CONFIG_OF_DYNAMIC and CONFIG_ACPI allow adding SPI devices at runtime
using a DeviceTree overlay or DSDT patch.  CONFIG_SPI_SLAVE allows the
same via sysfs.

But there are no precautions to prevent adding a device below a
controller that's being removed.  Such a device is unusable and may not
even be able to unbind cleanly as it becomes inaccessible once the
controller has been torn down.  E.g. it is then impossible to quiesce
the device's interrupt.

of_spi_notify() and acpi_spi_notify() do hold a ref on the controller,
but otherwise run lockless against spi_unregister_controller().

Fix by holding the spi_add_lock in spi_unregister_controller() and
bailing out of spi_add_device() if the controller has been unregistered
concurrently.

Fixes: ce79d54a ("spi/of: Add OF notifier handler")
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Cc: stable@vger.kernel.org # v3.19+
Cc: Geert Uytterhoeven <geert+renesas@glider.be>
Cc: Octavian Purdila <octavian.purdila@intel.com>
Cc: Pantelis Antoniou <pantelis.antoniou@konsulko.com>
Link: https://lore.kernel.org/r/a8c3205088a969dc8410eec1eba9aface60f36af.1596451035.git.lukas@wunner.deSigned-off-by: Mark Brown <broonie@kernel.org>

Hi,

This patchset mainly fixes some recently discovered problems about CS for
LPSPI module on i.MX8DXLEVK.

Add the dt-bindings description for the new property.

Clark Wang (4):
  spi: lpspi: Fix kernel warning dump when probe fail after calling
    spi_register
  spi: lpspi: remove unused fsl_lpspi->chipselect
  spi: lpspi: fix using CS discontinuously on i.MX8DXLEVK
  dt-bindings: lpspi: New property in document DT bindings for LPSPI

 .../bindings/spi/spi-fsl-lpspi.yaml           |  7 ++++++
 drivers/spi/spi-fsl-lpspi.c                   | 25 +++++++++++--------
 2 files changed, 21 insertions(+), 11 deletions(-)

--
2.17.1

Add "fsl,spi-only-use-cs1-sel" to fit i.MX8DXL-EVK.
Spi common code does not support use of CS signals discontinuously.
It only uses CS1 without using CS0. So, add this property to re-config
chipselect value.
Signed-off-by: Clark Wang <xiaoning.wang@nxp.com>
Link: https://lore.kernel.org/r/20200727031513.31774-1-xiaoning.wang@nxp.comSigned-off-by: Mark Brown <broonie@kernel.org>

SPI common code does not support using CS discontinuously for now.
However, i.MX8DXL-EVK only uses CS1 without CS0. Therefore, add a flag
is_only_cs1 to set the correct TCR[PCS].
Signed-off-by: Clark Wang <xiaoning.wang@nxp.com>
Link: https://lore.kernel.org/r/20200727031448.31661-4-xiaoning.wang@nxp.comSigned-off-by: Mark Brown <broonie@kernel.org>

The cs-gpio is initailized by spi_get_gpio_descs() now. Remove the
chipselect.
Signed-off-by: Clark Wang <xiaoning.wang@nxp.com>
Link: https://lore.kernel.org/r/20200727031448.31661-3-xiaoning.wang@nxp.comSigned-off-by: Mark Brown <broonie@kernel.org>

Calling devm_spi_register_controller() too early will cause problem.
When probe failed occurs after calling devm_spi_register_controller(),
the call of spi_controller_put() will trigger the following warning dump.

[    2.092138] ------------[ cut here ]------------
[    2.096876] kernfs: can not remove 'uevent', no directory
[    2.102440] WARNING: CPU: 0 PID: 181 at fs/kernfs/dir.c:1503 kernfs_remove_by_name_ns+0xa0/0xb0
[    2.111142] Modules linked in:
[    2.114207] CPU: 0 PID: 181 Comm: kworker/0:7 Not tainted 5.4.24-05024-g775c6e8a738c-dirty #1314
[    2.122991] Hardware name: Freescale i.MX8DXL EVK (DT)
[    2.128141] Workqueue: events deferred_probe_work_func
[    2.133281] pstate: 60000005 (nZCv daif -PAN -UAO)
[    2.138076] pc : kernfs_remove_by_name_ns+0xa0/0xb0
[    2.142958] lr : kernfs_remove_by_name_ns+0xa0/0xb0
[    2.147837] sp : ffff8000122bba70
[    2.151145] x29: ffff8000122bba70 x28: ffff8000119d6000
[    2.156462] x27: 0000000000000000 x26: ffff800011edbce8
[    2.161779] x25: 0000000000000000 x24: ffff00003ae4f700
[    2.167096] x23: ffff000010184c10 x22: ffff00003a3d6200
[    2.172412] x21: ffff800011a464a8 x20: ffff000010126a68
[    2.177729] x19: ffff00003ae5c800 x18: 000000000000000e
[    2.183046] x17: 0000000000000001 x16: 0000000000000019
[    2.188362] x15: 0000000000000004 x14: 000000000000004c
[    2.193679] x13: 0000000000000000 x12: 0000000000000001
[    2.198996] x11: 0000000000000000 x10: 00000000000009c0
[    2.204313] x9 : ffff8000122bb7a0 x8 : ffff00003a3d6c20
[    2.209630] x7 : ffff00003a3d6380 x6 : 0000000000000001
[    2.214946] x5 : 0000000000000001 x4 : ffff00003a05eb18
[    2.220263] x3 : 0000000000000005 x2 : ffff8000119f1c48
[    2.225580] x1 : 2bcbda323bf5a800 x0 : 0000000000000000
[    2.230898] Call trace:
[    2.233345]  kernfs_remove_by_name_ns+0xa0/0xb0
[    2.237879]  sysfs_remove_file_ns+0x14/0x20
[    2.242065]  device_del+0x12c/0x348
[    2.245555]  device_unregister+0x14/0x30
[    2.249492]  spi_unregister_controller+0xac/0x120
[    2.254201]  devm_spi_unregister+0x10/0x18
[    2.258304]  release_nodes+0x1a8/0x220
[    2.262055]  devres_release_all+0x34/0x58
[    2.266069]  really_probe+0x1b8/0x318
[    2.269733]  driver_probe_device+0x54/0xe8
[    2.273833]  __device_attach_driver+0x80/0xb8
[    2.278194]  bus_for_each_drv+0x74/0xc0
[    2.282034]  __device_attach+0xdc/0x138
[    2.285876]  device_initial_probe+0x10/0x18
[    2.290063]  bus_probe_device+0x90/0x98
[    2.293901]  deferred_probe_work_func+0x64/0x98
[    2.298442]  process_one_work+0x198/0x320
[    2.302451]  worker_thread+0x1f0/0x420
[    2.306208]  kthread+0xf0/0x120
[    2.309352]  ret_from_fork+0x10/0x18
[    2.312927] ---[ end trace 58abcdfae01bd3c7 ]---

So put this function at the end of the probe sequence.
Signed-off-by: Clark Wang <xiaoning.wang@nxp.com>
Link: https://lore.kernel.org/r/20200727031448.31661-2-xiaoning.wang@nxp.comSigned-off-by: Mark Brown <broonie@kernel.org>

The RXFLR is possible larger than rx_left in Rockchip SPI, fix it.

Fixes: 01b59ce5 ("spi: rockchip: use irq rather than polling")
Signed-off-by: Jon Lin <jon.lin@rock-chips.com>
Tested-by: Emil Renner Berthing <kernel@esmil.dk>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Emil Renner Berthing <kernel@esmil.dk>
Link: https://lore.kernel.org/r/20200723004356.6390-3-jon.lin@rock-chips.comSigned-off-by: Mark Brown <broonie@kernel.org>

The FIFO depth of SPI V2 is 64 instead of 32, add support for it.
Signed-off-by: Jon Lin <jon.lin@rock-chips.com>
Tested-by: Emil Renner Berthing <kernel@esmil.dk>
Reviewed-by: Emil Renner Berthing <kernel@esmil.dk>
Link: https://lore.kernel.org/r/20200723004356.6390-2-jon.lin@rock-chips.comSigned-off-by: Mark Brown <broonie@kernel.org>

The burst length can be adjusted according to the transmission
length to improve the transmission rate
Signed-off-by: Jon Lin <jon.lin@rock-chips.com>
Tested-by: Emil Renner Berthing <kernel@esmil.dk>
Reviewed-by: Emil Renner Berthing <kernel@esmil.dk>
Link: https://lore.kernel.org/r/20200723004356.6390-1-jon.lin@rock-chips.comSigned-off-by: Mark Brown <broonie@kernel.org>

Before generic upgrade, both .suspend() and .resume() were invoking
pci_enable_wake(pci_dev, PCI_D3hot, 0). Hence, disabling wakeup in both
states. (Normal trend is .suspend() enables and .resume() disables the
wakeup.)

This was ambiguous and may be buggy. Instead of replicating the legacy
behavior, drop the wakeup-disable call.

Fixes: f185bcc7 ("spi: spi-topcliff-pch: use generic power management")
Reported-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Vaibhav Gupta <vaibhavgupta40@gmail.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/r/20200727172936.661567-1-vaibhavgupta40@gmail.comSigned-off-by: Mark Brown <broonie@kernel.org>

Simply copying all xfers from userspace into one bounce buffer causes
alignment problems if the SPI controller uses DMA.

Ensure that all transfer data blocks within the rx and tx bounce buffers
are aligned for DMA (according to ARCH_KMALLOC_MINALIGN).

Alignment may increase the usage of the bounce buffers. In some cases,
the buffers may need to be increased using the "bufsiz" module
parameter.
Signed-off-by: Christian Eggers <ceggers@arri.de>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20200728100832.24788-1-ceggers@arri.deSigned-off-by: Mark Brown <broonie@kernel.org>

Silence documentation build warnings by correcting kernel-doc comment
for spi_transfer struct.
Signed-off-by: Colton Lewis <colton.w.lewis@protonmail.com>
Link: https://lore.kernel.org/r/20200725050242.279548-1-colton.w.lewis@protonmail.comSigned-off-by: Mark Brown <broonie@kernel.org>

The spi-sun4i driver already has the ability to do large transfers.
However, the max transfer size reported is still fifo depth - 1.

Update the max transfer size reported to the max value possible.

Fixes: 19673791 ("spi: sun4i: Allow transfers larger than FIFO size")
Signed-off-by: Jonathan Liu <net147@gmail.com>
Acked-by: Maxime Ripard <mripard@kernel.org>
Link: https://lore.kernel.org/r/20200727072328.510798-1-net147@gmail.comSigned-off-by: Mark Brown <broonie@kernel.org>

Enable runtime pm support for spi-imx driver.
Signed-off-by: Clark Wang <xiaoning.wang@nxp.com>
Link: https://lore.kernel.org/r/20200727063354.17031-1-xiaoning.wang@nxp.comSigned-off-by: Mark Brown <broonie@kernel.org>

Add a DT binding documentation for the MT8192 soc.
Signed-off-by: leilk.liu <leilk.liu@mediatek.com>
Link: https://lore.kernel.org/r/20200721122436.31544-1-leilk.liu@mediatek.comSigned-off-by: Mark Brown <broonie@kernel.org>

This patch add spi support for mt8192 IC.
Signed-off-by: leilk.liu <leilk.liu@mediatek.com>
Link: https://lore.kernel.org/r/20200721122436.31544-2-leilk.liu@mediatek.comSigned-off-by: Mark Brown <broonie@kernel.org>

Add support to SPI controller on Intel Atom based Lightning Mountain
SoC which reuses the Lantiq SPI controller IP.
Signed-off-by: Dilip Kota <eswara.kota@linux.intel.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/7d644e5d03ef534f719763e5c823c1673e53d1a5.1594957019.git.eswara.kota@linux.intel.comSigned-off-by: Mark Brown <broonie@kernel.org>

Add support to SPI controller on Intel Atom based Lightning Mountain SoC
which reuses Lantiq SPI controller IP.
Signed-off-by: Dilip Kota <eswara.kota@linux.intel.com>
Link: https://lore.kernel.org/r/4d61a75381aca9479f9fc15d07a7b05534da6bb3.1594957019.git.eswara.kota@linux.intel.comSigned-off-by: Mark Brown <broonie@kernel.org>

Moving interrupt configuration to SoC specific data structure helps to add
support for newer SoCs on which SPI controller with lesser interrupt lines
compared to existing chipsets.
Signed-off-by: Dilip Kota <eswara.kota@linux.intel.com>
Link: https://lore.kernel.org/r/7eb6d863515245fedfa0296c72082df107367d07.1594957019.git.eswara.kota@linux.intel.comSigned-off-by: Mark Brown <broonie@kernel.org>

On newer chipsets, SPI controller has fifos of larger size.
So add the fifo size bit mask entry in SoC specific data structure.
Signed-off-by: Dilip Kota <eswara.kota@linux.intel.com>
Link: https://lore.kernel.org/r/a0889abf17a9fbc7077f10be0f0342b7ebdf9361.1594957019.git.eswara.kota@linux.intel.comSigned-off-by: Mark Brown <broonie@kernel.org>

On newer chipsets interrupt need to be acknowledged as they use
different interrupt controller which does not acknowledge the
interrupts automatically.
Signed-off-by: Dilip Kota <eswara.kota@linux.intel.com>
Link: https://lore.kernel.org/r/608923b484d9ef239b44bb545c0b79b27030a6ae.1594957019.git.eswara.kota@linux.intel.comSigned-off-by: Mark Brown <broonie@kernel.org>

Address of Interrupt control registers are different on new chipsets.
So move them to SoC specific data structure.
Signed-off-by: Dilip Kota <eswara.kota@linux.intel.com>
Link: https://lore.kernel.org/r/f0f9723a30ea9c2ee48d2199f7512af9e15803b0.1594957019.git.eswara.kota@linux.intel.comSigned-off-by: Mark Brown <broonie@kernel.org>

Existing driver supports only single core SoC. New multicore platforms uses
the same driver/IP so SMP support is required. This patch adds multicore
support in the driver.
Signed-off-by: Dilip Kota <eswara.kota@linux.intel.com>
Link: https://lore.kernel.org/r/d6663296b41f102c582fda08e71f62b72ca05d5d.1594957019.git.eswara.kota@linux.intel.comSigned-off-by: Mark Brown <broonie@kernel.org>

In full duplex mode, rx overflow error is observed. To overcome the error,
wait until the complete data got received and proceed further.

Fixes: 17f84b79 ("spi: lantiq-ssc: add support for Lantiq SSC SPI controller")
Signed-off-by: Dilip Kota <eswara.kota@linux.intel.com>
Link: https://lore.kernel.org/r/efb650b0faa49a00788c4e0ca8ef7196bdba851d.1594957019.git.eswara.kota@linux.intel.comSigned-off-by: Mark Brown <broonie@kernel.org>

Drivers using legacy PM have to manage PCI states and device's PM states
themselves. They also need to take care of configuration registers.

With improved and powerful support of generic PM, PCI Core takes care of
above mentioned, device-independent, jobs.

This driver makes use of PCI helper functions like
pci_save/restore_state(), pci_enable/disable_device(), pci_enable_wake()
and pci_set_power_state() to do required operations. In generic mode, they
are no longer needed.

Change function parameter in both .suspend() and .resume() to
"struct device*" type. Use dev_get_drvdata() to get drv data.

Compile-tested only.
Signed-off-by: Vaibhav Gupta <vaibhavgupta40@gmail.com>
Link: https://lore.kernel.org/r/20200720155714.714114-1-vaibhavgupta40@gmail.comSigned-off-by: Mark Brown <broonie@kernel.org>

This converts the PPC4xx SPI driver to use GPIO descriptors.

The driver is already just picking some GPIOs from the device
tree so the conversion is pretty straight forward. However
this driver is looking form a pure "gpios" property rather
than the standard binding "cs-gpios" so we need to add a new
exception to the gpiolib OF parser to allow this for this
driver's compatibles.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Cc: linuxppc-dev@lists.ozlabs.org
Link: https://lore.kernel.org/r/20200714072226.26071-1-linus.walleij@linaro.orgSigned-off-by: Mark Brown <broonie@kernel.org>

The spi cadence driver should support spi-cs-high in mode bits
so that the peripherals that needs the chip select to be high active can
use it. Add the SPI-CS-HIGH flag in the supported mode bits.
Signed-off-by: Shreyas Joshi <shreyas.joshi@biamp.com>
Link: https://lore.kernel.org/r/20200710211655.1564-1-shreyas.joshi@biamp.comSigned-off-by: Mark Brown <broonie@kernel.org>

Call the put function after probe successfully. Otherwise, the lpspi
module will keep active status until the first spi transfer called.

Disable runtime pm when probe fails. There is no need to active runtime
pm after probe failed.
Signed-off-by: Clark Wang <xiaoning.wang@nxp.com>
Link: https://lore.kernel.org/r/20200714075251.12777-2-xiaoning.wang@nxp.comSigned-off-by: Mark Brown <broonie@kernel.org>

Merge series "Add support for [H]SCIF/TMU/CMT/THS/SDHI/MSIOF/CAN[FD]/I2C/IIC/RWDT on R8A774E1" from Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>:

Hi All,

This patch series enables support for following on RZ/G2H SoC,
* CPU OPP
* THS
* CMT/TMU
* I2C/IIC
* MSIOF
* RWDT
* SDHI
* SCIF/HSCIF
* CAN/CANFD

Cheers,
Prabhakar

Lad Prabhakar (14):
  dt-bindings: thermal: rcar-gen3-thermal: Add r8a774e1 support
  dt-bindings: timer: renesas,cmt: Document r8a774e1 CMT support
  arm64: dts: renesas: r8a774e1: Add SCIF and HSCIF nodes
  arm64: dts: renesas: r8a774e1: Add SDHI nodes
  dt-bindings: i2c: renesas,i2c: Document r8a774e1 support
  dt-bindings: i2c: renesas,iic: Document r8a774e1 support
  arm64: dts: renesas: r8a774e1: Add I2C and IIC-DVFS support
  dt-bindings: spi: renesas,sh-msiof: Add r8a774e1 support
  arm64: dts: renesas: r8a774e1: Add MSIOF nodes
  dt-bindings: watchdog: renesas,wdt: Document r8a774e1 support
  arm64: dts: renesas: r8a774e1: Add RWDT node
  dt-bindings: can: rcar_can: Document r8a774e1 support
  dt-bindings: can: rcar_canfd: Document r8a774e1 support
  arm64: dts: renesas: r8a774e1: Add CAN[FD] support

Marian-Cristian Rotariu (6):
  arm64: dts: renesas: r8a774e1: Add operating points
  thermal: rcar_gen3_thermal: Add r8a774e1 support
  arm64: dts: renesas: r8a774e1: Add RZ/G2H thermal support
  arm64: dts: renesas: r8a774e1: Add CMT device nodes
  dt-bindings: timer: renesas,tmu: Document r8a774e1 bindings
  arm64: dts: renesas: r8a774e1: Add TMU device nodes

 .../devicetree/bindings/i2c/renesas,i2c.txt   |   1 +
 .../devicetree/bindings/i2c/renesas,iic.txt   |   1 +
 .../devicetree/bindings/net/can/rcar_can.txt  |   1 +
 .../bindings/net/can/rcar_canfd.txt           |   1 +
 .../bindings/spi/renesas,sh-msiof.yaml        |   1 +
 .../bindings/thermal/rcar-gen3-thermal.yaml   |   1 +
 .../bindings/timer/renesas,cmt.yaml           |   2 +
 .../devicetree/bindings/timer/renesas,tmu.txt |   1 +
 .../bindings/watchdog/renesas,wdt.yaml        |   1 +
 arch/arm64/boot/dts/renesas/r8a774e1.dtsi     | 713 +++++++++++++++++-
 drivers/thermal/rcar_gen3_thermal.c           |   4 +
 11 files changed, 715 insertions(+), 12 deletions(-)

--
2.17.1

Since ACPI_PTR() is used to NULLify the value when !CONFIG_ACPI,
struct 'spi_acpi_match' becomes defined but unused.

Fixes the following W=1 kernel build warning(s):

 drivers/spi/spi-amd.c:297:36: warning: ‘spi_acpi_match’ defined but not used [-Wunused-const-variable=]
 297 | static const struct acpi_device_id spi_acpi_match[] = {
 | ^~~~~~~~~~~~~~
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Cc: Sanjay R Mehta <sanju.mehta@amd.com>
Link: https://lore.kernel.org/r/20200717135424.2442271-15-lee.jones@linaro.orgSigned-off-by: Mark Brown <broonie@kernel.org>

Since ACPI_PTR() is used to NULLify the value when !CONFIG_ACPI,
struct 'pxa2xx_spi_acpi_match' becomes defined but unused.

Fixes the following W=1 kernel build warning(s):

 drivers/spi/spi-pxa2xx.c:1435:36: warning: ‘pxa2xx_spi_acpi_match’ defined but not used [-Wunused-const-variable=]
 1435 | static const struct acpi_device_id pxa2xx_spi_acpi_match[] = {
 | ^~~~~~~~~~~~~~~~~~~~~
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Cc: Daniel Mack <daniel@zonque.org>
Cc: Haojian Zhuang <haojian.zhuang@gmail.com>
Cc: Robert Jarzmik <robert.jarzmik@free.fr>
Link: https://lore.kernel.org/r/20200717135424.2442271-14-lee.jones@linaro.orgSigned-off-by: Mark Brown <broonie@kernel.org>

The only way this driver can be probed by MFD via its parent device.

No other reference to 'microchip,at91sam9g45-usart-spi' exists in the kernel.

Fixes the following W=1 kernel build warning(s):

 drivers/spi/spi-at91-usart.c:684:34: warning: ‘at91_usart_spi_dt_ids’ defined but not used [-Wunused-const-variable=]
 684 | static const struct of_device_id at91_usart_spi_dt_ids[] = {
 | ^~~~~~~~~~~~~~~~~~~~~
Suggested-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Cc: Radu Pirea <radu_nicolae.pirea@upb.ro>
Cc: Nicolas Ferre <nicolas.ferre@microchip.com>
Cc: Ludovic Desroches <ludovic.desroches@microchip.com>
Link: https://lore.kernel.org/r/20200717135424.2442271-13-lee.jones@linaro.orgSigned-off-by: Mark Brown <broonie@kernel.org>

Fixes the following W=1 kernel build warning(s):

 drivers/spi/spi-topcliff-pch.c:184: warning: Function parameter or member 'io_base_addr' not described in 'pch_spi_data'
 drivers/spi/spi-topcliff-pch.c:184: warning: Function parameter or member 'pkt_tx_buff' not described in 'pch_spi_data'
 drivers/spi/spi-topcliff-pch.c:184: warning: Function parameter or member 'pkt_rx_buff' not described in 'pch_spi_data'
 drivers/spi/spi-topcliff-pch.c:184: warning: Function parameter or member 'dma' not described in 'pch_spi_data'
 drivers/spi/spi-topcliff-pch.c:184: warning: Function parameter or member 'use_dma' not described in 'pch_spi_data'
 drivers/spi/spi-topcliff-pch.c:184: warning: Function parameter or member 'save_total_len' not described in 'pch_spi_data'
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20200717135424.2442271-12-lee.jones@linaro.orgSigned-off-by: Mark Brown <broonie@kernel.org>

Fixes the following W=1 kernel build warning(s):

 drivers/spi/spi-zynqmp-gqspi.c:205: warning: Function parameter or member 'slavecs' not described in 'zynqmp_gqspi_selectslave'
 drivers/spi/spi-zynqmp-gqspi.c:205: warning: Function parameter or member 'slavebus' not described in 'zynqmp_gqspi_selectslave'
 drivers/spi/spi-zynqmp-gqspi.c:205: warning: Excess function parameter 'flashcs' description in 'zynqmp_gqspi_selectslave'
 drivers/spi/spi-zynqmp-gqspi.c:205: warning: Excess function parameter 'flashbus' description in 'zynqmp_gqspi_selectslave'
 drivers/spi/spi-zynqmp-gqspi.c:902: warning: Function parameter or member 'dev' not described in 'zynqmp_qspi_suspend'
 drivers/spi/spi-zynqmp-gqspi.c:902: warning: Excess function parameter '_dev' description in 'zynqmp_qspi_suspend'
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Reviewed-by: Michal Simek <michal.simek@xilinx.com>
Link: https://lore.kernel.org/r/20200717135424.2442271-11-lee.jones@linaro.orgSigned-off-by: Mark Brown <broonie@kernel.org>

Fixes the following W=1 kernel build warning(s):

 drivers/spi/spi-zynq-qspi.c:143: warning: Function parameter or member 'dev' not described in 'zynq_qspi'
 drivers/spi/spi-zynq-qspi.c:334: warning: Function parameter or member 'spi' not described in 'zynq_qspi_config_op'
 drivers/spi/spi-zynq-qspi.c:334: warning: Excess function parameter 'qspi' description in 'zynq_qspi_config_op'
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Reviewed-by: Michal Simek <michal.simek@xilinx.com>
Cc: Sureshkumar Relli <nagasure@xilinx.com>
Link: https://lore.kernel.org/r/20200717135424.2442271-10-lee.jones@linaro.orgSigned-off-by: Mark Brown <broonie@kernel.org>

Also demote non-worthy kerneldoc headers to standard comment blocks.

Fixes the following W=1 kernel build warning(s):

 drivers/spi/spi-pl022.c:304: warning: cannot understand function prototype: 'enum ssp_writing '
 drivers/spi/spi-pl022.c:330: warning: Function parameter or member 'loopback' not described in 'vendor_data'
 drivers/spi/spi-pl022.c:398: warning: Function parameter or member 'rx_lev_trig' not described in 'pl022'
 drivers/spi/spi-pl022.c:398: warning: Function parameter or member 'tx_lev_trig' not described in 'pl022'
 drivers/spi/spi-pl022.c:398: warning: Function parameter or member 'dma_running' not described in 'pl022'
 drivers/spi/spi-pl022.c:670: warning: Function parameter or member 'pl022' not described in 'readwriter'
 drivers/spi/spi-pl022.c:1250: warning: Function parameter or member 'irq' not described in 'pl022_interrupt_handler'
 drivers/spi/spi-pl022.c:1250: warning: Function parameter or member 'dev_id' not described in 'pl022_interrupt_handler'
 drivers/spi/spi-pl022.c:1343: warning: Function parameter or member 'pl022' not described in 'set_up_next_transfer'
 drivers/spi/spi-pl022.c:1343: warning: Function parameter or member 'transfer' not described in 'set_up_next_transfer'
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Cc: Sachin Verma <sachin.verma@st.com>
Link: https://lore.kernel.org/r/20200717135424.2442271-9-lee.jones@linaro.orgSigned-off-by: Mark Brown <broonie@kernel.org>

Fixes the following W=1 kernel build warning(s):

 drivers/spi/spi-s3c64xx.c:150: warning: Function parameter or member 'quirks' not described in 's3c64xx_spi_port_config'
 drivers/spi/spi-s3c64xx.c:150: warning: Function parameter or member 'clk_ioclk' not described in 's3c64xx_spi_port_config'
 drivers/spi/spi-s3c64xx.c:189: warning: Function parameter or member 'pdev' not described in 's3c64xx_spi_driver_data'
 drivers/spi/spi-s3c64xx.c:189: warning: Function parameter or member 'rx_dma' not described in 's3c64xx_spi_driver_data'
 drivers/spi/spi-s3c64xx.c:189: warning: Function parameter or member 'tx_dma' not described in 's3c64xx_spi_driver_data'
 drivers/spi/spi-s3c64xx.c:189: warning: Function parameter or member 'port_conf' not described in 's3c64xx_spi_driver_data'
 drivers/spi/spi-s3c64xx.c:189: warning: Function parameter or member 'port_id' not described in 's3c64xx_spi_driver_data'
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Cc: Kukjin Kim <kgene@kernel.org>
Cc: Krzysztof Kozlowski <krzk@kernel.org>
Cc: Andi Shyti <andi@etezian.org>
Cc: Jaswinder Singh <jassi.brar@samsung.com>
Cc: linux-samsung-soc@vger.kernel.org
Link: https://lore.kernel.org/r/20200717135424.2442271-8-lee.jones@linaro.orgSigned-off-by: Mark Brown <broonie@kernel.org>

Looks like it hasn't ever been checked.

Fixes the following W=1 kernel build warning(s):

 drivers/spi/spi-meson-spicc.c: In function ‘meson_spicc_reset_fifo’:
 drivers/spi/spi-meson-spicc.c:365:6: warning: variable ‘data’ set but not used [-Wunused-but-set-variable]
 365 | u32 data;
 | ^~~~
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Cc: Kevin Hilman <khilman@baylibre.com>
Cc: Neil Armstrong <narmstrong@baylibre.com>
Cc: linux-amlogic@lists.infradead.org
Link: https://lore.kernel.org/r/20200717135424.2442271-7-lee.jones@linaro.orgSigned-off-by: Mark Brown <broonie@kernel.org>

Fixes the following W=1 kernel build warning(s):

 drivers/spi/spi-meson-spifc.c:80: warning: Function parameter or member 'dev' not described in 'meson_spifc'
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Cc: Kevin Hilman <khilman@baylibre.com>
Cc: Beniamino Galvani <b.galvani@gmail.com>
Cc: linux-amlogic@lists.infradead.org
Link: https://lore.kernel.org/r/20200717135424.2442271-6-lee.jones@linaro.orgSigned-off-by: Mark Brown <broonie@kernel.org>

ep93xx_spi_read_write() changed is parameters, but the function
documentation was left unchanged.  Let's realign.

Fixes the following W=1 kernel build warning(s):

 drivers/spi/spi-ep93xx.c:227: warning: Function parameter or member 'master' not described in 'ep93xx_spi_read_write'
 drivers/spi/spi-ep93xx.c:227: warning: Excess function parameter 'espi' description in 'ep93xx_spi_read_write'
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Cc: Mika Westerberg <mika.westerberg@iki.fi>
Link: https://lore.kernel.org/r/20200717135424.2442271-5-lee.jones@linaro.orgSigned-off-by: Mark Brown <broonie@kernel.org>