- 16 Aug, 2017 8 commits
-
-
Varun Prakash authored
commit ea8dc5b4 upstream. On receiving text request iscsi-target allocates buffer for payload in iscsit_handle_text_cmd() and assigns buffer pointer to cmd->text_in_ptr, this buffer is currently freed in iscsit_release_cmd(), if iscsi-target sets 'C' bit in text response then it will receive another text request from the initiator with ttt != 0xffffffff in this case iscsi-target will find cmd using itt and call iscsit_setup_text_cmd() which will set cmd->text_in_ptr to NULL without freeing previously allocated buffer. This patch fixes this issue by calling kfree(cmd->text_in_ptr) in iscsit_setup_text_cmd() before assigning NULL to it. For the first text request cmd->text_in_ptr is NULL as cmd is memset to 0 in iscsit_allocate_cmd(). Signed-off-by:
Varun Prakash <varun@chelsio.com> Signed-off-by:
Nicholas Bellinger <nab@linux-iscsi.org> Signed-off-by:
Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Boris Brezillon authored
commit a11bf5ed upstream. Some ONFI NANDs do not support the SET/GET FEATURES commands, which, according to the spec, is perfectly valid. On these NANDs we can't set a specific timing mode using the "timing mode" feature, and we should assume the NAND does not require any setup to enter a specific timing mode. Signed-off-by:
Boris Brezillon <boris.brezillon@free-electrons.com> Fixes: d8e725dd ("mtd: nand: automate NAND timings selection") Reported-by:
Alexander Dahl <ada@thorsis.com> Tested-by:
-
Max Filippov authored
commit 7f81e55c upstream. csum_partial and csum_partial_copy_generic are defined unconditionally and are available even when CONFIG_NET is disabled. They are used not only by the network drivers, but also by scsi and media. Don't limit these functions export by CONFIG_NET. Signed-off-by:
Max Filippov <jcmvbkbc@gmail.com> Signed-off-by:
-
Max Filippov authored
commit bc652eb6 upstream. Functions clear_user_highpage, copy_user_highpage, flush_dcache_page, local_flush_cache_range and local_flush_cache_page may be used from modules. Export them. Signed-off-by:
-
Max Filippov authored
commit 6d0f581d upstream. Currently building kernel for xtensa core with aliasing WT cache fails with the following messages: mm/memory.c:2152: undefined reference to `flush_dcache_page' mm/memory.c:2332: undefined reference to `local_flush_cache_page' mm/memory.c:1919: undefined reference to `local_flush_cache_range' mm/memory.c:4179: undefined reference to `copy_to_user_page' mm/memory.c:4183: undefined reference to `copy_from_user_page' This happens because implementation of these functions is only compiled when data cache is WB, which looks wrong: even when data cache doesn't need flushing it still needs invalidation. The functions like __flush_[invalidate_]dcache_* are correctly defined for both WB and WT caches (and even if they weren't that'd still be ok, just slower). Fix this by providing the same implementation of the above functions for both WB and WT cache. Signed-off-by:
-
Mel Gorman authored
commit 48fb6f4d upstream. Commit 65d8fc77 ("futex: Remove requirement for lock_page() in get_futex_key()") removed an unnecessary lock_page() with the side-effect that page->mapping needed to be treated very carefully. Two defensive warnings were added in case any assumption was missed and the first warning assumed a correct application would not alter a mapping backing a futex key. Since merging, it has not triggered for any unexpected case but Mark Rutland reported the following bug triggering due to the first warning. kernel BUG at kernel/futex.c:679! Internal error: Oops - BUG: 0 [#1] PREEMPT SMP Modules linked in: CPU: 0 PID: 3695 Comm: syz-executor1 Not tainted 4.13.0-rc3-00020-g307fec773ba3 #3 Hardware name: linux,dummy-virt (DT) task: ffff80001e271780 task.stack: ffff000010908000 PC is at get_futex_key+0x6a4/0xcf0 kernel/futex.c:679 LR is at get_futex_key+0x6a4/0xcf0 kernel/futex.c:679 pc : [<ffff00000821ac14>] lr : [<ffff00000821ac14>] pstate: 80000145 The fact that it's a bug instead of a warning was due to an unrelated arm64 problem, but the warning itself triggered because the underlying mapping changed. This is an application issue but from a kernel perspective it's a recoverable situation and the warning is unnecessary so this patch removes the warning. The warning may potentially be triggered with the following test program from Mark although it may be necessary to adjust NR_FUTEX_THREADS to be a value smaller than the number of CPUs in the system. #include <linux/futex.h> #include <pthread.h> #include <stdio.h> #include <stdlib.h> #include <sys/mman.h> #include <sys/syscall.h> #include <sys/time.h> #include <unistd.h> #define NR_FUTEX_THREADS 16 pthread_t threads[NR_FUTEX_THREADS]; void *mem; #define MEM_PROT (PROT_READ | PROT_WRITE) #define MEM_SIZE 65536 static int futex_wrapper(int *uaddr, int op, int val, const struct timespec *timeout, int *uaddr2, int val3) { syscall(SYS_futex, uaddr, op, val, timeout, uaddr2, val3); } void *poll_futex(void *unused) { for (;;) { futex_wrapper(mem, FUTEX_CMP_REQUEUE_PI, 1, NULL, mem + 4, 1); } } int main(int argc, char *argv[]) { int i; mem = mmap(NULL, MEM_SIZE, MEM_PROT, MAP_SHARED | MAP_ANONYMOUS, -1, 0); printf("Mapping @ %p\n", mem); printf("Creating futex threads...\n"); for (i = 0; i < NR_FUTEX_THREADS; i++) pthread_create(&threads[i], NULL, poll_futex, NULL); printf("Flipping mapping...\n"); for (;;) { mmap(mem, MEM_SIZE, MEM_PROT, MAP_FIXED | MAP_SHARED | MAP_ANONYMOUS, -1, 0); } return 0; } Reported-and-tested-by:
Mark Rutland <mark.rutland@arm.com> Signed-off-by:
Mel Gorman <mgorman@suse.de> Acked-by:
Peter Zijlstra (Intel) <peterz@infradead.org> Signed-off-by:
Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by:
-
Cong Wang authored
commit d041353d upstream. We saw many list corruption warnings on shmem shrinklist: WARNING: CPU: 18 PID: 177 at lib/list_debug.c:59 __list_del_entry+0x9e/0xc0 list_del corruption. prev->next should be ffff9ae5694b82d8, but was ffff9ae5699ba960 Modules linked in: intel_rapl sb_edac edac_core x86_pkg_temp_thermal coretemp iTCO_wdt iTCO_vendor_support crct10dif_pclmul crc32_pclmul ghash_clmulni_intel raid0 dcdbas shpchp wmi hed i2c_i801 ioatdma lpc_ich i2c_smbus acpi_cpufreq tcp_diag inet_diag sch_fq_codel ipmi_si ipmi_devintf ipmi_msghandler igb ptp crc32c_intel pps_core i2c_algo_bit i2c_core dca ipv6 crc_ccitt CPU: 18 PID: 177 Comm: kswapd1 Not tainted 4.9.34-t3.el7.twitter.x86_64 #1 Hardware name: Dell Inc. PowerEdge C6220/0W6W6G, BIOS 2.2.3 11/07/2013 Call Trace: dump_stack+0x4d/0x66 __warn+0xcb/0xf0 warn_slowpath_fmt+0x4f/0x60 __list_del_entry+0x9e/0xc0 shmem_unused_huge_shrink+0xfa/0x2e0 shmem_unused_huge_scan+0x20/0x30 super_cache_scan+0x193/0x1a0 shrink_slab.part.41+0x1e3/0x3f0 shrink_slab+0x29/0x30 shrink_node+0xf9/0x2f0 kswapd+0x2d8/0x6c0 kthread+0xd7/0xf0 ret_from_fork+0x22/0x30 WARNING: CPU: 23 PID: 639 at lib/list_debug.c:33 __list_add+0x89/0xb0 list_add corruption. prev->next should be next (ffff9ae5699ba960), but was ffff9ae5694b82d8. (prev=ffff9ae5694b82d8). Modules linked in: intel_rapl sb_edac edac_core x86_pkg_temp_thermal coretemp iTCO_wdt iTCO_vendor_support crct10dif_pclmul crc32_pclmul ghash_clmulni_intel raid0 dcdbas shpchp wmi hed i2c_i801 ioatdma lpc_ich i2c_smbus acpi_cpufreq tcp_diag inet_diag sch_fq_codel ipmi_si ipmi_devintf ipmi_msghandler igb ptp crc32c_intel pps_core i2c_algo_bit i2c_core dca ipv6 crc_ccitt CPU: 23 PID: 639 Comm: systemd-udevd Tainted: G W 4.9.34-t3.el7.twitter.x86_64 #1 Hardware name: Dell Inc. PowerEdge C6220/0W6W6G, BIOS 2.2.3 11/07/2013 Call Trace: dump_stack+0x4d/0x66 __warn+0xcb/0xf0 warn_slowpath_fmt+0x4f/0x60 __list_add+0x89/0xb0 shmem_setattr+0x204/0x230 notify_change+0x2ef/0x440 do_truncate+0x5d/0x90 path_openat+0x331/0x1190 do_filp_open+0x7e/0xe0 do_sys_open+0x123/0x200 SyS_open+0x1e/0x20 do_syscall_64+0x61/0x170 entry_SYSCALL64_slow_path+0x25/0x25 The problem is that shmem_unused_huge_shrink() moves entries from the global sbinfo->shrinklist to its local lists and then releases the spinlock. However, a parallel shmem_setattr() could access one of these entries directly and add it back to the global shrinklist if it is removed, with the spinlock held. The logic itself looks solid since an entry could be either in a local list or the global list, otherwise it is removed from one of them by list_del_init(). So probably the race condition is that, one CPU is in the middle of INIT_LIST_HEAD() but the other CPU calls list_empty() which returns true too early then the following list_add_tail() sees a corrupted entry. list_empty_careful() is designed to fix this situation. [akpm@linux-foundation.org: add comments] Link: http://lkml.kernel.org/r/20170803054630.18775-1-xiyou.wangcong@gmail.com Fixes: 779750d2 ("shmem: split huge pages beyond i_size under memory pressure") Signed-off-by:
Cong Wang <xiyou.wangcong@gmail.com> Acked-by:
Kirill A. Shutemov <kirill.shutemov@linux.intel.com> Cc: Hugh Dickins <hughd@google.com> Signed-off-by:
Andrew Morton <akpm@linux-foundation.org> Signed-off-by:
-
Jonathan Toppins authored
commit 75dddef3 upstream. The RDMA subsystem can generate several thousand of these messages per second eventually leading to a kernel crash. Ratelimit these messages to prevent this crash. Doug said: "I've been carrying a version of this for several kernel versions. I don't remember when they started, but we have one (and only one) class of machines: Dell PE R730xd, that generate these errors. When it happens, without a rate limit, we get rcu timeouts and kernel oopses. With the rate limit, we just get a lot of annoying kernel messages but the machine continues on, recovers, and eventually the memory operations all succeed" And: "> Well... why are all these EBUSY's occurring? It sounds inefficient > (at least) but if it is expected, normal and unavoidable then > perhaps we should just remove that message altogether? I don't have an answer to that question. To be honest, I haven't looked real hard. We never had this at all, then it started out of the blue, but only on our Dell 730xd machines (and it hits all of them), but no other classes or brands of machines. And we have our 730xd machines loaded up with different brands and models of cards (for instance one dedicated to mlx4 hardware, one for qib, one for mlx5, an ocrdma/cxgb4 combo, etc), so the fact that it hit all of the machines meant it wasn't tied to any particular brand/model of RDMA hardware. To me, it always smelled of a hardware oddity specific to maybe the CPUs or mainboard chipsets in these machines, so given that I'm not an mm expert anyway, I never chased it down. A few other relevant details: it showed up somewhere around 4.8/4.9 or thereabouts. It never happened before, but the prinkt has been there since the 3.18 days, so possibly the test to trigger this message was changed, or something else in the allocator changed such that the situation started happening on these machines? And, like I said, it is specific to our 730xd machines (but they are all identical, so that could mean it's something like their specific ram configuration is causing the allocator to hit this on these machine but not on other machines in the cluster, I don't want to say it's necessarily the model of chipset or CPU, there are other bits of identicalness between these machines)" Link: http://lkml.kernel.org/r/499c0f6cc10d6eb829a67f2a4d75b4228a9b356e.1501695897.git.jtoppins@redhat.comSigned-off-by:
Jonathan Toppins <jtoppins@redhat.com> Reviewed-by:
Doug Ledford <dledford@redhat.com> Tested-by:
-
- 13 Aug, 2017 18 commits
-
-
Greg Kroah-Hartman authored
-
Greg Kroah-Hartman authored
This reverts commit 1e9e7178 which is commit 661ccdc1 upstream. It's not needed in 4.9, and it breaks the build. Reported-by:
Guenter Roeck <linux@roeck-us.net> Cc: Milo Kim <woogyom.kim@gmail.com> Cc: Maxime Ripard <maxime.ripard@free-electrons.com> Cc: Sasha Levin <alexander.levin@verizon.com> Signed-off-by:
-
Suzuki K Poulose authored
commit 7e5a6722 upstream. The mmu_notifier_release() callback of KVM triggers cleaning up the stage2 page table on kvm-arm. However there could be other notifier callbacks in parallel with the mmu_notifier_release(), which could cause the call backs ending up in an empty stage2 page table. Make sure we check it for all the notifier callbacks. Fixes: commit 293f2936 ("kvm-arm: Unmap shadow pagetables properly") Reported-by:
Alex Graf <agraf@suse.de> Reviewed-by:
Christoffer Dall <cdall@linaro.org> Signed-off-by:
Suzuki K Poulose <suzuki.poulose@arm.com> Signed-off-by:
Marc Zyngier <marc.zyngier@arm.com> Signed-off-by:
-
Rob Gardner authored
commit fc290a11 upstream. This fixes another cause of random segfaults and bus errors that may occur while running perf with the callgraph option. Critical sections beginning with spin_lock_irqsave() raise the interrupt level to PIL_NORMAL_MAX (14) and intentionally do not block performance counter interrupts, which arrive at PIL_NMI (15). But some sections of code are "super critical" with respect to perf because the perf_callchain_user() path accesses user space and may cause TLB activity as well as faults as it unwinds the user stack. One particular critical section occurs in switch_mm: spin_lock_irqsave(&mm->context.lock, flags); ... load_secondary_context(mm); tsb_context_switch(mm); ... spin_unlock_irqrestore(&mm->context.lock, flags); If a perf interrupt arrives in between load_secondary_context() and tsb_context_switch(), then perf_callchain_user() could execute with the context ID of one process, but with an active TSB for a different process. When the user stack is accessed, it is very likely to incur a TLB miss, since the h/w context ID has been changed. The TLB will then be reloaded with a translation from the TSB for one process, but using a context ID for another process. This exposes memory from one process to another, and since it is a mapping for stack memory, this usually causes the new process to crash quickly. This super critical section needs more protection than is provided by spin_lock_irqsave() since perf interrupts must not be allowed in. Since __tsb_context_switch already goes through the trouble of disabling interrupts completely, we fix this by moving the secondary context load down into this better protected region. Orabug: 25577560 Signed-off-by:
Dave Aldridge <david.j.aldridge@oracle.com> Signed-off-by:
Rob Gardner <rob.gardner@oracle.com> Signed-off-by:
David S. Miller <davem@davemloft.net> Signed-off-by:
-
Willem de Bruijn authored
[ Upstream commit 85f1bd9a ] When iteratively building a UDP datagram with MSG_MORE and that datagram exceeds MTU, consistently choose UFO or fragmentation. Once skb_is_gso, always apply ufo. Conversely, once a datagram is split across multiple skbs, do not consider ufo. Sendpage already maintains the first invariant, only add the second. IPv6 does not have a sendpage implementation to modify. A gso skb must have a partial checksum, do not follow sk_no_check_tx in udp_send_skb. Found by syzkaller. Fixes: e89e9cf5 ("[IPv4/IPv6]: UFO Scatter-gather approach") Reported-by:
Andrey Konovalov <andreyknvl@google.com> Signed-off-by:
Willem de Bruijn <willemb@google.com> Signed-off-by:
-
Greg Kroah-Hartman authored
revert "ipv4: Should use consistent conditional judgement for ip fragment in __ip_append_data and ip_finish_output" This reverts commit f102bb71 which is commit 0a28cfd5 upstream as there is another patch that needs to be applied instead of this one. Cc: Zheng Li <james.z.li@ericsson.com> Cc: David S. Miller <davem@davemloft.net> Cc: Sasha Levin <alexander.levin@verizon.com> Signed-off-by:
-
Greg Kroah-Hartman authored
This reverts commit ef09c9ff which is commit a5cb659b upstream as it causes merge issues with later patches that are much more important... Cc: Michal Kubecek <mkubecek@suse.cz> Cc: Vlad Yasevich <vyasevic@redhat.com> Cc: David S. Miller <davem@davemloft.net> Cc: Sasha Levin <alexander.levin@verizon.com> Signed-off-by:
-
Willem de Bruijn authored
[ Upstream commit c27927e3 ] Updates to tp_reserve can race with reads of the field in packet_set_ring. Avoid this by holding the socket lock during updates in setsockopt PACKET_RESERVE. This bug was discovered by syzkaller. Fixes: 8913336a ("packet: add PACKET_RESERVE sockopt") Reported-by:
-
Nikolay Borisov authored
[ Upstream commit 1714020e ] Commit dcd87999 ("igmp: net: Move igmp namespace init to correct file") moved the igmp sysctls initialization from tcp_sk_init to igmp_net_init. This function is only called as part of per-namespace initialization, only if CONFIG_IP_MULTICAST is defined, otherwise igmp_mc_init() call in ip_init is compiled out, casuing the igmp pernet ops to not be registerd and those sysctl being left initialized with 0. However, there are certain functions, such as ip_mc_join_group which are always compiled and make use of some of those sysctls. Let's do a partial revert of the aforementioned commit and move the sysctl initialization into inet_init_net, that way they will always have sane values. Fixes: dcd87999 ("igmp: net: Move igmp namespace init to correct file") Link: https://bugzilla.kernel.org/show_bug.cgi?id=196595Reported-by:
Gerardo Exequiel Pozzi <vmlinuz386@gmail.com> Signed-off-by:
Nikolay Borisov <nborisov@suse.com> Signed-off-by:
-
Willem de Bruijn authored
[ Upstream commit 8d63bee6 ] skb_warn_bad_offload triggers a warning when an skb enters the GSO stack at __skb_gso_segment that does not have CHECKSUM_PARTIAL checksum offload set. Commit b2504a5d ("net: reduce skb_warn_bad_offload() noise") observed that SKB_GSO_DODGY producers can trigger the check and that passing those packets through the GSO handlers will fix it up. But, the software UFO handler will set ip_summed to CHECKSUM_NONE. When __skb_gso_segment is called from the receive path, this triggers the warning again. Make UFO set CHECKSUM_UNNECESSARY instead of CHECKSUM_NONE. On Tx these two are equivalent. On Rx, this better matches the skb state (checksum computed), as CHECKSUM_NONE here means no checksum computed. See also this thread for context: http://patchwork.ozlabs.org/patch/799015/ Fixes: b2504a5d ("net: reduce skb_warn_bad_offload() noise") Signed-off-by:
-
Eric Dumazet authored
[ Upstream commit 8ba60924 ] With new TCP_FASTOPEN_CONNECT socket option, there is a possibility to call tcp_connect() while socket sk_dst_cache is either NULL or invalid. +0 socket(..., SOCK_STREAM, IPPROTO_TCP) = 4 +0 fcntl(4, F_SETFL, O_RDWR|O_NONBLOCK) = 0 +0 setsockopt(4, SOL_TCP, TCP_FASTOPEN_CONNECT, [1], 4) = 0 +0 connect(4, ..., ...) = 0 << sk->sk_dst_cache becomes obsolete, or even set to NULL >> +1 sendto(4, ..., 1000, MSG_FASTOPEN, ..., ...) = 1000 We need to refresh the route otherwise bad things can happen, especially when syzkaller is running on the host :/ Fixes: 19f6d3f3 ("net/tcp-fastopen: Add new API support") Reported-by:
Dmitry Vyukov <dvyukov@google.com> Signed-off-by:
Eric Dumazet <edumazet@google.com> Cc: Wei Wang <weiwan@google.com> Cc: Yuchung Cheng <ycheng@google.com> Acked-by:
Wei Wang <weiwan@google.com> Acked-by:
Yuchung Cheng <ycheng@google.com> Signed-off-by:
-
Xin Long authored
[ Upstream commit 96d97030 ] Commit 55917a21 ("netfilter: x_tables: add context to know if extension runs from nft_compat") introduced a member nft_compat to xt_tgchk_param structure. But it didn't set it's value for ipt_init_target. With unexpected value in par.nft_compat, it may return unexpected result in some target's checkentry. This patch is to set all it's fields as 0 and only initialize the non-zero fields in ipt_init_target. v1->v2: As Wang Cong's suggestion, fix it by setting all it's fields as 0 and only initializing the non-zero fields. Fixes: 55917a21 ("netfilter: x_tables: add context to know if extension runs from nft_compat") Suggested-by:
Xin Long <lucien.xin@gmail.com> Signed-off-by:
-
Davide Caratti authored
[ Upstream commit e718fe45 ] if the NIC fails to validate the checksum on TCP/UDP, and validation of IP checksum is successful, the driver subtracts the pseudo-header checksum from the value obtained by the hardware and sets CHECKSUM_COMPLETE. Don't do that if protocol is IPPROTO_SCTP, otherwise CRC32c validation fails. V2: don't test MLX4_CQE_STATUS_IPV6 if MLX4_CQE_STATUS_IPV4 is set Reported-by:
Shuang Li <shuali@redhat.com> Fixes: f8c6455b ("net/mlx4_en: Extend checksum offloading by CHECKSUM COMPLETE") Signed-off-by:
Davide Caratti <dcaratti@redhat.com> Acked-by:
Saeed Mahameed <saeedm@mellanox.com> Signed-off-by:
-
Daniel Borkmann authored
[ Upstream commit b0a0c256 ] While testing some other work that required JIT modifications, I run into test_bpf causing a hang when JIT enabled on s390. The problematic test case was the one from ddc665a4 (bpf, arm64: fix jit branch offset related to ldimm64), and turns out that we do have a similar issue on s390 as well. In bpf_jit_prog() we update next instruction address after returning from bpf_jit_insn() with an insn_count. bpf_jit_insn() returns either -1 in case of error (e.g. unsupported insn), 1 or 2. The latter is only the case for ldimm64 due to spanning 2 insns, however, next address is only set to i + 1 not taking actual insn_count into account, thus fix is to use insn_count instead of 1. bpf_jit_enable in mode 2 provides also disasm on s390: Before fix: 000003ff800349b6: a7f40003 brc 15,3ff800349bc ; target 000003ff800349ba: 0000 unknown 000003ff800349bc: e3b0f0700024 stg %r11,112(%r15) 000003ff800349c2: e3e0f0880024 stg %r14,136(%r15) 000003ff800349c8: 0db0 basr %r11,%r0 000003ff800349ca: c0ef00000000 llilf %r14,0 000003ff800349d0: e320b0360004 lg %r2,54(%r11) 000003ff800349d6: e330b03e0004 lg %r3,62(%r11) 000003ff800349dc: ec23ffeda065 clgrj %r2,%r3,10,3ff800349b6 ; jmp 000003ff800349e2: e3e0b0460004 lg %r14,70(%r11) 000003ff800349e8: e3e0b04e0004 lg %r14,78(%r11) 000003ff800349ee: b904002e lgr %r2,%r14 000003ff800349f2: e3b0f0700004 lg %r11,112(%r15) 000003ff800349f8: e3e0f0880004 lg %r14,136(%r15) 000003ff800349fe: 07fe bcr 15,%r14 After fix: 000003ff80ef3db4: a7f40003 brc 15,3ff80ef3dba 000003ff80ef3db8: 0000 unknown 000003ff80ef3dba: e3b0f0700024 stg %r11,112(%r15) 000003ff80ef3dc0: e3e0f0880024 stg %r14,136(%r15) 000003ff80ef3dc6: 0db0 basr %r11,%r0 000003ff80ef3dc8: c0ef00000000 llilf %r14,0 000003ff80ef3dce: e320b0360004 lg %r2,54(%r11) 000003ff80ef3dd4: e330b03e0004 lg %r3,62(%r11) 000003ff80ef3dda: ec230006a065 clgrj %r2,%r3,10,3ff80ef3de6 ; jmp 000003ff80ef3de0: e3e0b0460004 lg %r14,70(%r11) 000003ff80ef3de6: e3e0b04e0004 lg %r14,78(%r11) ; target 000003ff80ef3dec: b904002e lgr %r2,%r14 000003ff80ef3df0: e3b0f0700004 lg %r11,112(%r15) 000003ff80ef3df6: e3e0f0880004 lg %r14,136(%r15) 000003ff80ef3dfc: 07fe bcr 15,%r14 test_bpf.ko suite runs fine after the fix. Fixes: 05462310 ("s390/bpf: Add s390x eBPF JIT compiler backend") Signed-off-by:
Daniel Borkmann <daniel@iogearbox.net> Tested-by:
Michael Holzheu <holzheu@linux.vnet.ibm.com> Signed-off-by:
-
Eric Dumazet authored
[ Upstream commit 2dda6400 ] syzkaller was able to trigger a divide by 0 in TCP stack [1] Issue here is that keepalive timer needs to be updated to not attempt to send a probe if the connection setup was deferred using TCP_FASTOPEN_CONNECT socket option added in linux-4.11 [1] divide error: 0000 [#1] SMP CPU: 18 PID: 0 Comm: swapper/18 Not tainted task: ffff986f62f4b040 ti: ffff986f62fa2000 task.ti: ffff986f62fa2000 RIP: 0010:[<ffffffff8409cc0d>] [<ffffffff8409cc0d>] __tcp_select_window+0x8d/0x160 Call Trace: <IRQ> [<ffffffff8409d951>] tcp_transmit_skb+0x11/0x20 [<ffffffff8409da21>] tcp_xmit_probe_skb+0xc1/0xe0 [<ffffffff840a0ee8>] tcp_write_wakeup+0x68/0x160 [<ffffffff840a151b>] tcp_keepalive_timer+0x17b/0x230 [<ffffffff83b3f799>] call_timer_fn+0x39/0xf0 [<ffffffff83b40797>] run_timer_softirq+0x1d7/0x280 [<ffffffff83a04ddb>] __do_softirq+0xcb/0x257 [<ffffffff83ae03ac>] irq_exit+0x9c/0xb0 [<ffffffff83a04c1a>] smp_apic_timer_interrupt+0x6a/0x80 [<ffffffff83a03eaf>] apic_timer_interrupt+0x7f/0x90 <EOI> [<ffffffff83fed2ea>] ? cpuidle_enter_state+0x13a/0x3b0 [<ffffffff83fed2cd>] ? cpuidle_enter_state+0x11d/0x3b0 Tested: Following packetdrill no longer crashes the kernel `echo 0 >/proc/sys/net/ipv4/tcp_timestamps` // Cache warmup: send a Fast Open cookie request 0 socket(..., SOCK_STREAM, IPPROTO_TCP) = 3 +0 fcntl(3, F_SETFL, O_RDWR|O_NONBLOCK) = 0 +0 setsockopt(3, SOL_TCP, TCP_FASTOPEN_CONNECT, [1], 4) = 0 +0 connect(3, ..., ...) = -1 EINPROGRESS (Operation is now in progress) +0 > S 0:0(0) <mss 1460,nop,nop,sackOK,nop,wscale 8,FO,nop,nop> +.01 < S. 123:123(0) ack 1 win 14600 <mss 1460,nop,nop,sackOK,nop,wscale 6,FO abcd1234,nop,nop> +0 > . 1:1(0) ack 1 +0 close(3) = 0 +0 > F. 1:1(0) ack 1 +0 < F. 1:1(0) ack 2 win 92 +0 > . 2:2(0) ack 2 +0 socket(..., SOCK_STREAM, IPPROTO_TCP) = 4 +0 fcntl(4, F_SETFL, O_RDWR|O_NONBLOCK) = 0 +0 setsockopt(4, SOL_TCP, TCP_FASTOPEN_CONNECT, [1], 4) = 0 +0 setsockopt(4, SOL_SOCKET, SO_KEEPALIVE, [1], 4) = 0 +.01 connect(4, ..., ...) = 0 +0 setsockopt(4, SOL_TCP, TCP_KEEPIDLE, [5], 4) = 0 +10 close(4) = 0 `echo 1 >/proc/sys/net/ipv4/tcp_timestamps` Fixes: 19f6d3f3 ("net/tcp-fastopen: Add new API support") Signed-off-by:
-
Yuchung Cheng authored
[ Upstream commit ed254971 ] If the sender switches the congestion control during ECN-triggered cwnd-reduction state (CA_CWR), upon exiting recovery cwnd is set to the ssthresh value calculated by the previous congestion control. If the previous congestion control is BBR that always keep ssthresh to TCP_INIFINITE_SSTHRESH, cwnd ends up being infinite. The safe step is to avoid assigning invalid ssthresh value when recovery ends. Signed-off-by:
Neal Cardwell <ncardwell@google.com> Acked-by:
-
Guillaume Nault authored
[ Upstream commit 0a0e1a85 ] Commit e5dadc65 ("ppp: Fix false xmit recursion detect with two ppp devices") dropped the xmit_recursion counter incrementation in ppp_channel_push() and relied on ppp_xmit_process() for this task. But __ppp_channel_push() can also send packets directly (using the .start_xmit() channel callback), in which case the xmit_recursion counter isn't incremented anymore. If such packets get routed back to the parent ppp unit, ppp_xmit_process() won't notice the recursion and will call ppp_channel_push() on the same channel, effectively creating the deadlock situation that the xmit_recursion mechanism was supposed to prevent. This patch re-introduces the xmit_recursion counter incrementation in ppp_channel_push(). Since the xmit_recursion variable is now part of the parent ppp unit, incrementation is skipped if the channel doesn't have any. This is fine because only packets routed through the parent unit may enter the channel recursively. Finally, we have to ensure that pch->ppp is not going to be modified while executing ppp_channel_push(). Instead of taking this lock only while calling ppp_xmit_process(), we now have to hold it for the full ppp_channel_push() execution. This respects the ppp locks ordering which requires locking ->upl before ->downl. Fixes: e5dadc65 ("ppp: Fix false xmit recursion detect with two ppp devices") Signed-off-by:
Guillaume Nault <g.nault@alphalink.fr> Signed-off-by:
-
Gao Feng authored
[ Upstream commit e5dadc65 ] The global percpu variable ppp_xmit_recursion is used to detect the ppp xmit recursion to avoid the deadlock, which is caused by one CPU tries to lock the xmit lock twice. But it would report false recursion when one CPU wants to send the skb from two different PPP devices, like one L2TP on the PPPoE. It is a normal case actually. Now use one percpu member of struct ppp instead of the gloable variable to detect the xmit recursion of one ppp device. Fixes: 55454a56 ("ppp: avoid dealock on recursive xmit") Signed-off-by:
Gao Feng <gfree.wind@vip.163.com> Signed-off-by:
Liu Jianying <jianying.liu@ikuai8.com> Signed-off-by:
-
- 11 Aug, 2017 14 commits
-
-
Greg Kroah-Hartman authored
-
Tejun Heo authored
commit 0a94efb5 upstream. 5c0338c6 ("workqueue: restore WQ_UNBOUND/max_active==1 to be ordered") automatically enabled ordered attribute for unbound workqueues w/ max_active == 1. Because ordered workqueues reject max_active and some attribute changes, this implicit ordered mode broke cases where the user creates an unbound workqueue w/ max_active == 1 and later explicitly changes the related attributes. This patch distinguishes explicit and implicit ordered setting and overrides from attribute changes if implict. Signed-off-by:
Tejun Heo <tj@kernel.org> Fixes: 5c0338c6 ("workqueue: restore WQ_UNBOUND/max_active==1 to be ordered") Cc: Holger Hoffstätte <holger@applied-asynchrony.com> Signed-off-by:
-
Florian Fainelli authored
commit 7b9a88a3 upstream. The PHY library does not deal very well with bind and unbind events. The first thing we would see is that we were not properly canceling the PHY state machine workqueue, so we would be crashing while dereferencing phydev->drv since there is no driver attached anymore. Suggested-by:
Russell King <rmk+kernel@armlinux.org.uk> Signed-off-by:
Florian Fainelli <f.fainelli@gmail.com> Signed-off-by:
-
Michal Kubeček authored
[ Upstream commit a5cb659b ] Our customer encountered stuck NFS writes for blocks starting at specific offsets w.r.t. page boundary caused by networking stack sending packets via UFO enabled device with wrong checksum. The problem can be reproduced by composing a long UDP datagram from multiple parts using MSG_MORE flag: sendto(sd, buff, 1000, MSG_MORE, ...); sendto(sd, buff, 1000, MSG_MORE, ...); sendto(sd, buff, 3000, 0, ...); Assume this packet is to be routed via a device with MTU 1500 and NETIF_F_UFO enabled. When second sendto() gets into __ip_append_data(), this condition is tested (among others) to decide whether to call ip_ufo_append_data(): ((length + fragheaderlen) > mtu) || (skb && skb_is_gso(skb)) At the moment, we already have skb with 1028 bytes of data which is not marked for GSO so that the test is false (fragheaderlen is usually 20). Thus we append second 1000 bytes to this skb without invoking UFO. Third sendto(), however, has sufficient length to trigger the UFO path so that we end up with non-UFO skb followed by a UFO one. Later on, udp_send_skb() uses udp_csum() to calculate the checksum but that assumes all fragments have correct checksum in skb->csum which is not true for UFO fragments. When checking against MTU, we need to add skb->len to length of new segment if we already have a partially filled skb and fragheaderlen only if there isn't one. In the IPv6 case, skb can only be null if this is the first segment so that we have to use headersize (length of the first IPv6 header) rather than fragheaderlen (length of IPv6 header of further fragments) for skb == NULL. Fixes: e89e9cf5 ("[IPv4/IPv6]: UFO Scatter-gather approach") Fixes: e4c5e13a ("ipv6: Should use consistent conditional judgement for ip6 fragment between __ip6_append_data and ip6_finish_output") Signed-off-by:
Michal Kubecek <mkubecek@suse.cz> Acked-by:
Vlad Yasevich <vyasevic@redhat.com> Signed-off-by:
Sasha Levin <alexander.levin@verizon.com> Signed-off-by:
-
zheng li authored
ipv4: Should use consistent conditional judgement for ip fragment in __ip_append_data and ip_finish_output [ Upstream commit 0a28cfd5 ] There is an inconsistent conditional judgement in __ip_append_data and ip_finish_output functions, the variable length in __ip_append_data just include the length of application's payload and udp header, don't include the length of ip header, but in ip_finish_output use (skb->len > ip_skb_dst_mtu(skb)) as judgement, and skb->len include the length of ip header. That causes some particular application's udp payload whose length is between (MTU - IP Header) and MTU were fragmented by ip_fragment even though the rst->dev support UFO feature. Add the length of ip header to length in __ip_append_data to keep consistent conditional judgement as ip_finish_output for ip fragment. Signed-off-by:
Zheng Li <james.z.li@ericsson.com> Signed-off-by:
-
Or Gerlitz authored
[ Upstream commit 5bae8c03 ] We must re-enable RoCE on the e-switch management port (PF) only after destroying the FDB in its switchdev/offloaded mode. Otherwise, when encapsulation is supported, this re-enablement will fail. Also, it's more natural and symmetric to disable RoCE on the PF before we create the FDB under switchdev mode, so do that as well and revert if getting into error during the mode change later. Fixes: 9da34cd3 ('net/mlx5: Disable RoCE on the e-switch management [..]') Signed-off-by:
Or Gerlitz <ogerlitz@mellanox.com> Reviewed-by:
Hadar Hen Zion <hadarh@mellanox.com> Signed-off-by:
-
Ard Biesheuvel authored
[ Upstream commit f073bdc5 ] The VM_BUG_ON() check in move_freepages() checks whether the node id of a page matches the node id of its zone. However, it does this before having checked whether the struct page pointer refers to a valid struct page to begin with. This is guaranteed in most cases, but may not be the case if CONFIG_HOLES_IN_ZONE=y. So reorder the VM_BUG_ON() with the pfn_valid_within() check. Link: http://lkml.kernel.org/r/1481706707-6211-2-git-send-email-ard.biesheuvel@linaro.orgSigned-off-by:
Ard Biesheuvel <ard.biesheuvel@linaro.org> Acked-by:
Will Deacon <will.deacon@arm.com> Cc: Catalin Marinas <catalin.marinas@arm.com> Cc: Hanjun Guo <hanjun.guo@linaro.org> Cc: Yisheng Xie <xieyisheng1@huawei.com> Cc: Robert Richter <rrichter@cavium.com> Cc: James Morse <james.morse@arm.com> Signed-off-by:
-
Jamie Iles authored
[ Upstream commit 2d39b3cd ] Since commit 00cd5c37 ("ptrace: permit ptracing of /sbin/init") we can now trace init processes. init is initially protected with SIGNAL_UNKILLABLE which will prevent fatal signals such as SIGSTOP, but there are a number of paths during tracing where SIGNAL_UNKILLABLE can be implicitly cleared. This can result in init becoming stoppable/killable after tracing. For example, running: while true; do kill -STOP 1; done & strace -p 1 and then stopping strace and the kill loop will result in init being left in state TASK_STOPPED. Sending SIGCONT to init will resume it, but init will now respond to future SIGSTOP signals rather than ignoring them. Make sure that when setting SIGNAL_STOP_CONTINUED/SIGNAL_STOP_STOPPED that we don't clear SIGNAL_UNKILLABLE. Link: http://lkml.kernel.org/r/20170104122017.25047-1-jamie.iles@oracle.comSigned-off-by:
Jamie Iles <jamie.iles@oracle.com> Acked-by:
Oleg Nesterov <oleg@redhat.com> Cc: Alexander Viro <viro@zeniv.linux.org.uk> Cc: Ingo Molnar <mingo@redhat.com> Cc: Peter Zijlstra <peterz@infradead.org> Signed-off-by:
-
Sudip Mukherjee authored
[ Upstream commit da0510c4 ] The build of frv allmodconfig was failing with the errors like: /tmp/cc0JSPc3.s: Assembler messages: /tmp/cc0JSPc3.s:1839: Error: symbol `.LSLT0' is already defined /tmp/cc0JSPc3.s:1842: Error: symbol `.LASLTP0' is already defined /tmp/cc0JSPc3.s:1969: Error: symbol `.LELTP0' is already defined /tmp/cc0JSPc3.s:1970: Error: symbol `.LELT0' is already defined Commit 866ced95 ("kbuild: Support split debug info v4") introduced splitting the debug info and keeping that in a separate file. Somehow, the frv-linux gcc did not like that and I am guessing that instead of splitting it started copying. The first report about this is at: https://lists.01.org/pipermail/kbuild-all/2015-July/010527.html. I will try and see if this can work with frv and if still fails I will open a bug report with gcc. But meanwhile this is the easiest option to solve build failure of frv. Fixes: 866ced95 ("kbuild: Support split debug info v4") Link: http://lkml.kernel.org/r/1482062348-5352-1-git-send-email-sudipm.mukherjee@gmail.comSigned-off-by:
Sudip Mukherjee <sudip.mukherjee@codethink.co.uk> Reported-by:
Fengguang Wu <fengguang.wu@intel.com> Cc: Andi Kleen <ak@linux.intel.com> Cc: David Howells <dhowells@redhat.com> Signed-off-by:
-
Michal Hocko authored
[ Upstream commit bb1107f7 ] Andrey Konovalov has reported the following warning triggered by the syzkaller fuzzer. WARNING: CPU: 1 PID: 9935 at mm/page_alloc.c:3511 __alloc_pages_nodemask+0x159c/0x1e20 Kernel panic - not syncing: panic_on_warn set ... CPU: 1 PID: 9935 Comm: syz-executor0 Not tainted 4.9.0-rc7+ #34 Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS Bochs 01/01/2011 Call Trace: __alloc_pages_slowpath mm/page_alloc.c:3511 __alloc_pages_nodemask+0x159c/0x1e20 mm/page_alloc.c:3781 alloc_pages_current+0x1c7/0x6b0 mm/mempolicy.c:2072 alloc_pages include/linux/gfp.h:469 kmalloc_order+0x1f/0x70 mm/slab_common.c:1015 kmalloc_order_trace+0x1f/0x160 mm/slab_common.c:1026 kmalloc_large include/linux/slab.h:422 __kmalloc+0x210/0x2d0 mm/slub.c:3723 kmalloc include/linux/slab.h:495 ep_write_iter+0x167/0xb50 drivers/usb/gadget/legacy/inode.c:664 new_sync_write fs/read_write.c:499 __vfs_write+0x483/0x760 fs/read_write.c:512 vfs_write+0x170/0x4e0 fs/read_write.c:560 SYSC_write fs/read_write.c:607 SyS_write+0xfb/0x230 fs/read_write.c:599 entry_SYSCALL_64_fastpath+0x1f/0xc2 The issue is caused by a lack of size check for the request size in ep_write_iter which should be fixed. It, however, points to another problem, that SLUB defines KMALLOC_MAX_SIZE too large because the its KMALLOC_SHIFT_MAX is (MAX_ORDER + PAGE_SHIFT) which means that the resulting page allocator request might be MAX_ORDER which is too large (see __alloc_pages_slowpath). The same applies to the SLOB allocator which allows even larger sizes. Make sure that they are capped properly and never request more than MAX_ORDER order. Link: http://lkml.kernel.org/r/20161220130659.16461-2-mhocko@kernel.orgSigned-off-by:
Michal Hocko <mhocko@suse.com> Reported-by:
Christoph Lameter <cl@linux.com> Cc: Alexei Starovoitov <ast@kernel.org> Signed-off-by:
-
Rabin Vincent authored
[ Upstream commit 270c8cf1 ] ARM has a few system calls (most notably mmap) for which the names of the functions which are referenced in the syscall table do not match the names of the syscall tracepoints. As a consequence of this, these tracepoints are not made available. Implement arch_syscall_match_sym_name to fix this and allow tracing even these system calls. Signed-off-by:
Rabin Vincent <rabinv@axis.com> Signed-off-by:
Russell King <rmk+kernel@arm.linux.org.uk> Signed-off-by:
-
Omar Sandoval authored
[ Upstream commit 6bf6b0aa ] If blk_mq_init_queue() returns an error, it gets assigned to vblk->disk->queue. Then, when we call put_disk(), we end up calling blk_put_queue() with the ERR_PTR, causing a bad dereference. Fix it by only assigning to vblk->disk->queue on success. Signed-off-by:
Omar Sandoval <osandov@fb.com> Reviewed-by:
Jeff Moyer <jmoyer@redhat.com> Signed-off-by:
Jens Axboe <axboe@fb.com> Signed-off-by:
-
Jeff Moyer authored
[ Upstream commit 25b4acfc ] Additionally, don't assign directly to disk->queue, otherwise blk_put_queue (called via put_disk) will choke (panic) on the errno stored there. Bug found by code inspection after Omar found a similar issue in virtio_blk. Compile-tested only. Signed-off-by:
Josef Bacik <jbacik@fb.com> Signed-off-by:
-
Steve Wise authored
[ Upstream commit 3bcf96e0 ] Function rx_data(), which handles ingress CPL_RX_DATA messages, was always sending an RX_DATA_ACK with the goal of updating the credits. However, if the RDMA connection is moved out of FPDU mode abruptly, then it is possible for iw_cxgb4 to process queued RX_DATA CPLs after HW has aborted the connection. These CPLs should not trigger RX_DATA_ACKS. If they do, HW can see a READ after DELETE of the DB_LE hash entry for the tid and post a LE_DB HashTblMemCrcError. Signed-off-by:
Steve Wise <swise@opengridcomputing.com> Signed-off-by:
-
