- 05 Jun, 2012 40 commits
-
-
Victor Goldenshtein authored
The beacon early termination is not relevant for high basic rates, which doesn't contribute anything to the PS and only adds unnecessary FW work. Enable BET only if the basic rate is less than 9 Mbps. Signed-off-by:
Ziv Riesel <zivriesel@ti.com> Signed-off-by:
Victor Goldenshtein <victorg@ti.com> Signed-off-by:
Igal Chernobelsky <igalc@ti.com> Signed-off-by:
Luciano Coelho <coelho@ti.com>
-
Victor Goldenshtein authored
Wrong fm_coex parameters were set during wl18xx init phase, fix it. Signed-off-by:
-
Victor Goldenshtein authored
Wrong fm_coex parameters were set during wl12xx init phase, fix it. Signed-off-by:
-
Arik Nemtsov authored
This BUG_ON also ignored the INTENDED_FW_RECOVERY flag. This would result in a BUG() when using the bug_on_recovery module parameter during multi-role. Signed-off-by:
Arik Nemtsov <arik@wizery.com> Signed-off-by:
-
Eliad Peller authored
In some cases, the ROC_COMPLETE event might exceed the current timeout (750 msec). Increase it to 1 sec. Signed-off-by:
Eliad Peller <eliad@wizery.com> Signed-off-by:
-
Eliad Peller authored
On CHANGE_CHANNEL indication, we should flush all the queued tx frames, so they will be sent on the correct (current) channel. Signed-off-by:
-
Yoni Divinsky authored
In the enum conf_tx_ac CONF_TX_AC_ANY_TID should be 0xff to match the firmware's implementation. Signed-off-by:
Yoni Divinsky <yoni.divinsky@ti.com> Signed-off-by:
-
Yoni Divinsky authored
The polarity should be set before the firmware is loaded since the firmware touches the same register. Access of the firmware and driver to the same register will cause a collision since there is no exclusion scheme. Signed-off-by:
-
Yoni Divinsky authored
In ieee80211.h the uapsd bit mask is defined such that VO=BIT(0), VI=BIT(1), BK=BIT(2), BE=BIT(3). The firmware uses the indexing as defined in the ieee80211 spec, meaning that VO=3, VI=2, BK=1, BE=0. In AP mode when adding peer wlcore needs to convert the indexing accordingly. Signed-off-by:
-
Eliad Peller authored
Save the ht_cap IE per-band, so we can configure different params to BG and A bands (we currently don't support MIMO on A band) [Small fix for rx_highest - Arik] Signed-off-by:
-
Arik Nemtsov authored
Add a dependency on mac80211 in Kconfig, and also replace some spaces with tabs. Reported-by:
Arend van Spriel <arend@broadcom.com> Signed-off-by:
-
Assaf Azulay authored
With the new FW (sigle role X.3.8.0.108, multi role X.5.4.0.21) we are supporting 3 RX BA sessions, this change is to support this new ability. Signed-off-by:
Assaf Azulay <assaf@ti.com> Signed-off-by:
-
Igal Chernobelsky authored
Modify default parameters to reduce firmware BSS lose probability in congested environment. [Applied to 18xx configuration as well - Arik] Signed-off-by:
-
Eliad Peller authored
Make sure the deauth bcast gets sent [Make sure we are AP as well before the flush - Arik] Signed-off-by:
-
Eliad Peller authored
Multicast management frames (e.g. global deauth) should be sent out on the bcast link, rather than the global, which should be used only for pre-added stations (e.g. for auth/assoc resp). Signed-off-by:
Eyal Shapira <eyal@wizery.com> Signed-off-by:
-
Arik Nemtsov authored
We can't use cancel_delayed_work_sync() from functions that take the wl->mutex, since connection_loss_work also takes the mutex. This might result in a deadlock. Restructure the code so the work is synchronously canceled before taking the mutex. Avoid a bug where we would indefinitely delay the connection loss indication by re-queuing the connection loss work on consecutive beacon loss events. Cc: bartosz.markowski <bartosz.markowski@tieto.com> Signed-off-by:
-
Arik Nemtsov authored
In patch d7b63b9f we have raised the dynamic PS timeout to 200ms to improve user experience. Re-apply the change, since it was reverted in the wlcore split. Signed-off-by:
-
Eliad Peller authored
The dynamic PS timeout is meaningless in forced PS mode. Signed-off-by:
-
Arik Nemtsov authored
The "static" modifier was mistakenly forgotten for some functions. Signed-off-by:
-
Luciano Coelho authored
Commit 4afc37 (wlcore: reorder identify_chip and get_hw_info) broke support for wl127x chips. When we moved the identify_chip operation to an earlier stage (ie. to the probe function), we broke wl127x support because during HW init we would set the WLCORE_QUIRK_TX_BLOCKSIZE_ALIGN. To avoid this, set this quirk in the identify_chip operations and only force it to be unset if the bus module doesn't support it. We were doing the opposite and setting the flag if the bus module supports it. Signed-off-by: -
Assaf Azulay authored
as tcp check sum is going to be removed from firmware, and as there is a problem with getting dns in security when checksum is enabled, it was decided to disable it by default. for none security modes it can be enabled by module paramenter. Signed-off-by:
-
Luciano Coelho authored
Some of the structures were updated, other structures had a few missing values and a few new ones were added. Change the driver structs accordingly. Signed-off-by:
-
Luciano Coelho authored
Now the firmware can support TX block ack sessions with 64 frames. Signed-off-by:
-
Luciano Coelho authored
With 4 pages (16Kb), we can't fit 10 frames in the aggregation buffer during iperf. This is the optimal for the firmware. Thus, increase the buffer size by one page. Signed-off-by:
-
Luciano Coelho authored
Instead of adding more files from the lower drivers into the same directory in debugfs as wlcore, we now add a subdirectory for the lower driver. This makes things a bit easier, because we can quickly see where the debugfs entry is implemented and what is specific to the lower driver. Signed-off-by:
-
Luciano Coelho authored
Yet another temporary module parameter requested by the firmware team. This will be replaced by the conf binary. Signed-off-by:
-
Luciano Coelho authored
We use hardcoded values for the different board types. In some cases we may need to override the defaults, so export the values as module params. If not defined, the defaults for the specified board type will be used. Signed-off-by:
-
Luciano Coelho authored
With more recent PHY firmware versions (>8.1.0.0.116), we need to use the correct value for the pwr_limit_reference_11_abg parameter when setting the mac_and_phy options. For now we use a hardcoded 0xc8 as the value. This will be moved to the configuration binary when it gets implemented. Signed-off-by:
-
Luciano Coelho authored
In some cases it may be useful to force narrow-band SISO channels. Add a new value to the ht_mode module parameter to force the device to operate in SISO 20MHz. Signed-off-by:
-
Luciano Coelho authored
We were setting all the rates bits when starting the AP role. Instead of doing this, we should set only the rates we really support (eg. MIMO rates or wide-channel rates). This commit changes that so that we always use the default rates (basic rates + MCS0-7) and add the values returned by the ap_get_mimo_wide_rate_mask operation. Signed-off-by:
-
Luciano Coelho authored
If the wl18xx module is loaded with ht_mode=wide (the default), we shouldn't use MIMO rates when the channel type is not HT40. Fix this by checking the ht_mode before deciding which rates to used. Additionally, set the ht_mode parameter explicitly to "wide" as the default. Signed-off-by:
-
Luciano Coelho authored
In some cases it may be useful for debugging to check what is the status of the interrupt register when a hardware recovery happens. Print the contents of REG_INTERRUPT_NO_CLEAR (aka. HINT_STS_RAW) when recovery starts. Signed-off-by:
-
Luciano Coelho authored
The wl18xx firmware writes the PHY firmware version in the static data. Add an operation to parse the static data and print the PHY firmware version when booting. Signed-off-by:
-
Luciano Coelho authored
The wl18xx firmware has more information in the static_data than wl12xx. To be able to parse that in an abstracted way, this patch adds a priv area to the static data struct and an operation that allows the lower driver to parse it if necessary. Signed-off-by:
-
Luciano Coelho authored
Implement the operations that are necessary to fetch the wl18xx-specific FW statistics and export them in debugfs. Signed-off-by:
-
Luciano Coelho authored
Implement the operations that are necessary to fetch the wl12xx-specific FW statistics. Re-add some of the code removed from wlcore. Signed-off-by:
-
Luciano Coelho authored
Add a macro to make it easy to print arrays from the FW statistics array in debugfs. At the same time, increase the buffer size so arrays fit more easily. Signed-off-by:
-
Luciano Coelho authored
The FW statistics differ from hardware to hardware. This commit prepares for hardware-specific implementation of the FW statistics debugfs entries. Signed-off-by:
-
Luciano Coelho authored
Sometimes we get a BSS_CHANGED_BEACON_ENABLED event before the basic rates have been properly set. To avoid problems with the firmware not expecting to receive frames at rates that are not set during CMD_START_ROLE, we now start with all basic rates by default. Signed-off-by:
-
Luciano Coelho authored
When the data rates change, we get BSS_CHANGED_BASIC_RATES. At this point, we should update all the templates to match the new rates. We were changing some of the templates, but the beacon and the probe response templates were missing. [Remove redundant min_rate variable - Arik] Signed-off-by:
-
