Skip to content

L
linux
Switch branch/tag
  1. 03 May, 2012 6 commits
    • Greg Kroah-Hartman's avatar
      USB: serial: pl2303: convert dbg() calls to dev_dbg() · d8789b2b
      Greg Kroah-Hartman authored 
      This converts the usage of dbg() to dev_dbg() where needed, and removed
a bunch of these calls where they were just "tracing" calls, which are
no longer needed.
Signed-off-by: default avatarGreg Kroah-Hartman <gregkh@linuxfoundation.org>
      d8789b2b
    • Greg Kroah-Hartman's avatar
      Merge tag 'for-usb-next-2012-05-03' of... · cbad67e3
      Greg Kroah-Hartman authored 
      Merge tag 'for-usb-next-2012-05-03' of git://git.kernel.org/pub/scm/linux/kernel/git/sarah/xhci into usb-next

xhci: isoc, Intel xHCI, and suspend races.

Hi Greg,

Here's some xHCI fixes that should be queued for 3.5.

The first patch builds on Alan Stern's 3.4 patch to close the suspend and port
event race conditions.  It's marked for 3.4 stable, since that's where Alan's
patch landed.  The second patch fixes an incorrect error code that the xHCI
driver would return when an isochronous transfer error occurred.

The third and fourth patches fix issues seen on Intel xHCI host controllers.
The third patch fixes a dead port issue that was seen on the Panther Point
EHCI/xHCI host when CONFIG_USB_XHCI_HCD was turned off.  The ports were being
switched over to xHCI, even though the xHCI driver was never even built.  The
fourth patch adds support for the EHCI to xHCI port switchover for the upcoming
Intel Lynx Point chipset.

As I said, there's nothing here that's terribly urgent, and these patches can
wait a couple weeks for the 3.5 merge window.

Thanks,
Sarah Sharp
      cbad67e3
    • Sarah Sharp's avatar
      xhci: Add Lynx Point to list of Intel switchable hosts. · 1c12443a
      Sarah Sharp authored 
      The upcoming Intel Lynx Point chipset includes an xHCI host controller
that can have ports switched from the EHCI host controller, just like
the Intel Panther Point xHCI host.  This time, ports from both EHCI
hosts can be switched to the xHCI host controller.  The PCI config
registers to do the port switching are in the exact same place in the
xHCI PCI configuration registers, with the same semantics.

Hooray for shipping patches for next-gen hardware before the current gen
hardware is even available for purchase!

This patch should be backported to stable kernels as old as 3.0,
that contain commit 69e848c2
"Intel xhci: Support EHCI/xHCI port switching."
Signed-off-by: default avatarSarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable@vger.kernel.org
      1c12443a
    • Sarah Sharp's avatar
      xhci: Avoid dead ports when CONFIG_USB_XHCI_HCD=n · 51c9e6c7
      Sarah Sharp authored 
      If the user chooses to say "no" to CONFIG_USB_XHCI_HCD on a system
with an Intel Panther Point chipset, the PCI quirks code or the EHCI
driver will switch the ports over to the xHCI host, but the xHCI driver
will never load.  The ports will be powered off and seem "dead" to the
user.

Fix this by only switching the ports over if CONFIG_USB_XHCI_HCD is
either compiled in, or compiled as a module.

This patch should be backported to stable kernels as old as 3.0,
that contain commit 69e848c2
"Intel xhci: Support EHCI/xHCI port switching."
Signed-off-by: default avatarSarah Sharp <sarah.a.sharp@linux.intel.com>
Reported-by: default avatarEric Anholt <eric.anholt@intel.com>
Reported-by: default avatarDavid Bein <d.bein@f5.com>
Cc: stable@vger.kernel.org
      51c9e6c7
    • Hans de Goede's avatar
      usb-xhci: Handle COMP_TX_ERR for isoc tds · 9c745995
      Hans de Goede authored 
      While testing unplugging an UVC HD webcam with usb-redirection (so through
usbdevfs), my userspace usb-redir code was getting a value of -1 in
iso_frame_desc[n].status, which according to Documentation/usb/error-codes.txt
is not a valid value.

The source of this -1 is the default case in xhci-ring.c:process_isoc_td()
adding a kprintf there showed the value of trb_comp_code to be COMP_TX_ERR
in this case, so this patch adds handling for that completion code to
process_isoc_td().

This was observed and tested with the following xhci controller:
1033:0194 NEC Corporation uPD720200 USB 3.0 Host Controller (rev 04)

Note: I also wonder if setting frame->status to -1 (-EPERM) is the best we can
do, but since I cannot come up with anything better I've left that as is.

This patch should be backported to kernels as old as 2.6.36, which contain the
commit 04e51901 "USB: xHCI: Isochronous
transfer implementation".
Signed-off-by: default avatarHans de Goede <hdegoede@redhat.com>
Signed-off-by: default avatarSarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable@vger.kernel.org
      9c745995
    • Andiry Xu's avatar
      xHCI: keep track of ports being resumed and indicate in hub_status_data · f370b996
      Andiry Xu authored 
      This commit adds a bit-array to xhci bus_state for keeping track of
which ports are undergoing a resume transition. If any of the bits
are set when xhci_hub_status_data() is called, the routine will return
a non-zero value even if no ports have any status changes pending.
This will allow usbcore to handle races between root-hub suspend and
port wakeup.

This patch should be backported to kernels as old as 3.4, that contain
the commit 879d38e6 "USB: fix race
between root-hub suspend and remote wakeup".
Signed-off-by: default avatarAndiry Xu <andiry.xu@amd.com>
Signed-off-by: default avatarSarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: stable@vger.kernel.org
      f370b996
  3. 02 May, 2012 34 commits
GitLab Nexedi Edition | About GitLab | About Nexedi | 沪ICP备2021021310号-2 | 沪ICP备2021021310号-7