Change the locking flow to support RX and TX locks, splitting
the single lock to two will allow inserting rules in parallel
for RX and TX parts of the FDB.

Locking the dr_domain will be done by locking the RX domain
and the TX domain locks, this is mostly used for control operations
on the dr_domain. When inserting rules for RX or TX the single
nic_doamin RX or TX lock will be used. Splitting the lock is safe since
RX and TX domains are logically separated from each other, shared
objects such the send-ring and memory pool are protected by locks.
Signed-off-by: Alex Vesker <valex@mellanox.com>
Reviewed-by: Mark Bloch <markb@mellanox.com>
Reviewed-by: Erez Shitrit <erezsh@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

Adding this lock will allow writing steering entries without
locking the dr_domain and allow parallel insertion.
Signed-off-by: Alex Vesker <valex@mellanox.com>
Reviewed-by: Mark Bloch <markb@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

The HW is optimized for IPv4/IPv6. For such cases, pending capability,
avoid matching on ethertype, and use ip_version field instead.
Signed-off-by: Eli Britstein <elibr@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

Set ethertype match in a helper function as a pre-step towards
optimizing it.
Signed-off-by: Eli Britstein <elibr@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

Add mutex destroy calls to balance with mutex_init() done in the init
path.
Signed-off-by: Parav Pandit <parav@mellanox.com>
Reviewed-by: Moshe Shemesh <moshe@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

Use change upper event to detect slave representor from
enslaving/unslaving to/from lag device.

On enslaving event, call mlx5_enslave_rep() API to create, add
this slave representor shadow entry to the slaves list of
bond_metadata structure representing master lag device and use
its metadata to setup ingress acl metadata header.

On unslaving event, resetting the vport of unslaved representor
to use its default ingress/egress acls and rx rules with its
default_metadata.

The last slave will free the shared bond_metadata and its
unique metadata.
Signed-off-by: Vu Pham <vuhuong@mellanox.com>
Reviewed-by: Parav Pandit <parav@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

Bonded slave representors' vports must share a unique metadata
for match.

On enslaving event of slave representor to lag device, allocate
new unique "bond_metadata" for match if this is the first slave.
The subsequent enslaved representors will share the same unique
"bond_metadata".

On unslaving event of slave representor, reset the slave
representor's vport to use its own default metadata.

Replace ingress acl and rx rules of the slave representors' vports
using new vport->bond_metadata.
Signed-off-by: Vu Pham <vuhuong@mellanox.com>
Reviewed-by: Parav Pandit <parav@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

Introduce infrastructure to create unique metadata for match
for vport without depending on vport_num. Vport uses its
default metadata for match in standalone configuration but
will share a different unique "bond_metadata" for match with
other vports in bond configuration.

Using ida to generate unique metadata for match for vports
in default and bond configurations.

Introduce APIs to generate, free metadata for match.
Introduce APIs to set vport's bond_metadata and replace its
ingress acl rules with bond_metatada.
Signed-off-by: Vu Pham <vuhuong@mellanox.com>
Reviewed-by: Parav Pandit <parav@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Reviewed-by: Mark Bloch <markb@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

Adding bond_metadata and its slave entries to represent a lag device
and its slaves VF representors. Bond_metadata structure includes a
unique metadata shared by slaves VF respresentors, and a list of slaves
representors slave entries.

On enslaving event, create a bond_metadata structure representing
the upper lag device of this slave representor if it has not been
created yet. Create and add entry for the slave representor to the
slaves list.

On unslaving event, free the slave entry of the slave representor.
On the last unslave event, free the bond_metadata structure and its
resources.

Introduce APIs to create and remove bond_metadata and its resources,
enslave and unslave VF representor slave entries.
Signed-off-by: Vu Pham <vuhuong@mellanox.com>
Reviewed-by: Parav Pandit <parav@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

When a bond device is created over one or more non uplink representors,
and when a flow rule is offloaded to such bond device, offload a rule
to the active lower device.

Assuming that this is active-backup lag, the rules should be offloaded
to the active lower device which is the representor of the direct
path (not the failover).
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Parav Pandit <parav@mellanox.com>
Signed-off-by: Vu Pham <vuhuong@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

Currently offloading a rule over a tc block shared by multiple
representors fails because an e-switch global hashtable to keep
the mapping from tc cookies to mlx5e flow instances is used, and
tc block sharing offloads the same rule/cookie multiple times,
each time for different representor sharing the tc block.

Changing the implementation and behavior by acknowledging and returning
success if the same rule/cookie is offloaded again to other slave
representor sharing the tc block by setting, checking and comparing
the netdev that added the rule first.
Signed-off-by: Vu Pham <vuhuong@mellanox.com>
Reviewed-by: Parav Pandit <parav@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

Register a notifier block to handle netdev events for bond device
of non-uplink representors to support eswitch vports bonding.

When a non-uplink representor is a lower dev (slave) of bond and
becomes active, adding egress acl forward-to-vport rule of all slave
netdevs (active + standby) to forward to this representor's vport. Use
change lower netdev event to do this.

Use change upper event to detect slave representor unslaved from lag
device to delete its vport egress acl forward rule if any.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Vu Pham <vuhuong@mellanox.com>
Reviewed-by: Parav Pandit <parav@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

By default, e-switch vport's egress acl just forward packets to its
counterpart NIC vport using existing egress acl table.

During port failover in bonding scenario where two VFs representors
are bonded, the egress acl forward-to-vport rule will be added to
the existing egress acl table of e-switch vport of passive/inactive
slave representor to forward packets to other NIC vport ie. the active
slave representor's NIC vport to handle egress "failover" traffic.

Enable egress acl and have APIs to create and destroy egress acl
forward-to-vport rule and group.
Signed-off-by: Vu Pham <vuhuong@mellanox.com>
Reviewed-by: Parav Pandit <parav@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

Restructure the eswitch ingress acl codes into eswitch directory
and different files:
. Acl ingress helper functions to acl_helper.c/h
. Acl ingress functions used in offloads mode to acl_ingress_ofld.c
. Acl ingress functions used in legacy mode to acl_ingress_lgy.c

This patch does not change any functionality.
Signed-off-by: Vu Pham <vuhuong@mellanox.com>

Refactor the egress acl codes so that offloads and legacy modes
can configure specifically their own needs of egress acl table,
groups and rules. While at it, restructure the eswitch egress
acl codes into eswitch directory and different files:
. Acl egress helper functions to acl_helper.c/h
. Acl egress functions used in offloads mode to acl_egress_ofld.c
. Acl egress functions used in legacy mode to acl_egress_lgy.c

This patch does not change any functionality.
Signed-off-by: Vu Pham <vuhuong@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

Add support for Atheros 100Base-T PHYs. The only difference seems to be
the ability to test 2 pairs instead of 4 and the lack of 1000Base-T
specific register.

Only the ATH9331 was tested with this patch.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Andrew Lunn says:

====================
Raw PHY TDR data

Some ethernet PHYs allow access to raw TDR data in addition to summary
diagnostics information. Add support for retrieving this data via
netlink ethtool. The basic structure in the core is the same as for
normal phy diagnostics, the PHY driver simply uses different helpers
to fill the netlink message with different data.

There is a graphical tool under development, as well a ethtool(1)
which can dump the data as text and JSON.

A patched ethtool(1) can be found in
https://github.com/lunn/ethtool.git feature/cable-test-v5

Thanks for Chris Healy for lots of testing.

v2:
See the individual patches but:

Pass distances in centimeters, not meters

Allow the PHY to round distances to what it supports and report what
it actually used along with the results.

Make the Marvell PHY use steps a multiple of 0.805 meters, its native
step size.

v3:
Move the TDR configuration into a structure
Add a range check on step
Use NL_SET_ERR_MSG_ATTR() when appropriate
Move TDR configuration into a nest
Document attributes in the request
Unsquash the last two patches
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

When performing a TDR measurement for a short distance, the pulse
width should be low, to help differentiate between the outgoing pulse
and any reflection. For longer distances, the pulse should be wider,
to help with attenuation.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

Getting the TDR data requires a large number of MDIO bus
transactions. The number can however be reduced if the page is only
changed once. Add the needed locking to allow this, and make use of
unlocked read/write methods where needed.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

Allow the user to configure where on the cable the TDR data should be
retrieved, in terms of first and last sample, and the step between
samples. Also add the ability to ask for TDR data for just one pair.

If this configuration is not provided, it defaults to 1-150m at 1m
intervals for all pairs.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>

v3:
Move the TDR configuration into a structure
Add a range check on step
Use NL_SET_ERR_MSG_ATTR() when appropriate
Move TDR configuration into a nest
Document attributes in the request
Signed-off-by: David S. Miller <davem@davemloft.net>

The Marvell PHYs can measure the amplitude of the returned signal for
a given distance. Implement this option of the cable test
infrastructure. When reporting the step, convert the distance into cm.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>

v2:
Step based on the measurement resolution, and convert this to cm.
Signed-off-by: David S. Miller <davem@davemloft.net>

Add helpers for returning raw TDR helpers in netlink messages.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add the generic parts of the code used to trigger a cable test and
return raw TDR data. Any PHY driver which support this must implement
the new driver op.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>

v2
Update nxp-tja11xx for API change.
Signed-off-by: David S. Miller <davem@davemloft.net>

Some Ethernet PHYs can return the raw time domain reflectromatry data.
Add the attributes to allow this data to be requested and returned via
netlink ethtool.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>

v2:
m -> cm
Report what the PHY actually used for start/stop/step.
Signed-off-by: David S. Miller <davem@davemloft.net>

Fixed a ton of minor checkpatch errors/warnings and remove version
printing at module init/when device is found and use MODULE_VERSION
instead. Also modifying the RTL8029 PCI string to include the compatible
RTL8029AS nic.
The only mayor issue remaining is the missing SPDX tag, but since the
exact version of the GPL is not stated anywhere inside the file, its
impossible to add such a tag at the moment.
But maybe it is possible, since 8390.h states Donald Becker's 8390
drivers are licensed under GPL 2.2 only (= GPL-2.0-only ?).
The kernel module containing this patch compiles and runs without
problems on a RTL8029AS-based NE2000 clone card with kernel 5.7.0-rc6.
Signed-off-by: Armin Wolf <W_Armin@gmx.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

Ignore loopback-originatig packets soon enough and don't try to process L2
header where it doesn't exist. The very similar br_handle_frame() in bridge
code performs exactly the same check.

This is an example of such ICMPv6 packet:

skb len=96 headroom=40 headlen=96 tailroom=56
mac=(40,0) net=(40,40) trans=80
shinfo(txflags=0 nr_frags=0 gso(size=0 type=0 segs=0))
csum(0xae2e9a2f ip_summed=1 complete_sw=0 valid=0 level=0)
hash(0xc97ebd88 sw=1 l4=1) proto=0x86dd pkttype=5 iif=24
dev name=etha01.212 feat=0x0x0000000040005000
skb headroom: 00000000: 00 7c 86 52 84 88 ff ff 00 00 00 00 00 00 08 00
skb headroom: 00000010: 45 00 00 9e 5d 5c 40 00 40 11 33 33 00 00 00 01
skb headroom: 00000020: 02 40 43 80 00 00 86 dd
skb linear:   00000000: 60 09 88 bd 00 38 3a ff fe 80 00 00 00 00 00 00
skb linear:   00000010: 00 40 43 ff fe 80 00 00 ff 02 00 00 00 00 00 00
skb linear:   00000020: 00 00 00 00 00 00 00 01 86 00 61 00 40 00 00 2d
skb linear:   00000030: 00 00 00 00 00 00 00 00 03 04 40 e0 00 00 01 2c
skb linear:   00000040: 00 00 00 78 00 00 00 00 fd 5f 42 68 23 87 a8 81
skb linear:   00000050: 00 00 00 00 00 00 00 00 01 01 02 40 43 80 00 00
skb tailroom: 00000000: ...
skb tailroom: 00000010: ...
skb tailroom: 00000020: ...
skb tailroom: 00000030: ...

Call Trace, how it happens exactly:
 ...
 macvlan_handle_frame+0x321/0x425 [macvlan]
 ? macvlan_forward_source+0x110/0x110 [macvlan]
 __netif_receive_skb_core+0x545/0xda0
 ? enqueue_task_fair+0xe5/0x8e0
 ? __netif_receive_skb_one_core+0x36/0x70
 __netif_receive_skb_one_core+0x36/0x70
 process_backlog+0x97/0x140
 net_rx_action+0x1eb/0x350
 ? __hrtimer_run_queues+0x136/0x2e0
 __do_softirq+0xe3/0x383
 do_softirq_own_stack+0x2a/0x40
 </IRQ>
 do_softirq.part.4+0x4e/0x50
 netif_rx_ni+0x60/0xd0
 dev_loopback_xmit+0x83/0xf0
 ip6_finish_output2+0x575/0x590 [ipv6]
 ? ip6_cork_release.isra.1+0x64/0x90 [ipv6]
 ? __ip6_make_skb+0x38d/0x680 [ipv6]
 ? ip6_output+0x6c/0x140 [ipv6]
 ip6_output+0x6c/0x140 [ipv6]
 ip6_send_skb+0x1e/0x60 [ipv6]
 rawv6_sendmsg+0xc4b/0xe10 [ipv6]
 ? proc_put_long+0xd0/0xd0
 ? rw_copy_check_uvector+0x4e/0x110
 ? sock_sendmsg+0x36/0x40
 sock_sendmsg+0x36/0x40
 ___sys_sendmsg+0x2b6/0x2d0
 ? proc_dointvec+0x23/0x30
 ? addrconf_sysctl_forward+0x8d/0x250 [ipv6]
 ? dev_forward_change+0x130/0x130 [ipv6]
 ? _raw_spin_unlock+0x12/0x30
 ? proc_sys_call_handler.isra.14+0x9f/0x110
 ? __call_rcu+0x213/0x510
 ? get_max_files+0x10/0x10
 ? trace_hardirqs_on+0x2c/0xe0
 ? __sys_sendmsg+0x63/0xa0
 __sys_sendmsg+0x63/0xa0
 do_syscall_64+0x6c/0x1e0
 entry_SYSCALL_64_after_hwframe+0x49/0xbe
Signed-off-by: Alexander Sverdlin <alexander.sverdlin@nokia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Ido Schimmel says:

====================
mlxsw: Various trap changes - part 2

This patch set contains another set of small changes in mlxsw trap
configuration. It is the last set before exposing control traps (e.g.,
IGMP query, ARP request) via devlink-trap.

Tested with existing devlink-trap selftests. Please see individual
patches for a detailed changelog.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

The device has a trap for IPv6 packets that need be routed and have a
unicast link-local destination IP (i.e., fe80::/10). This allows mlxsw
to ignore link-local routes, as the packets will be trapped to the CPU
in any case.

However, since link-local routes are not programmed, it is possible for
routed packets to hit the default route which might also be programmed
to trap packets. This means that packets with a link-local destination
IP might be trapped for the wrong reason.

To overcome this, allow programming link-local prefix routes (usually
one fe80::/64 per-table), so that the packets will be forwarded until
reaching the link-local trap.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Bidirectional Forwarding Detection (BFD) provides "low-overhead,
short-duration detection of failures in the path between adjacent
forwarding engines" (RFC 5880).

This is accomplished by exchanging BFD packets between the two
forwarding engines. Up until now these packets were trapped via the
general local delivery (i.e., IP2ME) trap which also traps a lot of
other packets that are not as time-sensitive as BFD packets.

Expose dedicated traps for BFD packets so that user space could
configure a dedicated policer for them.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

IPv6 packets that need to be forwarded and have a link-local source IP are
dropped by the kernel and an ICMPv6 "Destination unreachable" is sent to
the sending host.

As such, change the trap group of such packets so that they do not
interfere with IPv6 management packets. In the future this trap will be
exposed as an exception via devlink-trap.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Routed IP packets with the Router Alert option need to be trapped to
the CPU as they might need to be locally delivered to raw sockets with
the IP_ROUTER_ALERT / IPV6_ROUTER_ALERT socket option.

Move them to the same group with other packets that might need to be
trapped following route lookup.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

After the previous patch the split is no longer necessary and all the
trap groups can be moved under the same enum.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

As explained in commit e6125230 ("mlxsw: spectrum_trap: Introduce
dummy group with thin policer"), the purpose of the "thin" policer is to
pass as less packets as possible to the CPU.

The identifier of this policer is currently set according to the maximum
number of used trap groups, but this is fragile: On Spectrum-1 the
maximum number of policers is less than the maximum number of trap
groups, which might result in an invalid policer identifier in case the
number of used trap groups grows beyond the policer limit.

Solve this by dynamically allocating the policer identifier.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The number of Spectrum trap groups is not infinite, but two identifiers
are occupied by SwitchX-2 specific trap groups. Free these identifiers
by moving them out of the main enum.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

To align with recent recommended values. Will be configurable by future
patches.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Packets with an IPv6 link-local destination (i.e., fe80::/10) should not
be forwarded and are therefore trapped to the CPU for local delivery.
Since these packets are trapped for the same logical reason as packets
hitting local routes, associate both traps with the same group.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When a packet enters the device it is classified to a filtering
identifier (FID) based on the ingress port and VLAN. The FID miss trap
is used to trap packets for which a FID could not be found.

In mlxsw this trap should only be triggered when a port is enslaved to
an OVS bridge and a matching ACL rule could not be found, so as to
trigger learning.

These packets are therefore completely unrelated to packets hitting
local routes and should be in a different group. Move them.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Group these various IPv6 packets (e.g., router solicitations, router
advertisement) together and subject them to the same policer.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The IPv6 Neighbour Discovery (ND) group will be used for various IPv6
packets, not all of which fall under the definition of ND, so rename it
to "IPV6" which is more appropriate.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Trap groups that use the same policer settings can share the same switch
case.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>