Skip to content

L
linux
Switch branch/tag
  1. 07 Nov, 2016 5 commits
    • Noralf Trønnes's avatar
      i2c: bcm2835: Add support for Repeated Start Condition · ee05fea2
      Noralf Trønnes authored 
      Documentation/i2c/i2c-protocol states that Combined transactions should
separate messages with a Start bit and end the whole transaction with a
Stop bit. This patch adds support for issuing only a Start between
messages instead of a Stop followed by a Start.

This implementation differs from downstream i2c-bcm2708 in 2 respects:
- it uses an interrupt to detect that the transfer is active instead
  of using polling. There is no interrupt for Transfer Active, but by
  not prefilling the FIFO it's possible to use the TXW interrupt.
- when resetting/disabling the controller between transfers it writes
  CLEAR to the control register instead of just zero.
  Using just zero gave many errors. This might be the reason why
  downstream had to disable this feature and make it available with a
  module parameter.

I have run thousands of transfers to a DS1307 (rtc), MMA8451 (accel)
and AT24C32 (eeprom) in parallel without problems.
Signed-off-by: default avatarNoralf Trønnes <noralf@tronnes.org>
Acked-by: default avatarEric Anholt <eric@anholt.net>
Signed-off-by: default avatarWolfram Sang <wsa@the-dreams.de>
      ee05fea2
    • Noralf Trønnes's avatar
      i2c: bcm2835: Can't support I2C_M_IGNORE_NAK · 8d2cc5cc
      Noralf Trønnes authored 
      The controller can't support this flag, so remove it.

Documentation/i2c/i2c-protocol states that all of the message is sent:

I2C_M_IGNORE_NAK:
    Normally message is interrupted immediately if there is [NA] from the
    client. Setting this flag treats any [NA] as [A], and all of
    message is sent.

>From the BCM2835 ARM Peripherals datasheet:

    The ERR field is set when the slave fails to acknowledge either
    its address or a data byte written to it.

So when the controller doesn't receive an ack, it sets ERR and raises
an interrupt. In other words, the whole message is not sent.
Signed-off-by: default avatarNoralf Trønnes <noralf@tronnes.org>
Reviewed-by: default avatarEric Anholt <eric@anholt.net>
Signed-off-by: default avatarWolfram Sang <wsa@the-dreams.de>
      8d2cc5cc
    • Noralf Trønnes's avatar
      i2c: bcm2835: Use dev_dbg logging on transfer errors · 23c9540b
      Noralf Trønnes authored 
      Writing to an AT24C32 generates on average 2x i2c transfer errors per
32-byte page write. Which amounts to a lot for a 4k write. This is due
to the fact that the chip doesn't respond during it's internal write
cycle when the at24 driver tries and retries the next write.
Only a handful drivers use dev_err() on transfer error, so switch to
dev_dbg() instead.
Signed-off-by: default avatarNoralf Trønnes <noralf@tronnes.org>
Reviewed-by: default avatarEric Anholt <eric@anholt.net>
Signed-off-by: default avatarWolfram Sang <wsa@the-dreams.de>
      23c9540b
    • Noralf Trønnes's avatar
      i2c: bcm2835: Protect against unexpected TXW/RXR interrupts · d4030d75
      Noralf Trønnes authored 
      If an unexpected TXW or RXR interrupt occurs (msg_buf_remaining == 0),
the driver has no way to fill/drain the FIFO to stop the interrupts.
In this case the controller has to be disabled and the transfer
completed to avoid hang.

(CLKT | ERR) and DONE interrupts are completed in their own paths, and
the controller is disabled in the transfer function after completion.
Unite the code paths and do disabling inside the interrupt routine.

Clear interrupt status bits in the united completion path instead of
trying to do it on every interrupt which isn't necessary.
Only CLKT, ERR and DONE can be cleared that way.

Add the status value to the error value in case of TXW/RXR errors to
distinguish them from the other S_LEN error.
Signed-off-by: default avatarNoralf Trønnes <noralf@tronnes.org>
Reviewed-by: default avatarEric Anholt <eric@anholt.net>
Signed-off-by: default avatarWolfram Sang <wsa@the-dreams.de>
      d4030d75
    • Noralf Trønnes's avatar
      i2c: bcm2835: Fix hang for writing messages larger than 16 bytes · e2474541
      Noralf Trønnes authored 
      Writing messages larger than the FIFO size results in a hang, rendering
the machine unusable. This is because the RXD status flag is set on the
first interrupt which results in bcm2835_drain_rxfifo() stealing bytes
from the buffer. The controller continues to trigger interrupts waiting
for the missing bytes, but bcm2835_fill_txfifo() has none to give.
In this situation wait_for_completion_timeout() apparently is unable to
stop the madness.

The BCM2835 ARM Peripherals datasheet has this to say about the flags:
  TXD: is set when the FIFO has space for at least one byte of data.
  RXD: is set when the FIFO contains at least one byte of data.
  TXW: is set during a write transfer and the FIFO is less than full.
  RXR: is set during a read transfer and the FIFO is or more full.

Implementing the logic from the downstream i2c-bcm2708 driver solved
the hang problem.
Signed-off-by: default avatarNoralf Trønnes <noralf@tronnes.org>
Reviewed-by: default avatarEric Anholt <eric@anholt.net>
Reviewed-by: default avatarMartin Sperl <kernel@martin.sperl.org>
Signed-off-by: default avatarWolfram Sang <wsa@the-dreams.de>
      e2474541
  3. 05 Nov, 2016 15 commits
  5. 04 Nov, 2016 16 commits
    • Linus Torvalds's avatar
      Merge tag 'drm-fixes-for-v4.9-rc4' of git://people.freedesktop.org/~airlied/linux · d4c5f43d
      Linus Torvalds authored 
      Pull drm fixes from Dave Airlie:
 "Fixes for amdgpu, radeon, intel, imx and virtio-gpu.

  This is a bit larger than I'd like, but I had some stuff I meant to
  send for -rc3 but was waiting for the PAT regression fix to land. So
  this is really fixes for rc3 and rc4 in one go.

  There are a set of fixes for an oops we've been seeing around MST
  display unplug, along with more suspend/resume and shutdown fixes for
  amdgpu, one power management follow on fix for nouveau, and set of imx
  fixes, and a single virtio-gpu regression fix"

* tag 'drm-fixes-for-v4.9-rc4' of git://people.freedesktop.org/~airlied/linux: (54 commits)
  virtio-gpu: fix vblank events
  drm/nouveau/acpi: fix check for power resources support
  drm/i915: Fix SKL+ 90/270 degree rotated plane coordinate computation
  drm/i915: Remove two invalid warns
  drm/i915: Rotated view does not need a fence
  drm/i915/fbc: fix CFB size calculation for gen8+
  drm: i915: Wait for fences on new fb, not old
  drm/i915: Clean up DDI DDC/AUX CH sanitation
  drm/i915: Respect alternate_aux_channel for all DDI ports
  drm/i915/gen9: fix watermarks when using the pipe scaler
  drm/i915: Fix mismatched INIT power domain disabling during suspend
  drm/i915: fix a read size argument
  drm/i915: Use fence_write() from rpm resume
  drm/i915/gen9: fix DDB partitioning for multi-screen cases
  drm/i915: workaround sparse warning on variable length arrays
  drm/i915: keep declarations in i915_drv.h
  drm/amd/powerplay: fix bug get wrong evv voltage of Polaris.
  drm/amdgpu/si_dpm: workaround for SI kickers
  drm/radeon/si_dpm: workaround for SI kickers
  drm/amdgpu: fix s3 resume back, uvd dpm randomly can't disable.
  ...
      d4c5f43d
    • Niklas Cassel's avatar
      PCI: designware: Check for iATU unroll support after initializing host · 416379f9
      Niklas Cassel authored 
      dw_pcie_iatu_unroll_enabled() reads a dbi_base register.  Reading any
dbi_base register before pp->ops->host_init has been called causes
"imprecise external abort" on platforms like ARTPEC-6, where the PCIe
module is disabled at boot and first enabled in pp->ops->host_init.  Move
dw_pcie_iatu_unroll_enabled() to dw_pcie_setup_rc(), since it is after
pp->ops->host_init, but before pp->iatu_unroll_enabled is actually used.

Fixes: a0601a47 ("PCI: designware: Add iATU Unroll feature")
Tested-by: default avatarJames Le Cuirot <chewi@gentoo.org>
Signed-off-by: default avatarNiklas Cassel <niklas.cassel@axis.com>
Signed-off-by: default avatarBjorn Helgaas <bhelgaas@google.com>
Acked-by: default avatarJoao Pinto <jpinto@synopsys.com>
Acked-by: default avatarOlof Johansson <olof@lixom.net>
      416379f9
    • Linus Torvalds's avatar
      Merge tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm · 66cecb67
      Linus Torvalds authored 
      Pull KVM updates from Paolo Bonzini:
 "One NULL pointer dereference, and two fixes for regressions introduced
  during the merge window.

  The rest are fixes for MIPS, s390 and nested VMX"

* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
  kvm: x86: Check memopp before dereference (CVE-2016-8630)
  kvm: nVMX: VMCLEAR an active shadow VMCS after last use
  KVM: x86: drop TSC offsetting kvm_x86_ops to fix KVM_GET/SET_CLOCK
  KVM: x86: fix wbinvd_dirty_mask use-after-free
  kvm/x86: Show WRMSR data is in hex
  kvm: nVMX: Fix kernel panics induced by illegal INVEPT/INVVPID types
  KVM: document lock orders
  KVM: fix OOPS on flush_work
  KVM: s390: Fix STHYI buffer alignment for diag224
  KVM: MIPS: Precalculate MMIO load resume PC
  KVM: MIPS: Make ERET handle ERL before EXL
  KVM: MIPS: Fix lazy user ASID regenerate for SMP
      66cecb67
    • Linus Torvalds's avatar
      Merge branch 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus · 34c510b2
      Linus Torvalds authored 
      Pull MIPS fixes from Ralf Baechle:
 "A set of MIPS fixes for 4.9:

   - lots of fixes for printk continuations
   - six fixes for FP related code.
   - fix max_low_pfn with disabled highmem
   - fix KASLR handling of NULL FDT and KASLR for generic kernels
   - fix build of compressed image
   - provide default mips_cpc_default_phys_base to ignore CPC
   - fix reboot on Malta"

* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus:
  MIPS: Fix max_low_pfn with disabled highmem
  MIPS: Correct MIPS I FP sigcontext layout
  MIPS: Fix ISA I/II FP signal context offsets
  MIPS: Remove FIR from ISA I FP signal context
  MIPS: Fix ISA I FP sigcontext access violation handling
  MIPS: Fix FCSR Cause bit handling for correct SIGFPE issue
  MIPS: ptrace: Also initialize the FP context on individual FCSR writes
  MIPS: dump_tlb: Fix printk continuations
  MIPS: Fix __show_regs() output
  MIPS: traps: Fix output of show_code
  MIPS: traps: Fix output of show_stacktrace
  MIPS: traps: Fix output of show_backtrace
  MIPS: Fix build of compressed image
  MIPS: generic: Fix KASLR for generic kernel.
  MIPS: KASLR: Fix handling of NULL FDT
  MIPS: Malta: Fixup reboot
  MIPS: CPC: Provide default mips_cpc_default_phys_base to ignore CPC
      34c510b2
    • Linus Torvalds's avatar
      Merge branch 'parisc-4.9-3' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux · f7df76e6
      Linus Torvalds authored 
      Pull parisc updates from Helge Deller:
 "The first three patches are trivial and add some required KERN_CONT,
  ignore the new pkey syscalls on parisc and use the LINUX_GATEWAY_ADDR
  define instead of hardcoded values.

  The two patches from Dave Anglin are important.

  The first one avoids trashing the sr2 and sr3 space registers in the
  Light-weight syscall path. Especially the usage of sr3 is critical
  since it may get trashed by the interrupt handler.

  The second patch is even more important and tagged for stable series.
  It protects one critical section in the syscall entry path by
  disabling local interrupts. Without disabling interrupts, the sr7
  space register may not be in sync with the current stack setup and
  thus an incoming hardware interrupt may destroy memory in random
  userspace areas"

* 'parisc-4.9-3' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux:
  parisc: Ignore the pkey system calls for now
  parisc: Use LINUX_GATEWAY_ADDR define instead of hardcoded value
  parisc: Ensure consistent state when switching to kernel stack at syscall entry
  parisc: Avoid trashing sr2 and sr3 in LWS code
  parisc: use KERN_CONT when printing device inventory
      f7df76e6
    • Vladimir Zapolskiy's avatar
      i2c: core: fix NULL pointer dereference under race condition · 147b36d5
      Vladimir Zapolskiy authored 
      Race condition between registering an I2C device driver and
deregistering an I2C adapter device which is assumed to manage that
I2C device may lead to a NULL pointer dereference due to the
uninitialized list head of driver clients.

The root cause of the issue is that the I2C bus may know about the
registered device driver and thus it is matched by bus_for_each_drv(),
but the list of clients is not initialized and commonly it is NULL,
because I2C device drivers define struct i2c_driver as static and
clients field is expected to be initialized by I2C core:

  i2c_register_driver()             i2c_del_adapter()
    driver_register()                 ...
      bus_add_driver()                ...
        ...                           bus_for_each_drv(..., __process_removed_adapter)
      ...                               i2c_do_del_adapter()
    ...                                   list_for_each_entry_safe(..., &driver->clients, ...)
    INIT_LIST_HEAD(&driver->clients);

To solve the problem it is sufficient to do clients list head
initialization before calling driver_register().

The problem was found while using an I2C device driver with a sluggish
registration routine on a bus provided by a physically detachable I2C
master controller, but practically the oops may be reproduced under
the race between arbitraty I2C device driver registration and managing
I2C bus device removal e.g. by unbinding the latter over sysfs:

% echo 21a4000.i2c > /sys/bus/platform/drivers/imx-i2c/unbind
  Unable to handle kernel NULL pointer dereference at virtual address 00000000
  Internal error: Oops: 17 [#1] SMP ARM
  CPU: 2 PID: 533 Comm: sh Not tainted 4.9.0-rc3+ #61
  Hardware name: Freescale i.MX6 Quad/DualLite (Device Tree)
  task: e5ada400 task.stack: e4936000
  PC is at i2c_do_del_adapter+0x20/0xcc
  LR is at __process_removed_adapter+0x14/0x1c
  Flags: NzCv  IRQs on  FIQs on  Mode SVC_32  ISA ARM  Segment none
  Control: 10c5387d  Table: 35bd004a  DAC: 00000051
  Process sh (pid: 533, stack limit = 0xe4936210)
  Stack: (0xe4937d28 to 0xe4938000)
  Backtrace:
  [<c0667be0>] (i2c_do_del_adapter) from [<c0667cc0>] (__process_removed_adapter+0x14/0x1c)
  [<c0667cac>] (__process_removed_adapter) from [<c0516998>] (bus_for_each_drv+0x6c/0xa0)
  [<c051692c>] (bus_for_each_drv) from [<c06685ec>] (i2c_del_adapter+0xbc/0x284)
  [<c0668530>] (i2c_del_adapter) from [<bf0110ec>] (i2c_imx_remove+0x44/0x164 [i2c_imx])
  [<bf0110a8>] (i2c_imx_remove [i2c_imx]) from [<c051a838>] (platform_drv_remove+0x2c/0x44)
  [<c051a80c>] (platform_drv_remove) from [<c05183d8>] (__device_release_driver+0x90/0x12c)
  [<c0518348>] (__device_release_driver) from [<c051849c>] (device_release_driver+0x28/0x34)
  [<c0518474>] (device_release_driver) from [<c0517150>] (unbind_store+0x80/0x104)
  [<c05170d0>] (unbind_store) from [<c0516520>] (drv_attr_store+0x28/0x34)
  [<c05164f8>] (drv_attr_store) from [<c0298acc>] (sysfs_kf_write+0x50/0x54)
  [<c0298a7c>] (sysfs_kf_write) from [<c029801c>] (kernfs_fop_write+0x100/0x214)
  [<c0297f1c>] (kernfs_fop_write) from [<c0220130>] (__vfs_write+0x34/0x120)
  [<c02200fc>] (__vfs_write) from [<c0221088>] (vfs_write+0xa8/0x170)
  [<c0220fe0>] (vfs_write) from [<c0221e74>] (SyS_write+0x4c/0xa8)
  [<c0221e28>] (SyS_write) from [<c0108a20>] (ret_fast_syscall+0x0/0x1c)
Signed-off-by: default avatarVladimir Zapolskiy <vladimir_zapolskiy@mentor.com>
Signed-off-by: default avatarWolfram Sang <wsa@the-dreams.de>
Cc: stable@kernel.org
      147b36d5
    • James Hogan's avatar
      MIPS: Fix max_low_pfn with disabled highmem · 16a767ec
      James Hogan authored 
      When low memory doesn't reach HIGHMEM_START (e.g. up to 256MB at PA=0 is
common) and highmem is present above HIGHMEM_START (e.g. on Malta the
RAM overlayed by the IO region is aliased at PA=0x90000000), max_low_pfn
will be initially calculated very large and then clipped down to
HIGHMEM_START.

This causes crashes when reading /sys/kernel/mm/page_idle/bitmap
(i.e. CONFIG_IDLE_PAGE_TRACKING=y) when highmem is disabled. pfn_valid()
will compare against max_mapnr which is derived from max_low_pfn when
there is no highend_pfn set up, and will return true for PFNs right up
to HIGHMEM_START, even though they are beyond the end of low memory and
no page structs will actually exist for these PFNs.

This is fixed by skipping high memory regions when initially calculating
max_low_pfn if highmem is disabled, so it doesn't get clipped too high.
We also clip regions which overlap the highmem boundary when highmem is
disabled, so that max_pfn doesn't extend into highmem either.
Signed-off-by: default avatarJames Hogan <james.hogan@imgtec.com>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/14490/Signed-off-by: default avatarRalf Baechle <ralf@linux-mips.org>
      16a767ec
    • Maciej W. Rozycki's avatar
      MIPS: Correct MIPS I FP sigcontext layout · f92722dc
      Maciej W. Rozycki authored 
      Complement commit 80cbfad7 ("MIPS: Correct MIPS I FP context
layout") and correct the way Floating Point General registers are stored
in a signal context with MIPS I hardware.

Use the S.D and L.D assembly macros to have pairs of SWC1 instructions
and pairs of LWC1 instructions produced, respectively, in an arrangement
which makes the memory representation of floating-point data passed
compatible with that used by hardware SDC1 and LDC1 instructions, where
available, regardless of the hardware endianness used.  This matches the
layout used by r4k_fpu.S, ensuring run-time compatibility for MIPS I
software across all o32 hardware platforms.

Define an EX2 macro to handle exceptions from both hardware instructions
implicitly produced from S.D and L.D assembly macros.
Signed-off-by: default avatarMaciej W. Rozycki <macro@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/14477/Signed-off-by: default avatarRalf Baechle <ralf@linux-mips.org>
      f92722dc
    • Maciej W. Rozycki's avatar
      MIPS: Fix ISA I/II FP signal context offsets · 758ef0a9
      Maciej W. Rozycki authored 
      Fix a regression introduced with commit 2db9ca0a ("MIPS: Use struct
mips_abi offsets to save FP context") for MIPS I/I FP signal contexts,
by converting save/restore code to the updated internal API.  Start FGR
offsets from 0 rather than SC_FPREGS from $a0 and use $a1 rather than
the offset of SC_FPC_CSR from $a0 for the Floating Point Control/Status
Register (FCSR).

Document the new internal API and adjust assembly code formatting for
consistency.
Signed-off-by: default avatarMaciej W. Rozycki <macro@imgtec.com>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/14476/Signed-off-by: default avatarRalf Baechle <ralf@linux-mips.org>
      758ef0a9
    • Maciej W. Rozycki's avatar
      MIPS: Remove FIR from ISA I FP signal context · 6daaa326
      Maciej W. Rozycki authored 
      Complement commit e50c0a8f ("Support the MIPS32 / MIPS64 DSP ASE.")
and remove the Floating Point Implementation Register (FIR) from the FP
register set recorded in a signal context with MIPS I processors too, in
line with the change applied to r4k_fpu.S.

The `sc_fpc_eir' slot is unused according to our current ABI and the FIR
register is read-only and always directly accessible from user software.

[ralf@linux-mips.org: This is also required because the next commit depends
on it.]
Signed-off-by: default avatarMaciej W. Rozycki <macro@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/14475/Signed-off-by: default avatarRalf Baechle <ralf@linux-mips.org>
      6daaa326
    • Maciej W. Rozycki's avatar
      MIPS: Fix ISA I FP sigcontext access violation handling · 35938a00
      Maciej W. Rozycki authored 
      Complement commit 0ae8dceaebe3 ("Merge with 2.3.10.") and use the local
`fault' handler to recover from FP sigcontext access violation faults,
like corresponding code does in r4k_fpu.S.  The `bad_stack' handler is
in syscall.c and is not suitable here as we want to propagate the error
condition up through the caller rather than killing the thread outright.
Signed-off-by: default avatarMaciej W. Rozycki <macro@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/14474/Signed-off-by: default avatarRalf Baechle <ralf@linux-mips.org>
      35938a00
    • Maciej W. Rozycki's avatar
      MIPS: Fix FCSR Cause bit handling for correct SIGFPE issue · 5a1aca44
      Maciej W. Rozycki authored 
      Sanitize FCSR Cause bit handling, following a trail of past attempts:

* commit 42495484 ("MIPS: ptrace: Fix FP context restoration FCSR
regression"),

* commit 443c4403 ("MIPS: Always clear FCSR cause bits after
emulation"),

* commit 64bedffe ("MIPS: Clear [MSA]FPE CSR.Cause after
notify_die()"),

* commit b1442d39 ("MIPS: Prevent user from setting FCSR cause
bits"),

* commit b54d2901517d ("Properly handle branch delay slots in connection
with signals.").

Specifically do not mask these bits out in ptrace(2) processing and send
a SIGFPE signal instead whenever a matching pair of an FCSR Cause and
Enable bit is seen as execution of an affected context is about to
resume.  Only then clear Cause bits, and even then do not clear any bits
that are set but masked with the respective Enable bits.  Adjust Cause
bit clearing throughout code likewise, except within the FPU emulator
proper where they are set according to IEEE 754 exceptions raised as the
operation emulated executed.  Do so so that any IEEE 754 exceptions
subject to their default handling are recorded like with operations
executed by FPU hardware.
Signed-off-by: default avatarMaciej W. Rozycki <macro@imgtec.com>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: James Hogan <james.hogan@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/14460/Signed-off-by: default avatarRalf Baechle <ralf@linux-mips.org>
      5a1aca44
    • Maciej W. Rozycki's avatar
      MIPS: ptrace: Also initialize the FP context on individual FCSR writes · c9e56039
      Maciej W. Rozycki authored 
      Complement commit ac9ad83b ("MIPS: prevent FP context set via ptrace
being discarded") and also initialize the FP context whenever FCSR alone
is written with a PTRACE_POKEUSR request addressing FPC_CSR, rather than
along with the full FPU register set in the case of the PTRACE_SETFPREGS
request.
Signed-off-by: default avatarMaciej W. Rozycki <macro@imgtec.com>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: James Hogan <james.hogan@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/14459/Signed-off-by: default avatarRalf Baechle <ralf@linux-mips.org>
      c9e56039
    • James Hogan's avatar
      MIPS: dump_tlb: Fix printk continuations · 8a98495c
      James Hogan authored 
      Since commit 4bcc595c ("printk: reinstate KERN_CONT for printing
continuation lines") the output from TLB dumps on MIPS has been
pretty unreadable due to the lack of KERN_CONT markers. Use pr_cont to
provide the appropriate markers & restore the expected output.

Continuation is also used for the second line of each TLB entry printed
in dump_tlb.c even though it has a newline, since it is a continuation
of the interpretation of the same TLB entry. For example:

[   46.371884] Index:  0 pgmask=16kb va=77654000 asid=73 gid=00
        [ri=0 xi=0 pa=ffc18000 c=5 d=0 v=1 g=0] [ri=0 xi=0 pa=ffc1c000 c=5 d=0 v=1 g=0]
[   46.385380] Index: 12 pgmask=16kb va=004b4000 asid=73 gid=00
        [ri=0 xi=0 pa=00000000 c=0 d=0 v=0 g=0] [ri=0 xi=0 pa=ffb00000 c=5 d=1 v=1 g=0]
Signed-off-by: default avatarJames Hogan <james.hogan@imgtec.com>
Cc: Maciej W. Rozycki <macro@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/14444/Signed-off-by: default avatarRalf Baechle <ralf@linux-mips.org>
      8a98495c
    • Paul Burton's avatar
      MIPS: Fix __show_regs() output · 752f5499
      Paul Burton authored 
      Since commit 4bcc595c ("printk: reinstate KERN_CONT for printing
continuation lines") the output from __show_regs() on MIPS has been
pretty unreadable due to the lack of KERN_CONT markers. Use pr_cont to
provide the appropriate markers & restore the expected register output.
Signed-off-by: default avatarPaul Burton <paul.burton@imgtec.com>
Signed-off-by: default avatarMatt Redfearn <matt.redfearn@imgtec.com>
Cc: Maciej W. Rozycki <macro@imgtec.com>
Cc: James Hogan <james.hogan@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/14432/Signed-off-by: default avatarRalf Baechle <ralf@linux-mips.org>
      752f5499
    • Matt Redfearn's avatar
      MIPS: traps: Fix output of show_code · 41000c58
      Matt Redfearn authored 
      Since commit 4bcc595c ("printk: reinstate KERN_CONT for printing
continuation lines") the output from show_code on MIPS has been
pretty unreadable due to the lack of KERN_CONT markers. Use pr_cont to
provide the appropriate markers & restore the expected output.
Signed-off-by: default avatarMatt Redfearn <matt.redfearn@imgtec.com>
Cc: Maciej W. Rozycki <macro@imgtec.com>
Cc: James Hogan <james.hogan@imgtec.com>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/14431/Signed-off-by: default avatarRalf Baechle <ralf@linux-mips.org>
      41000c58
  7. 03 Nov, 2016 4 commits
GitLab Nexedi Edition | About GitLab | About Nexedi | 沪ICP备2021021310号-2 | 沪ICP备2021021310号-7