- 09 Jun, 2020 1 commit
-
-
Geert Uytterhoeven authored
Currently, the RSPI driver always tries to use the maximum configured bit rate for communicating with a slave device, even if the transfer(s) in the current message specify a lower rate. Use the mininum rate specified in the message instead. Rename rspi_data.max_speed_hz accordingly. Signed-off-by:
Geert Uytterhoeven <geert+renesas@glider.be> Link: https://lore.kernel.org/r/20200608095940.30516-3-geert+renesas@glider.beSigned-off-by:
Mark Brown <broonie@kernel.org>
-
- 08 Jun, 2020 1 commit
-
-
Geert Uytterhoeven authored
Consistently use %u to format unsigned numbers. For "bits" this doesn't matter that much, as it is "uint8_t". However, "speed" is "uint32_t", so in case people use "-s -1" to force the maximum, they would see: max speed: -1 Hz (4294967 KHz) While at it, use "k" (kilo) instead of "K" (kelvin) in "kHz". Signed-off-by:
-
- 02 Jun, 2020 1 commit
-
-
Lingling Xu authored
The watchdog counter consists of WDG_LOAD_LOW and WDG_LOAD_HIGH, which would be loaded to watchdog counter once writing WDG_LOAD_LOW. Fixes: ac177501 ("spi: sprd: Add the support of restarting the system") Signed-off-by:
Lingling Xu <ling_ling.xu@unisoc.com> Signed-off-by:
Chunyan Zhang <chunyan.zhang@unisoc.com> Link: https://lore.kernel.org/r/20200602082415.5848-1-zhang.lyra@gmail.comSigned-off-by:
-
- 29 May, 2020 25 commits
-
-
Angelo Dureghello authored
ColdFire is a big-endian cpu with a big-endian dspi hw module, so, it uses native access, but memcpy breaks the endianness. So, if i understand properly, by native copy we would mean be(cpu)->be(dspi) or le(cpu)->le(dspi) accesses, so my fix shouldn't break anything, but i couldn't test it on LS family, so every test is really appreciated. Fixes: 53fadb4d ("spi: spi-fsl-dspi: Simplify bytes_per_word gymnastics") Signed-off-by:
Angelo Dureghello <angelo.dureghello@timesys.com> Tested-by:
Vladimir Oltean <vladimir.oltean@nxp.com> Reviewed-by:
-
Serge Semin authored
Modern device tree bindings are supposed to be created as YAML-files in accordance with dt-schema. This commit replaces two DW SPI legacy bare text bindings with YAML file. As before the bindings file states that the corresponding dts node is supposed to be compatible either with generic DW APB SSI controller or with Microsemi/Amazon/Renesas/Intel vendors-specific controllers, to have registers, interrupts and clocks properties. Though in case of Microsemi version of the controller there must be two registers resources specified. Properties like clock-names, reg-io-width, cs-gpio, num-cs, DMA and slave device sub-nodes are optional. Signed-off-by:
Serge Semin <Sergey.Semin@baikalelectronics.ru> Reviewed-by:
Rob Herring <robh@kernel.org> Cc: Georgy Vlasov <Georgy.Vlasov@baikalelectronics.ru> Cc: Ramil Zaripov <Ramil.Zaripov@baikalelectronics.ru> Cc: Alexey Malahov <Alexey.Malahov@baikalelectronics.ru> Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de> Cc: Feng Tang <feng.tang@intel.com> Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Cc: Arnd Bergmann <arnd@arndb.de> Cc: linux-mips@vger.kernel.org Link: https://lore.kernel.org/r/20200529182544.9807-1-Sergey.Semin@baikalelectronics.ruSigned-off-by:
-
Andy Shevchenko authored
It's better to understand what bits are set for DMA and for IRQ handling in mid_spi_dma_setup() if they are grouped accordingly. Thus, refactor mid_spi_dma_setup() to separate DMA and IRQ configuration. Signed-off-by:
Andy Shevchenko <andriy.shevchenko@linux.intel.com> Link: https://lore.kernel.org/r/20200529183150.44149-2-andriy.shevchenko@linux.intel.comSigned-off-by:
-
Andy Shevchenko authored
The 2afccbd2 ("spi: dw: Discard static DW DMA slave structures") did a clean up of global variables, which is fine, but messed up with the carefully provided information in the custom DMA slave structures. There reader can find an assignment of the DMA request lines in use. Partially revert the above mentioned commit to restore readability and maintainability of the code. Signed-off-by:
-
Mark Brown authored
This reverts commit ecfbd3cf since Lukas Wunner noticed that we start operating on the hardware before we check to see if this is a spurious interrupt. Reported-by:
Lukas Wunner <lukas@wunner.de> Signed-off-by:
-
Mark Brown authored
Merge series "spi: dw: Add generic DW DMA controller support" from Serge Semin <Sergey.Semin@baikalelectronics.ru>: Baikal-T1 SoC provides a DW DMA controller to perform low-speed peripherals Mem-to-Dev and Dev-to-Mem transaction. This is also applicable to the DW APB SSI devices embedded into the SoC. Currently the DMA-based transfers are supported by the DW APB SPI driver only as a middle layer code for Intel MID/Elkhart PCI devices. Seeing the same code can be used for normal platform DMAC device we introduced a set of patches to fix it within this series. First of all we need to add the Tx and Rx DMA channels support into the DW APB SSI binding. Then there are several fixes and cleanups provided as a initial preparation for the Generic DMA support integration: add Tx/Rx finish wait methods, clear DMAC register when done or stopped, Fix native CS being unset, enable interrupts in accordance with DMA xfer mode, discard static DW DMA slave structures, discard unused void priv pointer and dma_width member of the dw_spi structure, provide the DMA Tx/Rx burst length parametrisation and make sure it's optionally set in accordance with the DMA max-burst capability. In order to have the DW APB SSI MMIO driver working with DMA we need to initialize the paddr field with the physical base address of the DW APB SSI registers space. Then we unpin the Intel MID specific code from the generic DMA one and placed it into the spi-dw-pci.c driver, which is a better place for it anyway. After that the naming cleanups are performed since the code is going to be used for a generic DMAC device. Finally the Generic DMA initialization can be added to the generic version of the DW APB SSI IP. Last but not least we traditionally convert the legacy plain text-based dt-binding file with yaml-based one and as a cherry on a cake replace the manually written DebugFS registers read method with a ready-to-use for the same purpose regset32 DebugFS interface usage. This patchset is rebased and tested on the spi/for-next (5.7-rc5): base-commit: fe9fce6b2cf3 ("Merge remote-tracking branch 'spi/for-5.8' into spi-next") Link: https://lore.kernel.org/linux-spi/20200508132943.9826-1-Sergey.Semin@baikalelectronics.ru/ Changelog v2: - Rebase on top of the spi repository for-next branch. - Move bindings conversion patch to the tail of the series. - Move fixes to the head of the series. - Apply as many changes as possible to be applied the Generic DMA functionality support is added and the spi-dw-mid is moved to the spi-dw-dma driver. - Discard patch "spi: dw: Fix dma_slave_config used partly uninitialized" since the problem has already been fixed. - Add new patch "spi: dw: Discard unused void priv pointer". - Add new patch "spi: dw: Discard dma_width member of the dw_spi structure". n_bytes member of the DW SPI data can be used instead. - Build the DMA functionality into the DW APB SSI core if required instead of creating a separate kernel module. - Use conditional statement instead of the ternary operator in the ref clock getter. Link: https://lore.kernel.org/linux-spi/20200515104758.6934-1-Sergey.Semin@baikalelectronics.ru/ Changelog v3: - Use spi_delay_exec() method to wait for the DMA operation completion. - Explicitly initialize the dw_dma_slave members on stack. - Discard the dws->fifo_len utilization in the Tx FIFO DMA threshold setting from the patch where we just add the default burst length constants. - Use min() method to calculate the optimal burst values. - Add new patch which moves the spi-dw.c source file to spi-dw-core.c in order to preserve the DW APB SSI core driver name. - Add commas in the debugfs_reg32 structure initializer and after the last entry of the dw_spi_dbgfs_regs array. Link: https://lore.kernel.org/linux-spi/20200521012206.14472-1-Sergey.Semin@baikalelectronics.ru Changelog v4: - Get back ndelay() method to wait for an SPI transfer completion. spi_delay_exec() isn't suitable for the atomic context. Link: https://lore.kernel.org/linux-spi/20200522000806.7381-1-Sergey.Semin@baikalelectronics.ru Changelog v5: - Refactor the Tx/Rx DMA-based SPI transfers wait methods. - Add a new patch "spi: dw: Set xfer effective_speed_hz". - Add a new patch "spi: dw: Return any value retrieved from the dma_transfer callback" as a preparation patch before implementing the local DMA, Tx SPI and Rx SPI transfers wait methods. - Add a new patch "spi: dw: Locally wait for the DMA transactions completion", which provides a local DMA transaction complete method - Create a dedicated patch which adds the Rx-done wait method: "spi: dw: Add SPI Rx-done wait method to DMA-based transfer". - Add more detailed description of the problems the Tx/Rx-wait methods-related patches fix. - Wait for the SPI Tx and Rx transfers being finished in the mid_spi_dma_transfer() method executed in the task context. - Use spi_delay_exec() to wait for the SPI Tx/Rx completion, since now the driver calls the wait methods in the kernel thread context. - Use SPI_DELAY_UNIT_SCK spi_delay unit for Tx-wait delay, since SPI xfer's are now have the effective_speed_hz initialized. - Rx-wait for a delay correlated with the APB/SSI synchronous clock rate instead of using the SPI bus clock rate. Link: https://lore.kernel.org/linux-spi/20200529035915.20790-1-Sergey.Semin@baikalelectronics.ru Changelog v6: - Provide a more detailed description of the patch: 2901db35bea1 ("spi: dw: Locally wait for the DMA transfers completion") - Calculate the Rx delay with better accuracy by moving 4-multiplication to the head of the formulae: ns = 4U * NSEC_PER_SEC / dws->max_freq * nents. Co-developed-by:Georgy Vlasov <Georgy.Vlasov@baikalelectronics.ru> Signed-off-by:
Ramil Zaripov <Ramil.Zaripov@baikalelectronics.ru> Signed-off-by:
-
Dinh Nguyen authored
Add optional reset property. Signed-off-by:
Dinh Nguyen <dinguyen@kernel.org> Link: https://lore.kernel.org/r/20200529155806.16758-2-dinguyen@kernel.orgSigned-off-by:
-
Dinh Nguyen authored
Add mechanism to get the reset control and deassert it in order to bring the IP out of reset. Signed-off-by:
Liang Jin J <liang.j.jin@ericsson.com> Signed-off-by:
-
Martin Sperl authored
bcm2711, Rasberry Pi 4's SoC, shares one interrupt for multiple instances of the bcm2835 SPI controller. So this enables shared interrupt support for them. The early bail out in the interrupt routine avoids messing with buffers of transfers being done by other means. Otherwise, the driver can handle receiving interrupts asserted by other controllers during an IRQ based transfer. Signed-off-by:
Martin Sperl <kernel@martin.sperl.org> Signed-off-by:
Nicolas Saenz Julienne <nsaenzjulienne@suse.de> Tested-by:
Florian Fainelli <f.fainelli@gmail.com> Acked-by:
-
Florian Fainelli authored
Make sure we clear the FIFOs, stop the block, disable the clock and release the DMA channel. Signed-off-by:
-
Serge Semin authored
DebugFS kernel interface provides a dedicated method to create the registers dump file. Use it instead of creating a generic DebugFS file with manually written read callback function. Signed-off-by:
-
Serge Semin authored
Since the common code in the spi-dw-dma.c driver is ready to be used by the MMIO driver and now provides a method to generically (on any DT or ACPI-based platforms) retrieve the Tx/Rx DMA channel handlers, we can use it and a set of the common DW SPI DMA callbacks to enable DMA at least for generic "snps,dw-apb-ssi" and "snps,dwc-ssi-1.01a" devices. Co-developed-by:
-
Serge Semin authored
Since from now the former Intel MID platform layer is used as a generic DW SPI DMA module, let's alter the internal methods naming to be DMA-related instead of having the "mid_" prefix. Co-developed-by:
-
Serge Semin authored
Seeing all of the DW SPI driver components like DW SPI DMA/PCI/MMIO depend on the DW SPI core code it's better to use the if-endif conditional kernel config statement to signify that common dependency. Co-developed-by:
-
Serge Semin authored
Since there is a generic method available to initialize the DW SPI DMA interface on any DT and ACPI-based platforms, which in general can be designed with not only DW DMAC but with any DMA engine on board, we can freely remove the CONFIG_DW_DMAC_PCI config from dependency list of CONFIG_SPI_DW_DMA. Especially seeing that we don't use anything DW DMAC specific in the new driver. Co-developed-by:
-
Serge Semin authored
This is a preparation patch before adding the DW DMA support into the DW SPI MMIO driver. We need to unpin the Non-DMA-specific code from the intended to be generic DW APB SSI DMA code. This isn't that hard, since the most part of the spi-dw-mid.c driver in fact implements a generic DMA interface for the DW SPI controller driver. The only Intel MID specifics concern getting the max frequency from the MRST Clock Control Unit and fetching the DMA controller channels from corresponding PCIe DMA controller. Since first one is related with the SPI interface configuration we moved it' implementation into the DW PCIe-SPI driver module. After that former spi-dw-mid.c file can be just renamed to be the DW SPI DMA module optionally compiled in to the DW APB SSI core driver. Co-developed-by:
-
Serge Semin authored
Generic DMA support is going to be part of the DW APB SSI core object. In order to preserve the kernel loadable module name as spi-dw.ko, let's add the "-core" suffix to the object with generic DW APB SSI code and build it into the target spi-dw.ko driver. Suggested-by:
-
Serge Semin authored
Tx-only DMA transfers are working perfectly fine since in this case the code just ignores the Rx FIFO overflow interrupts. But it turns out the SPI Rx-only transfers are broken since nothing pushing any data to the shift registers, so the Rx FIFO is left empty and the SPI core subsystems just returns a timeout error. Since DW DMAC driver doesn't support something like cyclic write operations of a single byte to a device register, the only way to support the Rx-only SPI transfers is to fake it by using a dummy Tx-buffer. This is what we intend to fix in this commit by setting the SPI_CONTROLLER_MUST_TX flag for DMA-capable platform. Signed-off-by:
-
Serge Semin authored
Each channel of DMA controller may have a limited length of burst transaction (number of IO operations performed at ones in a single DMA client request). This parameter can be used to setup the most optimal DMA Tx/Rx data level values. In order to avoid the Tx buffer overrun we can set the DMA Tx level to be of FIFO depth minus the maximum burst transactions length. To prevent the Rx buffer underflow the DMA Rx level should be set to the maximum burst transactions length. This commit setups the DMA channels and the DW SPI DMA Tx/Rx levels in accordance with these rules. Signed-off-by:
-
Serge Semin authored
It isn't good to have numeric literals in the code especially if there are multiple of them and they are related. Let's replace the Tx and Rx burst level literals with the corresponding constants. Co-developed-by:
-
Serge Semin authored
Having any data left in the Rx FIFO after the DMA engine claimed it has finished all DMA transactions is an abnormal situation, since the DW SPI controller driver expects to have all the data being fetched and placed into the SPI Rx buffer at that moment. In case if that has happened we hopefully assume that the DMA engine may still be doing the data fetching, thus we give it sometime to finish. If after a short period of time the data is still left in the Rx FIFO, the driver will give up waiting and return an error indicating that the SPI controller/DMA engine must have hung up or failed at some point of doing their duties. Fixes: 7063c0d9 ("spi/dw_spi: add DMA support") Co-developed-by:
-
Serge Semin authored
Since DMA transfers are performed asynchronously with actual SPI bus transfers, then even if DMA transactions are finished it doesn't mean all data is actually pushed to the SPI bus. Some data might still be in the controller FIFO. This is specifically true for Tx-only transfers. In this case if the next SPI transfer is recharged while a tail of the previous one is still in FIFO, we'll loose that tail data. In order to fix that problem let's add the wait procedure of the Tx SPI transfer completion after the DMA transactions are finished. Fixes: 7063c0d9 ("spi/dw_spi: add DMA support") Co-developed-by:
-
Serge Semin authored
In general each DMA-based SPI transfer can be split up into two stages: DMA data transmission/reception and SPI-bus transmission/reception. DMA asynchronous transactions completion can be tracked by means of the DMA async Tx-descriptor completion callback. But that callback being called indicates that the DMA transfer has been finished, it doesn't mean that SPI data transmission is also done. Moreover in fact it isn't for at least Tx-only SPI transfers. Upon DMA transfer completion some data is left in the Tx FIFO and being pushed out by the SPI controller. So in order to make sure that an SPI transfer is completely pushed to the SPI-bus, the driver has to wait for both DMA transaction and the SPI-bus transmission/reception are finished. Note if there is a way to asynchronously track the former event by means of the DMA async Tx callback, there isn't easy one for the later (IRQ-based solution won't work since SPI controller doesn't notify about Rx FIFO being empty). The DMA transfer completion callback isn't suitable to wait for the SPI controller activity finish either. The callback might (in case of DW DMAC it will) be called in the tasklet context. Waiting for the SPI controller to complete the transfer might take a considerable amount of time since SPI-bus might be pretty slow. In this case delaying the execution in the tasklet atomic context might cause significant system performance drop. So to speak the best option we've got to solve the problem is to consequently wait for both stages being finished in the locally implemented SPI transfer execution procedure even if it costs us of the local wait-function re-implementation. In this case we don't need to use the SPI-core transfer-wait functionality, but we'll make sure that all DMA and SPI-bus transactions are completely finished before the SPI-core transfer_one callback returns. In this commit we provide an implementation of the DMA-transfers completion wait functionality. The DW APB SSI DMA-specific SPI transfer_one function waits for both Tx and Rx DMA transfers being finished, and only then exits with zero returned signalling to the SPI core that the SPI transfer is finished. This implementation is fully equivalent to the currently used DMA-execution-SPI-core-wait algorithm. The SPI-bus transmission/reception wait methods will be added in the follow-up commits. Signed-off-by:
-
Serge Semin authored
DW APB SSI DMA-part of the driver may need to perform the requested SPI-transfer synchronously. In that case the dma_transfer() callback will return 0 as a marker of the SPI transfer being finished so the SPI core doesn't need to wait and may proceed with the SPI message trasnfers pumping procedure. This will be needed to fix the problem when DMA transactions are finished, but there is still data left in the SPI Tx/Rx FIFOs being sent/received. But for now make dma_transfer to return 1 as the normal dw_spi_transfer_one() method. Signed-off-by:
-
Serge Semin authored
Seeing DW APB SSI controller doesn't support setting the exactly requested SPI bus frequency, but only a rounded frequency determined by means of the odd-numbered half-worded reference clock divider, it would be good to tune the SPI core up and initialize the current transfer effective_speed_hz. By doing so the core will be able to execute the xfer-related delays with better accuracy. Signed-off-by:
-
- 28 May, 2020 5 commits
-
-
Mark Brown authored
There is ecspi ERR009165 on i.mx6/7 soc family, which cause FIFO transfer to be send twice in DMA mode. Please get more information from: https://www.nxp.com/docs/en/errata/IMX6DQCE.pdf. The workaround is adding new sdma ram script which works in XCH mode as PIO inside sdma instead of SMC mode, meanwhile, 'TX_THRESHOLD' should be 0. The issue should be exist on all legacy i.mx6/7 soc family before i.mx6ul. NXP fix this design issue from i.mx6ul, so newer chips including i.mx6ul/ 6ull/6sll do not need this workaroud anymore. All other i.mx6/7/8 chips still need this workaroud. This patch set add new 'fsl,imx6ul-ecspi' for ecspi driver and 'ecspi_fixed' in sdma driver to choose if need errata or not. The first two reverted patches should be the same issue, though, it seems 'fixed' by changing to other shp script. Hope Sean or Sascha could have the chance to test this patch set if could fix their issues. Besides, enable sdma support for i.mx8mm/8mq and fix ecspi1 not work on i.mx8mm because the event id is zero. PS: Please get sdma firmware from below linux-firmware and copy it to your local rootfs /lib/firmware/imx/sdma. https://git.kernel.org/pub/scm/linux/kernel/git/firmware/linux-firmware.git/tree/imx/sdma v2: 1.Add commit log for reverted patches. 2.Add comment for 'ecspi_fixed' in sdma driver. 3.Add 'fsl,imx6sll-ecspi' compatible instead of 'fsl,imx6ul-ecspi' rather than remove. v3: 1.Confirm with design team make sure ERR009165 fixed on i.mx6ul/i.mx6ull /i.mx6sll, not fixed on i.mx8m/8mm and other i.mx6/7 legacy chips. Correct dts related dts patch in v2. 2.Clean eratta information in binding doc and new 'tx_glitch_fixed' flag in spi-imx driver to state ERR009165 fixed or not. 3.Enlarge burst size to fifo size for tx since tx_wml set to 0 in the errata workaroud, thus improve performance as possible. v4: 1.Add Ack tag from Mark and Vinod 2.Remove checking 'event_id1' zero as 'event_id0'. v5: 1.Add the last patch for compatible with the current uart driver which using rom script, so both uart ram script and rom script supported in latest firmware, by default uart rom script used. UART driver will be broken without this patch. v6: 1.Resend after rebase the latest next branch. 2.Remove below No.13~No.15 patches of v5 because they were mergered. ARM: dts: imx6ul: add dma support on ecspi ARM: dts: imx6sll: correct sdma compatible arm64: defconfig: Enable SDMA on i.mx8mq/8mm 3.Revert "dmaengine: imx-sdma: fix context cache" since 'context_loaded' removed. v7: 1.Put the last patch 13/13 'Revert "dmaengine: imx-sdma: fix context cache"' to the ahead of 03/13 'Revert "dmaengine: imx-sdma: refine to load context only once" so that no building waring during comes out during bisect. 2.Address Sascha's comments, including eliminating any i.mx6sx in this series, adding new 'is_imx6ul_ecspi()' instead imx in imx51 and taking care SMC bit for PIO. 3.Add back missing 'Reviewed-by' tag on 08/15(v5):09/13(v7) 'spi: imx: add new i.mx6ul compatible name in binding doc' v8: 1.remove 0003-Revert-dmaengine-imx-sdma-fix-context-cache.patch and merge it into 04/13 of v7 2.add 0005-spi-imx-fallback-to-PIO-if-dma-setup-failure.patch for no any ecspi function broken even if sdma firmware not updated. 3.merge 'tx.dst_maxburst' changes in the two continous patches into one patch to avoid confusion. 4.fix typo 'duplicated'. Robin Gong (13): Revert "ARM: dts: imx6q: Use correct SDMA script for SPI5 core" Revert "ARM: dts: imx6: Use correct SDMA script for SPI cores" Revert "dmaengine: imx-sdma: refine to load context only once" dmaengine: imx-sdma: remove duplicated sdma_load_context spi: imx: fallback to PIO if dma setup failure dmaengine: imx-sdma: add mcu_2_ecspi script spi: imx: fix ERR009165 spi: imx: remove ERR009165 workaround on i.mx6ul spi: imx: add new i.mx6ul compatible name in binding doc dmaengine: imx-sdma: remove ERR009165 on i.mx6ul dma: imx-sdma: add i.mx6ul compatible name dmaengine: imx-sdma: fix ecspi1 rx dma not work on i.mx8mm dmaengine: imx-sdma: add uart rom script .../devicetree/bindings/dma/fsl-imx-sdma.txt | 1 + .../devicetree/bindings/spi/fsl-imx-cspi.txt | 1 + arch/arm/boot/dts/imx6q.dtsi | 2 +- arch/arm/boot/dts/imx6qdl.dtsi | 8 +- drivers/dma/imx-sdma.c | 67 ++++++++++------ drivers/spi/spi-imx.c | 92 +++++++++++++++++++--- include/linux/platform_data/dma-imx-sdma.h | 8 +- 7 files changed, 135 insertions(+), 44 deletions(-) -- 2.7.4 _______________________________________________ linux-arm-kernel mailing list linux-arm-kernel@lists.infradead.org http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
-
Dinghao Liu authored
pm_runtime_get_sync() increments the runtime PM usage counter even when it returns an error code. Thus a pairing decrement is needed on the error handling path to keep the counter balanced. Signed-off-by:
Dinghao Liu <dinghao.liu@zju.edu.cn> Link: https://lore.kernel.org/r/20200523124758.28604-1-dinghao.liu@zju.edu.cnSigned-off-by:
-
Dinghao Liu authored
pm_runtime_get_sync() increments the runtime PM usage counter even when it returns an error code. Thus a pairing decrement is needed on the error handling path to keep the counter balanced. Signed-off-by:
-
Dinghao Liu authored
pm_runtime_get_sync() increments the runtime PM usage counter even when it returns an error code. Thus a pairing decrement is needed on the error handling path to keep the counter balanced. Signed-off-by:
-
Robin Gong authored
Fallback to PIO in case dma setup failed. For example, sdma firmware not updated but ERR009165 workaroud added in kernel. Signed-off-by:
Robin Gong <yibin.gong@nxp.com> Acked-by:
Sascha Hauer <s.hauer@pengutronix.de> Link: https://lore.kernel.org/r/1590006865-20900-6-git-send-email-yibin.gong@nxp.comSigned-off-by:
-
- 26 May, 2020 2 commits
-
-
Dinghao Liu authored
pm_runtime_get_sync() increments the runtime PM usage counter even when it returns an error code. Thus a pairing decrement is needed on the error handling path to keep the counter balanced. Signed-off-by:
-
Mark Brown authored
Originally spi_write_then_read() used a fixed statically allocated buffer which limited the maximum message size it could handle. This restriction was removed a while ago so that we could dynamically allocate a buffer if required but the kerneldoc was not updated to reflect this, do so. Reported-by:
Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by:
-
- 25 May, 2020 2 commits
-
-
dillon min authored
spi: flags 'SPI_CONTROLLER_MUST_RX' and 'SPI_CONTROLLER_MUST_TX' can't be coexit with 'SPI_3WIRE' mode since chip spi driver need get the transfer direction by 'tx_buf' and 'rx_buf' of 'struct spi_transfer' in 'SPI_3WIRE' mode. so, we need bypass 'SPI_CONTROLLER_MUST_RX' and 'SPI_CONTROLLER_MUST_TX' feature in 'SPI_3WIRE' mode Signed-off-by:
dillon min <dillon.minfei@gmail.com> Link: https://lore.kernel.org/r/1590378348-8115-9-git-send-email-dillon.minfei@gmail.comSigned-off-by:
-
dillon min authored
in l3gd20 driver startup, there is a setup failed error return from stm32 spi driver " [ 2.687630] st-gyro-spi spi0.0: supply vdd not found, using dummy regulator [ 2.696869] st-gyro-spi spi0.0: supply vddio not found, using dummy regulator [ 2.706707] spi_stm32 40015000.spi: SPI transfer setup failed [ 2.713741] st-gyro-spi spi0.0: SPI transfer failed: -22 [ 2.721096] spi_master spi0: failed to transfer one message from queue [ 2.729268] iio iio:device0: failed to read Who-Am-I register. [ 2.737504] st-gyro-spi: probe of spi0.0 failed with error -22 " after debug into spi-stm32 driver, st-gyro-spi split two steps to read l3gd20 id first: send command to l3gd20 with read id command in tx_buf, rx_buf is null. second: read id with tx_buf is null, rx_buf not null. so, for second step, stm32 driver recongise this process as 'SPI_SIMPLE_RX' from stm32_spi_communication_type(), but there is no related process for this type in stm32f4_spi_set_mode(), then we get error from stm32_spi_transfer_one_setup(). we can use two method to fix this bug. 1, use stm32 spi's "In unidirectional receive-only mode (BIDIMODE=0 and RXONLY=1)". but as our code running in sdram, the read latency is too large to get so many receive overrun error in interrupts handler. 2, use stm32 spi's "In full-duplex (BIDIMODE=0 and RXONLY=0)", as tx_buf is null, so add flag 'SPI_MASTER_MUST_TX' to spi master. Change since V4: 1 remove dummy data sent out by stm32 spi driver 2 add flag 'SPI_MASTER_MUST_TX' to spi master Signed-off-by:
-
- 22 May, 2020 3 commits
-
-
Mark Brown authored
If the delay used is long enough the spi_delay_exec() will use a sleeping function to implement it. Add a might_sleep() here to help avoid callers using this from an atomic context and running into problems at runtime on other systems. Suggested-by:
-
Mark Brown authored
Merge series "spi: dw: Add generic DW DMA controller support" from Serge Semin <Sergey.Semin@baikalelectronics.ru>: Baikal-T1 SoC provides a DW DMA controller to perform low-speed peripherals Mem-to-Dev and Dev-to-Mem transaction. This is also applicable to the DW APB SSI devices embedded into the SoC. Currently the DMA-based transfers are supported by the DW APB SPI driver only as a middle layer code for Intel MID/Elkhart PCI devices. Seeing the same code can be used for normal platform DMAC device we introduced a set of patches to fix it within this series. First of all we need to add the Tx and Rx DMA channels support into the DW APB SSI binding. Then there are several fixes and cleanups provided as a initial preparation for the Generic DMA support integration: add Tx/Rx finish wait methods, clear DMAC register when done or stopped, Fix native CS being unset, enable interrupts in accordance with DMA xfer mode, discard static DW DMA slave structures, discard unused void priv pointer and dma_width member of the dw_spi structure, provide the DMA Tx/Rx burst length parametrisation and make sure it's optionally set in accordance with the DMA max-burst capability. In order to have the DW APB SSI MMIO driver working with DMA we need to initialize the paddr field with the physical base address of the DW APB SSI registers space. Then we unpin the Intel MID specific code from the generic DMA one and placed it into the spi-dw-pci.c driver, which is a better place for it anyway. After that the naming cleanups are performed since the code is going to be used for a generic DMAC device. Finally the Generic DMA initialization can be added to the generic version of the DW APB SSI IP. Last but not least we traditionally convert the legacy plain text-based dt-binding file with yaml-based one and as a cherry on a cake replace the manually written DebugFS registers read method with a ready-to-use for the same purpose regset32 DebugFS interface usage. This patchset is rebased and tested on the spi/for-next (5.7-rc5): base-commit: fe9fce6b2cf3 ("Merge remote-tracking branch 'spi/for-5.8' into spi-next") Link: https://lore.kernel.org/linux-spi/20200508132943.9826-1-Sergey.Semin@baikalelectronics.ru/ Changelog v2: - Rebase on top of the spi repository for-next branch. - Move bindings conversion patch to the tail of the series. - Move fixes to the head of the series. - Apply as many changes as possible to be applied the Generic DMA functionality support is added and the spi-dw-mid is moved to the spi-dw-dma driver. - Discard patch "spi: dw: Fix dma_slave_config used partly uninitialized" since the problem has already been fixed. - Add new patch "spi: dw: Discard unused void priv pointer". - Add new patch "spi: dw: Discard dma_width member of the dw_spi structure". n_bytes member of the DW SPI data can be used instead. - Build the DMA functionality into the DW APB SSI core if required instead of creating a separate kernel module. - Use conditional statement instead of the ternary operator in the ref clock getter. Link: https://lore.kernel.org/linux-spi/20200515104758.6934-1-Sergey.Semin@baikalelectronics.ru/ Changelog v3: - Use spi_delay_exec() method to wait for the DMA operation completion. - Explicitly initialize the dw_dma_slave members on stack. - Discard the dws->fifo_len utilization in the Tx FIFO DMA threshold setting from the patch where we just add the default burst length constants. - Use min() method to calculate the optimal burst values. - Add new patch which moves the spi-dw.c source file to spi-dw-core.c in order to preserve the DW APB SSI core driver name. - Add commas in the debugfs_reg32 structure initializer and after the last entry of the dw_spi_dbgfs_regs array. Link: https://lore.kernel.org/linux-spi/20200521012206.14472-1-Sergey.Semin@baikalelectronics.ru Changelog v4: - Get back ndelay() method to wait for an SPI transfer completion. spi_delay_exec() isn't suitable for the atomic context. Co-developed-by: -
Christopher Hill authored
This patch adds the correcsponding MikroTik vendor and device tree documentation Signed-off-by:
Christopher Hill <ch6574@gmail.com> Link: https://lore.kernel.org/r/20200521183631.37806-3-ch6574@gmail.comSigned-off-by:
-
