This is the only board that presently supports this rtc, so make sure it
is enabled by default to get some build coverage.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

There were a few stray unused variables left over, kill them off.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

As an excellent indicator of how much testing the DSP code gets, a couple
of rather glaring bugs in the DSP save/restore paths were found:

- In the DSP restore case a0 needs to be popped off before a0g,
  or the value of a0g is clobbered by the MSB of a0 in the case
  of sign extension.

- Beyond that, the save and restore orders were out of sync,
  so this fixes that up as well. At the same time, we switch over
  to using movs.l for both the save and restore of the general DSP
  registers as opposed to using sts.l (which was initially put in
  place to work around a bug in ancient binutils versions which
  the kernel no longer supports).
Reported-by: Chee Soon Yip <yip.cheesoon@renesas.com>
Cc: Chu Lih Kwek <kwek.chulih@renesas.com>,
Cc: General Lai <general.lai@renesas.com>,
Cc: Robert Cozens <Robert.Cozens@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

Signed-off-by: Michael Trimarchi <trimarchimichael@yahoo.it>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

- simplifies irq set freq
- ioctl() was duplicating functionalities of rtc-dev core
- corrected initialization sequence
- use platform_driver_probe
Signed-off-by: Alessandro Zummo <a.zummo@towertech.it>
Cc: Angelo Castello <angelo.castello@st.com>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Kay Sievers <kay.sievers@vrfy.org>
Cc: Jamie Lenehan <lenehan@twibble.org>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

- removed spinlock protection, it's handled by the rtc class
- use platform_driver_probe
- return appropriate code for rtc_read_time
- style issues
Signed-off-by: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

-tip can't be bothered keeping interfaces stable long enough for anyone
to use them without having their builds broken without notification, so
just ifdef around the problematic symbols until the new interfaces become
available upstream.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

Add USB gadget support for port CN26 on the Solution Engine 7724
board. The r8a66597-udc driver is hooked up as a platform device
and some registers are configured to enable the USB in gadget mode.
The hardware driving the USB port is the on-chip USB1 block in
the sh7724 processor configured as USB gadget controller.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

Add USB gadget support for port YC301 on the KFR2R09 board.

The r8a66597-udc driver is hooked up as a platform device,
clocks are enabled via I2C and some registers are configured
to enable the USB in gadget mode. The hardware driving the
USB port is the on-chip USB0 block in the sh7724 processor
configured as USB gadget controller.

This board is using external hardware to detect USB hotplug
events and allows the processor to dynamically start and stop
clocks. This well thought out hardware feature is unused at
this point and plug and play is unfortunately unsupported.
To properly support all hardware features the USB gadget
stack may need some adjustment.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

This patch improves the disable_controller() function in the
r8a66597-udc driver to disable all interrupts and also clear
status flags. With this patch in place the driver survives
kexec.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

This patch updates the r8a66597-udc buffer management code.

Use fixed buffers for bulk and isochronous pipes, also make
sure to handle the isochronous-as-bulk case. With fixed buffers
there is no need to keep track of used buffers with bi_bufnum.

Also, this fixes a potential buffer offset problem where the
base offset incorrectly varies with the number of pipes used.

The m66592 driver recently got fixed in a similar way.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

Add support for the clock framework to the r8a66597 gadget driver.
This is needed to control the clock driving the USB block.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

While in-tree support for the R8A66597 host side has been supported for
some time, the peripheral side has so far been unsupported. This adds a
new USB gadget driver which bridges the gap and finally wires up the
peripheral side as well.
Signed-off-by: Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
Tested-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

Signed-off-by: Paul Mundt <lethal@linux-sh.org>

This adds preliminary support for the EcoVec board.
Signed-off-by: Kuninori Morimoto <morimoto.kuninori@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

This patch also update help comment
Signed-off-by: Kuninori Morimoto <morimoto.kuninori@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

Signed-off-by: Kuninori Morimoto <morimoto.kuninori@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

While most platforms implement LED banks in sets of 8/16/32, some use
different configurations. This adds a LED mask to the heartbeat platform
data to allow platforms to constrain the bitmap, which is otherwise
derived from the register size.
Signed-off-by: Kuninori Morimoto <morimoto.kuninori@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

This patch updates the FRQCRA.IFC divisor values for SH7724. Despite
not being initially documented, the / 3 mode is also support for the IFC
division.
Signed-off-by: Kuninori Morimoto <morimoto.kuninori@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

FLLFRQ setting is needed to use correct PLL clock for kfr2409.
Signed-off-by: Kuninori Morimoto <morimoto.kuninori@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

save_regs contains an SR modification without an irqflags annotation,
which resulted in a missing TRACE_IRQS_OFF in the interrupt exception
path on SH-3/SH4.

I've also moved the TRACE_IRQS_OFF/ON annotation when returning from the
interrupt to just before we call __restore_all. This seems like the most
logical place to put this because the annotation is for when we restore
the SR register so we should delay the annotation until as last as
possible.

We were also missing a TRACE_IRQS_OFF in resume_kernel when
CONFIG_PREEMPT is enabled.

The end result is that this fixes up the lockdep engine debugging support
with CONFIG_PREEMPT enabled on all SH-3/4 parts.
Signed-off-by: Matt Fleming <matt@console-pimps.org>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

This patch adds "SuperH Mobile Standby Mode [SF]" to the list
of cpuidle sleep modes. If the software latency requirements
from cpuidle are met together with fulfilled hardware
requirements then deep sleep modes can be entered.

Tested on sh7722 and sh7724 with "Sleep Mode", "Sleep Mode + SF"
and "Software Standby Mode + SF" together with a multimedia
work load and flood ping without packet drop.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

This patch updates the exception handling in the sleep code
for SuperH Mobile. With the patch applied the sleep code
always rewrites the VBR and resumes from the exception vector,
re-initializes hardware and jumps straight to the original
interrupt vector.

Tested on sh7722 and sh7724 with "Sleep Mode", "Sleep Mode + SF"
and "Software Standby Mode + SF" with CONFIG_SUSPEND.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

Also, remove the "fix" to DW_CFA_def_cfa_register where we reset the
frame's cfa_offset to 0. This action is incorrect when handling
DW_CFA_def_cfa_register as the DWARF spec specifically states that the
previous contents of cfa_offset should be used with the new
register. The reason that I thought cfa_offset should be reset to 0 was
because it was being assigned a bogus value prior to executing the
DW_CFA_def_cfa_register op. It turns out that the bogus cfa_offset value
came from interpreting .cfi_escape pseudo-ops (those used by the GNU
extensions) as CFA_DW_def_cfa ops.
Signed-off-by: Matt Fleming <matt@console-pimps.org>

The previous hack for calculating the return address for the first frame
we unwind (dwarf_unwinder_dump) didn't always work. The problem was that
it assumed once it read the rule for calculating the return address,
there would be no new rules for calculating it. This isn't true because
the way in which the CFA is calculated can change as you progress
through a function and the return address is figured out using the
CFA. Therefore, the way to calculate the return address can change.

So, instead of using some offset from the beginning of
dwarf_unwind_stack which is just a flakey approach, and instead of
executing instructions from the FDE until the return address is setup,
we now figure out the pc in dwarf_unwind_stack() just before we call
dwarf_cfa_execute_insns().
Signed-off-by: Matt Fleming <matt@console-pimps.org>

This uses the BITS export as per x86 in order to allow the same Makefile
to be used.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

This patch updates the SuperH Mobile sleep assembly code with
support for DBSC memory controller found in the sh7724 processor.

Without this fix the memory hooked up to the sh7724 processor
will never enter self-refresh mode before suspending to ram. The
effect of this is that the memory contents most likeley will be
lost upon resume which may or may not be what you want.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

This patch updates the Solution Engine 7724 board code to use
in-SoC KEYSC resources for the keyboard platform device. Using
the in-SoC key scan controller fixes a crash-during-resume issue.

Without this patch the KEYSC hardware block located in the board
specific FPGA is used together with an external IRQ which is
routed through the FPGA and handled by some board specific demux
code. This board specific FPGA interrupt code does not implement
desc->set_wake() so the enable_irq_wake() call in the sh_keysc
driver will fail at suspend-to-ram time and the disable_irq_wake()
will bomb out when resuming.

Changing the platform data to use the in-SoC KEYSC hardware makes
the se7724 board support code less special which is a good thing.
Also, the board specific KEYSC pin setup code selects in-SoC pin
functions already which makes the current FPGA platform device data
look like a typo.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

This patch updates the SuperH CMT driver with suspend and resume
callbacks for the suspend-to-ram case. This patch stops the CMT
channel at suspend time to avoid unwanted wake up events.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

This patch updates the SuperH Mobile LCDC driver to skip
over disabled channels. Without this patch suspend-to-ram
operation will crash if deferred io is enabled.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

The way that the CFA is calculated can change as we progress through a
function. If we see a DW_CFA_def_cfa_register op we need to reset the
frame's cfa_offset value which may have been previously setup.
Signed-off-by: Matt Fleming <matt@console-pimps.org>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

This implements EXPMASK initialization code for SH-4A parts, where it is
possible to disable compat features that will go away in newer cores.
Presently this includes disabling support for non-nop instructions in the
rte delay slot, as well as a sleep instruction being placed in a delay
slot (neither of which the kernel does any longer). As a result of this,
any future offenders will have illegal slot exceptions generated for
them.

Associative writes for the memory-mapped cache array are still left
enabled, until such a point that special cache operations for SH-4A are
provided to move off of the current (and rather dated) SH-4 versions.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

Future SH parts do not support any instruction but a nop in the rte delay
slot, so make the change for all offending parts. SH-5 is excluded from
this, and already has its own set of restrictions with regards to rte
delay slot handling.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

This inserts a ULONG_MAX entry at the end of the valid entries in the
stack trace buffer so the default code doesn't need to scan to the end of
available slots. This also makes the trace buffer termination behaviour
consistent with the other architectures.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

This flags the default unwinder as reliable, as it tends to be reliable
enough for the purposes of the stacktrace buffer. We leave the unreliable
cases for the unwind methods that we know to be completely broken.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

This adopts the reliability checks from the x86 stacktrace code so known
bad addresses are not recorded in the stack trace buffer.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

save_stack_trace_tsk() and friends can be called from atomic context (as
triggered by latencytop), and subsequently hit two problematic allocation
points that were using GFP_KERNEL (these were dwarf_unwind_stack() and
dwarf_frame_alloc_regs()). Convert these over to GFP_ATOMIC and get
latencytop working with the DWARF unwinder.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>