- 16 Mar, 2017 40 commits
-
-
Augusto Mecking Caringi authored
commit c8a6a09c upstream. In ca91cx42_slave_get function, the value pointed by vme_base pointer is set through: *vme_base = ioread32(bridge->base + CA91CX42_VSI_BS[i]); So it must be dereferenced to be used in calculation of pci_base: *pci_base = (dma_addr_t)*vme_base + pci_offset; This bug was caught thanks to the following gcc warning: drivers/vme/bridges/vme_ca91cx42.c: In function ‘ca91cx42_slave_get’: drivers/vme/bridges/vme_ca91cx42.c:467:14: warning: cast from pointer to integer of different size [-Wpointer-to-int-cast] *pci_base = (dma_addr_t)vme_base + pci_offset; Signed-off-by:
Augusto Mecking Caringi <augustocaringi@gmail.com> Acked-By:
Martyn Welch <martyn@welchs.me.uk> Signed-off-by:
Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by:
Ben Hutchings <ben@decadent.org.uk>
-
Akinobu Mita authored
commit 802c0388 upstream. The sysrq input handler should be attached to the input device which has a left alt key. On 32-bit kernels, some input devices which has a left alt key cannot attach sysrq handler. Because the keybit bitmap in struct input_device_id for sysrq is not correctly initialized. KEY_LEFTALT is 56 which is greater than BITS_PER_LONG on 32-bit kernels. I found this problem when using a matrix keypad device which defines a KEY_LEFTALT (56) but doesn't have a KEY_O (24 == 56%32). Cc: Jiri Slaby <jslaby@suse.com> Signed-off-by:
Akinobu Mita <akinobu.mita@gmail.com> Acked-by:
Dmitry Torokhov <dmitry.torokhov@gmail.com> Signed-off-by:
-
Richard Genoud authored
commit b389f173 upstream. When using RS485 in half duplex, RX should be enabled when TX is finished, and stopped when TX starts. Before commit 0058f087 ("tty/serial: atmel: fix RS485 half duplex with DMA"), RX was not disabled in atmel_start_tx() if the DMA was used. So, collisions could happened. But disabling RX in atmel_start_tx() uncovered another bug: RX was enabled again in the wrong place (in atmel_tx_dma) instead of being enabled when TX is finished (in atmel_complete_tx_dma), so the transmission simply stopped. This bug was not triggered before commit 0058f087 ("tty/serial: atmel: fix RS485 half duplex with DMA") because RX was never disabled before. Moving atmel_start_rx() in atmel_complete_tx_dma() corrects the problem. Reported-by:
Gil Weber <webergil@gmail.com> Fixes: 0058f087Tested-by:
Richard Genoud <richard.genoud@gmail.com> Acked-by:
Alexandre Belloni <alexandre.belloni@free-electrons.com> Signed-off-by:
-
Mike Kravetz authored
commit e5bbc8a6 upstream. return_unused_surplus_pages() decrements the global reservation count, and frees any unused surplus pages that were backing the reservation. Commit 7848a4bf ("mm/hugetlb.c: add cond_resched_lock() in return_unused_surplus_pages()") added a call to cond_resched_lock in the loop freeing the pages. As a result, the hugetlb_lock could be dropped, and someone else could use the pages that will be freed in subsequent iterations of the loop. This could result in inconsistent global hugetlb page state, application api failures (such as mmap) failures or application crashes. When dropping the lock in return_unused_surplus_pages, make sure that the global reservation count (resv_huge_pages) remains sufficiently large to prevent someone else from claiming pages about to be freed. Analyzed by Paul Cassella. Fixes: 7848a4bf ("mm/hugetlb.c: add cond_resched_lock() in return_unused_surplus_pages()") Link: http://lkml.kernel.org/r/1483991767-6879-1-git-send-email-mike.kravetz@oracle.comSigned-off-by:
Mike Kravetz <mike.kravetz@oracle.com> Reported-by:
Paul Cassella <cassella@cray.com> Suggested-by:
Michal Hocko <mhocko@kernel.org> Cc: Masayoshi Mizuma <m.mizuma@jp.fujitsu.com> Cc: Naoya Horiguchi <n-horiguchi@ah.jp.nec.com> Cc: Aneesh Kumar <aneesh.kumar@linux.vnet.ibm.com> Cc: Hillf Danton <hillf.zj@alibaba-inc.com> Signed-off-by:
Andrew Morton <akpm@linux-foundation.org> Signed-off-by:
Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by:
-
Eric Ren authored
commit e7ee2c08 upstream. The crash happens rather often when we reset some cluster nodes while nodes contend fiercely to do truncate and append. The crash backtrace is below: dlm: C21CBDA5E0774F4BA5A9D4F317717495: dlm_recover_grant 1 locks on 971 resources dlm: C21CBDA5E0774F4BA5A9D4F317717495: dlm_recover 9 generation 5 done: 4 ms ocfs2: Begin replay journal (node 318952601, slot 2) on device (253,18) ocfs2: End replay journal (node 318952601, slot 2) on device (253,18) ocfs2: Beginning quota recovery on device (253,18) for slot 2 ocfs2: Finishing quota recovery on device (253,18) for slot 2 (truncate,30154,1):ocfs2_truncate_file:470 ERROR: bug expression: le64_to_cpu(fe->i_size) != i_size_read(inode) (truncate,30154,1):ocfs2_truncate_file:470 ERROR: Inode 290321, inode i_size = 732 != di i_size = 937, i_flags = 0x1 ------------[ cut here ]------------ kernel BUG at /usr/src/linux/fs/ocfs2/file.c:470! invalid opcode: 0000 [#1] SMP Modules linked in: ocfs2_stack_user(OEN) ocfs2(OEN) ocfs2_nodemanager ocfs2_stackglue(OEN) quota_tree dlm(OEN) configfs fuse sd_mod iscsi_tcp libiscsi_tcp libiscsi scsi_transport_iscsi af_packet iscsi_ibft iscsi_boot_sysfs softdog xfs libcrc32c ppdev parport_pc pcspkr parport joydev virtio_balloon virtio_net i2c_piix4 acpi_cpufreq button processor ext4 crc16 jbd2 mbcache ata_generic cirrus virtio_blk ata_piix drm_kms_helper ahci syscopyarea libahci sysfillrect sysimgblt fb_sys_fops ttm floppy libata drm virtio_pci virtio_ring uhci_hcd virtio ehci_hcd usbcore serio_raw usb_common sg dm_multipath dm_mod scsi_dh_rdac scsi_dh_emc scsi_dh_alua scsi_mod autofs4 Supported: No, Unsupported modules are loaded CPU: 1 PID: 30154 Comm: truncate Tainted: G OE N 4.4.21-69-default #1 Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.8.1-0-g4adadbd-20151112_172657-sheep25 04/01/2014 task: ffff88004ff6d240 ti: ffff880074e68000 task.ti: ffff880074e68000 RIP: 0010:[<ffffffffa05c8c30>] [<ffffffffa05c8c30>] ocfs2_truncate_file+0x640/0x6c0 [ocfs2] RSP: 0018:ffff880074e6bd50 EFLAGS: 00010282 RAX: 0000000000000074 RBX: 000000000000029e RCX: 0000000000000000 RDX: 0000000000000001 RSI: 0000000000000246 RDI: 0000000000000246 RBP: ffff880074e6bda8 R08: 000000003675dc7a R09: ffffffff82013414 R10: 0000000000034c50 R11: 0000000000000000 R12: ffff88003aab3448 R13: 00000000000002dc R14: 0000000000046e11 R15: 0000000000000020 FS: 00007f839f965700(0000) GS:ffff88007fc80000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 000000008005003b CR2: 00007f839f97e000 CR3: 0000000036723000 CR4: 00000000000006e0 Call Trace: ocfs2_setattr+0x698/0xa90 [ocfs2] notify_change+0x1ae/0x380 do_truncate+0x5e/0x90 do_sys_ftruncate.constprop.11+0x108/0x160 entry_SYSCALL_64_fastpath+0x12/0x6d Code: 24 28 ba d6 01 00 00 48 c7 c6 30 43 62 a0 8b 41 2c 89 44 24 08 48 8b 41 20 48 c7 c1 78 a3 62 a0 48 89 04 24 31 c0 e8 a0 97 f9 ff <0f> 0b 3d 00 fe ff ff 0f 84 ab fd ff ff 83 f8 fc 0f 84 a2 fd ff RIP [<ffffffffa05c8c30>] ocfs2_truncate_file+0x640/0x6c0 [ocfs2] It's because ocfs2_inode_lock() get us stale LVB in which the i_size is not equal to the disk i_size. We mistakenly trust the LVB because the underlaying fsdlm dlm_lock() doesn't set lkb_sbflags with DLM_SBF_VALNOTVALID properly for us. But, why? The current code tries to downconvert lock without DLM_LKF_VALBLK flag to tell o2cb don't update RSB's LVB if it's a PR->NULL conversion, even if the lock resource type needs LVB. This is not the right way for fsdlm. The fsdlm plugin behaves different on DLM_LKF_VALBLK, it depends on DLM_LKF_VALBLK to decide if we care about the LVB in the LKB. If DLM_LKF_VALBLK is not set, fsdlm will skip recovering RSB's LVB from this lkb and set the right DLM_SBF_VALNOTVALID appropriately when node failure happens. The following diagram briefly illustrates how this crash happens: RSB1 is inode metadata lock resource with LOCK_TYPE_USES_LVB; The 1st round: Node1 Node2 RSB1: PR RSB1(master): NULL->EX ocfs2_downconvert_lock(PR->NULL, set_lvb==0) ocfs2_dlm_lock(no DLM_LKF_VALBLK) - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - dlm_lock(no DLM_LKF_VALBLK) convert_lock(overwrite lkb->lkb_exflags with no DLM_LKF_VALBLK) RSB1: NULL RSB1: EX reset Node2 dlm_recover_rsbs() recover_lvb() /* The LVB is not trustable if the node with EX fails and * no lock >= PR is left. We should set RSB_VALNOTVALID for RSB1. */ if(!(kb_exflags & DLM_LKF_VALBLK)) /* This means we miss the chance to return; * to invalid the LVB here. */ The 2nd round: Node 1 Node2 RSB1(become master from recovery) ocfs2_setattr() ocfs2_inode_lock(NULL->EX) /* dlm_lock() return the stale lvb without setting DLM_SBF_VALNOTVALID */ ocfs2_meta_lvb_is_trustable() return 1 /* so we don't refresh inode from disk */ ocfs2_truncate_file() mlog_bug_on_msg(disk isize != i_size_read(inode)) /* crash! */ The fix is quite straightforward. We keep to set DLM_LKF_VALBLK flag for dlm_lock() if the lock resource type needs LVB and the fsdlm plugin is uesed. Link: http://lkml.kernel.org/r/1481275846-6604-1-git-send-email-zren@suse.comSigned-off-by:
Eric Ren <zren@suse.com> Reviewed-by:
Joseph Qi <jiangqi903@gmail.com> Cc: Mark Fasheh <mfasheh@versity.com> Cc: Joel Becker <jlbec@evilplan.org> Cc: Junxiao Bi <junxiao.bi@oracle.com> Signed-off-by:
-
Herbert Xu authored
commit 57ea52a8 upstream. The GRO fast path caches the frag0 address. This address becomes invalid if frag0 is modified by pskb_may_pull or its variants. So whenever that happens we must disable the frag0 optimization. This is usually done through the combination of gro_header_hard and gro_header_slow, however, the IPv6 extension header path did the pulling directly and would continue to use the GRO fast path incorrectly. This patch fixes it by disabling the fast path when we enter the IPv6 extension header path. Fixes: 78a478d0 ("gro: Inline skb_gro_header and cache frag0 virtual address") Reported-by:
Slava Shwartsman <slavash@mellanox.com> Signed-off-by:
Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by:
Eric Dumazet <edumazet@google.com> Signed-off-by:
David S. Miller <davem@davemloft.net> Signed-off-by:
-
Herbert Xu authored
commit 1272ce87 upstream. The GRO path has a fast-path where we avoid calling pskb_may_pull and pskb_expand by directly accessing frag0. However, this should only be done if we have enough tailroom in the skb as otherwise we'll have to expand it later anyway. This patch adds the check by capping frag0_len with the skb tailroom. Fixes: cb18978c ("gro: Open-code final pskb_may_pull") Reported-by:
-
Mark Rutland authored
commit ddc37832 upstream. On APQ8060, the kernel crashes in arch_hw_breakpoint_init, taking an undefined instruction trap within write_wb_reg. This is because Scorpion CPUs erroneously appear to set DBGPRSR.SPD when WFI is issued, even if the core is not powered down. When DBGPRSR.SPD is set, breakpoint and watchpoint registers are treated as undefined. It's possible to trigger similar crashes later on from userspace, by requesting the kernel to install a breakpoint or watchpoint, as we can go idle at any point between the reset of the debug registers and their later use. This has always been the case. Given that this has always been broken, no-one has complained until now, and there is no clear workaround, disable hardware breakpoints and watchpoints on Scorpion to avoid these issues. Signed-off-by:
Mark Rutland <mark.rutland@arm.com> Reported-by:
Linus Walleij <linus.walleij@linaro.org> Reviewed-by:
Stephen Boyd <sboyd@codeaurora.org> Acked-by:
Will Deacon <will.deacon@arm.com> Cc: Russell King <linux@armlinux.org.uk> Signed-off-by:
Russell King <rmk+kernel@arm.linux.org.uk> [bwh: Backported to 3.16: open-code read_cpuid_part()] Signed-off-by:
-
Johan Hovold authored
commit 55fa15b5 upstream. Revert to using direct register writes to set the divisor and line-control registers. A recent change switched to using the init vendor command to update these registers, something which also enabled support for CH341A devices. It turns out that simply setting bit 7 in the divisor register is sufficient to support CH341A and specifically prevent data from being buffered until a full endpoint-size packet (32 bytes) has been received. Using the init command also had the side-effect of temporarily deasserting the DTR/RTS signals on every termios change (including initialisation on open) something which for example could cause problems in setups where DTR is used to trigger a reset. Fixes: 4e46c410 ("USB: serial: ch341: reinitialize chip on reconfiguration") Signed-off-by:
Johan Hovold <johan@kernel.org> [bwh: Backported to 3.16: adjust context] Signed-off-by:
-
Johan Hovold authored
commit ce5e2928 upstream. Fix reset-resume handling which failed to resubmit the read and interrupt URBs, thereby leaving a port that was open before suspend in a broken state until closed and reopened. Fixes: 1ded7ea4 ("USB: ch341 serial: fix port number changed after resume") Fixes: 2bfd1c96 ("USB: serial: ch341: remove reset_resume callback") Signed-off-by:
-
Johan Hovold authored
commit f2950b78 upstream. Make sure to stop the interrupt URB before returning on errors during open. Fixes: 664d5df9 ("USB: usb-serial ch341: support for DTR/RTS/CTS") Signed-off-by:
-
Johan Hovold authored
commit 030ee7ae upstream. The modem-control signals are managed by the tty-layer during open and should not be asserted prematurely when set_termios is called from driver open. Also make sure that the signals are asserted only when changing speed from B0. Fixes: 664d5df9 ("USB: usb-serial ch341: support for DTR/RTS/CTS") Signed-off-by:
-
Johan Hovold authored
commit a20047f3 upstream. The private baud_rate variable is used to configure the port at open and reset-resume and must never be set to (and left at) zero or reset-resume and all further open attempts will fail. Fixes: aa91def4 ("USB: ch341: set tty baud speed according to tty struct") Fixes: 664d5df9 ("USB: usb-serial ch341: support for DTR/RTS/CTS") Signed-off-by:
-
Johan Hovold authored
commit 4e2da446 upstream. DTR and RTS will be asserted by the tty-layer when the port is opened and deasserted on close (if HUPCL is set). Make sure the initial state is not-asserted before the port is first opened as well. Fixes: 664d5df9 ("USB: usb-serial ch341: support for DTR/RTS/CTS") Signed-off-by:
-
Aidan Thornton authored
commit 4e46c410 upstream. Changing the LCR register after initialization does not seem to be reliable on all chips (particularly not on CH341A). Restructure initialization and configuration to always reinit the chip on configuration changes instead and pass the LCR register value directly to the initialization command. (Note that baud rates above 500kbaud are incorrect, but they're incorrect in the same way both before and after this patch at least on the CH340G. Fixing this isn't a priority as higher baud rates don't seem that reliable anyway.) Cleaned-up version of a patch by Grigori Goronzy Signed-off-by:
Aidan Thornton <makosoft@gmail.com> Reviewed-by:
Grigori Goronzy <greg@chown.ath.cx> Signed-off-by:
-
Aidan Thornton authored
commit 6fde8d29 upstream. No functional changes, this just gives names to some registers and USB requests based on Grigori Goronzy's work and WinChipTech's Linux driver (which reassuringly agree), then uses them in place of magic numbers. This also renames the misnamed BREAK2 register (actually UART config) Signed-off-by:
-
Nicolas PLANEL authored
commit aa91def4 upstream. The ch341_set_baudrate() function initialize the device baud speed according to the value on priv->baud_rate. By default the ch341_open() set it to a hardcoded value (DEFAULT_BAUD_RATE 9600). Unfortunately, the tty_struct is not initialized with the same default value. (usually 56700) This means that the tty_struct and the device baud rate generator are not synchronized after opening the port. Fixup is done by calling ch341_set_termios() if tty exist. Remove unnecessary variable priv->baud_rate setup as it's already done by ch341_port_probe(). Remove unnecessary call to ch341_set_{handshake,baudrate}() in ch341_open() as there already called in ch341_configure() and ch341_set_termios() Signed-off-by:
Nicolas PLANEL <nicolas.planel@enovance.com> Signed-off-by:
-
Johan Hovold authored
commit 394a1033 upstream. Remove redundant call to ch341_close from error path when submission of the interrupt urb fails in open. Signed-off-by:
-
Nicholas Mc Guire authored
commit fac69d0e upstream. Add the missing declarations of basic string functions to string.h to allow a clean build. Fixes: 5be86566 ("String-handling functions for the new x86 setup code.") Signed-off-by:
Nicholas Mc Guire <hofrat@osadl.org> Link: http://lkml.kernel.org/r/1483781911-21399-1-git-send-email-hofrat@osadl.orgSigned-off-by:
Thomas Gleixner <tglx@linutronix.de> Signed-off-by:
-
Alex Deucher authored
commit 8a08403b upstream. fixes: https://bugs.freedesktop.org/show_bug.cgi?id=98897 https://bugs.launchpad.net/bugs/1651981Acked-by:
Edward O'Callaghan <funfunctor@folklore1984.net> Signed-off-by:
Alex Deucher <alexander.deucher@amd.com> Cc: Adrian Fiergolski <A.Fiergolski@gmail.com> Signed-off-by:
-
Arvind Yadav authored
commit 064c3db9 upstream. Here, If devm_ioremap will fail. It will return NULL. Then hpriv->base = NULL - 0x20000; Kernel can run into a NULL-pointer dereference. This error check will avoid NULL pointer dereference. Signed-off-by:
Arvind Yadav <arvind.yadav.cs@gmail.com> Signed-off-by:
Tejun Heo <tj@kernel.org> Signed-off-by:
-
Sergei Shtylyov authored
commit 0f1f9cbc upstream. The R8A7740 GEther controller supports the packet checksum offloading but the 'hw_crc' (bad name, I'll fix it) flag isn't set in the R8A7740 data, thus CSMR isn't cleared... Fixes: 73a0d907 ("net: sh_eth: add support R8A7740") Signed-off-by:
Sergei Shtylyov <sergei.shtylyov@cogentembedded.com> Signed-off-by:
-
Sergei Shtylyov authored
commit 978d3639 upstream. As the SH77{34|63} manuals are freely available, I've checked the EESIPR values written against the manuals, and they appeared to set the reserved bits 11-15 (which should be 0 on write). Fix those EESIPR values. Fixes: 380af9e3 ("net: sh_eth: CPU dependency code collect to "struct sh_eth_cpu_data"") Fixes: f5d12767 ("sh_eth: get SH77{34|63} support out of #ifdef") Signed-off-by:
-
Dave Martin authored
commit fd7c9914 upstream. Ensure that if userspace supplies insufficient data to PTRACE_SETREGSET to fill all the registers, the thread's old registers are preserved. Signed-off-by:
Dave Martin <Dave.Martin@arm.com> Signed-off-by:
Chris Metcalf <cmetcalf@mellanox.com> Signed-off-by:
-
Greg Kroah-Hartman authored
commit 1ebb7114 upstream. Make sure we have enough of a report structure to validate before looking at it. Reported-by:
Benoit Camredon <benoit.camredon@airbus.com> Tested-by:
Jiri Kosina <jkosina@suse.cz> Signed-off-by:
-
Rolf Eike Beer authored
commit 3659f98b upstream. Nothing in this minimal script seems to require bash. We often run these tests on embedded devices where the only shell available is the busybox ash. Use sh instead. Signed-off-by:
Rolf Eike Beer <eb@emlix.com> Signed-off-by:
Shuah Khan <shuahkh@osg.samsung.com> Signed-off-by:
-
Alan Stern authored
commit 0a8fd134 upstream. When checking a new device's descriptors, the USB core does not check for duplicate endpoint addresses. This can cause a problem when the sysfs files for those endpoints are created; trying to create multiple files with the same name will provoke a WARNING: WARNING: CPU: 2 PID: 865 at fs/sysfs/dir.c:31 sysfs_warn_dup+0x8a/0xa0 sysfs: cannot create duplicate filename '/devices/platform/dummy_hcd.0/usb2/2-1/2-1:64.0/ep_05' Kernel panic - not syncing: panic_on_warn set ... CPU: 2 PID: 865 Comm: kworker/2:1 Not tainted 4.9.0-rc7+ #34 Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS Bochs 01/01/2011 Workqueue: usb_hub_wq hub_event ffff88006bee64c8 ffffffff81f96b8a ffffffff00000001 1ffff1000d7dcc2c ffffed000d7dcc24 0000000000000001 0000000041b58ab3 ffffffff8598b510 ffffffff81f968f8 ffffffff850fee20 ffffffff85cff020 dffffc0000000000 Call Trace: [< inline >] __dump_stack lib/dump_stack.c:15 [<ffffffff81f96b8a>] dump_stack+0x292/0x398 lib/dump_stack.c:51 [<ffffffff8168c88e>] panic+0x1cb/0x3a9 kernel/panic.c:179 [<ffffffff812b80b4>] __warn+0x1c4/0x1e0 kernel/panic.c:542 [<ffffffff812b8195>] warn_slowpath_fmt+0xc5/0x110 kernel/panic.c:565 [<ffffffff819e70ca>] sysfs_warn_dup+0x8a/0xa0 fs/sysfs/dir.c:30 [<ffffffff819e7308>] sysfs_create_dir_ns+0x178/0x1d0 fs/sysfs/dir.c:59 [< inline >] create_dir lib/kobject.c:71 [<ffffffff81fa1b07>] kobject_add_internal+0x227/0xa60 lib/kobject.c:229 [< inline >] kobject_add_varg lib/kobject.c:366 [<ffffffff81fa2479>] kobject_add+0x139/0x220 lib/kobject.c:411 [<ffffffff82737a63>] device_add+0x353/0x1660 drivers/base/core.c:1088 [<ffffffff82738d8d>] device_register+0x1d/0x20 drivers/base/core.c:1206 [<ffffffff82cb77d3>] usb_create_ep_devs+0x163/0x260 drivers/usb/core/endpoint.c:195 [<ffffffff82c9f27b>] create_intf_ep_devs+0x13b/0x200 drivers/usb/core/message.c:1030 [<ffffffff82ca39d3>] usb_set_configuration+0x1083/0x18d0 drivers/usb/core/message.c:1937 [<ffffffff82cc9e2e>] generic_probe+0x6e/0xe0 drivers/usb/core/generic.c:172 [<ffffffff82caa7fa>] usb_probe_device+0xaa/0xe0 drivers/usb/core/driver.c:263 This patch prevents the problem by checking for duplicate endpoint addresses during enumeration and skipping any duplicates. Signed-off-by:
Alan Stern <stern@rowland.harvard.edu> Reported-by:
Andrey Konovalov <andreyknvl@google.com> Tested-by:
-
Oliver Neukum authored
commit 674aea07 upstream. This device gives the following error on detection. xhci_hcd 0000:00:11.0: ERROR Transfer event for disabled endpoint or incorrect stream ring The same error is not seen when it is added to unusual_device list with US_FL_NO_REPORT_OPCODES passed. Signed-off-by:
George Cherian <george.cherian@cavium.com> Signed-off-by:
Oliver Neukum <oneukun@suse.com> Signed-off-by:
-
Geert Uytterhoeven authored
commit 3bc02bce upstream. If CONFIG_PM=n: drivers/usb/core/hub.c:107: warning: ‘hub_usb3_port_prepare_disable’ declared inline after being called drivers/usb/core/hub.c:107: warning: previous declaration of ‘hub_usb3_port_prepare_disable’ was here To fix this, move hub_port_disable() after hub_usb3_port_prepare_disable(), and adjust forward declarations. Fixes: 37be6676 ("usb: hub: Fix auto-remount of safely removed or ejected USB-3 devices") Signed-off-by:
Geert Uytterhoeven <geert@linux-m68k.org> Signed-off-by:
-
Tony Lindgren authored
commit 8c300fe2 upstream. When unloading omap2430, we can get the following splat: WARNING: CPU: 1 PID: 295 at kernel/irq/manage.c:1478 __free_irq+0xa8/0x2c8 Trying to free already-free IRQ 4 ... [<c01a8b78>] (free_irq) from [<bf0aea84>] (musbhs_dma_controller_destroy+0x28/0xb0 [musb_hdrc]) [<bf0aea84>] (musbhs_dma_controller_destroy [musb_hdrc]) from [<bf09f88c>] (musb_remove+0xf0/0x12c [musb_hdrc]) [<bf09f88c>] (musb_remove [musb_hdrc]) from [<c056a384>] (platform_drv_remove+0x24/0x3c) ... This is because the irq number in use is 260 nowadays, and the dma controller is using u8 instead of int. Fixes: 6995eb68 ("USB: musb: enable low level DMA operation for Blackfin") Signed-off-by:
Tony Lindgren <tony@atomide.com> [b-liu@ti.com: added Fixes tag] Signed-off-by:
Bin Liu <b-liu@ti.com> Signed-off-by:
-
James Hogan authored
commit 32eb12a6 upstream. Flush the KVM entry code from the icache on all CPUs, not just the one that built the entry code. Signed-off-by:
James Hogan <james.hogan@imgtec.com> Cc: Paolo Bonzini <pbonzini@redhat.com> Cc: "Radim Krčmář" <rkrcmar@redhat.com> Cc: Ralf Baechle <ralf@linux-mips.org> Cc: linux-mips@linux-mips.org Cc: kvm@vger.kernel.org Signed-off-by:
Radim Krčmář <rkrcmar@redhat.com> [bwh: Backported to 3.16: adjust filename] Signed-off-by:
-
Lukasz Odzioba authored
commit dd853fd2 upstream. A negative number can be specified in the cmdline which will be used as setup_clear_cpu_cap() argument. With that we can clear/set some bit in memory predceeding boot_cpu_data/cpu_caps_cleared which may cause kernel to misbehave. This patch adds lower bound check to setup_disablecpuid(). Boris Petkov reproduced a crash: [ 1.234575] BUG: unable to handle kernel paging request at ffffffff858bd540 [ 1.236535] IP: memcpy_erms+0x6/0x10 Signed-off-by:
Lukasz Odzioba <lukasz.odzioba@intel.com> Acked-by:
Borislav Petkov <bp@suse.de> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: andi.kleen@intel.com Cc: bp@alien8.de Cc: dave.hansen@linux.intel.com Cc: luto@kernel.org Cc: slaoub@gmail.com Fixes: ac72e788 ("x86: add generic clearcpuid=... option") Link: http://lkml.kernel.org/r/1482933340-11857-1-git-send-email-lukasz.odzioba@intel.comSigned-off-by:
Ingo Molnar <mingo@kernel.org> Signed-off-by:
-
Sergei Shtylyov authored
commit 71eae1ca upstream. The RX descriptor word 0 on SH7734 has the RFS[9:0] field in bits 16-25 (bits 0-15 usually used for that are occupied by the packet checksum). Thus we need to set the 'shift_rd0' field in the SH7734 SoC data... Fixes: f0e81fec ("net: sh_eth: Add support SH7734") Signed-off-by:
-
Takashi Iwai authored
commit c7efff92 upstream. Although the old quirk table showed ASUS X71SL with ALC663 codec being compatible with asus-mode3 fixup, the bugzilla reporter explained that asus-model8 fits better for the dual headphone controls. So be it. Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=191781Signed-off-by:
Takashi Iwai <tiwai@suse.de> Signed-off-by:
-
Florian Fainelli authored
commit 38e5a855 upstream. Inserting the TSB means adding an extra 8 bytes in front the of packet that is going to be used as metadata information by the TDMA engine, but stripped off, so it does not really help with the packet padding. For some odd packet sizes that fall below the 60 bytes payload (e.g: ARP) we can end-up padding them after the TSB insertion, thus making them 64 bytes, but with the TDMA stripping off the first 8 bytes, they could still be smaller than 64 bytes which is required to ingress the switch. Fix this by swapping the padding and TSB insertion, guaranteeing that the packets have the right sizes. Fixes: 80105bef ("net: systemport: add Broadcom SYSTEMPORT Ethernet MAC driver") Signed-off-by:
Florian Fainelli <f.fainelli@gmail.com> Signed-off-by:
-
Alexander Usyskin authored
commit e09ee853 upstream. The credentials handling was pushed to the write handlers but error handling wasn't done properly. Move write callbacks to completion queue to destroy them and to notify a blocked writer about the failure Fixes: 136698e5 (mei: push credentials inside the irq write handler) Signed-off-by:
Alexander Usyskin <alexander.usyskin@intel.com> Signed-off-by:
Tomas Winkler <tomas.winkler@intel.com> Signed-off-by:
-
Huang Rui authored
commit 432abf68 upstream. The generic command buffer entry is 128 bits (16 bytes), so the offset of tail and head pointer should be 16 bytes aligned and increased with 0x10 per command. When cmd buf is full, head = (tail + 0x10) % CMD_BUFFER_SIZE. So when left space of cmd buf should be able to store only two command, we should be issued one COMPLETE_WAIT additionally to wait all older commands completed. Then the left space should be increased after IOMMU fetching from cmd buf. So left check value should be left <= 0x20 (two commands). Signed-off-by:
Huang Rui <ray.huang@amd.com> Fixes: ac0ea6e9 ('x86/amd-iommu: Improve handling of full command buffer') Signed-off-by:
Joerg Roedel <jroedel@suse.de> Signed-off-by:
-
Takashi Iwai authored
commit 85bcf96c upstream. ASUS ROG Ranger VIII with ALC1150 codec requires the extra GPIO pin to up for the front panel. Just use the existing fixup for setting up the GPIO pins. Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=189411Signed-off-by:
-
Johan Hovold authored
commit ef079936 upstream. Fix NULL-pointer dereference in open() should a malicious device lack the expected endpoints: Unable to handle kernel NULL pointer dereference at virtual address 00000030 .. [<bf06a6b0>] (ti_open [ti_usb_3410_5052]) from [<bf02e118>] (serial_port_activate+0x68/0x98 [usbserial]) Fixes: 1da177e4 ("Linux-2.6.12-rc2") Signed-off-by:
-
Johan Hovold authored
commit cc090924 upstream. Fix NULL-pointer dereference in open() should the device lack the expected endpoints: Unable to handle kernel NULL pointer dereference at virtual address 00000030 ... PC is at spcp8x5_open+0x30/0xd0 [spcp8x5] Fixes: 619a6f1d ("USB: add usb-serial spcp8x5 driver") Signed-off-by:
-
