So updated vblank-rework pull request, now with the polish that Mario
requested applied (and reviewed by him). Also with backmerge like you've
requested for easier merging.

The neat thing this finally allows is to immediately disable the vblank
interrupt on the last drm_vblank_put if the hardware has perfectly
accurate vblank counter and timestamp readout support. On i915 that
required piles of small adjustements from Ville since depending upon the
platform and port the vblank happens at different scanout lines.

Of course this is fully opt-in and per-device (we need that since gen2
doesn't have a hw vblank counter).

* tag 'topic/vblank-rework-2014-09-12' of git://anongit.freedesktop.org/drm-intel: (22 commits)
  drm: Clarify vblank ts/scanoutpos sampling #defines
  drm: Simplify return value of drm_get_last_vbltimestamp
  drm: Only update final vblank count when precise ts is available
  drm: Really never disable vblank irqs for offdelay==0
  drm: Use vblank_disable_and_save in drm_vblank_cleanup()
  drm: Remove drm_vblank_cleanup from drm_vblank_init error path.
  drm: Store the vblank timestamp when adjusting the counter during disable
  drm: Fix confusing debug message in drm_update_vblank_count()
  drm/i915: Update scanline_offset only for active crtcs
  drm: Kick start vblank interrupts at drm_vblank_on()
  drm/i915: Opt out of vblank disable timer on >gen2
  drm: Add dev->vblank_disable_immediate flag
  drm: Disable vblank interrupt immediately when drm_vblank_offdelay<0
  drm: Fix race between drm_vblank_off() and drm_queue_vblank_event()
  drm: Fix deadlock between event_lock and vbl_lock/vblank_time_lock
  drm: Reduce the amount of dev->vblank[crtc] in the code
  drm: Avoid random vblank counter jumps if the hardware counter has been reset
  drm: Have the vblank counter account for the time between vblank irq disable and drm_vblank_off()
  drm: Move drm_update_vblank_count()
  drm: Don't clear vblank timestamps when vblank interrupt is disabled
  ...

This fixes problems on ppc64 platforms, where we could end up using
a WC mapping for migrating BOs with memcpy, when really we want to
use cached memory.
Tested-by: Ben Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>

Just move this into a separate header file, and make the
two users use it.
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>

concurrent buffer reads.

* 'drm-next-3.18' of git://people.freedesktop.org/~agd5f/linux:
  drm/radeon: allow concurrent buffer reads
  drm/radeon: add the infrastructure for concurrent buffer access
  drm/ttm: allow fence to be added as shared

The userspace drm.h include doesn't prefix the drm directory.  This can lead
to compile failures as /usr/include/drm/ isn't in the standard gcc include
paths.  Fix it to be <drm/drm.h>, which matches the rest of the driver drm
header files that get installed into /usr/include/drm.

Red Hat Bugzilla: https://bugzilla.redhat.com/show_bug.cgi?id=1138759

Fixes: 1d7a5cbfReported-by: Jeffrey Bastian <jbastian@redhat.com>
Signed-off-by: Josh Boyer <jwboyer@fedoraproject.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>

Signed-off-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

This allows us to specify if we want to sync to
the shared fences of a reservation object or not.
Signed-off-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

This patch adds a new flag to the ttm_validate_buffer list to
add the fence as shared to the reservation object.
Signed-off-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Dave asked me to do the backmerge before sending him the revised pull
request, so here we go. Nothing fancy in the conflicts, just a few
things changed right next to each another.

Conflicts:
	drivers/gpu/drm/drm_irq.c
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>

I've read INVBL as "invalid backlight" and got mightly confused.
The #defines are already fairly long and we can afford to extend
them a bit more without resulting in ugly code all over.

I'm not sure how useful the complicated bitmask return value of these
functions really are since no one checks them. But for now let's keep
things as is.

Cc: Mario Kleiner <mario.kleiner.de@gmail.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Mario Kleiner <mario.kleiner.de@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

Imo u32 hints at a register value, but in reality all callers only
care whether the sampled timestamp is precise or not. So give them
just a bool.

Also move the declaration out of drmP.h, it's only used in drm_irq.c.

v2: Also drop the EXPORT_SYMBOL, spotted by Mario.

Cc: Mario Kleiner <mario.kleiner.de@gmail.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Mario Kleiner <mario.kleiner.de@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>

Drivers without a hardware vblank counter simply can't account for the
vblanks that happened while the vblank interrupt was off. To check
this grab a vblank timestamp and if the result is dubious follow the
normal save-and-disable logic.

Drivers should prevent this by setting vblank_disable_allowed = false,
but since running vblank interrupts constantly is not good for power
consumption most drivers lie. Testing for precise vblank timestamps is
the next best thing we can check for.
Suggested-by: Mario Kleiner <mario.kleiner.de@gmail.com>
Cc: Mario Kleiner <mario.kleiner.de@gmail.com>
Cc: Matt Roper <matthew.d.roper@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Mario Kleiner <mario.kleiner.de@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>

With the new support for immediate vblank disabling we always disabled
the vblank interrupt right away, irrespective of the vblank offdelay
setting.

But being able to let vblanks run forever is fairly useful for
debugging, so restore that behaviour.
Suggested-by: Mario Kleiner <mario.kleiner.de@gmail.com>
Cc: Mario Kleiner <mario.kleiner.de@gmail.com>
Cc: Matt Roper <matthew.d.roper@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Mario Kleiner <mario.kleiner.de@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>

 1) add LVDS support for mdp4 (tested with auo B101XTN01.0 panel)
 2) add B101XTN01.0 panel
 3) bit of gpu refactoring to prepare for addition of addition gpu
generations beyond just a3xx

* 'msm-next' of git://people.freedesktop.org/~robclark/linux:
  drm/msm/adreno: push dump/show stuff to base class
  drm/msm/adreno: bit of init refactoring
  drm/msm/adreno: move decision about what gpu to to load
  drm/msm/adreno: split adreno device out into it's own file
  drm/panel/simple: add optronics B101XTN01.0 (v3)
  drm/msm/mdp4: add LVDS panel support
  drm/msm/mdp4: fix blend setup with multiple crtcs
  drm/msm: update generated headers

A few more radeon patches for 3.18.  This patch set gives us more
flexibility with respect to buffer placement in vram with respect
to CPU access.  E.g., if you know you will not need CPU access, we can
now pin outside of the CPU window, reducing contention for the
CPU window space.

* 'drm-next-3.18' of git://people.freedesktop.org/~agd5f/linux:
  drm/radeon: add RADEON_GEM_NO_CPU_ACCESS BO creation flag (v4)
  drm/radeon: Clean up assignment of TTM placement lpfn member for pinning
  drm/radeon: Add RADEON_GEM_CPU_ACCESS BO creation flag

Allows pinning of buffers in the non-CPU visible portion of
vram.

v2: incorporate Michel's comments.
v3: rebase on Michel's patch
v4: rebase on Michel's v2 patch
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Michel Dänzer <michel.daenzer@amd.com>

This sets the lpfn member to 0 instead of the full domain size. TTM uses
the full domain size when lpfn is 0.
Signed-off-by: Michel Dänzer <michel.daenzer@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

This flag is a hint that userspace expects the BO to be accessed by the
CPU. We can use that hint to prevent such BOs from ever being stored in
the CPU inaccessible part of VRAM.
Signed-off-by: Michel Dänzer <michel.daenzer@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Add ptr to list of interesting registers to 'struct adreno_gpu' and use
that to move most of the debugfs show and register dump bits down into
adreno_gpu.  This will avoid duplication as support for additional
adreno generations is added.
Signed-off-by: Rob Clark <robdclark@gmail.com>

Push a few bits down into adreno_gpu so they won't have to be duplicated
as support for additional adreno generations is added.
Signed-off-by: Rob Clark <robdclark@gmail.com>

Move this into into adreno_device, and decide based on gpu revision
rather than just assuming a3xx.
Signed-off-by: Rob Clark <robdclark@gmail.com>

We'd rather not duplicate these parts as support for additional gpu
generations is added.
Signed-off-by: Rob Clark <robdclark@gmail.com>

LVDS panel, make/model described as:

AU Optronics Corporation - B101XTN01.0 (H/W:0A)

See:
http://www.encore-electronic.com/media/B101XTN01.0.pdf

Tested with panel attached to an Inforce IFC6410 board.
Signed-off-by: Rob Clark <robdclark@gmail.com>

LVDS panel support uses the LCDC (parallel) encoder.  Unlike with HDMI,
there is not a separate LVDS block, so no need to split things into a
bridge+connector.  Nor is there is anything re-used with mdp5.

Note that there can be some regulators shared between HDMI and LVDS (in
particular, on apq8064, ext_3v3p), so we should not use the _exclusive()
variants of devm_regulator_get().

The drm_panel framework is used for panel-specific driver.
Signed-off-by: Rob Clark <robdclark@gmail.com>

In particular, blend_setup() should not overwrite the other crtc's mixer
settings.  Also, the encoder needs to be able to specify the mixer-id
explicitly, since both LVDS and DTV use 'INTF_LVDC_DTV', so we cannot
guess the mixer-id from the interface.
Signed-off-by: Rob Clark <robdclark@gmail.com>

In particular, pick up the definitions for a handful of LVDS related
registers.
Signed-off-by: Rob Clark <robdclark@gmail.com>

IPUv3 preparations for capture support

* tag 'ipu-3.18' of git://git.pengutronix.de/git/pza/linux: (26 commits)
  gpu: ipu-v3: Add ipu_dump()
  gpu: ipu-cpmem: Add ipu_cpmem_dump()
  gpu: ipu-v3: Add more planar formats support
  gpu: ipu-cpmem: Add second buffer support to ipu_cpmem_set_image()
  gpu: ipu-cpmem: Add ipu_cpmem_set_rotation()
  gpu: ipu-cpmem: Add ipu_cpmem_set_axi_id()
  gpu: ipu-cpmem: Add ipu_cpmem_set_block_mode()
  gpu: ipu-v3: Add ipu_idmac_lock_enable()
  gpu: ipu-v3: Add ipu_idmac_enable_watermark()
  gpu: ipu-v3: Add ipu_stride_to_bytes()
  gpu: ipu-v3: Add __ipu_idmac_reset_current_buffer()
  gpu: ipu-v3: Add ipu_idmac_clear_buffer()
  gpu: ipu-v3: Add ipu_idmac_buffer_is_ready()
  gpu: ipu-v3: Move IDMAC channel names to imx-ipu-v3.h
  gpu: ipu-v3: Add helper function checking if pixfmt is planar
  gpu: ipu-v3: Add rotation mode conversion utilities
  gpu: ipu-v3: Add ipu_mbus_code_to_colorspace()
  gpu: ipu-v3: smfc: Add ipu_smfc_set_watermark()
  gpu: ipu-v3: smfc: Convert to per-channel
  gpu: ipu-v3: smfc: Move enable/disable to ipu-smfc.c
  ...

Same as the other legacy APIs, most of this is internal, so prefix it with
drm_legacy_* and move into drm_legacy.h.
Signed-off-by: David Herrmann <dh.herrmann@gmail.com>
Reviewed-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>

This merges all the remains of drm_usb into its only user, udl. We can
then drop all the drm_usb stuff, including dev->usbdev.
Signed-off-by: David Herrmann <dh.herrmann@gmail.com>
Reviewed-by: Thierry Reding <treding@nvidia.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Dave Airlie <airlied@redhat.com>

..we will not miss you..
Signed-off-by: David Herrmann <dh.herrmann@gmail.com>
Reviewed-by: Thierry Reding <treding@nvidia.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Dave Airlie <airlied@redhat.com>

One step closer to dropping all the drm_bus_* code:
Add a driver->set_busid() callback and make all drivers use the generic
helpers. Nouveau is the only driver that uses two different bus-types with
the same drm_driver. This is totally broken if both buses are available on
the same machine (unlikely, but lets be safe). Therefore, we create two
different drivers for each platform during module_init() and set the
set_busid() callback respectively.
Signed-off-by: David Herrmann <dh.herrmann@gmail.com>
Reviewed-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>

This field is unused and there is really no reason to optimize
unique-allocations. Drop it.
Signed-off-by: David Herrmann <dh.herrmann@gmail.com>
Reviewed-by: Thierry Reding <treding@nvidia.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Dave Airlie <airlied@redhat.com>

Lets use kasprintf() to avoid pre-allocating the buffer. This is really
nothing to optimize for speed and the input is trusted, so kasprintf() is
just fine.
Signed-off-by: David Herrmann <dh.herrmann@gmail.com>
Reviewed-by: Thierry Reding <treding@nvidia.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Dave Airlie <airlied@redhat.com>

Including headers somewhere else but at the top is ugly, deprecated and
was used in early days only to speed up compile-times. Those days are
over. Make headers independent and then move the inclusions to the top.
Signed-off-by: David Herrmann <dh.herrmann@gmail.com>
Reviewed-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>

The sigdata structure is only used to group two fields in drm_device.
Inline it and make it an unnamed object.
Signed-off-by: David Herrmann <dh.herrmann@gmail.com>
Reviewed-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>

Calling vblank_disable_fn() will cause that function to no-op
if !dev->vblank_disable_allowed for some kms drivers, e.g.,
on nouveau-kms. This can cause the gpu vblank irq's to not get
disabled before freeing the dev->vblank array, so if a
vblank irq fires and calls into drm_handle_vblank() after
drm_vblank_cleanup() completes, it will cause use-after-free
access to dev->vblank array.

Call vblank_disable_and_save unconditionally, so vblank irqs
are guaranteed to be off, before we delete the data structures
on which they operate.
Signed-off-by: Mario Kleiner <mario.kleiner.de@gmail.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
[danvet: Fix subsystem name in patch subject.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

DRM_DEBUG_CODE is currently always set, so distributions enable it. The
only reason to keep support in code is if developers wanted to disable
debug support. Sounds unlikely.

All the DRM_DEBUG() printks are still guarded by a drm_debug read. So if
its cacheline is read once, they're discarded pretty fast.. There should
hardly be any performance penalty, it's even guarded by unlikely().
Signed-off-by: David Herrmann <dh.herrmann@gmail.com>
Reviewed-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>

It is hardly possible to review the drmP.h includes, anymore. Order them
alphabetically, linux/ first, then asm/ and then local drm/ includes.

Since a long time ago, kernel headers have been converted to include
required headers themselves. No-one cares whether that means the compiler
has to include a header multiple times. In fact, GCC already does some
optimization regarding multiple inclusions if a sorrounding #ifndef is
present.
Signed-off-by: David Herrmann <dh.herrmann@gmail.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>

With drm_memory.h gone, there is no header left that uses __OS_HAS_AGP.
Move it into drm_agpsupport.h (which is itself included from drmP.h) to
hide it harder from public eyes.
Signed-off-by: David Herrmann <dh.herrmann@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>

The drm_memory.h header is only used to define PAGE_AGP, which is only
used in drm_memory.c. Fold the header into drm_memory.c and drop it.
Signed-off-by: David Herrmann <dh.herrmann@gmail.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Dave Airlie <airlied@redhat.com>