Spelling fixes in arch/sparc64/.
Signed-off-by: Simon Arlott <simon@fire.lp0.eu>
Signed-off-by: David S. Miller <davem@davemloft.net>

Spelling fixes in arch/sparc/.
Signed-off-by: Simon Arlott <simon@fire.lp0.eu>
Signed-off-by: David S. Miller <davem@davemloft.net>

Let's use SLUB, since it works now, in order to get it
tested a bit.
Signed-off-by: David S. Miller <davem@davemloft.net>

* 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc: (23 commits)
  [POWERPC] Add arch/powerpc support for the Motorola PrPMC2800
  [POWERPC] Add bootwrapper support for Motorola PrPMC2800 platform
  [POWERPC] Add DTS file for the Motorola PrPMC2800 platform
  [POWERPC] Check cache coherency of kernel vs firmware
  [POWERPC] Add Marvell mv64x60 PCI bridge support
  [POWERPC] Create Marvell mv64x60 I2C platform_data
  [POWERPC] Create Marvell mv64x60 ethernet platform_data
  [POWERPC] Create Marvell mv64x60 MPSC (serial) platform_data
  [POWERPC] Add interrupt support for Marvell mv64x60 chips
  [POWERPC] Add bootwrapper support for Marvell/mv64x60 I2C
  [POWERPC] Add bootwrapper support for Marvell MPSC
  [POWERPC] Add bootwrapper support for Marvell/mv64x60 hostbridge
  [POWERPC] Add Makefile rules to wrap dts file in zImage
  [POWERPC] Spelling fixes: arch/ppc/
  [POWERPC] U-boot passes the initrd as start/end, not start/size.
  [POWERPC] PS3: Update ps3_defconfig
  [POWERPC] PS3: Fix request_irq warning
  [POWERPC] Don't complain if size-cells == 0 in prom_parse()
  [POWERPC] Simplify smp_space_timers
  [POWERPC] Trivial ps3 warning fixes
  ...

This finally adds the PPC_PRPMC2800 Kconfig option, the board setup
code (the setup and reset functions) and the defconfig, to support the
Motorola PrPMC2800 platform.
Signed-off-by: Dale Farnsworth <dale@farnsworth.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>

The Motorola PrPMC280 and PrPMC2800 processor modules sit on an F101 or
PrPMC2800 baseboard, respectively.  There are several variants of each
type of processor module which can have different amounts of memory,
amounts of FLASH, cpu frequencies, and an mv64360 or an mv64362.

The bootwrapper code for that platform reads VPD from an I2C EEPROM
to determine the processor module variant.  From the variant, the
amount of memory, etc. is determined and the device tree is updated
accordingly.  If the variant cannot be determined (e.g., corrupted
VPD or a previously unknown variant), the property values already
in the device tree are used.

Also, the firmware for those platforms does not completely configure
the mv64x60 host bridge so that configuration is done here.
Signed-off-by: Mark A. Greer <mgreer@mvista.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>

Add the device tree source file for the prpmc2800 line of processor PMCs.
Several of the property values are updated by the bootwrapper but sane
defaults have been chosen in case the bootwrapper can't determine the
exact processor board variant.  The defaults should allow the kernel
to boot despite having non-optimal device tree property values.
Signed-off-by: Mark A. Greer <mgreer@mvista.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>

check_cache_coherency() verifies that the cache coherency setting of
the kernel (CONFIG_NOT_COHERENT_CACHE) matches that left by the firmware,
as indicated by coherency-off device tree property.
Signed-off-by: Dale Farnsworth <dale@farnsworth.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>

This patch adds PCI bridge support for the Marvell mv64x60 chip.
We also provide the ability to read/write the mv64x60 hotswap
register via sysfs if the hs_reg_valid property is set in the
device tree.
Signed-off-by: Dale Farnsworth <dale@farnsworth.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Paul Mackerras <paulus@samba.org>

This patch creates platform_device entries for the Marvell mv64x60
I2C ports, based on information contained in device tree.

This driver (like the other mv64x60 drivers) are unusual in that it
works on both the MIPS and PowerPC architectures.  Because of that,
the drivers do not support the normal PowerPC of_platform_bus_type.
They support platform_bus_type instead.
Signed-off-by: Dale Farnsworth <dale@farnsworth.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Paul Mackerras <paulus@samba.org>

This patch creates platform_device entries for the Marvell mv64x60
ethernet controller ports, based on information contained in the
device tree.

This driver (like the other mv64x60 drivers) are unusual in that it
works on both the MIPS and PowerPC architectures.  Because of that,
the drivers do not support the normal PowerPC of_platform_bus_type.
They support platform_bus_type instead.
Signed-off-by: Dale Farnsworth <dale@farnsworth.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Paul Mackerras <paulus@samba.org>

This patch creates platform_device entries for the Marvell mv64x60
MPSC (multi-protocol serial controller) ports, based on information
contained in the device tree.

This driver (like the other mv64x60 drivers) are unusual in that it
works on both the MIPS and PowerPC architectures.  Because of that,
the drivers do not support the normal PowerPC of_platform_bus_type.
They support platform_bus_type instead.
Signed-off-by: Dale Farnsworth <dale@farnsworth.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Paul Mackerras <paulus@samba.org>

There are 3 interrupt groups each with its own status/mask registers.
We use a separate struct irq_chip for each interrupt group and handle
interrupts in two stages or levels: level 1 selects the appropriate
struct irq_chip, and level 2 selects individual interrupts within
that irq_chip.
Signed-off-by: Dale Farnsworth <dale@farnsworth.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>

Some platforms support a variety processor modules with no method of
determining which exact processor module is being used except by
examining Vital Product Data (VPD).  The modules may have different
amounts of memory, clock frequencies, etc. so reading the VPD becomes
necessary to correctly set properties in the device tree before its
passed to the kernel.

Often the VPD is stored in I2C EEPROMs so an I2C driver becomes necessary.
This I2C driver is for the I2C controller that's embedded on the Marvel
mv64x60 line of host bridges.
Signed-off-by: Mark A. Greer <mgreer@mvista.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>

The bootwrapper requires a serial driver to allow cmdline editing
and information reporting on the console.  This driver is required
by platforms that boot a zImage and use the MPSC for the console.
Signed-off-by: Mark A. Greer <mgreer@mvista.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>

The mv64x60 host bridge has many windows between its various components
(cpu, system memory, ethernet ctlr, MPSC, DMA ctlr, PCI MEM, PCI I/O).
Unfortunately, the firmware on some of mv64x60-based platforms do not
properly or completely configure those windows (e.g., MPSC->system memory
windows not configured or CPU->PCI MEM space not configured).

So, the missing configuration needs to be done in either the bootwrapper
or in the kernel.  To keep the kernel as clean as possible, it is done
in the bootwrapper.  Note that I/O controller configuration is NOT being
done, its only the windows to allow the I/O controllers and other components
to access memory, etc. that is being done--drivers assume that their
controllers can already access system memory).

Table of routines and the windows they configure:
	mv64x60_config_ctlr_windows()	ENET->System Memory
					MPSC->System Memory
					IDMA->System Memory

	mv64x60_config_pci_windows()	PCI MEM->System Memory
					PCI I/O->Bridge's Registers

	mv64x60_config_cpu2pci_window()	CPU->PCI MEM
					CPU->PCI I/O
Signed-off-by: Mark A. Greer <mgreer@mvista.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>

Add 'zImage.dts' and 'zImage.dts_initrd' build rules that automatically
compile and wrap a dts file from arch/powerpc/boot/dts into the zImage file.
The resulting zImage will be arch/powerpc/boot/zImage.dts.<platform> and
arch/powerpc/boot/zImage.dts_initrd.<platform>, respectively.

Having separate rules allows the user to choose whether to include a device
tree--and which device tree--at build time.  This is useful when one Makefile
target builds a zImage that runs on several platforms except for differing
device trees.  By just setting CONFIG_DEVICE_TREE and running "make zImage.dts"
the exact zImage you want is built without Makefile bloat or manually running
the wrapper script.

The dts file is expected to be arch/powerpc/boot/dts/$(CONFIG_DEVICE_TREE)
Signed-off-by: Mark A. Greer <mgreer@mvista.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>

Spelling fixes in arch/ppc/.
Signed-off-by: Simon Arlott <simon@fire.lp0.eu>
Signed-off-by: Paul Mackerras <paulus@samba.org>

The boot wrapper platform init code on 83xx and 85xx using the cuboot
platform type was incorrectly assuming that u-boot supplied the size
of the initrd, whereas it actually supplies the end address.  This
fixes it.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>

Update ps3_defconfig.
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>

Fix compiler warning:

ps3/smp.c:122: warning: ignoring return value of 'request_irq'
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>

An mdio bus scan was added with ucc_geth phylib
migration patches, now machines complain on boot, saying:

prom_parse: Bad cell count for /qe@e0100000/mdio@2120/ethernet-phy@00
prom_parse: Bad cell count for /qe@e0100000/mdio@2120/ethernet-phy@01

since size-cells can indeed be 0, this patch fixes the check.
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>

Greatly simplify the function smp_space_timers.

The stolen time calculation (per comment within the code) doesn't need the
half-jiffy stagger any more.  There isn't an issue with bouncing off global
locks, so we really shouldn't need any sort of staggering at all.

However, the last_jiffy value still needs to be set.   This removes the
extra stagger logic, and just sets the values.

This change should benefit applications that rely on barrier
synchronization, and will help cut down OS jitter.

Boot tested across the board (G5,power3,power4,power5,970mp blade).
Signed-off-by: Will Schmidt <will_schmidt@vnet.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>

Fixes warnings:

arch/powerpc/platforms/ps3/system-bus.c: In function 'ps3_map_sg':
arch/powerpc/platforms/ps3/system-bus.c:278: warning: unused variable 'i'
arch/powerpc/platforms/ps3/system-bus.c:277: warning: unused variable 'dev'
arch/powerpc/platforms/ps3/setup.c:103: warning: 'prealloc' defined but not used
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Acked-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>

fixes:
arch/powerpc/platforms/pasemi/idle.c: In function 'pasemi_system_reset_exception':
arch/powerpc/platforms/pasemi/idle.c:55: warning: implicit declaration of function 'do_IRQ'
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>

Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>

This case will never be hit, but it should be corrected anyway.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>

* master.kernel.org:/pub/scm/linux/kernel/git/wim/linux-2.6-watchdog:
  [WATCHDOG] iTCO_wdt.c - fix ACPI Base register

* 'upstream-linus' of master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/libata-dev:
  pata_platform: don't use generic ata_port_start
  Use menuconfig objects: libata
  add the ATI SB700 SATA controller device id to AHCI pci table
  Add the combined mode for ATI SB700
  pata_pcmcia: recognize 2GB CompactFlash from Transcend
  git-libata-all: sata_via build fix
  libata-acpi: clean up parameters and misc stuff
  libata-acpi: s/CONFIG_SATA_ACPI/CONFIG_ATA_ACPI/
  libata: give devices one last chance even if recovery failed with -EINVAL
  libata: fallback to the other IDENTIFY on device error, take#2
  libata: ignore EH scheduling during initialization
  libata: clean up SFF init mess
  libata: implement libata.spindown_compat
  libata: reimplement suspend/resume support using sdev->manage_start_stop

* 'upstream-linus' of master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/netdev-2.6: (35 commits)
  Add support for the Davicom DM9161A PHY
  sky2: only disable 88e8056 on some boards
  sky2: 88e8071 support not ready
  skge: crash on shutdown/suspend
  sky2: fix oops on shutdown
  mlx4: don't use deprecated IRQ flags
  netxen_nic_main don't use deprecated irq flags
  Use menuconfig objects II - netdev/wan
  Use menuconfig objects II - netdev/pcmcia
  Use menuconfig objects II - netdev/atm
  Use menuconfig objects: netdev
  Use menuconfig objects: PHY
  spidernet: remove unnecessary accesses to phy
  S2IO: Statistics for link up/down and memory allocated/freed
  S2IO: statistics for memory allocation failuers
  S2IO: getringparam ethtool option
  [PATCH] libertas: 64-bit cleanups
  [PATCH] libertas: sparse fixes
  [PATCH] libertas: fix missing unlock in TX error path
  [PATCH] libertas: make debugfs.c sparse-clean
  ...

Today's find is a triggered assertion in msi_free_irqs() when the system
doesn't support MSI, in which case arch_setup_msi_irqs() always returns
an error.

The problem is that when this happens we branch into msi_free_irqs(), to
which you added the following assertion loop:

	list_for_each_entry(entry, &dev->msi_list, list)
		BUG_ON(irq_has_action(entry->irq));

Well, if arch_setup_msi_irqs() fails, entry->irq will be zero and
although that's never assigned to any normal devices we use that IRQ
number for the timer interrupt on sparc64 so this assertion triggers.

Better to test for zero before doing the irq_has_action() assertion
thing.
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

I have a system where I have a simple IDE controller that sits on a
local bus without bus master dma capability, and thus no dma_mapping
ops defined for the device/bus.

pata_platform works great for me, with the exception of using the generic
ata_port_start which tries to do a dmam_alloc_coherent.

Looks like it doesn't need to allocate a prd table at all, so replace it
with a dummy function instead.
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

Use menuconfigs instead of menus, so the whole menu can be disabled at once
instead of going through all options.
Signed-off-by: Jan Engelhardt <jengelh@gmx.de>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

Add the device ID to AHCI pci table for ATI SB700 SATA controller, the
subsequent chipset of SB600.

Signed-off-by: henry su<henry.su@amd.com>
Cc: Jeff Garzik <jeff@garzik.org>
Cc: Tejun Heo <htejun@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

Besides those modes in ATI SB600 SATA controller, ATI SB700 supports one
more mode:the combined mode.

The combined mode is a Legacy IDE mode used for compatibility with some old
OS without AHCI driver, but now it is not necessary for Linux since the
kernel has supported AHCI.
Signed-off-by: Luugi Marsan <luugi.marsan@amd.com>
Cc: Jeff Garzik <jeff@garzik.org>
Cc: Tejun Heo <htejun@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

Allow the pata_pcmcia driver to automatically detect 2GB CompactFlash cards
from Transcend.
Signed-off-by: Fabrice Aeschbacher <fabrice.aeschbacher@siemens.com>
Cc: "Peter Stuge" <stuge-linux-pcmcia@cdy.org>
Acked-by: Alan Cox <alan@redhat.com>
Cc: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

Cc: Tejun Heo <htejun@gmail.com>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

This patch cleans up libata-acpi such that it looks similar to other
libata files.  This patch doesn't introuce any behavior changes.

* make libata-acpi functions take ata_device instead of ata_port +
  device index
* s/atadev/dev/
* de-indent local variable declarations
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

ACPI applies to both SATA and PATA.  Drop the 'S' from the config
variable.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

After certain errors, some devices report complete garbage on
IDENTIFY.  This can cause ata_dev_read_id() to fail with -EINVAL
resulting in immediate disabling of the device.  Give the device one
last chance after -EINVAL to allow recovery from such situations.  As
-EINVAL is triggered very rarely, this shouldn't cause any noticeable
affect on more common error paths.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: Harald Dunkel <harald.dunkel@t-online.de>
Signed-off-by: Jeff Garzik <jeff@garzik.org>