1. 24 Sep, 2018 19 commits
    • Saif Hasan's avatar
      mpls: allow routes on ip6gre devices · d8e2262a
      Saif Hasan authored
      Summary:
      
      This appears to be necessary and sufficient change to enable `MPLS` on
      `ip6gre` tunnels (RFC4023).
      
      This diff allows IP6GRE devices to be recognized by MPLS kernel module
      and hence user can configure interface to accept packets with mpls
      headers as well setup mpls routes on them.
      
      Test Plan:
      
      Test plan consists of multiple containers connected via GRE-V6 tunnel.
      Then carrying out testing steps as below.
      
      - Carry out necessary sysctl settings on all containers
      
      ```
      sysctl -w net.mpls.platform_labels=65536
      sysctl -w net.mpls.ip_ttl_propagate=1
      sysctl -w net.mpls.conf.lo.input=1
      ```
      
      - Establish IP6GRE tunnels
      
      ```
      ip -6 tunnel add name if_1_2_1 mode ip6gre \
        local 2401:db00:21:6048:feed:0::1 \
        remote 2401:db00:21:6048:feed:0::2 key 1
      ip link set dev if_1_2_1 up
      sysctl -w net.mpls.conf.if_1_2_1.input=1
      ip -4 addr add 169.254.0.2/31 dev if_1_2_1 scope link
      
      ip -6 tunnel add name if_1_3_1 mode ip6gre \
        local 2401:db00:21:6048:feed:0::1 \
        remote 2401:db00:21:6048:feed:0::3 key 1
      ip link set dev if_1_3_1 up
      sysctl -w net.mpls.conf.if_1_3_1.input=1
      ip -4 addr add 169.254.0.4/31 dev if_1_3_1 scope link
      ```
      
      - Install MPLS encap rules on node-1 towards node-2
      
      ```
      ip route add 192.168.0.11/32 nexthop encap mpls 32/64 \
        via inet 169.254.0.3 dev if_1_2_1
      ```
      
      - Install MPLS forwarding rules on node-2 and node-3
      ```
      // node2
      ip -f mpls route add 32 via inet 169.254.0.7 dev if_2_4_1
      
      // node3
      ip -f mpls route add 64 via inet 169.254.0.12 dev if_4_3_1
      ```
      
      - Ping 192.168.0.11 (node4) from 192.168.0.1 (node1) (where routing
        towards 192.168.0.1 is via IP route directly towards node1 from node4)
      ```
      ping 192.168.0.11
      ```
      
      - tcpdump on interface to capture ping packets wrapped within MPLS
        header which inturn wrapped within IP6GRE header
      
      ```
      16:43:41.121073 IP6
        2401:db00:21:6048:feed::1 > 2401:db00:21:6048:feed::2:
        DSTOPT GREv0, key=0x1, length 100:
        MPLS (label 32, exp 0, ttl 255) (label 64, exp 0, [S], ttl 255)
        IP 192.168.0.1 > 192.168.0.11:
        ICMP echo request, id 1208, seq 45, length 64
      
      0x0000:  6000 2cdb 006c 3c3f 2401 db00 0021 6048  `.,..l<?$....!`H
      0x0010:  feed 0000 0000 0001 2401 db00 0021 6048  ........$....!`H
      0x0020:  feed 0000 0000 0002 2f00 0401 0401 0100  ......../.......
      0x0030:  2000 8847 0000 0001 0002 00ff 0004 01ff  ...G............
      0x0040:  4500 0054 3280 4000 ff01 c7cb c0a8 0001  E..T2.@.........
      0x0050:  c0a8 000b 0800 a8d7 04b8 002d 2d3c a05b  ...........--<.[
      0x0060:  0000 0000 bcd8 0100 0000 0000 1011 1213  ................
      0x0070:  1415 1617 1819 1a1b 1c1d 1e1f 2021 2223  .............!"#
      0x0080:  2425 2627 2829 2a2b 2c2d 2e2f 3031 3233  $%&'()*+,-./0123
      0x0090:  3435 3637                                4567
      ```
      Signed-off-by: default avatarSaif Hasan <has@fb.com>
      Signed-off-by: default avatarDavid S. Miller <davem@davemloft.net>
      d8e2262a
    • David S. Miller's avatar
      Merge git://git.kernel.org/pub/scm/linux/kernel/git/bpf/bpf · d2f85c9e
      David S. Miller authored
      Daniel Borkmann says:
      
      ====================
      pull-request: bpf 2018-09-24
      
      The following pull-request contains BPF updates for your *net* tree.
      
      The main changes are:
      
      1) Several fixes for BPF sockmap to only allow sockets being attached in
         ESTABLISHED state, from John.
      
      2) Fix up the license to LGPL/BSD for the libc compat header which contains
         fallback helpers that libbpf and bpftool is using, from Jakub.
      ====================
      Signed-off-by: default avatarDavid S. Miller <davem@davemloft.net>
      d2f85c9e
    • Friedemann Gerold's avatar
      net: aquantia: memory corruption on jumbo frames · d26ed6b0
      Friedemann Gerold authored
      This patch fixes skb_shared area, which will be corrupted
      upon reception of 4K jumbo packets.
      
      Originally build_skb usage purpose was to reuse page for skb to eliminate
      needs of extra fragments. But that logic does not take into account that
      skb_shared_info should be reserved at the end of skb data area.
      
      In case packet data consumes all the page (4K), skb_shinfo location
      overflows the page. As a consequence, __build_skb zeroed shinfo data above
      the allocated page, corrupting next page.
      
      The issue is rarely seen in real life because jumbo are normally larger
      than 4K and that causes another code path to trigger.
      But it 100% reproducible with simple scapy packet, like:
      
          sendp(IP(dst="192.168.100.3") / TCP(dport=443) \
                / Raw(RandString(size=(4096-40))), iface="enp1s0")
      
      Fixes: 018423e9 ("net: ethernet: aquantia: Add ring support code")
      Reported-by: default avatarFriedemann Gerold <f.gerold@b-c-s.de>
      Reported-by: default avatarMichael Rauch <michael@rauch.be>
      Signed-off-by: default avatarFriedemann Gerold <f.gerold@b-c-s.de>
      Tested-by: default avatarNikita Danilov <nikita.danilov@aquantia.com>
      Signed-off-by: default avatarIgor Russkikh <igor.russkikh@aquantia.com>
      Signed-off-by: default avatarDavid S. Miller <davem@davemloft.net>
      d26ed6b0
    • David S. Miller's avatar
      Merge branch 'netpoll-avoid-capture-effects-for-NAPI-drivers' · 841dfa43
      David S. Miller authored
      Eric Dumazet says:
      
      ====================
      netpoll: avoid capture effects for NAPI drivers
      
      As diagnosed by Song Liu, ndo_poll_controller() can
      be very dangerous on loaded hosts, since the cpu
      calling ndo_poll_controller() might steal all NAPI
      contexts (for all RX/TX queues of the NIC).
      
      This capture, showing one ksoftirqd eating all cycles
      can last for unlimited amount of time, since one
      cpu is generally not able to drain all the queues under load.
      
      It seems that all networking drivers that do use NAPI
      for their TX completions, should not provide a ndo_poll_controller() :
      
      Most NAPI drivers have netpoll support already handled
      in core networking stack, since netpoll_poll_dev()
      uses poll_napi(dev) to iterate through registered
      NAPI contexts for a device.
      
      This patch series take care of the first round, we will
      handle other drivers in future rounds.
      ====================
      Signed-off-by: default avatarDavid S. Miller <davem@davemloft.net>
      841dfa43
    • Eric Dumazet's avatar
      tun: remove ndo_poll_controller · 765cdc20
      Eric Dumazet authored
      As diagnosed by Song Liu, ndo_poll_controller() can
      be very dangerous on loaded hosts, since the cpu
      calling ndo_poll_controller() might steal all NAPI
      contexts (for all RX/TX queues of the NIC). This capture
      can last for unlimited amount of time, since one
      cpu is generally not able to drain all the queues under load.
      
      tun uses NAPI for TX completions, so we better let core
      networking stack call the napi->poll() to avoid the capture.
      Signed-off-by: default avatarEric Dumazet <edumazet@google.com>
      Signed-off-by: default avatarDavid S. Miller <davem@davemloft.net>
      765cdc20
    • Eric Dumazet's avatar
      nfp: remove ndo_poll_controller · 0825ce70
      Eric Dumazet authored
      As diagnosed by Song Liu, ndo_poll_controller() can
      be very dangerous on loaded hosts, since the cpu
      calling ndo_poll_controller() might steal all NAPI
      contexts (for all RX/TX queues of the NIC). This capture
      can last for unlimited amount of time, since one
      cpu is generally not able to drain all the queues under load.
      
      nfp uses NAPI for TX completions, so we better let core
      networking stack call the napi->poll() to avoid the capture.
      Signed-off-by: default avatarEric Dumazet <edumazet@google.com>
      Cc: Jakub Kicinski <jakub.kicinski@netronome.com>
      Acked-by: default avatarJakub Kicinski <jakub.kicinski@netronome.com>
      Tested-by: default avatarJakub Kicinski <jakub.kicinski@netronome.com>
      Signed-off-by: default avatarDavid S. Miller <davem@davemloft.net>
      0825ce70
    • Eric Dumazet's avatar
      bnxt: remove ndo_poll_controller · 58e0e22b
      Eric Dumazet authored
      As diagnosed by Song Liu, ndo_poll_controller() can
      be very dangerous on loaded hosts, since the cpu
      calling ndo_poll_controller() might steal all NAPI
      contexts (for all RX/TX queues of the NIC). This capture
      can last for unlimited amount of time, since one
      cpu is generally not able to drain all the queues under load.
      
      bnxt uses NAPI for TX completions, so we better let core
      networking stack call the napi->poll() to avoid the capture.
      Signed-off-by: default avatarEric Dumazet <edumazet@google.com>
      Cc: Michael Chan <michael.chan@broadcom.com>
      Signed-off-by: default avatarDavid S. Miller <davem@davemloft.net>
      58e0e22b
    • Eric Dumazet's avatar
      bnx2x: remove ndo_poll_controller · d8ea6a91
      Eric Dumazet authored
      As diagnosed by Song Liu, ndo_poll_controller() can
      be very dangerous on loaded hosts, since the cpu
      calling ndo_poll_controller() might steal all NAPI
      contexts (for all RX/TX queues of the NIC). This capture
      can last for unlimited amount of time, since one
      cpu is generally not able to drain all the queues under load.
      
      bnx2x uses NAPI for TX completions, so we better let core
      networking stack call the napi->poll() to avoid the capture.
      Signed-off-by: default avatarEric Dumazet <edumazet@google.com>
      Cc: Ariel Elior <ariel.elior@cavium.com>
      Signed-off-by: default avatarDavid S. Miller <davem@davemloft.net>
      d8ea6a91
    • Eric Dumazet's avatar
      mlx5: remove ndo_poll_controller · 9c29bcd1
      Eric Dumazet authored
      As diagnosed by Song Liu, ndo_poll_controller() can
      be very dangerous on loaded hosts, since the cpu
      calling ndo_poll_controller() might steal all NAPI
      contexts (for all RX/TX queues of the NIC). This capture
      can last for unlimited amount of time, since one
      cpu is generally not able to drain all the queues under load.
      
      mlx5 uses NAPI for TX completions, so we better let core
      networking stack call the napi->poll() to avoid the capture.
      Signed-off-by: default avatarEric Dumazet <edumazet@google.com>
      Cc: Saeed Mahameed <saeedm@mellanox.com>
      Signed-off-by: default avatarDavid S. Miller <davem@davemloft.net>
      9c29bcd1
    • Eric Dumazet's avatar
      mlx4: remove ndo_poll_controller · a24b66c2
      Eric Dumazet authored
      As diagnosed by Song Liu, ndo_poll_controller() can
      be very dangerous on loaded hosts, since the cpu
      calling ndo_poll_controller() might steal all NAPI
      contexts (for all RX/TX queues of the NIC). This capture
      can last for unlimited amount of time, since one
      cpu is generally not able to drain all the queues under load.
      
      mlx4 uses NAPI for TX completions, so we better let core
      networking stack call the napi->poll() to avoid the capture.
      Signed-off-by: default avatarEric Dumazet <edumazet@google.com>
      Cc: Tariq Toukan <tariqt@mellanox.com>
      Signed-off-by: default avatarDavid S. Miller <davem@davemloft.net>
      a24b66c2
    • Eric Dumazet's avatar
      i40evf: remove ndo_poll_controller · 1aa28fb9
      Eric Dumazet authored
      As diagnosed by Song Liu, ndo_poll_controller() can
      be very dangerous on loaded hosts, since the cpu
      calling ndo_poll_controller() might steal all NAPI
      contexts (for all RX/TX queues of the NIC). This capture
      can last for unlimited amount of time, since one
      cpu is generally not able to drain all the queues under load.
      
      i40evf uses NAPI for TX completions, so we better let core
      networking stack call the napi->poll() to avoid the capture.
      Signed-off-by: default avatarEric Dumazet <edumazet@google.com>
      Cc: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
      Signed-off-by: default avatarDavid S. Miller <davem@davemloft.net>
      1aa28fb9
    • Eric Dumazet's avatar
      ice: remove ndo_poll_controller · 158a08a6
      Eric Dumazet authored
      As diagnosed by Song Liu, ndo_poll_controller() can
      be very dangerous on loaded hosts, since the cpu
      calling ndo_poll_controller() might steal all NAPI
      contexts (for all RX/TX queues of the NIC). This capture
      can last for unlimited amount of time, since one
      cpu is generally not able to drain all the queues under load.
      
      ice uses NAPI for TX completions, so we better let core
      networking stack call the napi->poll() to avoid the capture.
      Signed-off-by: default avatarEric Dumazet <edumazet@google.com>
      Cc: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
      Signed-off-by: default avatarDavid S. Miller <davem@davemloft.net>
      158a08a6
    • Eric Dumazet's avatar
      igb: remove ndo_poll_controller · 0542997e
      Eric Dumazet authored
      As diagnosed by Song Liu, ndo_poll_controller() can
      be very dangerous on loaded hosts, since the cpu
      calling ndo_poll_controller() might steal all NAPI
      contexts (for all RX/TX queues of the NIC). This capture
      can last for unlimited amount of time, since one
      cpu is generally not able to drain all the queues under load.
      
      igb uses NAPI for TX completions, so we better let core
      networking stack call the napi->poll() to avoid the capture.
      Signed-off-by: default avatarEric Dumazet <edumazet@google.com>
      Cc: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
      Signed-off-by: default avatarDavid S. Miller <davem@davemloft.net>
      0542997e
    • Eric Dumazet's avatar
      ixgb: remove ndo_poll_controller · 2753166e
      Eric Dumazet authored
      As diagnosed by Song Liu, ndo_poll_controller() can
      be very dangerous on loaded hosts, since the cpu
      calling ndo_poll_controller() might steal all NAPI
      contexts (for all RX/TX queues of the NIC). This capture
      can last for unlimited amount of time, since one
      cpu is generally not able to drain all the queues under load.
      
      ixgb uses NAPI for TX completions, so we better let core
      networking stack call the napi->poll() to avoid the capture.
      
      This also removes a problematic use of disable_irq() in
      a context it is forbidden, as explained in commit
      af3e0fcf ("8139too: Use disable_irq_nosync() in
      rtl8139_poll_controller()")
      Signed-off-by: default avatarEric Dumazet <edumazet@google.com>
      Cc: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
      Signed-off-by: default avatarDavid S. Miller <davem@davemloft.net>
      2753166e
    • Eric Dumazet's avatar
      fm10k: remove ndo_poll_controller · dda9d57e
      Eric Dumazet authored
      As diagnosed by Song Liu, ndo_poll_controller() can
      be very dangerous on loaded hosts, since the cpu
      calling ndo_poll_controller() might steal all NAPI
      contexts (for all RX/TX queues of the NIC). This capture
      lasts for unlimited amount of time, since one
      cpu is generally not able to drain all the queues under load.
      
      fm10k uses NAPI for TX completions, so we better let core
      networking stack call the napi->poll() to avoid the capture.
      Signed-off-by: default avatarEric Dumazet <edumazet@google.com>
      Cc: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
      Signed-off-by: default avatarDavid S. Miller <davem@davemloft.net>
      dda9d57e
    • Eric Dumazet's avatar
      ixgbevf: remove ndo_poll_controller · 6f5d941e
      Eric Dumazet authored
      As diagnosed by Song Liu, ndo_poll_controller() can
      be very dangerous on loaded hosts, since the cpu
      calling ndo_poll_controller() might steal all NAPI
      contexts (for all RX/TX queues of the NIC). This capture
      can last for unlimited amount of time, since one
      cpu is generally not able to drain all the queues under load.
      
      ixgbevf uses NAPI for TX completions, so we better let core
      networking stack call the napi->poll() to avoid the capture.
      Signed-off-by: default avatarEric Dumazet <edumazet@google.com>
      Cc: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
      Signed-off-by: default avatarDavid S. Miller <davem@davemloft.net>
      6f5d941e
    • Eric Dumazet's avatar
      ixgbe: remove ndo_poll_controller · b80e71a9
      Eric Dumazet authored
      As diagnosed by Song Liu, ndo_poll_controller() can
      be very dangerous on loaded hosts, since the cpu
      calling ndo_poll_controller() might steal all NAPI
      contexts (for all RX/TX queues of the NIC). This capture
      can last for unlimited amount of time, since one
      cpu is generally not able to drain all the queues under load.
      
      ixgbe uses NAPI for TX completions, so we better let core
      networking stack call the napi->poll() to avoid the capture.
      Reported-by: default avatarSong Liu <songliubraving@fb.com>
      Signed-off-by: default avatarEric Dumazet <edumazet@google.com>
      Tested-by: default avatarSong Liu <songliubraving@fb.com>
      Cc: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
      Signed-off-by: default avatarDavid S. Miller <davem@davemloft.net>
      b80e71a9
    • Eric Dumazet's avatar
      bonding: use netpoll_poll_dev() helper · 93f62ad5
      Eric Dumazet authored
      We want to allow NAPI drivers to no longer provide
      ndo_poll_controller() method, as it has been proven problematic.
      
      team driver must not look at its presence, but instead call
      netpoll_poll_dev() which factorize the needed actions.
      Signed-off-by: default avatarEric Dumazet <edumazet@google.com>
      Cc: Jay Vosburgh <j.vosburgh@gmail.com>
      Cc: Veaceslav Falico <vfalico@gmail.com>
      Cc: Andy Gospodarek <andy@greyhouse.net>
      Acked-by: default avatarJay Vosburgh <jay.vosburgh@canonical.com>
      Signed-off-by: default avatarDavid S. Miller <davem@davemloft.net>
      93f62ad5
    • Eric Dumazet's avatar
      netpoll: make ndo_poll_controller() optional · ac3d9dd0
      Eric Dumazet authored
      As diagnosed by Song Liu, ndo_poll_controller() can
      be very dangerous on loaded hosts, since the cpu
      calling ndo_poll_controller() might steal all NAPI
      contexts (for all RX/TX queues of the NIC). This capture
      can last for unlimited amount of time, since one
      cpu is generally not able to drain all the queues under load.
      
      It seems that all networking drivers that do use NAPI
      for their TX completions, should not provide a ndo_poll_controller().
      
      NAPI drivers have netpoll support already handled
      in core networking stack, since netpoll_poll_dev()
      uses poll_napi(dev) to iterate through registered
      NAPI contexts for a device.
      
      This patch allows netpoll_poll_dev() to process NAPI
      contexts even for drivers not providing ndo_poll_controller(),
      allowing for following patches in NAPI drivers.
      
      Also we export netpoll_poll_dev() so that it can be called
      by bonding/team drivers in following patches.
      Reported-by: default avatarSong Liu <songliubraving@fb.com>
      Signed-off-by: default avatarEric Dumazet <edumazet@google.com>
      Tested-by: default avatarSong Liu <songliubraving@fb.com>
      Signed-off-by: default avatarDavid S. Miller <davem@davemloft.net>
      ac3d9dd0
  2. 23 Sep, 2018 2 commits
  3. 22 Sep, 2018 16 commits
  4. 21 Sep, 2018 2 commits
  5. 20 Sep, 2018 1 commit
    • Xin Long's avatar
      sctp: update dst pmtu with the correct daddr · d7ab5cdc
      Xin Long authored
      When processing pmtu update from an icmp packet, it calls .update_pmtu
      with sk instead of skb in sctp_transport_update_pmtu.
      
      However for sctp, the daddr in the transport might be different from
      inet_sock->inet_daddr or sk->sk_v6_daddr, which is used to update or
      create the route cache. The incorrect daddr will cause a different
      route cache created for the path.
      
      So before calling .update_pmtu, inet_sock->inet_daddr/sk->sk_v6_daddr
      should be updated with the daddr in the transport, and update it back
      after it's done.
      
      The issue has existed since route exceptions introduction.
      
      Fixes: 4895c771 ("ipv4: Add FIB nexthop exceptions.")
      Reported-by: ian.periam@dialogic.com
      Signed-off-by: default avatarXin Long <lucien.xin@gmail.com>
      Acked-by: default avatarMarcelo Ricardo Leitner <marcelo.leitner@gmail.com>
      Signed-off-by: default avatarDavid S. Miller <davem@davemloft.net>
      d7ab5cdc