This patch adds the configuration needed for the LCD display on the n30.
Signed-off-by: Christer Weinigel <christer@weinigel.se>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>

Add support for the Acer N35 and related devices.
Signed-off-by: Christer Weinigel <christer@weinigel.se>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>

Add support for the LEDs on the Acer N30.
Signed-off-by: Christer Weinigel <christer@weinigel.se>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>

Add support for the GPIO buttons on the Acer N30.
Signed-off-by: Christer Weinigel <christer@weinigel.se>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>

Add support for the USB D+ pull up on the Acer N30.  This is needed
for the USB gadget to work properly.
Signed-off-by: Christer Weinigel <christer@weinigel.se>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>

Clean up some junk from the official kernel.

The compile-command is something that's only useful for me personally
and doesn't belong in the mainstream kernel.
Signed-off-by: Christer Weinigel <christer@weinigel.se>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>

Update the S3C2443 clock support to add the prediv clock
that is sourced via a divider from msysclk. Also fix the
setting of p and h clocks from this prediv clock.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>

Add the armdiv and arm clocks to the S3C2443 clock
framework and ensure they are correctly setup.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>

s3c2443_clkcon_enable_p() was reading from the correct register
S3C2443_PCLKCON, but then writing the value back to the wrong
register S3C2443_HCLKCON.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>

Add DM9000AEP network controller support for AT2440EVB.
Signed-off-by: Ramax Lo <ramaxlo@gmail.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>

Add basic support for AT2440EVB board based on Samsung S3C2440 SoC.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Ramax Lo <ramaxlo@gmail.com>

The S3C2410 serial driver in drivers/serial/s3c2410.c has been
growing bigger with the addition of more variants of this hardware
with the growing Samsung SoCs range. As such, it would be
easier to split this code up into a core and per-cpu drivers to
make driver addition easier, and the core smaller.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>

Add support for PWM in the S3C24XX series of SoC via the
PWM API.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>

For s3c2412, set parent for clk_erefclk and clk_urefclk.
This allow for example to use xtal or extclk for i2s clock.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Matthieu Castet <matthieu.castet@parrot.com>

Add tmp101 support via the new style I2C driver registration
on the VR1000.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>

Add i2c board info initialiser to setup the list of
I2C devices present on an Simtec Anubis.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>

Add i2c board intialisers to specify the I2C devices
attached on the Thorcom VR1000.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>

Add i2c boardinfo for the connected i2c devices on the
Simtec Bast.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>

Add an i2c board information initialisers to the board
to define which devices are present.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>

Move to using the physmap platform device code to attached NOR
flash on Simtec boards so that the old bast-flash driver can be
safely removed.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>

Change the (as yet unused) IDE bus on the Simtec Anubis board
to use pata_platform and thus libata to provide IDE support.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>

Use the pata_platform driver to provide the IDE port
drivers on the Simntec BAST and Thorcom VR1000 machines
as a precursor to removing drivers/ide/arm/bast-ide.c

This will mean that the system will need SCSI and SCSI disc
support as a minimum, and any references to hdX will be
changed to sdX.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>

Add pm_power_off hook to allow the Logitech Jive to shutdown
when asked to halt.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>

Add i2c bus definition for the LIS302DL sensor driver
which is connected on the i2c bus.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>

Add board definitions for the audio device connected
on the Logitech Jive.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>

Add the setup information for the LCD display
connected to the device.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>

Add the definitions for the VGG2432A4 intelligent
LCD display conneected via an GPIO-based SPI bus
on the Logitech Jive.
Signed-of-by: Ben Dooks <ben-linux@fluff.org>

Setup the video controller information for the Jive.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>

Ensure that the S3C2412 sleep configuration registers
are approriately setup so that the device can safely
go to sleep.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>

This is the base machine support for the Logitech Jive
machine.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>

Add support for the PWM timer clock routing via the
standard clk_ API.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>

Add timer defines for the MUX settings for
each of the PWM timers to add to the per-timer
defines already in the file.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>

Add support for gpilib on all S3C24XX platforms.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>

Enable a subset of USB drivers which are useful for
using on these devices.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>

Enable SCSI support, mainly to help with adding
USB storage support later and for the imminent
changes for libata.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>

Add the following to the networking confgiuration:

1) Packet socket support (useful for userland dhcp)
2) Add bluetooth and USB bluetooth drivers as modules
3) Add basic IPv6 support as modules.
4) Add the wireless core as modules.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>

Add some basic config filesystem, ensure errors are verbose
by default.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>

Enable new filesystem options, such as:

- JFFS2 summary nodes
- Ext2/3 externed options
- Standard CDROM filesystems

Also add NTFS as a module.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>

Enable some useful NLS codepages to be built into
the kernel, and build the rest as modules.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>

Update the drivers built, such as the SM501 and
parallel port.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>