Use the AM33XX pinmux IOPAD macro to define the physical address instead
of the offset from the padconf address. It makes the DTS easier to read
since matches the addresses listed in the Technical Reference Manual.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Use the AM33xx pinmux IOPAD macro to define the physical address instead
of the offset from the padconf address. It makes the DTS easier to read
since matches the addresses listed in the Technical Reference Manual.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Use the OMAP3 pinmux IOPAD macro to define the physical address instead
of the offset from the padconf address. It makes the DTS easier to read
since matches the addresses listed in the Technical Reference Manual.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

On am437x-gp-evm, pixcir_i2c_ts can wakeup the system from low power
state via pinctrl and IO daisy chain using generic wakeirq framework.
With commit 3fffd128 ("i2c: allow specifying separate wakeup
interrupt in device tree") i2c core allows optional wakeirq to be
specified via device tree. Add wakeup irq entry to enable pixcir_i2c_ts
to wake the system from low power state.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

I see that people are still sending emails to my old address (that no
longer exists) since is the one mentioned in the IGEP DTS. Replace it
with my current email address to avoid this.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

With the current implementation of GPIO hogging and with
gpio-pcf857x is built as module, ethernet doesn't work on boot
and doesn't throw any error/warning to user. Ethernet becomes
operational when inserting gpio-pcf857x module, even this time
there is no error/warning logs to user that ethernet is
operational.

When using with NFS rootfs and gpio-pcf857x as module, board
doesn't boot as it doesn't get any ip address and doesn't throw
any error/warning. To over come this, now cpsw driver tries to
get mode-gpios. When gpio-pcf857x is built as module it will
throw error, so that user can decide either to built in
gpio-pcf857x to continue with nfs boot or choose alternate rootfs
filesystem like sd/ramdisk.

When using mmc/ramdisk as root fs, cpsw will probe defer and
re-probes again when gpio-pcf857x module is inserted and ethernet
becomes operational.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

With omap5-board-common.dtsi, we can now easily add support for various omap5
board variants. Let's add minimal support for isee igepv5.

So far I've tested that basic things work, such as serial, USB Ethernet, HDMI
and WLAN.

Note that like omap5-uevm, these boards seem to need to reserve 16MB for a
trap section as in commit 03178c66 ("ARM: dts: omap5-evm: Update
available memory to 2032 MB") and also noted in a u-boot commit at
http://marc.info/?l=u-boot&m=134376852603255 and also at
http://patchwork.ozlabs.org/patch/159881/.

Not sure why this is not needed for omap5-cm-t54.dts, maybe because of
different u-boot configuration.
Signed-off-by: Tony Lindgren <tony@atomide.com>

Looks like thevarious omap5-uevm models and igepv5 are very similar. So let's
create omap5-board-common.dtsi to allow fixing up things properly for mainline
kernel to support all these.

Even if we eventually end up having only PMIC + MMC + eMMC + SDIO WLAN + SATA +
USB + HDMI configuration in the omap5-board-common.dtsi, this is the easiest
way to add support for other boards rather than diffing various versions of
out of tree dts files.

My guess is that also omap5-sbc-t54.dts can use this, but I don't have that
board so that will need to be dealt with later on.
Signed-off-by: Tony Lindgren <tony@atomide.com>

Commit 99f84cae ("ARM: dts: add wl12xx/wl18xx bindings") added
device tree bindings for the TI WLAN SDIO on many omap variants.

I recall wondering how come omap5-uevm did not have the WLAN
added and this issue has been bugging me for a while now, and
I finally tracked it down to a bad pinmux regression, and a missing
deferred probe handling for the 32k clock from palmas that's
requested by twl6040.

Basically 392adaf7 ("ARM: dts: omap5-evm: Add mcspi data")
added pin muxing for mcspi4 that conflicts with the onboard
WLAN. While some omap5-uevm don't have WLAN populated, the
pins are not reused for other devices. And as the SDIO bus
should be probed, let's try to enable WLAN by default.

Let's fix the regression and add the WLAN configuration as
done for the other boards in 99f84cae ("ARM: dts: add
wl12xx/wl18xx bindings"). And let's use the new MMC pwrseq for
the 32k clock as suggested by Javier Martinez Canillas
<javier@dowhile0.org>.

Note that without a related deferred probe fix for twl6040,
the 32k clock is not initialized if palmas-clk is a module
and twl6040 is built-in.

Let's also use the generic "non-removable" instead of the
legacy "ti,non-removable" property while at it.

And finally, note that omap5 seems to require WAKEUP_EN for
the WLAN GPIO interrupt.

Fixes: 392adaf7 ("ARM: dts: omap5-evm: Add mcspi data")
Cc: Sourav Poddar <sourav.poddar@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Use the macro instead of absolute register offsets to make the code more
readable as the values now match register addresses from the datasheet.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

As per mmc device tree binding documentation card detect gpio has
to be active low signal. When a hardware is designed with active
high card detect, gpio polarity has to be changed with
cd-inverted dt property.

In DRA74x, DRA72x and AM57xx EVMs the card detect gpio is
designed as active low gpio. So correcting the dt card detect
gpio definition.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

As per mmc device tree binding documentation card detect gpio has
to be active low signal. When a hardware is designed with active
high card detect, gpio polarity has to be changed with
cd-inverted dt property.

In AM43xx the card detect gpio is designed as active low gpio.
So correcting the dt card detect gpio definition.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

As per mmc device tree binding documentation card detect gpio has
to be active low signal. When a hardware is designed with active
high card detect, gpio polarity has to be changed with
cd-inverted dt property.

In AM335x the card detect gpio is designed as active low gpio.
So correcting the dt card detect gpio definition.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

uart2 pinmux is already defined in omap3-igep0020-common.dtsi, remove
the duplicate node.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Use tabs instead of spaces for indentation.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

The card detect GPIO is using IRQ_TYPE_LEVEL_LOW in the GPIO flag cells
but this defined constant is meant to be used for a IRQ and not a GPIO.
So instead use GPIO_ACTIVE_LOW that seems to be the original intention.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

The DRA74x family of SoCs have a second DSP, that also has
two MMUs just like the DSP1 subsystem. Add the IOMMU nodes
for this DSP2 subsystem in disabled state to the DRA74x
specific DTS file, the nodes would need to be enabled
appropriately in the respective board DTS files.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

The DRA7xx family of SOCs have two IPUs and one DSP processor
subsystems in common. The IOMMU DT nodes have been added for
these processor subsystems, and have been disabled by default.

These MMUs are very similar to those on OMAP4 and OMAP5, with
the only difference being the presence of a second MMU within
the DSP subsystem for the EDMA port. The DSP IOMMUs also need
an additional 'ti,syscon-mmuconfig' property compared to the
IPU IOMMUs.

NOTE: The enabling of these nodes is left to the respective
board dts files.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

The DSP_SYSTEM sub-module is a dedicated system control logic
module present within a DRA7 DSP processor sub-system. This
module is responsible for power management, clock generation
and connection to the device PRCM module.

Add a syscon node for this module for the DSP2 processor
sub-system. This is added as a syscon node as it is a common
configuration module that can be used by the different IOMMU
instances and the corresponding remoteproc device.

The node is added to the dra74x.dtsi file, as the DSP2 processor
subsystem is usually present only on the DRA74x variants of the
DRA7 SoC family.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

The DSP_SYSTEM sub-module is a dedicated system control logic
module present within a DRA7 DSP processor sub-system. This
module is responsible for power management, clock generation
and connection to the device PRCM module.

Add a syscon node for this module for the DSP1 processor
sub-system. This is added as a syscon node as it is a common
configuration module that can be used by the different IOMMU
instances and the corresponding remoteproc device.

The node is added to the common dra7.dtsi file, as the DSP1
processor sub-system is mostly common across all the variants
of the DRA7 SoC family.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Many OMAP2+ DTS are not using the defined constants to express
the GPIO polarity. Replace these so the DTS are easier to read.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

SeeedStudio BeagleBone Green (BBG) is clone of the BeagleBone Black (BBB) minus
the HDMI port and addition of two Grove connectors (i2c2 and usart2).

This board can be identified by the 1A value after A335BNLT (BBB) in the at24 eeprom:
1A: [aa 55 33 ee 41 33 33 35  42 4e 4c 54 1a 00 00 00 |.U3.A335BNLT....|]

http://beagleboard.org/green
http://www.seeedstudio.com/wiki/Beaglebone_greenSigned-off-by: Robert Nelson <robertcnelson@gmail.com>
CC: Tony Lindgren <tony@atomide.com>
CC: Jason Kridner <jkridner@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Enable the System Mailboxes 5 and 6 and the corresponding child
sub-mailbox (IPC 3.x) nodes for the Beagle X15 EVM boards. This
is needed to enable communication with the respective remote
processors IPU1, IPU2, DSP1 and DSP2 from the MPU.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Enable the System Mailboxes 5 and 6 and the corresponding
child sub-mailbox (IPC 3.x) nodes for the DRA72 EVM board.
This is needed to enable communication with the respective
remote processors IPU1, IPU2, and DSP1 from the MPU.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Enable the System Mailboxes 5 and 6 and the corresponding
child sub-mailbox (IPC 3.x) nodes for the DRA7 EVM board.
This is needed to enable communication with the respective
remote processors IPU1, IPU2, DSP1 and DSP2 from the MPU.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Add the sub-mailbox nodes that are used to communicate between
MPU and the remote processors IPU1, IPU2 and DSP1. These match the
respective node definitions on DRA74x to maintain compatibility for
the equivalent remote processors. There is no DSP2 on DRA72x, and
so the corresponding sub-mailbox node is not added.

These sub-mailbox nodes are added to match the hard-coded mailbox
configuration used within the TI IPC 3.x software package. The
Dual-Cortex M4 IPU1 and IPU2 processor sub-systems are assumed to
be running in SMP-mode, and hence only a single sub-mailbox node
is added for each.

All these sub-mailbox nodes are left in disabled state, and should
be enabled (and modified if needed) as per the individual product
configuration in the corresponding board dts files.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Add the sub-mailbox nodes that are used to communicate between
MPU and the remote processors IPU1, IPU2, DSP1 and DSP2.

The sub-mailbox nodes utilize the System Mailbox instances 5 and 6.
These sub-mailbox nodes are added to match the hard-coded mailbox
configuration used within the TI IPC 3.x software package. The
Dual-Cortex M4 IPU1 and IPU2 processor sub-systems are assumed to
be running in SMP-mode, and hence only a single sub-mailbox node
is added for each.

All these sub-mailbox nodes are left in disabled state, and should
be enabled (and modified if needed) as per the individual product
configuration in the corresponding board dts files.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Cleaned up the regulators on the wega board. Created a simple bus,
renamed the regulators according to the schematics and added missing
regulator on wega.
Signed-off-by: Teresa Remmet <t.remmet@phytec.de>
Signed-off-by: Tony Lindgren <tony@atomide.com>

dra7-evm has 2 gpio keys wired through TS_LCD_GPIO3, TS_LCD_GPIO4
which in turn connected to PCF8575 GPIO pcf_lcd: gpio@20 expander
pins 2 and 3.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

dra7-evm has 4 user gpio leds connected to PCF8575 GPIO pcf_lcd:
gpio@20 expander pins [4,5,6,7], so add corresponding DT nodes.

Do not enable any triggers by default as not all of them are proved
to work on -RT.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

This patch adds DT definition for CF8575 GPIO pcf_lcd: gpio@20
expander which is connected to i2c bus 1 and has slave address 0x20.
It allows to control:
- tc_lcd gpios, pins p0-p3
- user leds, pins p4-p7
- control LCD panel power, p15

PCF8575 GPIO pcf_lcd: gpio@20 expander supports interrupt controller
functionality and its INT line is connected to dra7 GPIO6.11 pin.

Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

The analog audio setup consists of:
McASP3 <-> tlv320aic3104 codec
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

The DVDD is supplied via TPS77018DBVT fixed regulator from vdd_3v3
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

The board uses tlv320aic3106 codec connected to McASP3. The master clock
for the codec and McASP3 is coming from ATL2.
McASP3 is the master on the I2S bus.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

The GPIO expander's p1 on i2c5 bus 0x26 address is used for selecting
between audio and VIN6 functionality. For VIN6 use an add on card is
needed while audio is present on the board itself.
Select the audio functionality over the VIN6 in the dts file.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

The DVDD is supplied via TPS77018DBVT fixed regulator from evm_3v3
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Darren Etheridge <detheridge@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

The board uses tlv320aic3106 codec connected to McASP3. The master clock
for the codec and McASP3 is coming from ATL2.
McASP3 is the master on the I2S bus.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

This GPIO expander is used for controlling various muxes on the board.
By default select audio functionality over VIN6 by setting the P1
(vin6_sel_s0) pin to low.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

TPS77018DBVT is used to create 1.8V from avm_3v3_sw's 3.3V connected to
aic3106's DVDD.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Use the name for the supply as it is in the schematics since the same
supply is used for other peripherals than MMC2, like audio.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>