- 29 Feb, 2008 40 commits
-
-
Luis R. Rodriguez authored
Author: Adrian Bunk <bunk@kernel.org> This patch fixes a negative array index spotted by the Coverity checker. Changes-licensed-under: ISC Acked-by:
Nick Kossifidis <mickflemm@gmail.com> Signed-off-by:
Adrian Bunk <bunk@kernel.org> Signed-off-by:
Luis R. Rodriguez <mcgrof@winlab.rutgers.edu> Signed-off-by:
John W. Linville <linville@tuxdriver.com>
-
Luis R. Rodriguez authored
Hardware encryption doesn't work yet so lets use software encryption for now. Changes-licensed-under: 3-Clause-BSD Signed-off-by:
-
Luis R. Rodriguez authored
This patch finishes the port and enables debug as an build option. This was tested on: Atheros AR5213A chip found (MAC: 0x59, PHY: 0x43) RF5112A multiband radio found (0x36) Note: For 2 GHz band on the above card I noticed we get negative channel numbers. Will look into this unless someone beats me to it. Example out put when loading using: sudo modprobe ath5k debug=0x00000400 Band 2 GHz: channels 26, rates 12 channels: 1 2412 00c0 0000 2 2417 00c0 0000 3 2422 00c0 0000 4 2427 00c0 0000 5 2432 00c0 0000 6 2437 00c0 0000 7 2442 00c0 0000 8 2447 00c0 0000 9 2452 00c0 0000 10 2457 00c0 0000 11 2462 00c0 0000 12 2467 00c0 0000 13 2472 00c0 0000 14 2484 00c0 0000 -498 2512 00c0 0000 -494 2532 00c0 0000 -490 2552 00c0 0000 -486 2572 00c0 0000 -482 2592 00c0 0000 -478 2612 00c0 0000 -474 2632 00c0 0000 -470 2652 00c0 0000 -466 2672 00c0 0000 -462 2692 00c0 0000 -458 2712 00c0 0000 -454 2732 00c0 0000 Band 5 GHz: channels 194, rates 8 channels: 27 5135 0140 0000 28 5140 0140 0000 [... etc ] 219 6095 0140 0000 220 6100 0140 0000 rates: 60 000b 0000 0000 90 000f 0000 0000 120 000a 0000 0000 180 000e 0000 0000 240 0009 0000 0000 360 000d 0000 0000 480 0008 0000 0000 540 000c 0000 0000 Changes to base.c, base.h Changes-licensed-under: 3-Clause-BSD Changes to debug.c, debug.h Changes-licensed-under: GPL Signed-off-by: -
Luis R. Rodriguez authored
Apologoes, this is a re-post of patch-04, forgot to git-add our Kconfig... New series (only 2 patches needed fixing, which I am reposting) can be found here: http://kernel.org/pub/linux/kernel/people/mcgrof/patches/ath5k/2008-02-04.v2/ Use our own Kconfig file, we'll be expanding this shortly. Signed-off-by:
-
Luis R. Rodriguez authored
ath5k_copy_channels() wasn't setting the channel's band so all driver channels had a 2GHz band set. Lets set this. Changes-licensed-under: 3-Clause-BSD Signed-off-by:
-
Luis R. Rodriguez authored
Cleanup after API changes patch (checkpatch.pl stuff) and on ath5k_hw_channel() make use of the existing ath5k_channel_ok() instead of re-implementing the checks again. This was necessary to make the code cleaner and fit the 80-chars wide limit so sending it within the same patch. Finally make a note that we *may* eventually move cap_range stuff to struct wiphy (band frequency range capabilities). This information can later be exported to userspace, for example, and giving it access to mac80211 and drivers in general can come in handy. Changes to initvals.c, phy.c Changes-licensed-under: ISC Changes to ath5k.h, base.c Changes-licensed-under: 3-Clause-BSD Signed-off-by:
-
Luis R. Rodriguez authored
Author: Nick Kossifidis <mickflemm@gmail.com> Tested on 5211, 5213+5112, 5213A+2112A and it wors fine. Also i figured out a way to process rate vallue found on status descriptors, it's still buggy but we are getting closer (i think it improved stability a little). Changes to hw.c, initvals.c, phy.c Changes-licensed-under: ISC Changes to ath5k.h, base.c, base.h Changes-licensed-under: 3-Clause-BSD Acked-by:
Jiri Slaby <jirislaby@gmail.com> Signed-off-by:
-
Ivo van Doorn authored
When the driver registers a IEEE80211_BAND_2GHZ band, it can either be 802.11b or 802.11g. But when 802.11b rates are registered "want" will be 3 (since 4 rates are being registered, and each of those 4 rates will decrease "want"). Since this is a correct situation, there is no need to trigger a WARN_ON() for this. Signed-off-by:
Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by:
-
Mohamed Abbas authored
rate_idx is derived from plcp information Signed-off-by:
Mohamed Abbas <mohamed.abbas@intel.com> Signed-off-by:
Reinette Chatre <reinette.chatre@intel.com> Signed-off-by:
-
Mohamed Abbas authored
hw_value is being used uninitialized. fix it. Signed-off-by:
-
Johannes Berg authored
In the rate API patch I accidentally reverted the test for ERP rates, this fixes it. All rates except 1, 2, 5.5 and 11 MBit are ERP rates, not those. Signed-off-by:
Johannes Berg <johannes@sipsolutions.net> Signed-off-by:
-
Stefano Brivio authored
Merge rate_control_pid_shift_adjust() to rate_control_pid_adjust_rate() in order to make the learning algorithm aware of constraints on rates. Also add some comments and rename variables. This fixes a bug which prevented 802.11b/g non-AP STAs from working with 802.11b only AP STAs. Signed-off-by:
Stefano Brivio <stefano.brivio@polimi.it> Signed-off-by:
-
Johannes Berg authored
This patch removes the 802.1X port acess control enable flag since it is not required. Instead, set the authorized flag for each station that we normally communicate with (WDS peers, IBSS peers and APs we're associated to) and require hostapd to set the authorized flag for all stations when port control is not enabled. Also, since I was working in that area, this documents station flags and removes the unused "permanent" one. Signed-off-by:
-
Johannes Berg authored
When checking for the next band to advance to, there was an off-by-one error that could lead to an access to an invalid array index. Additionally, the later check for scan_band >= IEEE80211_NUM_BANDS is not required since that will never be true. This also improves the comments related to that code. Signed-off-by:
-
Johannes Berg authored
This makes nl80211 export the hardware bitrate/channel capabilities as registered in a wiphy. Signed-off-by:
-
Johannes Berg authored
This patch creates new cfg80211 wiphy API for channel and bitrate registration and converts mac80211 and drivers to the new API. The old mac80211 API is completely ripped out. All drivers (except ath5k) are updated to the new API, in many cases I expect that optimisations can be done. Along with the regulatory code I've also ripped out the IEEE80211_HW_DEFAULT_REG_DOMAIN_CONFIGURED flag, I believe it to be unnecessary if the hardware simply gives us whatever channels it wants to support and we then enable/disable them as required, which is pretty much required for travelling. Additionally, the patch adds proper "basic" rate handling for STA mode interface, AP mode interface will have to have new API added to allow userspace to set the basic rate set, currently it'll be empty... However, the basic rate handling will need to be moved to the BSS conf stuff. I do expect there to be bugs in this, especially wrt. transmit power handling where I'm basically clueless about how it should work. Signed-off-by:
-
Ivo van Doorn authored
When Q_INDEX is increased, the queue->length should be increased, only when Q_INDEX_DONE is increased should queue_length be descreased. Signed-off-by:
-
Ivo van Doorn authored
As Johannes Berg indicated the BEACON and AFTER_BEACON queue indeces in mac80211 should be removed because they are too hardware specific. This patch adds the queue index defines into rt2x00queue.h and removes the dependency of the defines inside mac80211.h. Also move rt2x00pci_beacon_update() into rt2400pci and rt2500pci individually since it is no longer a generic function since rt61 and rt2800 no longer use that. Signed-off-by:
-
Ivo van Doorn authored
The QID_MGMT is assigned to the beacon and atim queue during initialization. This means we don't need a seperate check in write_tx_desc().. Signed-off-by:
-
Ivo van Doorn authored
rt73usb doesn't have a 5th queue, correctly initialize hw->queues rt61pci had a 5th queue but was removed recently, correctly initialize hw->queues and remove the last remnants. Signed-off-by:
-
Ivo van Doorn authored
Rework the interface handling. Delete the interface structure and replace it with a per-interface structure. This changes the way rt2x00 handles the active interface drastically. Copy ieee80211_bss_conf to the this rt2x00_intf structure during the bss_info_changed() callback function. This will allow us to reference it later, and removes the requirement for the device flag SHORT_PREAMBLE flag which is interface specific. Drivers receive the option to give the maximum number of virtual interfaces the device can handle. Virtual interface support: rt2400pci: 1 sta or 1 ap, * monitor interfaces rt2500pci: 1 sta or 1 ap, * monitor interfaces rt2500usb: 1 sta or 1 ap, * monitor interfaces rt61pci: 1 sta or 4 ap, * monitor interfaces rt73usb: 1 sta or 4 ap, * monitor interfaces At the moment none of the drivers support AP and STA interfaces simultaneously, this is a hardware limitation so future support will be very unlikely. Each interface structure receives its dedicated beacon entry, with this we can easily work with beaconing while multiple master mode interfaces are currently active. The configuration handlers for the MAC, BSSID and type are often called together since they all belong to the interface configuration. Merge the 3 configuration calls and cleanup the API between rt2x00lib and the drivers. While we are cleaning up the interface configuration anyway, we might as well clean up the configuration handler as well. Signed-off-by:
-
Ivo van Doorn authored
The driver should select what CRC algorithm is required when performing a checksum on the firmware. rt61pci & rt73usb require crc-itu-t rt2800pci & rt2800usb require crc-ccitt Legacy 2800pci/usb driver uses crc-itu-t + bit order reversion, but that is just inefficient especially since the end result is the same as a different algorithm which is also available as library. ;) Signed-off-by:
-
Ivo van Doorn authored
This will enable the creation of master mode and adhoc interfaces again. This does not mean the issues surrounding beaconing have been resolved, but this will make testing easier and perhaps we can discover which cards are actually working and which ones not. Signed-off-by:
-
Ivo van Doorn authored
Check if the aifs, cw_min and cw_max are above 0 when determining if the default should be used. Tor aifs a negative number is used to determine if the default should be used or not. Signed-off-by:
-
Adam Baker authored
The space allocated in the skb for a descriptor is only 24 bytes when setting up beacons in rt61 so make sure we don't write to the descriptor words beyond that and corrupt the beacon packet. Signed-off-by:
Adam Baker <linux@baker-net.org.uk> Signed-off-by:
-
Ivo van Doorn authored
This introduces a big queue handling overhaul, this also renames "ring" to "queues". Move queue handling into rt2x00queue.c and the matching header, use Kerneldoc to improve rt2x00 library documentation. Access to the queues is now protected under a spinlock, this to prevent race conditions which could corrupt the indexing system of the queue. Each queue entry allocates x bytes for driver/device specific data, this cleans up the queue structure significantly and improves code readability. rt2500usb no longer needs 2 entries in the beacon queue to correctly send out the guardian byte. This is now handled in the entry specific structure. rt61 and rt73 now use the correct descriptor size for beacon frames, since this data is written into the registers not the entire TXD descriptor was used but instead of a subset of it named TXINFO. Finally this also fixes numerous other bugs related to incorrect beacon handling or beacon related code. Signed-off-by:
-
Ivo van Doorn authored
Signed-off-by:
-
Roel Kluin authored
'!' has a higher priority than '&': bitanding has no effect. Signed-off-by:
Roel Kluin <12o3l@tiscali.nl> Signed-off-by:
-
Johannes Berg authored
These handlers do not really return a status and the compiler can do a much better job when they're simply static functions that it can inline if appropriate. Also makes the code shorter. Signed-off-by:
-
Tomas Winkler authored
This patch removes 'IWL4965_HT: depends on n' from iwlwifi's Kconfig 1. 11n is functional so no need to make it invisible in the configuration 2. Latest Johannes patch 'cfg80211 API for channels/bitrates, mac80211 and driver conversion' broke compilation because this config option was invisible - patch fixing it will be provided later Signed-off-by:
Tomas Winkler <tomas.winkler@intel.com> Signed-off-by:
-
Ron Rindjunsky authored
This patch gives a heuristic for activation of the A-MPDU Tx. As the rate scaling is rate aware, it now also measures estimated load, and sends A-MPDU activation after a threshold has been met. Signed-off-by:
Ron Rindjunsky <ron.rindjunsky@intel.com> Signed-off-by:
-
Ron Rindjunsky authored
This patch uses the changes in ieee80211_tx_status to pass Block Ack data to rate scaling module, and uses this data in rate scaling calculations Signed-off-by:
-
Ron Rindjunsky authored
This patch alters the current iwlwifi behavior to fit the flows introduced by the mac80211, mainly queues handling and start/stop call backs flows Signed-off-by:
-
Ron Rindjunsky authored
This patch alters the current API in order to fit the new API mac80211 gives for A-MPDU Tx Signed-off-by:
-
Ron Rindjunsky authored
This patch adds the ability to handle delBA from recipient to initiator during an A-MPDU session Signed-off-by:
-
Ron Rindjunsky authored
This patch adds fields to ieee80211_tx_status in order to allow block ack information exchange between low-level driver,mac80211 and rate scaling module. Signed-off-by:
-
Ron Rindjunsky authored
This patch adds A-MPDU status report per STA to the debugfs. The option to de/activate A-MPDU through debugfs is also present. Signed-off-by:
-
Ron Rindjunsky authored
This patch initialize A-MPDU MLME data for Tx sessions. Signed-off-by:
-
Ron Rindjunsky authored
This patch allows qdisc support in A-MPDU Tx. a method to handle QoS <-> TID switches is present in this patch. Signed-off-by:
-
Ron Rindjunsky authored
This patch adds the following abilities to mac80211: - start A-MPDU Tx session - stop A-MPDU Tx session - call backs to start/stop A-MPDU Tx session - sending addBA request - processing addBA response Signed-off-by:
-
