In the earlier commit dad3f793 ("usb: dwc2: Make sure we
disconnect the gadget state"), I was trying to fix up the
fact that we somehow weren't disconnecting the gadget state,
so that when the OTG port was plugged in the second time we
would get warnings about the state tracking being wrong.

(This seems to be due to a quirk of the HiKey board where
we do not ever get any otg interrupts, particularly the session
end detected signal. Instead we only see status change
interrupt.)

The fix there was somewhat simple, as it just made sure to
call dwc2_hsotg_disconnect() before we connected things up
in OTG mode, ensuring the state handling didn't throw errors.

But in looking at a different issue I was seeing with UDC
state handling, I realized that it would be much better
to call dwc2_hsotg_disconnect when we get the state change
signal moving to host mode.

Thus, this patch removes the earlier disconnect call I added
and moves it (and the needed locking) to the host mode
transition.

Cc: Wei Xu <xuwei5@hisilicon.com>
Cc: Guodong Xu <guodong.xu@linaro.org>
Cc: Amit Pundir <amit.pundir@linaro.org>
Cc: YongQin Liu <yongqin.liu@linaro.org>
Cc: John Youn <johnyoun@synopsys.com>
Cc: Minas Harutyunyan <Minas.Harutyunyan@synopsys.com>
Cc: Douglas Anderson <dianders@chromium.org>
Cc: Chen Yu <chenyu56@huawei.com>
Cc: Felipe Balbi <felipe.balbi@linux.intel.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: linux-usb@vger.kernel.org
Acked-by: Minas Harutyunyan <hminas@synopsys.com>
Tested-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: John Stultz <john.stultz@linaro.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

Driver currently notifies only USB2 PHY on USB mode change.
Extend this to USB3 PHY so that PHY drivers based on the
mode can release system resources - clocks, regulators etc.
Additionally Qualcomm QMP and QUSB2 PHY drivers need to
override VBUS signal in PHY wrapper in device mode as USB
VBUS line is not connected to PHYs. Also, remove NULL checks
for PHY when calling phy_set_mode as PHY ops already check this.
Signed-off-by: Manu Gautam <mgautam@codeaurora.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

Driver currently resumes and increments pm usage_count
of its child device (dwc3 main) from its runtime_resume
handler. This requires dwc3 runtime_resume to perform
pm_runtime_put to decrement the pm usage_count. However
runtime_put from dwc3 happens for non pci drivers
(e.g. dwc3-if-simple.c) as well which results in dwc3
pm usage_count becoming negative after couple of
runtime suspend resume iterations. Fix this by
performing runtime_get/put from dwc3-pci driver only
using workqueue.
Signed-off-by: Manu Gautam <mgautam@codeaurora.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

Driver powers-off PHYs and reinitializes DWC3 core and gadget on
resume. While this works fine for gadget mode but in host
mode there is not re-initialization of host stack. Also, resetting
bus as part of bus_suspend/resume is not correct which could affect
(or disconnect) connected devices.
Fix this by not reinitializing core on suspend/resume in host mode
for HOST only and OTG/drd configurations.
Signed-off-by: Manu Gautam <mgautam@codeaurora.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

If devm_extcon_dev_allocate() fails, we should disable clk before return.

Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Fixes: 860d2686 ("usb: phy: tahvo: Use devm_extcon_dev_[allocate|register]() and replace deprecated API")
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.

Addresses-Coverity-ID: 1350962
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.

Addresses-Coverity-ID: 1222118
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.

Addresses-Coverity-ID: 703128
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.

Addresses-Coverity-ID: 145713
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

usb_endpoint_maxp() has an inline keyword and searches for bits[10:0]
by & operation with 0x7ff. So, we can remove the duplicate & operation
with 0x7ff.
Signed-off-by: Jaejoong Kim <climbbb.kim@gmail.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

usb_endpoint_maxp() has an inline keyword and searches for bits[10:0]
by & operation with 0x7ff. So, we can remove the duplicate & operation
with 0x7ff.
Signed-off-by: Jaejoong Kim <climbbb.kim@gmail.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

usb_endpoint_maxp() has an inline keyword and searches for bits[10:0]
by & operation with 0x7ff. So, we can remove the duplicate & operation
with 0x7ff.
Signed-off-by: Jaejoong Kim <climbbb.kim@gmail.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

Add support to get a list of resets available for the device.
These resets must be kept de-asserted until the device is
in use.
Signed-off-by: Vivek Gautam <vivek.gautam@codeaurora.org>
[p.zabel@pengutronix.de: switch to hidden reset control array]
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

Move clock handling after of_platform_depopulate to achieve
a sequence that is reverse of the probe sequence.

Cc: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Vivek Gautam <vivek.gautam@codeaurora.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

This patch adds support for r8a7743/5 SoCs. The Renesas RZ/G1[ME]
(R8A7743/5) usbhs is identical to the R-Car Gen2 family.

No driver change is needed due to the fallback compatible value
"renesas,rcar-gen2-usbhs".
Adding the SoC-specific compatible values here has two purposes:
  1. Document which SoCs have this hardware module,
  2. Allow checkpatch to validate compatible values.
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Signed-off-by: Chris Paterson <chris.paterson2@renesas.com>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

For the case where an external VBUS is used, we should enable the external
VBUS comparator in the driver. This would prevent an unnecessary
overcurrent error which would then disable the host port.

This patch uses the standard 'disable-over-current' binding to allow of the
option of disabling the over-current condition.
Reviewed-by: Marek Vasut <marex@denx.de>
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

Remove optional pinctrls due to using FORCE/RG_IDDIG to implement
manual switch function.
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

Remove dummy clocks for usb wakeup and add optional ones for
mcu_bus and dma_bus bus.
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

Add a new optional property to disable u3ports
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

When set otg_sel(SSUSB_U2_PORT_OTG_SEL) for u2port which supports
dual-role mode, the controller will automatically switch mode
between host and device according to IDDIG signal. But if the
u2port only supports device mode, and no IDDIG pin is provided,
setting otg_sel may cause failure of detection by host.
So set it only for dual-role mode.
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

Treat dr_mode of USB_DR_MODE_UNKNOWN as USB_DR_MODE_OTG to
enhance functional robustness.
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

When dr_mode is set as USB_DR_MODE_HOST, it's better to try to
get optional vbus, this can increase flexibility, although we
can set vbus as always on for regulator or put it in host driver
to turn it on.
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

Support SuperSpeedPlus for usb3.1 device IP
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

In order to keep manual DRD switch independent on IDDIG interrupt,
make use of FORCE/RG_IDDIG instead of IDDIG EINT interrupt to
implement manual DRD switch function.
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

add support for 36-bit DMA address

[ Felipe Balbi: fix printk format for dma_addr_t ]
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

There are mcu_bus and dma_bus clocks needed to be turned on/off by
driver on some SoCs, so add them as optional ones
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

The wakeup debounce clocks for each ports in fact are not
needed, so remove them.
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

Add support to disable specific usb3 ports, it's useful when
usb3 phy is shared with PCIe or SATA, because we should disable
the corresponding usb3 port if the phy is used by PCIe or SATA.
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

When failing to get IRQ number, platform_get_irq() may return
-EPROBE_DEFER, but we ignore it and always return -ENODEV,
so fix it.
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

Many variables in ep0 are set but never used, so should be removed.
Signed-off-by: Christos Gkekas <chris.gekas@gmail.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

This patch adds the dwc2_set_params function for STM32F7xx USB OTG HS.
Signed-off-by: Amelie Delaunay <amelie.delaunay@st.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

This patch adds binding documentation for DWC2 controller in HS mode found
on STMicroelectronics STM32F7xx SoC.
Signed-off-by: Amelie Delaunay <amelie.delaunay@st.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

Make this const as it is only stored in the const field of a structure
video_device in the file referencing it. Make the declaration const too.

Done using Coccinelle.
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

Use the of_device_get_match_data() helper instead of open coding,
postponing the matching until when it's really needed.
Note that the renesas_usb3 driver is used with DT only, so there's
always a valid match.
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

Use the of_device_get_match_data() helper instead of open coding.
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

This patch adds support for generic phy as an optional. If you want
to use a generic phy (e.g. phy-rcar-gen3-usb3 driver) on this driver,
you have to do "insmod phy-rcar-gen3-usb3.ko" first for now.
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

This patch adds support suspend/resume functions
Signed-off-by: Kazuya Mizuguchi <kazuya.mizuguchi.ks@renesas.com>
[shimoda: add the commit log]
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

This patch moves pm_runtime_{en,dis}able() call timing to
renesas_usb3_{probe,remove}() for supporting PM_SLEEP feature in
the future.
Signed-off-by: Kazuya Mizuguchi <kazuya.mizuguchi.ks@renesas.com>
[shimoda: Revise the commit log]
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

This patch adds support for R-Car D3. This SoC needs to release
the PLL reset by the UGCTRL register. So, since this is not the same
as other R-Car Gen3 SoCs, this patch adds a new type as
"USBHS_TYPE_RCAR_GEN3_WITH_PLL".
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

This patch unifies the Gen2 and Gen3 pipe_config setting on
usbhs_parse_dt().
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>