.
Signed-off-by: David S. Miller <davem@davemloft.net>
Acked-by: Bob Picco <bob.picco@oracle.com>

As currently coded the KTSB accesses in the kernel only support up to
47 bits of physical addressing.

Adjust the instruction and patching sequence in order to support
arbitrary 64 bits addresses.
Signed-off-by: David S. Miller <davem@davemloft.net>
Acked-by: Bob Picco <bob.picco@oracle.com>

Now that we use 4-level page tables, we can provide up to 53-bits of
virtual address space to the user.

Adjust the VA hole based upon the capabilities of the cpu type probed.
Signed-off-by: David S. Miller <davem@davemloft.net>
Acked-by: Bob Picco <bob.picco@oracle.com>

This has become necessary with chips that support more than 43-bits
of physical addressing.

Based almost entirely upon a patch by Bob Picco.
Signed-off-by: David S. Miller <davem@davemloft.net>
Acked-by: Bob Picco <bob.picco@oracle.com>

When we have to split up a flush request into multiple pieces
(in order to avoid the firmware range) we don't specify the
arguments in the right order for the second piece.

Fix the order, or else we get hangs as the code tries to
flush "a lot" of entries and we get lockups like this:

[ 4422.981276] NMI watchdog: BUG: soft lockup - CPU#12 stuck for 23s! [expect:117032]
[ 4422.996130] Modules linked in: ipv6 loop usb_storage igb ptp sg sr_mod ehci_pci ehci_hcd pps_core n2_rng rng_core
[ 4423.016617] CPU: 12 PID: 117032 Comm: expect Not tainted 3.17.0-rc4+ #1608
[ 4423.030331] task: fff8003cc730e220 ti: fff8003d99d54000 task.ti: fff8003d99d54000
[ 4423.045282] TSTATE: 0000000011001602 TPC: 00000000004521e8 TNPC: 00000000004521ec Y: 00000000    Not tainted
[ 4423.064905] TPC: <__flush_tlb_kernel_range+0x28/0x40>
[ 4423.074964] g0: 000000000052fd10 g1: 00000001295a8000 g2: ffffff7176ffc000 g3: 0000000000002000
[ 4423.092324] g4: fff8003cc730e220 g5: fff8003dfedcc000 g6: fff8003d99d54000 g7: 0000000000000006
[ 4423.109687] o0: 0000000000000000 o1: 0000000000000000 o2: 0000000000000003 o3: 00000000f0000000
[ 4423.127058] o4: 0000000000000080 o5: 00000001295a8000 sp: fff8003d99d56d01 ret_pc: 000000000052ff54
[ 4423.145121] RPC: <__purge_vmap_area_lazy+0x314/0x3a0>
[ 4423.155185] l0: 0000000000000000 l1: 0000000000000000 l2: 0000000000a38040 l3: 0000000000000000
[ 4423.172559] l4: fff8003dae8965e0 l5: ffffffffffffffff l6: 0000000000000000 l7: 00000000f7e2b138
[ 4423.189913] i0: fff8003d99d576a0 i1: fff8003d99d576a8 i2: fff8003d99d575e8 i3: 0000000000000000
[ 4423.207284] i4: 0000000000008008 i5: fff8003d99d575c8 i6: fff8003d99d56df1 i7: 0000000000530c24
[ 4423.224640] I7: <free_vmap_area_noflush+0x64/0x80>
[ 4423.234193] Call Trace:
[ 4423.239051]  [0000000000530c24] free_vmap_area_noflush+0x64/0x80
[ 4423.251029]  [0000000000531a7c] remove_vm_area+0x5c/0x80
[ 4423.261628]  [0000000000531b80] __vunmap+0x20/0x120
[ 4423.271352]  [000000000071cf18] n_tty_close+0x18/0x40
[ 4423.281423]  [00000000007222b0] tty_ldisc_close+0x30/0x60
[ 4423.292183]  [00000000007225a4] tty_ldisc_reinit+0x24/0xa0
[ 4423.303120]  [0000000000722ab4] tty_ldisc_hangup+0xd4/0x1e0
[ 4423.314232]  [0000000000719aa0] __tty_hangup+0x280/0x3c0
[ 4423.324835]  [0000000000724cb4] pty_close+0x134/0x1a0
[ 4423.334905]  [000000000071aa24] tty_release+0x104/0x500
[ 4423.345316]  [00000000005511d0] __fput+0x90/0x1e0
[ 4423.354701]  [000000000047fa54] task_work_run+0x94/0xe0
[ 4423.365126]  [0000000000404b44] __handle_signal+0xc/0x2c

Fixes: 4ca9a237 ("sparc64: Guard against flushing openfirmware mappings.")
Signed-off-by: David S. Miller <davem@davemloft.net>

The vio_set_intr() API should be used by VIO consumers to enable/disable
Rx interrupts to facilitate deferred processing in softirq/bottom-half
context.
Signed-off-by: Sowmini Varadhan <sowmini.varadhan@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

vio_dring_avail() will allow use of every dring entry, but when the last
entry is allocated then dr->prod == dr->cons which is indistinguishable from
the ring empty condition. This causes the next allocation to reuse an entry.
When this happens in sunvdc, the server side vds driver begins nack'ing the
messages and ends up resetting the ldc channel. This problem does not effect
sunvnet since it checks for < 2.

The fix here is to just never allocate the very last dring slot so that full
and empty are not the same condition. The request start path was changed to
check for the ring being full a bit earlier, and to stop the blk_queue if
there is no space left. The blk_queue will be restarted once the ring is
only half full again. The number of ring entries was increased to 512 which
matches the sunvnet and Solaris vdc drivers, and greatly reduces the
frequency of hitting the ring full condition and the associated blk_queue
stop/starting. The checks in sunvent were adjusted to account for
vio_dring_avail() returning 1 less.

Orabug: 19441666
OraBZ: 14983
Signed-off-by: Dwight Engen <dwight.engen@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

ldc_map_sg() could fail its check that the number of pages referred to
by the sg scatterlist was <= the number of cookies.

This fixes the issue by doing a similar thing to the xen-blkfront driver,
ensuring that the scatterlist will only ever contain a segment count <=
port->ring_cookies, and each segment will be page aligned, and <= page
size. This ensures that the scatterlist is always mappable.

Orabug: 19347817
OraBZ: 15945
Signed-off-by: Dwight Engen <dwight.engen@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The LDom diskserver doesn't return reliable geometry data. In addition,
the types for all fields in the vio_disk_geom are u16, which were being
truncated in the cast into the u8's of the Linux struct hd_geometry.

Modify vdc_getgeo() to compute the geometry from the disk's capacity in a
manner consistent with xen-blkfront::blkif_getgeo().
Signed-off-by: Dwight Engen <dwight.engen@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Interpret the media type from v1.1 protocol to support CDROM/DVD.

For v1.0 protocol, a disk's size continues to be calculated from the
geometry returned by the vdisk server. The geometry returned by the server
can be less than the actual number of sectors available in the backing
image/device due to the rounding in the division used to compute the
geometry in the vdisk server.

In v1.1 protocol a disk's actual size in sectors is returned during the
handshake. Use this size when v1.1 protocol is negotiated. Since this size
will always be larger than the former geometry computed size, disks created
under v1.0 will be forwards compatible to v1.1, but not vice versa.
Signed-off-by: Dwight Engen <dwight.engen@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add VIO protocol version 1.6 interfaces.
Signed-off-by: David L Stevens <david.stevens@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

We changed PAGE_OFFSET to be a variable rather than a constant,
but this reference here in the hibernate assembler got missed.
Signed-off-by: David S. Miller <davem@davemloft.net>

The request_irq() needs to be done from ldc_alloc()
to avoid the following (caught by lockdep)

 [00000000004a0738] __might_sleep+0xf8/0x120
 [000000000058bea4] kmem_cache_alloc_trace+0x184/0x2c0
 [00000000004faf80] request_threaded_irq+0x80/0x160
 [000000000044f71c] ldc_bind+0x7c/0x220
 [0000000000452454] vio_port_up+0x54/0xe0
 [00000000101f6778] probe_disk+0x38/0x220 [sunvdc]
 [00000000101f6b8c] vdc_port_probe+0x22c/0x300 [sunvdc]
 [0000000000451a88] vio_device_probe+0x48/0x60
 [000000000074c56c] really_probe+0x6c/0x300
 [000000000074c83c] driver_probe_device+0x3c/0xa0
 [000000000074c92c] __driver_attach+0x8c/0xa0
 [000000000074a6ec] bus_for_each_dev+0x6c/0xa0
 [000000000074c1dc] driver_attach+0x1c/0x40
 [000000000074b0fc] bus_add_driver+0xbc/0x280
Signed-off-by: Sowmini Varadhan <sowmini.varadhan@oracle.com>
Acked-by: Dwight Engen <dwight.engen@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The T5 (niagara5) has different PCR related HV fast trap values and a new
HV API Group. This patch utilizes these and shares when possible with niagara4.

We use the same sparc_pmu niagara4_pmu. Should there be new effort to
obtain the MCU perf statistics then this would have to be changed.

Cc: sparclinux@vger.kernel.org
Signed-off-by: Bob Picco <bob.picco@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The "mem" boot option can result in many unexpected consequences. This patch
attempts to prevent boot hangs which have been experienced on T4-4 and T5-8.
Basically the boot loader allocates vmlinuz and initrd higher in available
OBP physical memory. For example, on a 2Tb T5-8 it isn't possible to boot
with mem=20G.

The patch utilizes memblock to avoid reserved regions and trim memory which
is only free. Other improvements are possible for a multi-node machine.

This is a snippet of the boot log with mem=20G on T5-8 with the patch applied:
MEMBLOCK configuration:	<- before memory reduction
 memory size = 0x1ffad6ce000 reserved size = 0xa1adf44
 memory.cnt  = 0xb
 memory[0x0]    [0x00000030400000-0x00003fdde47fff], 0x3fada48000 bytes
 memory[0x1]    [0x00003fdde4e000-0x00003fdde4ffff], 0x2000 bytes
 memory[0x2]    [0x00080000000000-0x00083fffffffff], 0x4000000000 bytes
 memory[0x3]    [0x00100000000000-0x00103fffffffff], 0x4000000000 bytes
 memory[0x4]    [0x00180000000000-0x00183fffffffff], 0x4000000000 bytes
 memory[0x5]    [0x00200000000000-0x00203fffffffff], 0x4000000000 bytes
 memory[0x6]    [0x00280000000000-0x00283fffffffff], 0x4000000000 bytes
 memory[0x7]    [0x00300000000000-0x00303fffffffff], 0x4000000000 bytes
 memory[0x8]    [0x00380000000000-0x00383fffc71fff], 0x3fffc72000 bytes
 memory[0x9]    [0x00383fffc92000-0x00383fffca1fff], 0x10000 bytes
 memory[0xa]    [0x00383fffcb4000-0x00383fffcb5fff], 0x2000 bytes
 reserved.cnt  = 0x2
 reserved[0x0]  [0x00380000000000-0x0038000117e7f8], 0x117e7f9 bytes
 reserved[0x1]  [0x00380004000000-0x0038000d02f74a], 0x902f74b bytes
...
MEMBLOCK configuration:	<- after reduction of memory
 memory size = 0x50a1adf44 reserved size = 0xa1adf44
 memory.cnt  = 0x4
 memory[0x0]    [0x00380000000000-0x0038000117e7f8], 0x117e7f9 bytes
 memory[0x1]    [0x00380004000000-0x0038050d01d74a], 0x50901d74b bytes
 memory[0x2]    [0x00383fffc92000-0x00383fffca1fff], 0x10000 bytes
 memory[0x3]    [0x00383fffcb4000-0x00383fffcb5fff], 0x2000 bytes
 reserved.cnt  = 0x2
 reserved[0x0]  [0x00380000000000-0x0038000117e7f8], 0x117e7f9 bytes
 reserved[0x1]  [0x00380004000000-0x0038000d02f74a], 0x902f74b bytes
...
Early memory node ranges
  node   7: [mem 0x380000000000-0x38000117dfff]
  node   7: [mem 0x380004000000-0x380f0d01bfff]
  node   7: [mem 0x383fffc92000-0x383fffca1fff]
  node   7: [mem 0x383fffcb4000-0x383fffcb5fff]
Could not find start_pfn for node 0
Could not find start_pfn for node 1
Could not find start_pfn for node 2
Could not find start_pfn for node 3
Could not find start_pfn for node 4
Could not find start_pfn for node 5
Could not find start_pfn for node 6
.

The patch was tested on T4-1, T5-8 and Jalap?no.

Cc: sparclinux@vger.kernel.org
Signed-off-by: Bob Picco <bob.picco@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

We have seen an issue with guest boot into LDOM that causes early boot failures
because of no matching rules for node identitity of the memory. I analyzed this
on my T4 and concluded there might not be a solution. I saw the issue in
mainline too when booting into the control/primary domain - with guests
configured.  Note, this could be a firmware bug on some older machines.

I'll provide a full explanation of the issues below. Should we not find a
matching BEST latency group for a real address (RA) then we will assume node 0.
On the T4-2 here with the information provided I can't see an alternative.

Technically the LDOM shown below should match the MBLOCK to the
favorable latency group. However other factors must be considered too. Were
the memory controllers configured "fine" grained interleave or "coarse"
grain interleaved -  T4. Also should a "group" MD node be considered a NUMA
node?

There has to be at least one Machine Description (MD) "group" and hence one
NUMA node. The group can have one or more latency groups (lg) - more than one
memory controller. The current code chooses the smallest latency as the most
favorable per group. The latency and lg information is in MLGROUP below.
MBLOCK is the base and size of the RAs for the machine as fetched from OBP
/memory "available" property. My machine has one MBLOCK but more would be
possible - with holes?

For a T4-2 the following information has been gathered:
with LDOM guest
MEMBLOCK configuration:
 memory size = 0x27f870000
 memory.cnt  = 0x3
 memory[0x0]    [0x00000020400000-0x0000029fc67fff], 0x27f868000 bytes
 memory[0x1]    [0x0000029fd8a000-0x0000029fd8bfff], 0x2000 bytes
 memory[0x2]    [0x0000029fd92000-0x0000029fd97fff], 0x6000 bytes
 reserved.cnt  = 0x2
 reserved[0x0]  [0x00000020800000-0x000000216c15c0], 0xec15c1 bytes
 reserved[0x1]  [0x00000024800000-0x0000002c180c1e], 0x7980c1f bytes
MBLOCK[0]: base[20000000] size[280000000] offset[0]
(note: "base" and "size" reported in "MBLOCK" encompass the "memory[X]" values)
(note: (RA + offset) & mask = val is the formula to detect a match for the
memory controller. should there be no match for find_node node, a return
value of -1 resulted for the node - BAD)

There is one group. It has these forward links
MLGROUP[1]: node[545] latency[1f7e8] match[200000000] mask[200000000]
MLGROUP[2]: node[54d] latency[2de60] match[0] mask[200000000]
NUMA NODE[0]: node[545] mask[200000000] val[200000000] (latency[1f7e8])
(note: "val" is the best lg's (smallest latency) "match")

no LDOM guest - bare metal
MEMBLOCK configuration:
 memory size = 0xfdf2d0000
 memory.cnt  = 0x3
 memory[0x0]    [0x00000020400000-0x00000fff6adfff], 0xfdf2ae000 bytes
 memory[0x1]    [0x00000fff6d2000-0x00000fff6e7fff], 0x16000 bytes
 memory[0x2]    [0x00000fff766000-0x00000fff771fff], 0xc000 bytes
 reserved.cnt  = 0x2
 reserved[0x0]  [0x00000020800000-0x00000021a04580], 0x1204581 bytes
 reserved[0x1]  [0x00000024800000-0x0000002c7d29fc], 0x7fd29fd bytes
MBLOCK[0]: base[20000000] size[fe0000000] offset[0]

there are two groups
group node[16d5]
MLGROUP[0]: node[1765] latency[1f7e8] match[0] mask[200000000]
MLGROUP[3]: node[177d] latency[2de60] match[200000000] mask[200000000]
NUMA NODE[0]: node[1765] mask[200000000] val[0] (latency[1f7e8])
group node[171d]
MLGROUP[2]: node[1775] latency[2de60] match[0] mask[200000000]
MLGROUP[1]: node[176d] latency[1f7e8] match[200000000] mask[200000000]
NUMA NODE[1]: node[176d] mask[200000000] val[200000000] (latency[1f7e8])
(note: for this two "group" bare metal machine, 1/2 memory is in group one's
lg and 1/2 memory is in group two's lg).

Cc: sparclinux@vger.kernel.org
Signed-off-by: Bob Picco <bob.picco@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

We've witnessed a few TLB events causing the machine to power off because
of prom_halt. In one case it was some nfs related area during rmmod. Another
was an mmapper of /dev/mem. A more recent one is an ITLB issue with
a bad pagesize which could be a hardware bug. Bugs happen but we should
attempt to not power off the machine and/or hang it when possible.

This is a DTLB error from an mmapper of /dev/mem:
[root@sparcie ~]# SUN4V-DTLB: Error at TPC[fffff80100903e6c], tl 1
SUN4V-DTLB: TPC<0xfffff80100903e6c>
SUN4V-DTLB: O7[fffff801081979d0]
SUN4V-DTLB: O7<0xfffff801081979d0>
SUN4V-DTLB: vaddr[fffff80100000000] ctx[1250] pte[98000000000f0610] error[2]
.

This is recent mainline for ITLB:
[ 3708.179864] SUN4V-ITLB: TPC<0xfffffc010071cefc>
[ 3708.188866] SUN4V-ITLB: O7[fffffc010071cee8]
[ 3708.197377] SUN4V-ITLB: O7<0xfffffc010071cee8>
[ 3708.206539] SUN4V-ITLB: vaddr[e0003] ctx[1a3c] pte[2900000dcc800eeb] error[4]
.

Normally sun4v_itlb_error_report() and sun4v_dtlb_error_report() would call
prom_halt() and drop us to OF command prompt "ok". This isn't the case for
LDOMs and the machine powers off.

For the HV reported error of HV_ENORADDR for HV HV_MMU_MAP_ADDR_TRAP we cause
a SIGBUS error by qualifying it within do_sparc64_fault() for fault code mask
of FAULT_CODE_BAD_RA. This is done when trap level (%tl) is less or equal
one("1"). Otherwise, for %tl > 1,  we proceed eventually to die_if_kernel().

The logic of this patch was partially inspired by David Miller's feedback.

Power off of large sparc64 machines is painful. Plus die_if_kernel provides
more context. A reset sequence isn't a brief period on large sparc64 but
better than power-off/power-on sequence.

Cc: sparclinux@vger.kernel.org
Signed-off-by: Bob Picco <bob.picco@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

dma_zalloc_coherent() calls dma_alloc_coherent(__GFP_ZERO)
but the sparc32 implementations sbus_alloc_coherent() and
pci32_alloc_coherent() doesn't take the gfp flags into
account.

Tested on the SPARC32/LEON GRETH Ethernet driver which fails
due to dma_alloc_coherent(__GFP_ZERO) returns non zeroed
pages.
Signed-off-by: Daniel Hellstrom <daniel@gaisler.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The leon_dma_ops struct is needed for leon regardless of PCI configuration.
Signed-off-by: Andreas Larsson <andreas@gaisler.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This makes sure that leon_cycles_offset takes the pending bit into
account and that leon_clear_clock_irq clears the pending bit. Otherwise,
if leon_cycles_offset is executed after the timer has wrapped but before
timer_interrupt has increased timer_cs_internal_counter, time can be
perceived to go backwards.
Signed-off-by: Andreas Larsson <andreas@gaisler.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This makes memset follow the standard (instead of returning 0 on success). This
is needed when certain versions of gcc optimizes around memset calls and assume
that the address argument is preserved in %o0.
Signed-off-by: Andreas Larsson <andreas@gaisler.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Allen Pais <allen.pais@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add M6 and M7 chip type in cpumap.c to correctly build CPU distribution map that spans all online CPUs.
Signed-off-by: Allen Pais <allen.pais@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The following patch adds support for correctly
recognising M6 and M7 cpu type.
Signed-off-by: Allen Pais <allen.pais@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Pull arch/microblaze fixes from Michal Simek:
 - Kconfig menu structure fix
 - fix number of syscalls
 - fix compilation warnings from allmodconfig

* tag 'microblaze-3.17-rc5' of git://git.monstr.eu/linux-2.6-microblaze:
  microblaze: Fix number of syscalls
  microblaze: Rename Advance setup to Kernel features
  microblaze: Add mm/Kconfig to advance menu
  arch/microblaze/include/asm/uaccess.h: Use pr_devel() instead of pr_debug()
  arch/microblaze/include/asm/entry.h: Include "linux/linkage.h" to avoid compiling issue

Number of syscalls have to be updated too.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>

"Advance setup: menu is misleading that's why rename it.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>

mm/Kconfig is getting too big to be in root menu.
Move it to submenu.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>

When DYNAMIC_DEBUG enabled, pr_debug() depends on KBUILD_MODNAME which
also depends on the modules number in Makefile. The related information
in "scripts/Makefile.lib" line 94:

  # $(modname_flags) #defines KBUILD_MODNAME as the name of the module it will
  # end up in (or would, if it gets compiled in)
  # Note: Files that end up in two or more modules are compiled without the
  #       KBUILD_MODNAME definition. The reason is that any made-up name would
  #       differ in different configs.

For this case, 'radio-si470x-i2c.o' and 'radio-si470x-common.o' are in
one line, so cause compiling issue. And 'uaccess.h' is a common shared
header (not specially for drivers), so use pr_devel() instead of is OK.

The related error with allmodconfig:

    CC [M]  drivers/media/radio/si470x/radio-si470x-i2c.o
    CC [M]  drivers/media/radio/si470x/radio-si470x-common.o
  In file included from include/linux/printk.h:257:0,
                   from include/linux/kernel.h:13,
                   from drivers/media/radio/si470x/radio-si470x.h:29,
                   from drivers/media/radio/si470x/radio-si470x-common.c:115:
  ./arch/microblaze/include/asm/uaccess.h: In function 'access_ok':
  include/linux/dynamic_debug.h:66:14: error: 'KBUILD_MODNAME' undeclared (first use in this function)
     .modname = KBUILD_MODNAME,   \
                ^
  include/linux/dynamic_debug.h:76:2: note: in expansion of macro 'DEFINE_DYNAMIC_DEBUG_METADATA'
    DEFINE_DYNAMIC_DEBUG_METADATA(descriptor, fmt);  \
    ^
  include/linux/printk.h:263:2: note: in expansion of macro 'dynamic_pr_debug'
    dynamic_pr_debug(fmt, ##__VA_ARGS__)
    ^
  ./arch/microblaze/include/asm/uaccess.h:101:3: note: in expansion of macro 'pr_debug'
     pr_debug("ACCESS fail: %s at 0x%08x (size 0x%x), seg 0x%08x\n",
     ^
Signed-off-by: Chen Gang <gang.chen.5i5j@gmail.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>

"entry.h" needs 'asmlinkage', and "asm/linkage.h" does not provide it.
So need include "linux/linkage.h" to use generic one instead of.

The related error (with allmodconfig under microblaze):

    CC [M]  drivers/net/ethernet/emulex/benet/be_main.o
  In file included from ./arch/microblaze/include/asm/processor.h:17:0,
                   from include/linux/prefetch.h:14,
                   from drivers/net/ethernet/emulex/benet/be_main.c:18:
  ./arch/microblaze/include/asm/entry.h:33:19: error: expected '=', ',', ';', 'asm' or '__attribute__' before 'void'
   extern asmlinkage void do_notify_resume(struct pt_regs *regs, int in_syscall);
                     ^
Signed-off-by: Chen Gang <gang.chen.5i5j@gmail.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>

Pull ext4 bugfix from Ted Ts'o.

[ Hmm.  It's possible we should make kfree() aware of error pointers,
  and use IS_ERR_OR_NULL rather than a NULL check.  But in the meantime
  this is obviously the right fix.  - Linus ]

* 'for_linus_urgent' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4:
  ext4: avoid trying to kfree an ERR_PTR pointer

Pull nfsd bugfixes from Bruce Fields:
 "A couple minor nfsd bugfixes"

* 'for-3.17' of git://linux-nfs.org/~bfields/linux:
  lockd: fix rpcbind crash on lockd startup failure
  nfsd4: fix rd_dircount enforcement

Nikita Yuschenko reported that booting a kernel with init=/bin/sh and
then nfs mounting without portmap or rpcbind running using a busybox
mount resulted in:

  # mount -t nfs 10.30.130.21:/opt /mnt
  svc: failed to register lockdv1 RPC service (errno 111).
  lockd_up: makesock failed, error=-111
  Unable to handle kernel paging request for data at address 0x00000030
  Faulting instruction address: 0xc055e65c
  Oops: Kernel access of bad area, sig: 11 [#1]
  MPC85xx CDS
  Modules linked in:
  CPU: 0 PID: 1338 Comm: mount Not tainted 3.10.44.cge #117
  task: cf29cea0 ti: cf35c000 task.ti: cf35c000
  NIP: c055e65c LR: c0566490 CTR: c055e648
  REGS: cf35dad0 TRAP: 0300   Not tainted  (3.10.44.cge)
  MSR: 00029000 <CE,EE,ME>  CR: 22442488  XER: 20000000
  DEAR: 00000030, ESR: 00000000

  GPR00: c05606f4 cf35db80 cf29cea0 cf0ded80 cf0dedb8 00000001 1dec3086
  00000000
  GPR08: 00000000 c07b1640 00000007 1dec3086 22442482 100b9758 00000000
  10090ae8
  GPR16: 00000000 000186a5 00000000 00000000 100c3018 bfa46edc 100b0000
  bfa46ef0
  GPR24: cf386ae0 c07834f0 00000000 c0565f88 00000001 cf0dedb8 00000000
  cf0ded80
  NIP [c055e65c] call_start+0x14/0x34
  LR [c0566490] __rpc_execute+0x70/0x250
  Call Trace:
  [cf35db80] [00000080] 0x80 (unreliable)
  [cf35dbb0] [c05606f4] rpc_run_task+0x9c/0xc4
  [cf35dbc0] [c0560840] rpc_call_sync+0x50/0xb8
  [cf35dbf0] [c056ee90] rpcb_register_call+0x54/0x84
  [cf35dc10] [c056f24c] rpcb_register+0xf8/0x10c
  [cf35dc70] [c0569e18] svc_unregister.isra.23+0x100/0x108
  [cf35dc90] [c0569e38] svc_rpcb_cleanup+0x18/0x30
  [cf35dca0] [c0198c5c] lockd_up+0x1dc/0x2e0
  [cf35dcd0] [c0195348] nlmclnt_init+0x2c/0xc8
  [cf35dcf0] [c015bb5c] nfs_start_lockd+0x98/0xec
  [cf35dd20] [c015ce6c] nfs_create_server+0x1e8/0x3f4
  [cf35dd90] [c0171590] nfs3_create_server+0x10/0x44
  [cf35dda0] [c016528c] nfs_try_mount+0x158/0x1e4
  [cf35de20] [c01670d0] nfs_fs_mount+0x434/0x8c8
  [cf35de70] [c00cd3bc] mount_fs+0x20/0xbc
  [cf35de90] [c00e4f88] vfs_kern_mount+0x50/0x104
  [cf35dec0] [c00e6e0c] do_mount+0x1d0/0x8e0
  [cf35df10] [c00e75ac] SyS_mount+0x90/0xd0
  [cf35df40] [c000ccf4] ret_from_syscall+0x0/0x3c

The addition of svc_shutdown_net() resulted in two calls to
svc_rpcb_cleanup(); the second is no longer necessary and crashes when
it calls rpcb_register_call with clnt=NULL.
Reported-by: Nikita Yushchenko <nyushchenko@dev.rtsoft.ru>
Fixes: 679b033d "lockd: ensure we tear down any live sockets when socket creation fails during lockd_up"
Cc: stable@vger.kernel.org
Acked-by: Jeff Layton <jlayton@primarydata.com>
Signed-off-by: J. Bruce Fields <bfields@redhat.com>

Commit 3b299709 "nfsd4: enforce rd_dircount" totally misunderstood
rd_dircount; it refers to total non-attribute bytes returned, not number
of directory entries returned.

Bring the code into agreement with RFC 3530 section 14.2.24.

Cc: stable@vger.kernel.org
Fixes: 3b299709 "nfsd4: enforce rd_dircount"
Signed-off-by: J. Bruce Fields <bfields@redhat.com>

Pull s390 fixes from Martin Schwidefsky:
 "A bug fix for the vdso code, the loadparm for booting from SCSI is
  added and the access permissions for the dasd module parameters are
  corrected"

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
  s390/vdso: remove NULL pointer check from clock_gettime
  s390/ipl: Add missing SCSI loadparm attributes to /sys/firmware
  s390/dasd: Make module parameter visible in sysfs