- 09 Jul, 2015 7 commits
-
-
Johannes Thumshirn authored
Destroy minor_idr on module_exit, reclaiming the allocated memory. This was detected by the following semantic patch (written by Luis Rodriguez <mcgrof@suse.com>) <SmPL> @ defines_module_init @ declarer name module_init, module_exit; declarer name DEFINE_IDR; identifier init; @@ module_init(init); @ defines_module_exit @ identifier exit; @@ module_exit(exit); @ declares_idr depends on defines_module_init && defines_module_exit @ identifier idr; @@ DEFINE_IDR(idr); @ on_exit_calls_destroy depends on declares_idr && defines_module_exit @ identifier declares_idr.idr, defines_module_exit.exit; @@ exit(void) { ... idr_destroy(&idr); ... } @ missing_module_idr_destroy depends on declares_idr && defines_module_exit && !on_exit_calls_destroy @ identifier declares_idr.idr, defines_module_exit.exit; @@ exit(void) { ... +idr_destroy(&idr); } </SmPL> Signed-off-by: Johannes Thumshirn <jthumshirn@suse.de> Signed-off-by: David S. Miller <davem@davemloft.net>
-
git://git.kernel.org/pub/scm/linux/kernel/git/pablo/nfDavid S. Miller authored
Pablo Neira Ayuso says: ==================== Netfilter fixes for net The following patchset contains Netfilter fixes for your net tree. This batch mostly comes with patches to address fallout from the previous merge window cycle, they are: 1) Use entry->state.hook_list from nf_queue() instead of the global nf_hooks which is not valid when used from NFPROTO_NETDEV, this should cause no problems though since we have no userspace queueing for that family, but let's fix this now for the sake of correctness. Patch from Eric W. Biederman. 2) Fix compilation breakage in bridge netfilter if CONFIG_NF_DEFRAG_IPV4 is not set, from Bernhard Thaler. 3) Use percpu jumpstack in arptables too, now that there's a single copy of the rule blob we can't store the return address there anymore. Patch from Florian Westphal. 4) Fix a skb leak in the xmit path of bridge netfilter, problem there since 2.6.37 although it should be not possible to hit invalid traffic there, also from Florian. 5) Eric Leblond reports that when loading a large ruleset with many missing modules after a fresh boot, nf_tables can take long time commit it. Fix this by processing the full batch until the end, even on missing modules, then abort only once and restart processing. 6) Add bridge netfilter files to the MAINTAINER files. 7) Fix a net_device refcount leak in the new IPV6 bridge netfilter code, from Julien Grall. ==================== Signed-off-by: David S. Miller <davem@davemloft.net>
-
Peter Dunning authored
The limit for BQL is updated each time we call netdev_tx_completed_queue. Without this patch the BQL limit was updated for every TX event we see. The issue was that this only updated the limit to handle the data we complete in two events as the first event wouldn't show that enough traffic had been processed between them. This was OK when interrupt moderation was off but not when it was on as more data had to be completed in a single interrupt. The patch changes this so that we do report the completion to BQL only when all the TX events in the interrupt have been processed. Signed-off-by: Shradha Shah <sshah@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Zheng Liu authored
This device is sold as 'NVIDIA Tegra USB 3.0 Ethernet'. Chipset is RTL8153 and works with r8152. Signed-off-by: Zheng Liu <zhliu@nvidia.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Denys Vlasenko authored
As its first order of business, boomerang_interrupt() checks whether the device really has any pending interrupts. If it does not, it does nothing and returns, but it still returns IRQ_HANDLED. This is wrong: interrupt was not handled, IRQ handlers of other devices sharing this IRQ line need to be called. vortex_interrupt() has it right: it returns IRQ_NONE in this case via IRQ_RETVAL(0). Do the same in boomerang_interrupt(). Signed-off-by: Denys Vlasenko <dvlasenk@redhat.com> CC: David S. Miller <davem@davemloft.net> CC: linux-kernel@vger.kernel.org CC: netdev@vger.kernel.org Signed-off-by: David S. Miller <davem@davemloft.net>
-
Neil Horman authored
vmxnet3's current napi path is built to count every rx descriptor we recieve, and use that as a count of the napi budget. That means its possible to return from a napi poll halfway through recieving a fragmented packet accross multiple dma descriptors. If that happens, the next napi poll will start with the descriptor ring in an improper state (e.g. the first descriptor we look at may have the end-of-packet bit set), which will cause a BUG halt in the driver. Fix the issue by only counting whole received packets in the napi poll and returning that value, rather than the descriptor count. Tested by the reporter and myself, successfully Signed-off-by: Neil Horman <nhorman@tuxdriver.com> CC: Shreyas Bhatewara <sbhatewara@vmware.com> CC: "David S. Miller" <davem@davemloft.net> Acked-by: Andy Gospodarek <gospo@cumulusnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Andy Gospodarek authored
This kernel patch exports the value of the new ignore_routes_with_linkdown via netconf. v2: changes to notify userspace via netlink when sysctl values change and proposed for 'net' since this could be considered a bugfix Signed-off-by: Andy Gospodarek <gospo@cumulusnetworks.com> Suggested-by: Nicolas Dichtel <nicolas.dichtel@6wind.com> Acked-by: Nicolas Dichtel <nicolas.dichtel@6wind.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
- 08 Jul, 2015 22 commits
-
-
Shradha Shah authored
This patch avoids the double up_write to filter_sem if efx_net_open() fails. Resolves: 2d432f20Signed-off-by: Shradha Shah <sshah@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Nikolay Aleksandrov authored
Since commit b0e9a30d ("bridge: Add vlan id to multicast groups") there's a check in br_ip_equal() for a matching vlan id, but the mdb functions were not modified to use (or at least zero it) so when an entry was added it would have a garbage vlan id (from the local br_ip variable in __br_mdb_add/del) and this would prevent it from being matched and also deleted. So zero out the whole local ip var to protect ourselves from future changes and also to fix the current bug, since there's no vlan id support in the mdb uapi - use always vlan id 0. Example before patch: root@debian:~# bridge mdb add dev br0 port eth1 grp 239.0.0.1 permanent root@debian:~# bridge mdb dev br0 port eth1 grp 239.0.0.1 permanent root@debian:~# bridge mdb del dev br0 port eth1 grp 239.0.0.1 permanent RTNETLINK answers: Invalid argument After patch: root@debian:~# bridge mdb add dev br0 port eth1 grp 239.0.0.1 permanent root@debian:~# bridge mdb dev br0 port eth1 grp 239.0.0.1 permanent root@debian:~# bridge mdb del dev br0 port eth1 grp 239.0.0.1 permanent root@debian:~# bridge mdb Signed-off-by: Nikolay Aleksandrov <razor@blackwall.org> Fixes: b0e9a30d ("bridge: Add vlan id to multicast groups") Signed-off-by: David S. Miller <davem@davemloft.net>
-
Mugunthan V N authored
When cpsw's number of slave is set to 1 in device tree and while accessing second slave ndev and priv in cpsw_tx_interrupt(), there is a kernel crash. This is due to cpsw_get_slave_priv() not verifying number of slaves while retriving netdev priv and returns a invalid memory region. Fixing the issue by introducing number of slave check in cpsw_get_slave_priv() and cpsw_get_slave_ndev(). [ 15.879589] Unable to handle kernel paging request at virtual address 0f0e142c [ 15.888540] pgd = ed374000 [ 15.891359] [0f0e142c] *pgd=00000000 [ 15.895105] Internal error: Oops: 5 [#1] SMP ARM [ 15.899936] Modules linked in: [ 15.903139] CPU: 0 PID: 593 Comm: udhcpc Tainted: G W 4.1.0-12205-gfda8b18c-dirty #10 [ 15.912386] Hardware name: Generic AM43 (Flattened Device Tree) [ 15.918557] task: ed2a2e00 ti: ed3fe000 task.ti: ed3fe000 [ 15.924187] PC is at cpsw_tx_interrupt+0x30/0x44 [ 15.929008] LR is at _raw_spin_unlock_irqrestore+0x40/0x44 [ 15.934726] pc : [<c048b9cc>] lr : [<c05ef4f4>] psr: 20000193 [ 15.934726] sp : ed3ffc08 ip : ed2a2e40 fp : 00000000 [ 15.946685] r10: c0969ce8 r9 : c0969cfc r8 : 00000000 [ 15.952129] r7 : 000000c6 r6 : ee54ab00 r5 : ee169c64 r4 : ee534e00 [ 15.958932] r3 : 0f0e0d0c r2 : 00000000 r1 : ed3ffbc0 r0 : 00000001 [ 15.965735] Flags: nzCv IRQs off FIQs on Mode SVC_32 ISA ARM Segment user [ 15.973261] Control: 10c5387d Table: ad374059 DAC: 00000015 [ 15.979246] Process udhcpc (pid: 593, stack limit = 0xed3fe218) [ 15.985414] Stack: (0xed3ffc08 to 0xed400000) [ 15.989954] fc00: ee54ab00 c009928c c0a9e648 60000193 000032e4 ee169c00 [ 15.998478] fc20: ee169c64 ee169c00 ee169c64 ee54ab00 00000001 00000001 ee67e268 ee008800 [ 16.006995] fc40: ee534800 c009946c ee169c00 ee169c64 c08bd660 c009c370 c009c2a4 000000c6 [ 16.015513] fc60: c08b75c4 c08b0854 00000000 c0098b3c 000000c6 c0098c50 ed3ffcb0 0000003a [ 16.024033] fc80: ed3ffcb0 fa24010c c08b7800 fa240100 ee7e9880 c00094c4 c05ef4e8 60000013 [ 16.032556] fca0: ffffffff ed3ffce4 ee7e9880 c05ef964 00000001 ed2a33d8 00000000 ed2a2e00 [ 16.041080] fcc0: 60000013 ee536bf8 60000013 ee51b800 ee7e9880 ee67e268 ee7e9880 ee534800 [ 16.049603] fce0: c0ad0768 ed3ffcf8 c008e910 c05ef4e8 60000013 ffffffff 00000001 00000001 [ 16.058121] fd00: ee536bf8 c0487a04 00000000 00000000 ee534800 00000000 00000156 c048c990 [ 16.066645] fd20: 00000000 00000000 c0969f40 00000000 00000000 c05000e8 00000001 00000000 [ 16.075167] fd40: 00000000 c051eefc 00000000 ee67e268 00000000 00000000 ee51b800 ed3ffd9c [ 16.083690] fd60: 00000000 ee67e200 ee51b800 ee7e9880 ee67e268 00000000 00000000 ee67e200 [ 16.092211] fd80: ee51b800 ee7e9880 ee67e268 ee534800 ee67e200 c051eedc ee67e268 00000010 [ 16.100727] fda0: 00000000 00000000 ee7e9880 ee534800 00000000 ee67e268 ee51b800 c05006fc [ 16.109247] fdc0: ee67e268 00000001 c0500488 00000156 ee7e9880 00000000 ed3fe000 fffffff4 [ 16.117771] fde0: ed3fff1c ee7e9880 ee534800 00000148 00000000 ed1f8340 00000000 00000000 [ 16.126289] fe00: 00000000 c05a9054 00000000 00000000 00000156 c0ab62a8 00000010 ed3e7000 [ 16.134812] fe20: 00000000 00000008 edcfb700 ed3fff1c c0fb5f94 ed2a2e00 c0fb5f64 000005d8 [ 16.143336] fe40: c0a9b3b8 00000000 ed3e7070 00000000 00000000 00000000 00009f40 00000000 [ 16.151858] fe60: 00000000 00020022 00110008 00000000 00000000 43004400 00000000 ffffffff [ 16.160374] fe80: 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 [ 16.168898] fea0: edcfb700 bee5f380 00000014 00000000 ed3fe000 00000000 00004400 c04e2b64 [ 16.177415] fec0: 00000002 c04e3b00 ed3ffeec 00000001 0000011a 00000000 00000000 bee5f394 [ 16.185937] fee0: 00000148 ed3fff10 00000014 00000001 00000000 00000000 ed3ffee4 00000000 [ 16.194459] ff00: 00000000 00000000 00000000 c04e3664 00080011 00000002 06000000 ffffffff [ 16.202980] ff20: 0000ffff ffffffff 0000ffff c008dd54 ee5a6f08 ee636e80 c096972d c0089c14 [ 16.211499] ff40: 00000000 60000013 ee5a6f40 60000013 00000000 ee5a6f40 00000002 00000006 [ 16.220023] ff60: 00000000 edcfb700 00000001 ed2a2e00 c000f60c 00000001 0000011a c008ea34 [ 16.228540] ff80: 00000006 00000000 bee5f380 00000014 bee5f380 00000014 bee5f380 00000122 [ 16.237059] ffa0: c000f7c4 c000f5e0 bee5f380 00000014 00000006 bee5f394 00000148 00000000 [ 16.245581] ffc0: bee5f380 00000014 bee5f380 00000122 fffffd6e 00004300 00004800 00004400 [ 16.254104] ffe0: bee5f378 bee5f36c 000307ec b6f39044 40000010 00000006 ed36fa40 00000000 [ 16.262642] [<c048b9cc>] (cpsw_tx_interrupt) from [<c009928c>] (handle_irq_event_percpu+0x64/0x204) [ 16.272076] [<c009928c>] (handle_irq_event_percpu) from [<c009946c>] (handle_irq_event+0x40/0x64) [ 16.281330] [<c009946c>] (handle_irq_event) from [<c009c370>] (handle_fasteoi_irq+0xcc/0x1a8) [ 16.290220] [<c009c370>] (handle_fasteoi_irq) from [<c0098b3c>] (generic_handle_irq+0x20/0x30) [ 16.299197] [<c0098b3c>] (generic_handle_irq) from [<c0098c50>] (__handle_domain_irq+0x64/0xdc) [ 16.308273] [<c0098c50>] (__handle_domain_irq) from [<c00094c4>] (gic_handle_irq+0x20/0x60) [ 16.316987] [<c00094c4>] (gic_handle_irq) from [<c05ef964>] (__irq_svc+0x44/0x5c) [ 16.324779] Exception stack(0xed3ffcb0 to 0xed3ffcf8) [ 16.330044] fca0: 00000001 ed2a33d8 00000000 ed2a2e00 [ 16.338567] fcc0: 60000013 ee536bf8 60000013 ee51b800 ee7e9880 ee67e268 ee7e9880 ee534800 [ 16.347090] fce0: c0ad0768 ed3ffcf8 c008e910 c05ef4e8 60000013 ffffffff [ 16.353987] [<c05ef964>] (__irq_svc) from [<c05ef4e8>] (_raw_spin_unlock_irqrestore+0x34/0x44) [ 16.362973] [<c05ef4e8>] (_raw_spin_unlock_irqrestore) from [<c0487a04>] (cpdma_check_free_tx_desc+0x60/0x6c) [ 16.373311] [<c0487a04>] (cpdma_check_free_tx_desc) from [<c048c990>] (cpsw_ndo_start_xmit+0xb4/0x1ac) [ 16.383017] [<c048c990>] (cpsw_ndo_start_xmit) from [<c05000e8>] (dev_hard_start_xmit+0x2a4/0x4c0) [ 16.392364] [<c05000e8>] (dev_hard_start_xmit) from [<c051eedc>] (sch_direct_xmit+0xf4/0x210) [ 16.401246] [<c051eedc>] (sch_direct_xmit) from [<c05006fc>] (__dev_queue_xmit+0x2ac/0x7bc) [ 16.409960] [<c05006fc>] (__dev_queue_xmit) from [<c05a9054>] (packet_sendmsg+0xc68/0xeb4) [ 16.418585] [<c05a9054>] (packet_sendmsg) from [<c04e2b64>] (sock_sendmsg+0x14/0x24) [ 16.426663] [<c04e2b64>] (sock_sendmsg) from [<c04e3b00>] (SyS_sendto+0xb4/0xe0) [ 16.434377] [<c04e3b00>] (SyS_sendto) from [<c000f5e0>] (ret_fast_syscall+0x0/0x54) [ 16.442360] Code: e5943118 e593303c e3530000 0a000002 (e5930720) [ 16.448716] ---[ end trace a68159f094d85ba6 ]--- [ 16.453526] Kernel panic - not syncing: Fatal exception in interrupt [ 16.460149] ---[ end Kernel panic - not syncing: Fatal exception in interrupt Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com> Cc: <stable@vger.kernel.org> # v3.8+ Signed-off-by: David S. Miller <davem@davemloft.net>
-
Stephen Smalley authored
Calling connect() with an AF_TIPC socket would trigger a series of error messages from SELinux along the lines of: SELinux: Invalid class 0 type=AVC msg=audit(1434126658.487:34500): avc: denied { <unprintable> } for pid=292 comm="kworker/u16:5" scontext=system_u:system_r:kernel_t:s0 tcontext=system_u:object_r:unlabeled_t:s0 tclass=<unprintable> permissive=0 This was due to a failure to initialize the security state of the new connection sock by the tipc code, leaving it with junk in the security class field and an unlabeled secid. Add a call to security_sk_clone() to inherit the security state from the parent socket. Reported-by: Tim Shearer <tim.shearer@overturenetworks.com> Signed-off-by: Stephen Smalley <sds@tycho.nsa.gov> Acked-by: Paul Moore <paul@paul-moore.com> Acked-by: Ying Xue <ying.xue@windriver.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
David S. Miller authored
Shradha Shah says: ==================== sfc: compat for lack of VADAPTOR_SET_MAC in adaptor_firmware <= 4.1.1.1023 This patch series resolves an incompatibility with legacy firmware due to the lack of MC_CMD_VADAPTOR_SET_MAC in adaptor_firmware <= 4.1.1.1023 Unless this patch series is applied there will be a compatibility issue between the driver and Solarflare adapters running older firmware. Tested with and without CONFIG_SFC_SRIOV ==================== Signed-off-by: David S. Miller <davem@davemloft.net>
-
Daniel Pieczko authored
Signed-off-by: Shradha Shah <sshah@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Daniel Pieczko authored
Some versions of MCFW do not support the MC_CMD_VADAPTOR_SET_MAC command, and ENOSYS will be returned. If the PF created its own vport, the function's datapath must be stopped and the vport can be reconfigured to reflect the new MAC address. If the MCFW created the vport for the PF (which is the case when the nic_data->vport_mac is blank), nothing further needs to be done as the vport is not under the control of the PF. This only applies to PFs because the MCFW in question does not support VFs. Signed-off-by: Shradha Shah <sshah@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Daniel Pieczko authored
Re-organize the structure of error handling to avoid having to duplicate the netif_err() around the ifdefs. The only change to the behaviour of the error-handling is that the PF's data structure to record VF details should only be updated if the original command succeeded. Signed-off-by: Shradha Shah <sshah@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Mazhar Rana authored
When "primary_reselect" is set to "failure", primary interface should not become active until current active slave is down. But if we set first member of bond device as a "primary" interface and "primary_reselect" is set to "failure" then whenever primary interface's link get back(up) it become active slave even if current active slave is still up. With this patch, "bond_find_best_slave" will not traverse members if primary interface is not candidate for failover/reselection and current active slave is still up. Signed-off-by: Mazhar Rana <mazhar.rana@cyberoam.com> Signed-off-by: Jay Vosburgh <j.vosburgh@gmail.com> Signed-off-by: Jay Vosburgh <jay.vosburgh@canonical.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Timo Teräs authored
Frag needed should be sent only if the inner header asked to not fragment. Currently fragmentation is broken if the tunnel has df set, but df was not asked in the original packet. The tunnel's df needs to be still checked to update internally the pmtu cache. Commit 23a3647b broke it, and this commit fixes the ipv4 df check back to the way it was. Fixes: 23a3647b ("ip_tunnels: Use skb-len to PMTU check.") Cc: Pravin B Shelar <pshelar@nicira.com> Signed-off-by: Timo Teräs <timo.teras@iki.fi> Acked-by: Pravin B Shelar <pshelar@nicira.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Daniel Borkmann authored
Jason Gunthorpe reported that since commit c02db8c6 ("rtnetlink: make SR-IOV VF interface symmetric"), we don't verify IFLA_VF_INFO attributes anymore with respect to their policy, that is, ifla_vfinfo_policy[]. Before, they were part of ifla_policy[], but they have been nested since placed under IFLA_VFINFO_LIST, that contains the attribute IFLA_VF_INFO, which is another nested attribute for the actual VF attributes such as IFLA_VF_MAC, IFLA_VF_VLAN, etc. Despite the policy being split out from ifla_policy[] in this commit, it's never applied anywhere. nla_for_each_nested() only does basic nla_ok() testing for struct nlattr, but it doesn't know about the data context and their requirements. Fix, on top of Jason's initial work, does 1) parsing of the attributes with the right policy, and 2) using the resulting parsed attribute table from 1) instead of the nla_for_each_nested() loop (just like we used to do when still part of ifla_policy[]). Reference: http://thread.gmane.org/gmane.linux.network/368913 Fixes: c02db8c6 ("rtnetlink: make SR-IOV VF interface symmetric") Reported-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com> Cc: Chris Wright <chrisw@sous-sol.org> Cc: Sucheta Chakraborty <sucheta.chakraborty@qlogic.com> Cc: Greg Rose <gregory.v.rose@intel.com> Cc: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Cc: Rony Efraim <ronye@mellanox.com> Cc: Vlad Zolotarov <vladz@cloudius-systems.com> Cc: Nicolas Dichtel <nicolas.dichtel@6wind.com> Cc: Thomas Graf <tgraf@suug.ch> Signed-off-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Acked-by: Vlad Zolotarov <vladz@cloudius-systems.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Andrew Lunn authored
When a switch is attached to the mdio bus, the mdio bus can be used while the interface is not open. If the IPG clock is not enabled, MDIO reads/writes will simply time out. Add support for runtime PM to control this clock. Enable/disable this clock using runtime PM, with open()/close() and mdio read()/write() function triggering runtime PM operations. Since PM is optional, the IPG clock is enabled at probe and is no longer modified by fec_enet_clk_enable(), thus if PM is not enabled in the kernel, it is guaranteed the clock is running when MDIO operations are performed. Signed-off-by: Andrew Lunn <andrew@lunn.ch> Acked-by: Fugang Duan <B38611@freescale.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Lendacky, Thomas authored
When running a kernel configured with CONFIG_DMA_API_DEBUG=y a warning is issued: DMA-API: device driver tries to sync DMA memory it has not allocated This warning is the result of mapping the full range of the Rx buffer pages allocated and then performing a dma_sync_single_for_cpu against a calculated DMA address. The proper thing to do is to use the dma_sync_single_range_for_cpu with a base DMA address and an offset. Reported-by: Kim Phillips <kim.phillips@arm.com> Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com> Tested-by: Kim Phillips <kim.phillips@arm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Nicolas Dichtel authored
This reverts commit e1622baf. The side effect of this commit is to add a '@NONE' after each virtual interface name with a 'ip link'. It may break existing scripts. Reported-by: Olivier Hartkopp <socketcan@hartkopp.net> Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com> Tested-by: Oliver Hartkopp <socketcan@hartkopp.net> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Eric Dumazet authored
User space can crash kernel with ip link add ifb10 numtxqueues 100000 type ifb We must replace a BUG_ON() by proper test and return -EINVAL for crazy values. Fixes: 60877a32 ("net: allow large number of tx queues") Signed-off-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Phil Sutter authored
If rhashtable_walk_next detects a resize operation in progress, it jumps to the new table and continues walking that one. But it misses to drop the reference to it's current item, leading it to continue traversing the new table's bucket in which the current item is sorted into, and after reaching that bucket's end continues traversing the new table's second bucket instead of the first one, thereby potentially missing items. This fixes the rhashtable runtime test for me. Bug probably introduced by Herbert Xu's patch eddee5ba ("rhashtable: Fix walker behaviour during rehash") although not explicitly tested. Fixes: eddee5ba ("rhashtable: Fix walker behaviour during rehash") Signed-off-by: Phil Sutter <phil@nwl.cc> Acked-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Satish Ashok authored
Start the delete timer when adding temp static entries so they can expire. Signed-off-by: Satish Ashok <sashok@cumulusnetworks.com> Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com> Fixes: ccb1c31a ("bridge: add flags to distinguish permanent mdb entires") Signed-off-by: David S. Miller <davem@davemloft.net>
-
Rob Herring authored
On UML builds, mdio-mux-mmioreg.c fails to compile: drivers/net/phy/mdio-mux-mmioreg.c:50:3: error: implicit declaration of function ‘ioremap’ [-Werror=implicit-function-declaration] drivers/net/phy/mdio-mux-mmioreg.c:63:3: error: implicit declaration of function ‘iounmap’ [-Werror=implicit-function-declaration] This is due to CONFIG_OF now being user selectable. Add a dependency on HAS_IOMEM to fix this. Signed-off-by: Rob Herring <robh@kernel.org> Cc: Florian Fainelli <f.fainelli@gmail.com> Cc: David S. Miller <davem@davemloft.net> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Ralf Baechle authored
Since 1d5da757 (ax25: Stop using magic neighbour cache operations.) any attempt to transmit IP packets over a bpqether device will result in a message like "Dead loop on virtual device bpq0, fix it urgently!" Fix suggested by Eric W. Biederman <ebiederm@xmission.com>. Signed-off-by: Ralf Baechle <ralf@linux-mips.org> Cc: <stable@vger.kernel.org> # 4.1 Signed-off-by: David S. Miller <davem@davemloft.net>
-
Eric Dumazet authored
rate estimators are limited to 4 Mpps, which was fine years ago, but too small with current hardware generation. Lets use 2^5 scaling instead of 2^10 to get 128 Mpps new limit. On 64bit arch, use an "unsigned long" for temp storage and remove limit. (We do not expect 32bit arches to be able to reach this point) Tested: tc -s -d filter sh dev eth0 parent ffff: filter protocol ip pref 1 u32 filter protocol ip pref 1 u32 fh 800: ht divisor 1 filter protocol ip pref 1 u32 fh 800::800 order 2048 key ht 800 bkt 0 flowid 1:15 match 07000000/ff000000 at 12 action order 1: gact action drop random type none pass val 0 index 1 ref 1 bind 1 installed 166 sec Action statistics: Sent 39734251496 bytes 863788076 pkt (dropped 863788117, overlimits 0 requeues 0) rate 4067Mbit 11053596pps backlog 0b 0p requeues 0 Signed-off-by: Eric Dumazet <edumazet@google.com> Acked-by: Alexei Starovoitov <ast@plumgrid.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Julien Grall authored
The commit efb6de9b "netfilter: bridge: forward IPv6 fragmented packets" introduced a new function br_validate_ipv6 which take a reference on the inet6 device. Although, the reference is not released at the end. This will result to the impossibility to destroy any netdevice using ipv6 and bridge. It's possible to directly retrieve the inet6 device without taking a reference as all netfilter hooks are protected by rcu_read_lock via nf_hook_slow. Spotted while trying to destroy a Xen guest on the upstream Linux: "unregister_netdevice: waiting for vif1.0 to become free. Usage count = 1" Signed-off-by: Julien Grall <julien.grall@citrix.com> Cc: Bernhard Thaler <bernhard.thaler@wvnet.at> Cc: Pablo Neira Ayuso <pablo@netfilter.org> Cc: fw@strlen.de Cc: ian.campbell@citrix.com Cc: wei.liu2@citrix.com Cc: Bob Liu <bob.liu@oracle.com> Acked-by: Stephen Hemminger <stephen@networkplumber.org> Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
-
Pablo Neira Ayuso authored
So scripts/get_maintainer.pl shows the Netfilter mailing lists. Reported-by: Julien Grall <julien.grall@citrix.com> Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
-
- 03 Jul, 2015 5 commits
-
-
Hariprasad Shenai authored
Part of commit 49aa284fe64c4c1 ("cxgb4: Add support for devlog") change introduced a real bug where the Device Log Sequence Numbers are no longer being converted from firmware Big-Endian to local CPU-Endian format. This patch moves all of the translation into the devlog_show() routine. The only endianness code now in devlog_open() is the small loop to find the earliest (lowest Sequence Number) Device Log entry in the circular buffer. Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Angga authored
Before commit daad1512 ("ipv6: Make ipv6_is_mld() inline and use it from ip6_mc_input().") MLD packets were only processed locally. After the change, a copy of MLD packet goes through ip6_mr_input, causing MRT6MSG_NOCACHE message to be generated to user space. Make MLD packet only processed locally. Fixes: daad1512 ("ipv6: Make ipv6_is_mld() inline and use it from ip6_mc_input().") Signed-off-by: Hermin Anggawijaya <hermin.anggawijaya@alliedtelesis.co.nz> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Markus Elfring authored
The module_put() function tests whether its argument is NULL and then returns immediately. Thus the test around the call is not needed. This issue was detected by using the Coccinelle software. Signed-off-by: Markus Elfring <elfring@users.sourceforge.net> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Markus Elfring authored
The module_put() function tests whether its argument is NULL and then returns immediately. Thus the test around the call is not needed. This issue was detected by using the Coccinelle software. Signed-off-by: Markus Elfring <elfring@users.sourceforge.net> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Markus Elfring authored
The free_percpu() function tests whether its argument is NULL and then returns immediately. Thus the test around the call is not needed. This issue was detected by using the Coccinelle software. Signed-off-by: Markus Elfring <elfring@users.sourceforge.net> Signed-off-by: David S. Miller <davem@davemloft.net>
-
- 02 Jul, 2015 6 commits
-
-
Nikolay Aleksandrov authored
Vlan ids 0 and 4095 were disallowed by commit: 8adff41c ("bridge: Don't use VID 0 and 4095 in vlan filtering") but then the check was removed when vlan ranges were introduced by: bdced7ef ("bridge: support for multiple vlans and vlan ranges in setlink and dellink requests") So reintroduce the vlan range check. Before patch: [root@testvm ~]# bridge vlan add vid 0 dev eth0 master (succeeds) After Patch: [root@testvm ~]# bridge vlan add vid 0 dev eth0 master RTNETLINK answers: Invalid argument Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com> Fixes: bdced7ef ("bridge: support for multiple vlans and vlan ranges in setlink and dellink requests") Acked-by: Toshiaki Makita <toshiaki.makita1@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
git://git.kernel.org/pub/scm/linux/kernel/git/bluetooth/bluetoothDavid S. Miller authored
Johan Hedberg says: ==================== pull request: bluetooth 2015-07-02 A couple of regressions crept in because of a patch to use proper list APIs rather than manually reading & writing the next/prev pointers (commit 835a6a2f). Turns out this was masking a few bugs: a missing INIT_LIST_HEAD() call and incorrectly using list_del() rather than list_del_init(). The two patches in this set fix these, and it'd be nice they could still make it to 4.2-rc1 to avoid new bug reports from users. Please let me know if there are any issues pulling. Thanks. ==================== Signed-off-by: David S. Miller <davem@davemloft.net>
-
Govindarajulu Varadarajan authored
In enic_poll, we clean tx and rx queues, when low latency busy socket polling is happening, enic_poll will only clean tx queue. After cleaning tx, it should return total budget for re-poll. There is a small window between vnic_intr_unmask() and enic_poll_unlock_napi(). In this window if an irq occurs and napi is scheduled on different cpu, it tries to acquire enic_poll_lock_napi() and fails. Unlock napi_poll before unmasking the interrupt. v2: Do not change tx wonk done behaviour. Consider only rx work done for completing napi. Signed-off-by: Govindarajulu Varadarajan <_govind@gmx.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
git://git.kernel.org/pub/scm/linux/kernel/git/paulg/linuxLinus Torvalds authored
Pull init.h/module.h fragility fixes from Paul Gortmaker: "Fixup various init.h misuses that are fragile wrt code moving to module.h What started as a removal of no longer required include <linux/init.h> due to the earlier __cpuinit and __devinit removal led to the observation that some module specfic support was living in init.h itself, thus preventing the full removal from introducing compile regressions. This series includes a few final fixups needed prior to the relocation of the modular init code from <init.h> to <module.h>. These are things that weren't easily categorized into any of the other previous series categories already requested for pull. That said, each fixup branch (including this one) is independent and there are no ordering constraints. Only the final code relocation (which is NOT in this pull) requires that all my cleanup branches be merged first" * tag 'module-misc-v4.1-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/paulg/linux: tile: add init.h to usb.c to avoid compile failure arm: fix implicit #include <linux/init.h> in entry asm. x86: replace __init_or_module with __init in non-modular vsmp_64.c
-
Linus Torvalds authored
Merge tag 'module-builtin_driver-v4.1-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/paulg/linux Pull module_platform_driver replacement from Paul Gortmaker: "Replace module_platform_driver with builtin_platform driver in non modules. We see an increasing number of non-modular drivers using modular_driver() type register functions. There are several downsides to letting this continue unchecked: - The code can appear modular to a reader of the code, and they won't know if the code really is modular without checking the Makefile and Kconfig to see if compilation is governed by a bool or tristate. - Coders of drivers may be tempted to code up an __exit function that is never used, just in order to satisfy the required three args of the modular registration function. - Non-modular code ends up including the <module.h> which increases CPP overhead that they don't need. - It hinders us from performing better separation of the module init code and the generic init code. So here we introduce similar macros for builtin drivers. Then we convert builtin drivers (controlled by a bool Kconfig) by making the following type of mapping: module_platform_driver() ---> builtin_platform_driver() module_platform_driver_probe() ---> builtin_platform_driver_probe(). The set of drivers that are converted here are just the ones that showed up as relying on an implicit include of <module.h> during a pending header cleanup. So we convert them here vs adding an include of <module.h> to non-modular code to avoid compile fails. Additonal conversions can be done asynchronously at any time. Once again, an unused module_exit function that is removed here appears in the diffstat as an outlier wrt all the other changes" * tag 'module-builtin_driver-v4.1-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/paulg/linux: drivers/clk: convert sunxi/clk-mod0.c to use builtin_platform_driver drivers/power: Convert non-modular syscon-reboot to use builtin_platform_driver drivers/soc: Convert non-modular soc-realview to use builtin_platform_driver drivers/soc: Convert non-modular tegra/pmc to use builtin_platform_driver drivers/cpufreq: Convert non-modular s5pv210-cpufreq.c to use builtin_platform_driver drivers/cpuidle: Convert non-modular drivers to use builtin_platform_driver drivers/platform: Convert non-modular pdev_bus to use builtin_platform_driver platform_device: better support builtin boilerplate avoidance
-
Linus Torvalds authored
Merge tag 'module_init-alternate_initcall-v4.1-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/paulg/linux Pull module_init replacement part two from Paul Gortmaker: "Replace module_init with appropriate alternate initcall in non modules. This series converts non-modular code that is using the module_init() call to hook itself into the system to instead use one of our alternate priority initcalls. Unlike the previous series that used device_initcall and hence was a runtime no-op, these commits change to one of the alternate initcalls, because (a) we have them and (b) it seems like the right thing to do. For example, it would seem logical to use arch_initcall for arch specific setup code and fs_initcall for filesystem setup code. This does mean however, that changes in the init ordering will be taking place, and so there is a small risk that some kind of implicit init ordering issue may lie uncovered. But I think it is still better to give these ones sensible priorities than to just assign them all to device_initcall in order to exactly preserve the old ordering. Thad said, we have already made similar changes in core kernel code in commit c96d6660 ("kernel: audit/fix non-modular users of module_init in core code") without any regressions reported, so this type of change isn't without precedent. It has also got the same local testing and linux-next coverage as all the other pull requests that I'm sending for this merge window have got. Once again, there is an unused module_exit function removal that shows up as an outlier upon casual inspection of the diffstat" * tag 'module_init-alternate_initcall-v4.1-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/paulg/linux: x86: perf_event_intel_pt.c: use arch_initcall to hook in enabling x86: perf_event_intel_bts.c: use arch_initcall to hook in enabling mm/page_owner.c: use late_initcall to hook in enabling lib/list_sort: use late_initcall to hook in self tests arm: use subsys_initcall in non-modular pl320 IPC code powerpc: don't use module_init for non-modular core hugetlb code powerpc: use subsys_initcall for Freescale Local Bus x86: don't use module_init for non-modular core bootflag code netfilter: don't use module_init/exit in core IPV4 code fs/notify: don't use module_init for non-modular inotify_user code mm: replace module_init usages with subsys_initcall in nommu.c
-