The valid tx/rx antenna information is part of EEPROM, so use it
to configure the device.

For few cases, the EEPROM did not reflect the correct antenna, but
it is too late to modify the EEPROM, so overwrite with .cfg parameters
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>

was not used, remove it
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>

It is no longer used anywhere
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Categorize AR7010 & AR9287 devices based on driver_info
of usb_device_id, instead of PIDs. This avoids per-device cases
and minimize code changes for new device addition.
Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

AR9287 devices (PCI/USB) use different eeprom start location
to read nvram. New devices might endup with same devid. So use
driver_info to set offset, instead of devid. driver_info is
valid for HTC devices alone which is filled in usb_device_id.
Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Added driver_info to identify AR7010, R9287 HTC devices.
Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

The driver_info stores the device category information which
is used to load appropriate device firmware, select firmware offset
and eeprom starting location. The driver_info is accessed across
ath9k_htc and ath9k_hw. Hence placed under common structure.
Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

For 6000g2b and up, adding advance power management support
for better power consumption
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

If shadow register is enable, modify the power management
command to inform uCode
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Check the BT PSPoll flag when fill PM command to uCode
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Adding additional power management option available for the device.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Bit 7 of BT config flag is used to enable/disable PSPoll sync.
Make the name to match it.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

For drivers that have accurate TX status reporting
we can report the number of consecutive lost packets
to userspace using the new cfg80211 CQM event. The
threshold is fixed right now, this may need to be
improved in the future.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This adds the ability for drivers to use CQM events
to notify about packet loss for specific stations
(which could be the AP for the managed mode case).
Since the threshold might be determined by the
driver (it isn't passed in right now) it will be
passed out of the driver to userspace in the event.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Signed-off-by: Bruno Randolf <br1@einfach.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This should help with latency issues which can happen when
using aggregation.

Cc: Felix Fietkau <nbd@openwrt.org>
Cc: Matt Smith <matt.smith@atheros.com>
Cc: Senthil Balasubramanian <senthilkumar@atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This should help with latency issues which can happen when
using aggregation.

Cc: Matt Smith <matt.smith@atheros.com>
Cc: Senthil Balasubramanian <senthilkumar@atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Since nullfunc frames are transmitted as unicast frames, they're more
reliable than the broadcast probe requests, so we need fewer retries
to figure out whether the AP is really gone.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

nullfunc frames are better for connection monitoring, because probe requests
are answered even if the AP has already dropped the connection, whereas
nullfunc frames from an unassociated station will trigger a disassoc/deauth
frame from the AP (WLAN_REASON_CLASS3_FRAME_FROM_NONASSOC_STA), which allows
the station to reconnect immediately instead of waiting until it attempts to
transmit the next unicast frame.

This only works on hardware with reliable tx ACK reporting, any other hardware
needs to fall back to the probe request method.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

- store the multicast rate as an index instead of the rate value
  (reduces cpu overhead in a hotpath)
- validate the rate values (must match a bitrate in at least one sband)
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Check the connection by probing the AP (either using nullfunc or a
probe request). If nullfunc probing is supported and the assoc is no
longer valid, the AP will send a disassoc/deauth immediately.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Instead of using a fixed 2 second timeout, calculate beacon loss interval
from the advertised beacon interval and a frame count.  With this beacon
loss happens after N (default 7) consecutive frames are missed which
for a typical setup (100TU beacon interval) is ~700ms (or ~1/3 previous).
Signed-off-by: Sam Leffler <sleffler@chromium.org>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Signed-off-by: Paul Stewart <pstew@google.com>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Remove some typos, warnings, initialize some values to follow wl's code path.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Additional comment by Larry Finger <Larry.Finger@lwfinger.net>:

This change deserves a bit more explanation. You might include something like
"These tables came from reverse engineering the 5.10.56.46 version of the
Broadcom driver. Trace comparisons between b43 and the current Broadcom driver
(5.10.120.0) show byte reversals for the PHY register writes."
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

No change in output for pr_<level> prefixes.
netdev_<level> output is different, arguably improved.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This reverts commit 86107fd1.

This patch inadvertantly changed the userland ABI.
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Fix unbalanced call to sdio_release_host() on the error path.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>

wireless-testing commit a05b5d45
ath9k: add support for reading eeprom from platform data on PCI devices

This change moved the initialization of the AH_USE_EEPROM flag from ath9k_hw
to ath9k. This needs to be added to ath9k_htc as well
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Under load, a large number of frames can produce decryption errors, even when
no key cache update is being done. Performing a key search for every single
frame in an A-MPDU improves reliability.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Mark arrays const that are unmodified after initializations.

   text	   data	    bss	    dec	    hex	filename
  19291	     56	   4136	  23483	   5bbb	drivers/net/wireless/zd1211rw/zd_chip.o.old
  19291	     56	   4136	  23483	   5bbb	drivers/net/wireless/zd1211rw/zd_chip.o.new
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Using static const generally increases object text and decreases data size.
It also generally decreases overall object size.

   text	   data	    bss	    dec	    hex	filename
  40197	     56	   8336	  48589	   bdcd	drivers/net/wireless/rt2x00/rt2800lib.o.new
  40205	     56	   8336	  48597	   bdd5	drivers/net/wireless/rt2x00/rt2800lib.o.old
Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Using static const generally increases object text and decreases data size.
It also generally decreases overall object size.

   text	   data	    bss	    dec	    hex	filename
  41757	   2205	   9896	  53858	   d262	drivers/net/wireless/rndis_wlan.o.old
  41653	   2205	   9880	  53738	   d1ea	drivers/net/wireless/rndis_wlan.o.new

Changed functions rndis_set_oid and set_bssid to take const *'s.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Using static const generally increases object text and decreases data size.
It also generally decreases overall object size.

   text	   data	    bss	    dec	    hex	filename
  42607	   3581	   8536	  54724	   d5c4	drivers/net/wireless/ray_cs.o.new
  42603	   3585	   8536	  54724	   d5c4	drivers/net/wireless/ray_cs.o.old
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>