- 13 Mar, 2015 6 commits
-
-
Wenyou Yang authored
To decrease the suspend time, move copying the sram function to the sram initialization phase, instead of every time go to suspend. In the meanwhile, substitute fncpy() for memcpy(). If there is no sram allocated for PM, the PM is not supported. Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com> Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com> Tested-by: Sylvain Rochet <sylvain.rochet@finsecur.com> Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
-
Wenyou Yang authored
To decrease the duplicated code, create the procedure to contain both activing and exiting the sdram self-refresh mode. Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com> Tested-by: Sylvain Rochet <sylvain.rochet@finsecur.com> Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
-
Sylvain Rochet authored
Assume USB PLL and PLL B are already stopped before entering sleep mode. Removed PLL B from slow clock code, all drivers are supposed to properly unprepare clocks. Signed-off-by: Sylvain Rochet <sylvain.rochet@finsecur.com> Acked-by: Wenyou.Yang <wenyou.yang@atmel.com> [nicolas.ferre@atmel.com: remove the warning printed in pm.c] Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
-
Wenyou Yang authored
The slow clock always exists, selecting CONFIG_AT91_SLOW_CLOCK config is unnecessary for the suspend to memory mode. For this mode the master clock should always switch to the slow clock. Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com> Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com> Tested-by: Sylvain Rochet <sylvain.rochet@finsecur.com> Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
-
Wenyou Yang authored
To simply the PM config the CONFIG_AT91_SLOW_CLOCK option will be removed, so move "select SRAM" from under AT91_SLOW_CLOCK, add "select SRAM if PM" under SOC_AT91SAM9 and SOC_SAMA5 Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com> Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com> Tested-by: Sylvain Rochet <sylvain.rochet@finsecur.com> Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
-
Wenyou Yang authored
The SLOWDOWN_MASTER_CLOCK definition is not used, remove the redundant code. Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com> Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com> Tested-by: Sylvain Rochet <sylvain.rochet@finsecur.com> Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
-
- 12 Mar, 2015 5 commits
-
-
Wenyou Yang authored
Since at91_pm_set_standby() will not be used out of the pm.c file, change its attribute from extern to static, remove its declaration as well. Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com> Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com> Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
-
Boris Brezillon authored
Commit 2b0ba96c ("net: phy: micrel: disable NAND-tree for KSZ8021, KSZ8031, KSZ8051, KSZ8081") automated the NAND-tree mode deactivation process, thus making this phy fixup useless. Remove it along with the associated headers inclusion. Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com> Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com> [nicolas.ferre@atmel.com: remove selection of PHYLIB in at91 Kconfig] Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
-
Nicolas Ferre authored
Third fixes batch for AT91 on 4.0: - clock fixes for USB - compatible string changes for handling USB IP differences (+ needed AHB matrix syscon) - fix of a compilation error in PM code
-
Nicolas Ferre authored
Second fixes batch for AT91 on 4.0: - little fix for !MMU debug: may also help for randconfig - fix of 2 errors in LCD clock definitions - in PM code, not writing the key leads to not execute the action
-
Nicolas Ferre authored
First fixes batch for AT91 on 4.0: - PM slowclock fixes for DDR and timeouts - fix some DT entries - little defconfig updates - the removal of a harmful watchdog option + its detailed documentation
-
- 11 Mar, 2015 4 commits
-
-
Wenyou Yang authored
When compiling the kernel in thumb2 (CONFIG_THUMB2_KERNEL option activated), we hit a compilation crash. The error message is listed below: ---8< ----- Error: cannot use register index with PC-relative addressing -- `str r0,.saved_lpr' --->8---- Add the .arm directive in the assembly files related to power management. Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com> Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
-
Nicolas Ferre authored
The UTMI clock must be selected by any high-speed USB IP. The logic behind it needs this particular clock. So, correct the clock in the device tree files affected. Reported-by: Bo Shen <voice.shen@atmel.com> Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com> Cc: <stable@vger.kernel.org> #3.18
-
Boris Brezillon authored
The at91rm9200, at91sam9260, at91sam9261 and at91sam9263 SoCs have slightly different UDC IPs. Those differences were previously handled with cpu_is_at91xx macro which are about to be dropped for multi-platform support, thus we need to change compatible strings. Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com> Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
-
Boris Brezillon authored
There is no specific driver handling the AHB matrix, this is a simple syscon device. the matrix is needed by several other drivers including the USB on some SoCs (at91sam9261 for instance). Without this definition, the USB will not work on these SoCs. Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com> Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
-
- 09 Mar, 2015 1 commit
-
-
Boris Brezillon authored
Peripheral clock is named pclk and system clock is named hclk (those are the names expected by the at91_udc driver). Drop the deprecated usb_clk (formerly used to configure the usb clock rate which is now directly configurable through hclk). Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com> Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
-
- 05 Mar, 2015 4 commits
-
-
Patrice Vilchez authored
Because writing the MOR register requires the PASSWD(0x37), if missed, the write operation will be aborted. Signed-off-by: Patrice Vilchez <patrice.vilchez@atmel.com> Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com> Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
-
Boris BREZILLON authored
lcdck takes mck (not smd) as its parent. It is also assigned id 3 and not 4. Signed-off-by: Boris BREZILLON <boris.brezillon@free-electrons.com> [nicolas.ferre@atmel.com: squashed 2 related patches] Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
-
Boris BREZILLON authored
Rename lcd_clk into lcdc_clk to be consistent with sama5d3 clock definitions. Signed-off-by: Boris BREZILLON <boris.brezillon@free-electrons.com> Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
-
Alexandre Belloni authored
Linux may be used without MMU on atmel SoCs, fix debug in this configuration. Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com> Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
-
- 04 Mar, 2015 5 commits
-
-
Michel Marti authored
Since turning on idle-halt in commit fe46aa67 (ARM: at91/dt: add sam9 watchdog default options to SoCs), SoCs compatible with at91sam9260-wdt no longer reboot if the watchdog times out while the CPU is in idle state. Removing the 'idle-halt' flag that was set by default fixes this. Signed-off-by: Michel Marti <mma@objectxp.com> Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com> Acked-by: Sylvain Rochet <sylvain.rochet@finsecur.com> [nicolas.ferre@atmel.com: rework the commit message] Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
-
Sylvain Rochet authored
atmel,idle-halt property should be used with care, it actually makes the watchdog not counting when the CPU is in idle state, therefore the watchdog reset time depends on mean CPU usage and will not reset at all of the CPU stop working while it is in idle state, which is probably not what you want. Signed-off-by: Sylvain Rochet <sylvain.rochet@finsecur.com> Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com> Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
-
Alexandre Belloni authored
There is now only one defconfig for the at91rm9200 and at91sam9. Add ethernet support for the at91rm9200. Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com> Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
-
Anthony Harivel authored
Recent distributions and userspace tools after 2009/2010 depend on the existence of /sys/class/block/, and will not work with this option enabled. Signed-off-by: Anthony Harivel <anthony.harivel@emtrion.de> Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
-
Jonas Andersson authored
Corrected pins used by usart3. Signed-off-by: Jonas Andersson <jonas@microbit.se> Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com> Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
-
- 03 Mar, 2015 8 commits
-
-
Nicolas Ferre authored
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
-
Alexander Stein authored
Commit ff04660e48b20 ("ARM: at91/dt: add SRAM nodes") used the same base address for sram0 and sram1 leading to the following warning: WARNING: CPU: 0 PID: 1 at fs/sysfs/dir.c:31 sysfs_warn_dup+0x50/0x70() sysfs: cannot create duplicate filename '/devices/platform/300000.sram' Fix the base address for sram1. Signed-off-by: Alexander Stein <alexanders83@web.de> Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com> Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
-
Alexandre Belloni authored
On some platforms, there are multiple SRAM nodes defined in the device tree but some of them are disabled, leading to allocation failure. Try to find the first enabled SRAM node and allocate from it. Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com> Tested-by: Wenyou Yang <wenyou.yang@atmel.com> Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
-
Alexandre Belloni authored
at91rm9200 standby and suspend to ram has been broken since 00482a40. It is wrongly using AT91_BASE_SYS which is a physical address and actually doesn't correspond to any register on at91rm9200. Use the correct at91_ramc_base[0] instead. Fixes: 00482a40 (ARM: at91: implement the standby function for pm/cpuidle) Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com> Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
-
Peter Rosin authored
The DDRSDR controller fails miserably to put LPDDR1 memories in self-refresh. Force the controller to think it has DDR2 memories during the self-refresh period, as the DDR2 self-refresh spec is equivalent to LPDDR1, and is correctly implemented in the controller. Assume that the second controller has the same fault, but that is untested. Signed-off-by: Peter Rosin <peda@axentia.se> Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com> Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
-
Sylvain Rochet authored
Removed timeout on XTAL, PLL lock and Master Clock Ready, hang if something went wrong instead of continuing in unknown condition. There is not much we can do if a PLL lock never ends, we are running in SRAM and we will not be able to connect back the sdram or ddram in order to be able to fire up a message or just panic. As a bonus, not decounting the timeout register in slow clock mode reduce cumulated suspend time and resume time from ~17ms to ~15ms. Signed-off-by: Sylvain Rochet <sylvain.rochet@finsecur.com> Acked-by: Wenyou.Yang <wenyou.yang@atmel.com> Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
-
Linus Torvalds authored
-
Daniel Vetter authored
This is a tricky story of the new atomic state handling and the legacy code fighting over each another. The bug at hand is an underrun of the framebuffer reference with subsequent hilarity caused by the load detect code. Which is peculiar since the the exact same code works fine as the implementation of the legacy setcrtc ioctl. Let's look at the ingredients: - Currently our code is a crazy mix of legacy modeset interfaces to set the parameters and half-baked atomic state tracking underneath. While this transition is going we're using the transitional plane helpers to update the atomic side (drm_plane_helper_disable/update and friends), i.e. plane->state->fb. Since the state structure owns the fb those functions take care of that themselves. The legacy state (specifically crtc->primary->fb) is still managed by the old code (and mostly by the drm core), with the fb reference counting done by callers (core drm for the ioctl or the i915 load detect code). The relevant commit is commit ea2c67bb Author: Matt Roper <matthew.d.roper@intel.com> Date: Tue Dec 23 10:41:52 2014 -0800 drm/i915: Move to atomic plane helpers (v9) - drm_plane_helper_disable has special code to handle multiple calls in a row - it checks plane->crtc == NULL and bails out. This is to match the proper atomic implementation which needs the crtc to get at the implied locking context atomic updates always need. See commit acf24a39 Author: Daniel Vetter <daniel.vetter@ffwll.ch> Date: Tue Jul 29 15:33:05 2014 +0200 drm/plane-helper: transitional atomic plane helpers - The universal plane code split out the implicit primary plane from the CRTC into it's own full-blown drm_plane object. As part of that the setcrtc ioctl (which updated both the crtc mode and primary plane) learned to set crtc->primary->crtc on modeset to make sure the plane->crtc assignments statate up to date in commit e13161af Author: Matt Roper <matthew.d.roper@intel.com> Date: Tue Apr 1 15:22:38 2014 -0700 drm: Add drm_crtc_init_with_planes() (v2) Unfortunately we've forgotten to update the load detect code. Which wasn't a problem since the load detect modeset is temporary and always undone before we drop the locks. - Finally there is a organically grown history (i.e. don't ask) around who sets the legacy plane->fb for the various driver entry points. Originally updating that was the drivers duty, but for almost all places we've moved that (plus updating the refcounts) into the core. Again the exception is the load detect code. Taking all together the following happens: - The load detect code doesn't set crtc->primary->crtc. This is only really an issue on crtcs never before used or when userspace explicitly disabled the primary plane. - The plane helper glue code short-circuits because of that and leaves a non-NULL fb behind in plane->state->fb and plane->fb. The state fb isn't a real problem (it's properly refcounted on its own), it's just the canary. - Load detect code drops the reference for that fb, but doesn't set plane->fb = NULL. This is ok since it's still living in that old world where drivers had to clear the pointer but the core/callers handled the refcounting. - On the next modeset the drm core notices plane->fb and takes care of refcounting it properly by doing another unref. This drops the refcount to zero, leaving state->plane now pointing at freed memory. - intel_plane_duplicate_state still assume it owns a reference to that very state->fb and bad things start to happen. Fix this all by applying the same duct-tape as for the legacy setcrtc ioctl code and set crtc->primary->crtc properly. Cc: Matt Roper <matthew.d.roper@intel.com> Cc: Paul Bolle <pebolle@tiscali.nl> Cc: Rob Clark <robdclark@gmail.com> Cc: Paulo Zanoni <przanoni@gmail.com> Cc: Sean Paul <seanpaul@chromium.org> Cc: Matt Roper <matthew.d.roper@intel.com> Reported-and-tested-by: Linus Torvalds <torvalds@linux-foundation.org> Reported-by: Paul Bolle <pebolle@tiscali.nl> Signed-off-by: Daniel Vetter <daniel.vetter@intel.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
-
- 02 Mar, 2015 4 commits
-
-
git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpioLinus Torvalds authored
Pull GPIO fixes from Linus Walleij: "Two GPIO fixes: - Fix a translation problem in of_get_named_gpiod_flags() - Fix a long standing container_of() mistake in the TPS65912 driver" * tag 'gpio-v4.0-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: gpio: tps65912: fix wrong container_of arguments gpiolib: of: allow of_gpiochip_find_and_xlate to find more than one chip per node
-
Linus Torvalds authored
Merge branch 'fixes-for-4.0-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/evalenti/linux-soc-thermal Pull thermal management fixes from Eduardo Valentin: "Specifics: - Several fixes in tmon tool. - Fixes in intel int340x for _ART and _TRT tables. - Add id for Avoton SoC into powerclamp driver. - Fixes in RCAR thermal driver to remove race conditions and fix fail path - Fixes in TI thermal driver: removal of unnecessary code and build fix if !CONFIG_PM_SLEEP - Cleanups in exynos thermal driver - Add stubs for include/linux/thermal.h. Now drivers using thermal calls but that also work without CONFIG_THERMAL will be able to compile for systems that don't care about thermal. Note: I am sending this pull on Rui's behalf while he fixes issues in his Linux box" * 'fixes-for-4.0-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/evalenti/linux-soc-thermal: thermal: int340x_thermal: Ignore missing _ART, _TRT tables thermal/intel_powerclamp: add id for Avoton SoC tools/thermal: tmon: silence 'set but not used' warnings tools/thermal: tmon: use pkg-config to determine library dependencies tools/thermal: tmon: support cross-compiling tools/thermal: tmon: add .gitignore tools/thermal: tmon: fixup tui windowing calculations tools/thermal: tmon: tui: don't hard-code dialog window size assumptions tools/thermal: tmon: add min/max macros tools/thermal: tmon: add --target-temp parameter thermal: exynos: Clean-up code to use oneline entry for exynos compatible table thermal: rcar: Make error and remove paths symmetrical with init thermal: rcar: Fix race condition between init and interrupt thermal: Introduce dummy functions when thermal is not defined ti-soc-thermal: Delete an unnecessary check before the function call "cpufreq_cooling_unregister" thermal: ti-soc-thermal: bandgap: Fix build warning if !CONFIG_PM_SLEEP
-
git://neil.brown.name/mdLinus Torvalds authored
Pull md fixes from Neil Brown: "Three md fixes: - fix a read-balance problem that was reported 2 years ago, but that I never noticed the report :-( - fix for rare RAID6 problem causing incorrect bitmap updates when two devices fail. - add __ATTR_PREALLOC annotation now that it is possible" * tag 'md/4.0-fixes' of git://neil.brown.name/md: md: mark some attributes as pre-alloc raid5: check faulty flag for array status during recovery. md/raid1: fix read balance when a drive is write-mostly.
-
git://git.kernel.org/pub/scm/linux/kernel/git/jhogan/metagLinus Torvalds authored
Pull arch/metag fix from James Hogan: "This is just a single patch to fix the KSTK_EIP() and KSTK_ESP() macros for metag which have always been erronously returning the PC and stack pointer of the task's kernel context rather than from its user context saved at entry from userland into the kernel, which affects the contents of /proc/<pid>/maps and /proc/<pid>/stat" * tag 'metag-fixes-v4.0-1' of git://git.kernel.org/pub/scm/linux/kernel/git/jhogan/metag: metag: Fix KSTK_EIP() and KSTK_ESP() macros
-
- 01 Mar, 2015 3 commits
-
-
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tipLinus Torvalds authored
Pull x86 fixes from Ingo Molnar: "A CR4-shadow 32-bit init fix, plus two typo fixes" * 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: x86: Init per-cpu shadow copy of CR4 on 32-bit CPUs too x86/platform/intel-mid: Fix trivial printk message typo in intel_mid_arch_setup() x86/cpu/intel: Fix trivial typo in intel_tlb_table[]
-
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tipLinus Torvalds authored
Pull timer fixes from Ingo Molnar: "Three clockevents/clocksource driver fixes" * 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: clocksource: pxa: Fix section mismatch clocksource: mtk: Fix race conditions in probe code clockevents: asm9260: Fix compilation error with sparc/sparc64 allyesconfig
-
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tipLinus Torvalds authored
Pull perf fixes from Ingo Molnar: "Two kprobes fixes and a handful of tooling fixes" * 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: perf tools: Make sparc64 arch point to sparc perf symbols: Define EM_AARCH64 for older OSes perf top: Fix SIGBUS on sparc64 perf tools: Fix probing for PERF_FLAG_FD_CLOEXEC flag perf tools: Fix pthread_attr_setaffinity_np build error perf tools: Define _GNU_SOURCE on pthread_attr_setaffinity_np feature check perf bench: Fix order of arguments to memcpy_alloc_mem kprobes/x86: Check for invalid ftrace location in __recover_probed_insn() kprobes/x86: Use 5-byte NOP when the code might be modified by ftrace
-