This patch explicitly initializes McBSP Transmit Configuration
Control Register (XCCR) and Receive Configuration Control
Register (RCCR) to their reset values. Reset values are 26 ns
of DX delay and Transmit DMA disabled for XCCR register;
receive full cycle mode enabled and Receive DMA disabled for
RCCR register.

This patch requires a counterpart in OMAP McBSP driver before
to apply it. The required changes in McBSP were sent and approved
in linux-omap mailing list and patch is going upstream
(commit 3127f8f8 from linux-omap-2.6
tree).
Signed-off-by: Misael Lopez Cruz <x0052729@ti.com>
[ jarkko.nikula@nokia.com: Commit id for counterpart patch corrected ]
Signed-off-by: Jarkko Nikula <jarkko.nikula@nokia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

The WM8753 driver multiplexes the DAI structures it exposes to the
outside world, leaving them uninitialised until the codec probes.  Since
the DAI name is used during the registration and setup process provide a
dummy name.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc:
  powerpc/mm: Fix handling of _PAGE_COHERENT in BAT setup code
  powerpc/pseries: Correct VIO bus accounting problem in CMO env.
  powerpc: More printing warning fixes for the l64 to ll64 conversion
  powerpc: Remove arch/ppc cruft from Kconfig
  powerpc: Printing fix for l64 to ll64 conversion: phyp_dump.c
  powerpc/embedded6xx: Update defconfigs
  powerpc/8xx: Update defconfigs
  powerpc/86xx: Update defconfigs
  powerpc/83xx: Update defconfigs
  powerpc/85xx: Update defconfigs
  powerpc/mpc8313erdb: fix kernel panic because mdio device is not probed
  powerpc/4xx: Update multi-board PowerPC 4xx defconfigs
  powerpc/44x: Update PowerPC 44x defconfigs
  powerpc/40x: Update PowerPC 40x defconfigs
  powerpc/85xx: Fix typo in mpc8572ds dts
  powerpc/44x: Warp patches for the new NDFC driver
  powerpc/4xx: DTS: Add Add'l SDRAM0 Compatible and Interrupt Info

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/gerg/m68knommu:
  m68knommu: fix 5329 ColdFire periphal addressing
  uclinux: add process name to allocation error message
  m68knommu: correct the mii calculations for 532x ColdFire FEC
  m68knommu: add ColdFire M532x to the FEC configuration options
  m68knommu: fix syscall restarting
  m68knommu: remove the obsolete and long unused comempci chip support
  m68knommu: remove the no longer used PCI support option
  m68knommu: remove obsolete and unused eLIA board
  m68knommu: set NO_DMA
  m68knommu: fix cache flushing for the 527x ColdFire processors
  m68knommu: fix ColdFire 5272 serial baud rates in mcf.c
  m68knommu: use one exist from execption

Commit d7b1956f ("DMI: Introduce
dmi_first_match to make the interface more flexible") introduced compile
errors like the following when !CONFIG_DMI

    drivers/ata/sata_sil.c: In function 'sil_broken_system_poweroff':
    drivers/ata/sata_sil.c:713: error: implicit declaration of function 'dmi_first_match'
    drivers/ata/sata_sil.c:713: warning: initialization makes pointer from integer without a cast

We just need a dummy version of dmi_first_match() to fix this all up.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Schedule a vblank signal, kill the process, and we'll go walking over freed
memory.  Given that no open-source userland exists using this, nor have I
ever heard of a consumer, just let this code die.
Signed-off-by: Eric Anholt <eric@anholt.net>
Requested-by: Linus Torvalds <torvalds@linux-foundation.org>
Acked-by: Dave Airlie <airlied@linux.ie>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Add another MacBook Pro 4,1 SSID (106b:3800). It seems that latter revisions,
(at least mine), have different IDs to earlier revisions.
Signed-off-by: Luke Yelavich <themuso@ubuntu.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>

_PAGE_COHERENT is now always set in _PAGE_RAM resp. PAGE_KERNEL.
Thus it has to be masked out, if the BAT mapping should be non
cacheable or CPU_FTR_NEED_COHERENT is not set.

This will work on normal SMP setups because we force-set
CPU_FTR_NEED_COHERENT as part of CPU_FTR_COMMON on SMP.
Signed-off-by: Gerhard Pircher <gerhard_pircher@gmx.net>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>

In the VIO bus code the wrappers for dma alloc_coherent and free_coherent
calls are rounding to IOMMU_PAGE_SIZE.  Taking a look at the underlying
calls, the actual mapping is promoted to PAGE_SIZE.  Changing the
rounding in these two functions fixes under-reporting the entitlement
used by the system.  Without this change, the system could run out of
entitlement before it believes it has and incur mapping failures at the
firmware level.

Also in the VIO bus code, the wrapper for dma map_sg is not exiting in
an error path where it should.  Rather than fall through to code for the
success case, this patch adds the return that is needed in the error path.
Signed-off-by: Robert Jennings <rcj@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>

These are all powerpc specific drivers.

res.start in fsl_elbc_nand.c needs to be cast since it may be either 32
or 64 bit.  Thanks to Scott Wood for noticing.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Acked-by: Arnd Bergmann <arnd@arndb.de> call_edac bits in particular
Acked-by: Olof Johansson <olof@lixom.net> pasemi_nand peices
Acked-by: Scott Wood <scottwood@freescale.com> fsl_elbc fixes
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>

Remove some leftover cruft from the arch/ppc days
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Acked-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>

Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>

Manual merge of:
	arch/powerpc/configs/44x/warp_defconfig

Given just how hard it is to find the code that uses MAY_APPEND
it's probably not a big surprise that this went unnoticed for so
long. The Smack rules loading code is incorrectly setting the
MAY_READ bit when MAY_APPEND is requested.
Signed-off-by: Casey Schaufler <casey@schaufler-ca.com>
Reviewed-by: James Morris <jmorris@namei.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb-2.6: (36 commits)
  USB: Driver for Freescale QUICC Engine USB Host Controller
  USB: option: add QUANTA HSDPA Data Card device ids
  USB: storage: Add another unusual_dev for off-by-one bug
  USB: unusual_dev: usb-storage needs to ignore a device
  USB: GADGET: fix !x & y
  USB: new id for ti_usb_3410_5052 driver
  USB: cdc-acm: Add another conexant modem to the quirks
  USB: 'option' driver - onda device MT503HS has wrong id
  USB: Remove ZTE modem from unusual_devices
  USB: storage: support of Dane-Elec MediaTouch USB device
  USB: usbmon: Implement compat_ioctl
  USB: add kernel-doc for wusb_dev in struct usb_device
  USB: ftdi_sio driver support of bar code scanner from Diebold
  USB: ftdi_sio: added Alti-2 VID and Neptune 3 PID
  USB: cp2101 device
  USB: usblp.c: add USBLP_QUIRK_BIDIR to Brother HL-1440
  USB: remove vernier labpro from ldusb
  USB: CDC-ACM quirk for MTK GPS
  USB: cdc-acm: support some gps data loggers
  USB: composite: Fix bug: low byte of w_index is the usb interface number not the whole 2 bytes of w_index
  ...

This patch adds support for the FHCI USB controller, as found
in the Freescale MPC836x and MPC832x processors. It can support
Full or Low speed modes.

Quite a lot the hardware is doing by itself (SOF generation, CRC
generation and checking), though scheduling and retransmission is on
software's shoulders.

This controller does not integrate the root hub, so this driver also
fakes one-port hub. External hub is required to support more than
one device.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

This patch adds the support  for the QUANTA Q101 series HSDPA Data Card.
With the vendor and product IDs are set properly,
the data card can be detected and works fine.
Signed-off-by: Alex Cheng <alex.cheng@quantatw.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Argosy has released another device with the off-by-one sector. This is a
harddrive with an internal cardreader which is affected.

Based on a patch written by Martijn Hijdra <martijn.hijdra@gmail.com>
Signed-off-by: Phil Dibowitz <phil@ipom.com>
Cc: Martijn Hijdra <martijn.hijdra@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

This patch adds an unusual_devs entry for a Sony Ericsson modem. Like many
other modems, we have to ignore the storage device in order to access the
modem.


At this time usb_modeswitch does not work with this device.


Reported-by: The Solutor <thesolutor@gmail.com>.
Signed-off-by: Phil Dibowitz <phil@ipom.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

! has a higher precedence than &
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

This adds a new device id
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Another Conexant, another device with the same quirk
Signed-off-by: Alan Cox <alan@redhat.com>
Acked-by: Oliver Neukum <oliver@neukum.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

While trying to make GSM modem Onda MT503HS working, I found a mismatch
between device id in the driver code (0x0200) and id in the lsusb
output (0x2000).

This patch fixed it for me, but I don't know if the original device id was
also correct and the new ID should be added instead of replacing the
old one.
Signed-off-by: Marcel Sebek <sebek64@post.cz>
Acked-by: Domenico Riccio <domenico.riccio@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

The ZTE modem entry causes usb-storage to ignore the device, but for some
versions of the device, usb-storage mode is required to get to modem ode. For
both kinds the tool: http://www.draisberghof.de/usb_modeswitch/ should work.

Note that the various versions of the device have the same ProductId,
VendorId, and bcdDevice number, so we cannot have the entry for some and not
others.
Signed-off-by: Phil Dibowitz <phil@ipom.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

This adds another unusual_devs.h entry for a device that can't handle more
than 64k reads/writes in a single command.
Signed-off-by: Jean-Baptiste Onofre <jb@nanthrax.net>
Signed-off-by: Phil Dibowitz <phil@ipom.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Running a 32-bit usbmon(8) on 2.6.28-rc9 produces the following:
ioctl32(usbmon:28563): Unknown cmd fd(3) cmd(400c9206){t:ffffff92;sz:12} arg(ffd3f458) on /dev/usbmon0

It happens because the compatibility mode was implemented for 2.6.18
and not updated for the fsops.compat_ioctl API.

This patch relocates the pieces from under #ifdef CONFIG_COMPAT into
compat_ioctl with no other changes except one new whitespace.
Signed-off-by: Pete Zaitcev <zaitcev@redhat.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Reported by Randy Dunlap from a warning on the v2.6.29 merge window.
Signed-off-by: Inaky Perez-Gonzalez <inaky@linux.intel.com>
Cc: David Vrabel <david.vrabel@csr.com>
Cc: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Added the product id of bcs(bar code scanner) from Diebold Procomp Brazil.
Signed-off-by: Mhayk Whandson <eu@mhayk.com.br>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

This patch adds the vendor and product ID for the Alti-2 Neptune 3
(http://www.alti-2.com) which uses the FTDI chip.
Signed-off-by: Robie Basak <rb-oss-1@justgohome.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

My girl use modem GSM (EDGE) Commanader 2 on iPlus Polsih provider,

PLEASE add this vendor=0x10C4 and product=0x822B to USB serial driver cp2101.c

From: Tomasz K <eros81@o2.pl>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

My Brother HL-1440 would print one document before CUPS would stop
printing with the error "Printer not connected; will retry in 30
seconds...". I traced this down to the CUPS usb backend getting an EIO
out of usblp on the IOCNR_GET_DEVICE_ID IOCTL. Adding the
USBLP_QUIRK_BIDIR fixes the problem but is it the right solution?

output from strace /usr/lib/cups/backend/usb after printing a document
(Note: SNDCTL_DSP_SYNC == IOCNR_GET_DEVICE_ID):

before patch

open("/dev/usb/lp0", O_RDWR|O_EXCL)     = 3
ioctl(3, SNDCTL_DSP_SYNC, 0x7fff2478cef0) = -1 EIO (Input/output error)

after patch

open("/dev/usb/lp0", O_RDWR|O_EXCL)     = 3
ioctl(3, SNDCTL_DSP_SYNC, 0x7fffb8d474c0) = 0

Possibly related bug: https://bugs.launchpad.net/ubuntu/+source/cupsys/+bug/35638Signed-off-by: Brandon Philips <bphilips@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Labpro device is in both ldusb and vstusb device tables.
Should only be a vstusb device.
Signed-off-by: stephen ware <stephen.ware@eqware.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

This patch adds a device quirk for a MediaTek Inc GPS chipset. The
device implements USB CDC ACM, but is missing the union descriptor, so
the ACM class driver fails to probe the device.

I've tested this patch with an iBlue A+ GPS which uses this chipset
and using kernel 2.6.28-rc9.
Signed-off-by: Andrew Lunn, <andrew@lunn.ch>
Acked-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Below is a patch which allows a number of GPS loggers to work
under linux. It is known to support the i-Blue 747 (all models),
i-Blue 757, Qstarz BT-Q1000, i.Trek Z1, Konet BGL-32, and the Holux
M-241.

From: James A. Treacy <treacy@debian.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

USB: composite: Fix bug: low byte of w_index is the usb interface number not the whole 2 bytes of w_index

In some usb gadget driver, for example usb audio class device, the high
byte of w_index is the entity id and low byte is the interface number.
If we use the 2 bytes of w_index as the array number, we will get a
wrong pointer or NULL pointer.

This patch fixes this issue.
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Signed-off-by: Bryan Wu <cooloney@kernel.org>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>