Pull ARM SoC fixes from Arnd Bergmann:
 "This round of fixes has two larger changes that came in last week:

   - a couple of patches all intended to finally turn on USB support on
     various Amlogic SoC based boards. The respective driver were not
     finalized until very late before the merge window and the DT
     portion is the last bit now.

   - a defconfig update for gemini that had repeatedly missed the cut
     but that is required to actually boot any real machines with the
     default build.

  The rest are the usual small changes:

   - a fix for a nasty build regression on the OMAP memory drivers

   - a fix for a boot problem on Intel/Altera SocFPGA

   - a MAINTAINER file update

   - a couple of fixes for issues found by automated testing (kernelci,
     coverity, sparse, ...)

   - a few incorrect DT entries are updated to match the hardware"

* tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
  ARM: defconfig: Update Gemini defconfig
  ARM: s3c24xx: jive: Fix some GPIO names
  HISI LPC: Add Kconfig MFD_CORE dependency
  ARM: dts: Fix NAS4220B pin config
  MAINTAINERS: Remove myself as maintainer
  arm64: dts: correct SATA addresses for Stingray
  ARM64: dts: meson-gxm-khadas-vim2: enable the USB controller
  ARM64: dts: meson-gxl-nexbox-a95x: enable the USB controller
  ARM64: dts: meson-gxl-s905x-libretech-cc: enable the USB controller
  ARM64: dts: meson-gx-p23x-q20x: enable the USB controller
  ARM64: dts: meson-gxl-s905x-p212: enable the USB controller
  ARM64: dts: meson-gxm: add GXM specific USB host configuration
  ARM64: dts: meson-gxl: add USB host support
  ARM: OMAP2+: Fix build when using split object directories
  soc: bcm2835: Make !RASPBERRYPI_FIRMWARE dummies return failure
  soc: bcm: raspberrypi-power: Fix use of __packed
  ARM: dts: Fix cm2 and prm sizes for omap4
  ARM: socfpga_defconfig: Remove QSPI Sector 4K size force
  firmware: arm_scmi: remove redundant null check on array
  arm64: dts: juno: drop unnecessary address-cells and size-cells properties

Pull mtd fixes from Boris Brezillon:

 - Fix nanddev_mtd_erase() function to match the changes done in
   e7bfb3fd ("mtd: Stop updating erase_info->state and calling
   mtd_erase_callback()")

 - Fix a memory leak in the Tango NAND controller driver

 - Fix read/write to a suspended erase block in the CFI driver

 - Fix the DT parsing logic in the Marvell NAND controller driver

* tag 'mtd/fixes-for-4.17-rc3' of git://git.infradead.org/linux-mtd:
  mtd: rawnand: marvell: fix the chip-select DT parsing logic
  mtd: cfi: cmdset_0002: Do not allow read/write to suspend erase block.
  mtd: cfi: cmdset_0001: Workaround Micron Erase suspend bug.
  mtd: cfi: cmdset_0001: Do not allow read/write to suspend erase block.
  mtd: spi-nor: cadence-quadspi: Fix page fault kernel panic
  mtd: nand: Fix nanddev_mtd_erase()
  mtd: rawnand: tango: Fix struct clk memory leak

Pull drm fixes from Dave Airlie:
 "Pretty run of the mill for this stage in the cycle: msm, i915, amdgpu,
  qxl, virtio-gpu, sun4i fixes.

  i915:
   - Black screen fixes
   - Display w/a fix
   - HDA codec interop fix

  sun4i:
   - tbsa711 tablet regression fix

  qxl:
   - Regression fixes due to changes in TTM

  virtio:
   - Fix wait event condition

  msm:
   - DSI display fixes

  amdgpu:
   - fix hang on Carrizo
   - DP MST hang fixes
   - irq handling deadlock in DC.

  amdkfd:
   - Fix Kconfig issue
   - Clock retrieval fix
   - Sparse fixes"

* tag 'drm-fixes-for-v4.17-rc3' of git://people.freedesktop.org/~airlied/linux: (27 commits)
  drm/edid: Reset more of the display info
  drm/virtio: fix vq wait_event condition
  qxl: keep separate release_bo pointer
  qxl: fix qxl_release_{map,unmap}
  Revert "drm/sun4i: add lvds mode_valid function"
  drm/amd/display: Check dc_sink every time in MST hotplug
  drm/amd/display: Update MST edid property every time
  drm/amd/display: Don't read EDID in atomic_check
  drm/amd/display: Disallow enabling CRTC without primary plane with FB
  drm/amd/display: Fix deadlock when flushing irq
  drm/i915/fbdev: Enable late fbdev initial configuration
  drm/i915: Use ktime on wait_for
  drm/amdgpu: set COMPUTE_PGM_RSRC1 for SGPR/VGPR clearing shaders
  drm/amdkfd: fix build, select MMU_NOTIFIER
  drm/amdkfd: fix clock counter retrieval for node without GPU
  drm/amdkfd: Fix the error return code in kfd_ioctl_unmap_memory_from_gpu()
  drm/amdkfd: kfd_dev_is_large_bar() can be static
  drm/i915: Enable display WA#1183 from its correct spot
  drm/i915/audio: set minimum CD clock to twice the BCLK
  drm/msm: don't deref error pointer in the msm_fbdev_create error path
  ...

Merge tag 'arm-soc/for-4.17/devicetree-arm64-fixes' of https://github.com/Broadcom/stblinux into fixes

Pull "Broadcom devicetree-arm64 fixes for 4.17" from Florian Fainelli:

This pull request contains Broadcom ARM64-based SoCs Device Tree fixes
for 4.17, please pull the following:

- Srinath fixes the register base address of all SATA controllers on
  Stingray

* tag 'arm-soc/for-4.17/devicetree-arm64-fixes' of https://github.com/Broadcom/stblinux:
  arm64: dts: correct SATA addresses for Stingray

Merge tag 'drm-intel-fixes-2018-04-26' of git://anongit.freedesktop.org/drm/drm-intel into drm-fixes

- Fix for black screen issues (FDO #104158 and #104425)
- A correction for wrongly applied display W/A
- Fixes for HDA codec interop issue (no audio) and too eager HW timeouts

* tag 'drm-intel-fixes-2018-04-26' of git://anongit.freedesktop.org/drm/drm-intel:
  drm/i915/fbdev: Enable late fbdev initial configuration
  drm/i915: Use ktime on wait_for
  drm/i915: Enable display WA#1183 from its correct spot
  drm/i915/audio: set minimum CD clock to twice the BCLK

Pull virtio fixups from Michael Tsirkin:

 - Latest header update will break QEMU (if it's rebuilt with the new
   header) - and it seems that the code there is so fragile that any
   change in this header will break it. Add a better interface so users
   do not need to change their code every time that header changes.

 - Fix virtio console for spec compliance.

* tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost:
  virtio_console: reset on out of memory
  virtio_console: move removal code
  virtio_console: drop custom control queue cleanup
  virtio_console: free buffers after reset
  virtio: add ability to iterate over vqs
  virtio_console: don't tie bufs to a vq
  virtio_balloon: add array of stat names

Merge tag 'hwmon-for-linus-v4.17-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging

Pull hwmon fixes from Guenter Roeck:

 - Add support for new Ryzen chips to k10temp driver
   ... making Phoronix happy

 - Fix inconsistent chip access in nct6683 driver

 - Handle absence of few types of sensors in scmi driver

* tag 'hwmon-for-linus-v4.17-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging:
  hwmon: (k10temp) Add support for AMD Ryzen w/ Vega graphics
  hwmon: (k10temp) Add temperature offset for Ryzen 2700X
  hwmon: (nct6683) Enable EC access if disabled at boot
  hwmon: (scmi) handle absence of few types of sensors

Pull PCI fixes from Bjorn Helgaas:

 - fix Aardvark MRRS setting (Evan Wang)

 - clarify "bandwidth available" link status message (Jakub Kicinski)

 - update Kirin GPIO name to fix probe failure (Loic Poulain)

 - fix Aardvark IRQ usage (Victor Gu)

 - fix Aardvark config accessor issues (Victor Gu)

* tag 'pci-v4.17-fixes-1' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci:
  PCI: Add "PCIe" to pcie_print_link_status() messages
  PCI: kirin: Fix reset gpio name
  PCI: aardvark: Fix PCIe Max Read Request Size setting
  PCI: aardvark: Use ISR1 instead of ISR0 interrupt in legacy irq mode
  PCI: aardvark: Set PIO_ADDR_LS correctly in advk_pcie_rd_conf()
  PCI: aardvark: Fix logic in advk_pcie_{rd,wr}_conf()

Pull tracing fixes from Steven Rostedt:

 - Add workqueue forward declaration (for new work, but a nice clean up)

 - seftest fixes for the new histogram code

 - Print output fix for hwlat tracer

 - Fix missing system call events - due to change in x86 syscall naming

 - Fix kprobe address being used by perf being hashed

* tag 'trace-v4.17-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace:
  tracing: Fix missing tab for hwlat_detector print format
  selftests: ftrace: Add a testcase for multiple actions on trigger
  selftests: ftrace: Fix trigger extended error testcase
  kprobes: Fix random address output of blacklist file
  tracing: Fix kernel crash while using empty filter with perf
  tracing/x86: Update syscall trace events to handle new prefixed syscall func names
  tracing: Add missing forward declaration

Pull ACPI fixes from Rafael Wysocki:
 "These are two watchdog-related fixes, fix for a backlight regression
  from the 4.16 cycle that unfortunately was propagated to -stable and a
  button module modification to prevent graphics driver modules from
  failing to load due to unmet dependencies if ACPI is disabled from the
  kernel command line.

  Specifics:

   - Change the ACPI subsystem initialization ordering to initialize the
     WDAT watchodg before reserving PNP motherboard resources so as to
     allow the watchdog to allocate its resources before the PNP code
     gets to them and prevents it from working correctly (Mika
     Westerberg).

   - Add a quirk for Lenovo Z50-70 to use the iTCO watchdog instead of
     the WDAT one which conflicts with the RTC on that platform (Mika
     Westerberg).

   - Avoid breaking backlight handling on Dell XPS 13 2013 model by
     allowing laptops to use the ACPI backlight by default even if they
     are Windows 8-ready in principle (Hans de Goede)"

* tag 'acpi-4.17-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
  ACPI / video: Only default only_lcd to true on Win8-ready _desktops_
  ACPI / button: make module loadable when booted in non-ACPI mode
  ACPI / watchdog: Prefer iTCO_wdt on Lenovo Z50-70
  ACPI / scan: Initialize watchdog before PNP

Pull power management fixes from Rafael Wysocki:
 "These are a Low Power S0 Idle quirk, a hibernation handling fix for
  the PCI bus type and a brcmstb-avs-cpufreq driver fixup removing
  development debug code from it.

  Specifics:

   - Blacklist the Low Power S0 Idle _DSM on ThinkPad X1 Tablet(2016)
     where it causes issues and make it use ACPI S3 which works instead
     of the non-working suspend-to-idle by default (Chen Yu).

   - Fix the handling of hibernation in the PCI core for devices with
     the DPM_FLAG_SMART_SUSPEND flag set to fix a regression affecting
     intel-lpss I2C devices (Mika Westerberg).

   - Drop development debug code from the brcmstb-avs-cpufreq driver
     (Markus Mayer)"

* tag 'pm-4.17-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
  cpufreq: brcmstb-avs-cpufreq: remove development debug support
  PCI / PM: Do not clear state_saved in pci_pm_freeze() when smart suspend is set
  ACPI / PM: Blacklist Low Power S0 Idle _DSM for ThinkPad X1 Tablet(2016)

Pull /dev/random fixes from Ted Ts'o:
 "Fix a regression on NUMA kernels and suppress excess unseeded entropy
  pool warnings"

* tag 'random_for_linus_stable' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/random:
  random: rate limit unseeded randomness warnings
  random: fix possible sleeping allocation from irq context

Pull s390 fixes from Martin Schwidefsky:
 "A couple of bug fixes:

   - correct some CPU-MF counter names for z13 and z14

   - correct locking in the vfio-ccw fsm_io_helper function

   - provide arch_uretprobe_is_alive to avoid sigsegv with uretprobes

   - fix a corner case with CPU-MF sampling in regard to execve

   - fix expoline code revert for loadable modules

   - update chpid descriptor for resource accessibility events

   - fix dasd I/O errors due to outdated device alias infomation"

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
  s390: correct module section names for expoline code revert
  vfio: ccw: process ssch with interrupts disabled
  s390: update sampling tag after task pid change
  s390/cpum_cf: rename IBM z13/z14 counter names
  s390/dasd: fix IO error for newly defined devices
  s390/uprobes: implement arch_uretprobe_is_alive()
  s390/cio: update chpid descriptor after resource accessibility event

The block responsible of parsing the DT for the number of chip-select
lines uses an 'if/else if/else if' block. The content of the second and
third 'else if' conditions are:
        1/ the actual condition to enter the sub-block and
        2/ the operation to do in this sub-block.

        [...]
        else if (condition1_to_enter && action1() == failed)
                raise_error();
        else if (condition2_to_enter && action2() == failed)
                raise_error();
        [...]

In case of failure, the sub-block is entered and an error raised.
Otherwise, in case of success, the code would continue erroneously in
the next 'else if' statement because it did not failed (and did not
enter the first 'else if' sub-block).

The first 'else if' refers to legacy bindings while the second 'else if'
refers to new bindings. The second 'else if', which is entered
erroneously, checks for the 'reg' property, which, for old bindings,
does not mean anything because it would not be the number of CS
available, but the regular register map of almost any DT node. This
being said, the content of the 'reg' property being the register map
offset and length, it has '2' values, so the number of CS in this
situation is assumed to be '2'.

When running nand_scan_ident() with 2 CS, the core will check for an
array of chips. It will first issue a RESET and then a READ_ID. Of
course this will trigger two timeouts because there is no chip in front
of the second CS:

[    1.367460] marvell-nfc f2720000.nand: Timeout on CMDD (NDSR: 0x00000080)
[    1.474292] marvell-nfc f2720000.nand: Timeout on CMDD (NDSR: 0x00000280)

Indeed, this is harmless and the core will then assume there is only one
valid CS.

Fix the logic in the whole block by entering each sub-block just on the
'is legacy' condition, doing the action inside the sub-block. This way,
when the action succeeds, the whole block is left.

Furthermore, for both the old bindings and the new bindings the same
logic was applied to retrieve the number of CS lines:
using of_get_property() to get a size in bytes, converted in the actual
number of lines by dividing it per sizeof(u32) (4 bytes).

This is fine for the 'reg' property which is a list of the CS IDs but
not for the 'num-cs' property which is directly the value of the number
of CS.

Anyway, no existing DT uses another value than 'num-cs = <1>' and no
other value has ever been supported by the old driver (pxa3xx_nand.c).
Remove this condition and apply a number of 1 CS anyway, as already
described in the bindings.

Finally, the 'reg' property of a 'nand' node (with the new bindings)
gives the IDs of each CS line in use. marvell_nand.c driver first look
at the number of CS lines that are present in this property.

Better use of_property_count_elems_of_size() than dividing by 4 the size
of the number of bytes returned by of_get_property().

Fixes: 02f26ecf ("mtd: nand: add reworked Marvell NAND controller driver")
Cc: stable@vger.kernel.org
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Tested-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>

This updates the Gemini defconfig with a config that will bring
up most of the recently merged and updated devices to some
functional level:

- We enable high resolution timers (the right thing to do)
- Enable CMA for the framebuffer, and the new TVE200
  framebuffer driver and the Ilitek ILI9322 driver for
  graphics on the D-Link DIR-685. HIGHMEM support comes in
  as part of this.
- Enable networking and the new Cortina Gemini ethernet
  driver.
- Enable MDIO over GPIO and the Realtek PHY devices used on
  several of these systems.
- Enable I2C over GPIO and SPI over GPIO which is used on
  several of these devices.
- Enable the Thermal framework, GPIO fan control and LM75 sensor
  adding cooling on the D-Link DNS-313 with no userspace
  involved even if only the kernel is working, rock solid
  thermal for this platform.
- Enable JEDEC flash probing to support the Eon flash chip in
  D-Link DNS-313.
- Enable LED disk triggers for the NAS type devices.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>

One of the bitbanged SPI hosts had wrongly named GPIO lines due to
sloppiness by yours truly.

Cc: arm@kernel.org
Cc: Mark Brown <broonie@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>

Merge tag 'omap-for-v4.17/fixes-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into fixes

Pull "Two fixes for v4.17-rc cycle" from Tony Lindgren:

Fix a build regression with split object directories reported by Russell
and fix range sizes for omap4 cm2 and prm modules.

* tag 'omap-for-v4.17/fixes-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
  ARM: OMAP2+: Fix build when using split object directories
  ARM: dts: Fix cm2 and prm sizes for omap4

For ACPI support of the HiSilicon LPC driver we depend
on MFD_CORE config.

Currently the HiSi LPC Kconfig entry does not define this
dependency, so add it.

The reason for depending on MFD_CORE in the driver is
that we model the LPC host as an MFD, in that a platform
device will be created for each device on the bus.

We do this as we need to modify the resources of these
derived platform devices, something which we should not
do to the original devices created in the ACPI scan.
Details in e0aa1563 ("HISI LPC: Add ACPI support").

Fixes: e0aa1563 ("HISI LPC: Add ACPI support")
Reported-and-tested-by: Tan Xiaojun <tanxiaojun@huawei.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>

Merge tag 'amlogic-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/khilman/linux-amlogic into fixes

Pull "Amlogic fixes for v4.17-rc1" from Kevin Hilman:
- add / enable USB host support for GX boards

* tag 'amlogic-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/khilman/linux-amlogic:
  ARM64: dts: meson-gxm-khadas-vim2: enable the USB controller
  ARM64: dts: meson-gxl-nexbox-a95x: enable the USB controller
  ARM64: dts: meson-gxl-s905x-libretech-cc: enable the USB controller
  ARM64: dts: meson-gx-p23x-q20x: enable the USB controller
  ARM64: dts: meson-gxl-s905x-p212: enable the USB controller
  ARM64: dts: meson-gxm: add GXM specific USB host configuration
  ARM64: dts: meson-gxl: add USB host support

The DTS file for the NAS4220B had the pin config for the
ethernet interface set to the pins in the SL3512 SoC while
this system is using SL3516. Fix it by referencing the
right SL3516 pins instead of the SL3512 pins.

Cc: stable@vger.kernel.org
Cc: Hans Ulli Kroll <ulli.kroll@googlemail.com>
Reported-by: Andreas Fiedler <andreas.fiedler@gmx.net>
Reported-by: Roman Yeryomin <roman@advem.lv>
Tested-by: Roman Yeryomin <roman@advem.lv>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>

I am leaving Axis, so this address will bounce in the not too
distant future.

Fortunately, I will still be working with the community.
Signed-off-by: Niklas Cassel <niklas.cassel@axis.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>

Merge tag 'scmi-fixes-4.17' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/sudeep.holla/linux into fixes

SCMI fix for v4.17

A single patch eliminating the redundant null pointer check detected
by CoverityScan("Array compared against 0")

* tag 'scmi-fixes-4.17' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/sudeep.holla/linux:
  firmware: arm_scmi: remove redundant null check on array

Merge tag 'juno-fixes-4.17' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/sudeep.holla/linux into fixes

Pull "ARMv8 Juno DT fix for v4.17" from Sudeep Holla:

A single patch to fix the new DTC warnings probably enabled during
v4.17 merge window.

* tag 'juno-fixes-4.17' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/sudeep.holla/linux:
  arm64: dts: juno: drop unnecessary address-cells and size-cells properties

This pull request contains Broadcom SoCs drivers fixes, please pull the
following:

- Geert makes the Raspberry Pi firmwware return -ENOSYS (similar to
  other subsystems) when CONFIG_RASPBERRYPI_FIRMWARE is off.

- Florian fixes an incorrect annotation in the Raspberry Pi power domain
  driver, spotted by sparse

* tag 'arm-soc/for-4.17/drivers-fixes' of https://github.com/Broadcom/stblinux:
  soc: bcm2835: Make !RASPBERRYPI_FIRMWARE dummies return failure
  soc: bcm: raspberrypi-power: Fix use of __packed

Merge tag 'socfpga_defconfig_fix_v4.17' of git://git.kernel.org/pub/scm/linux/kernel/git/dinguyen/linux into fixes

ARM: socfpga_defconfig: fix QSPI Sector 4k
- disable CONFIG_MTD_SPI_NOR_USE_4K_SECTORS

* tag 'socfpga_defconfig_fix_v4.17' of git://git.kernel.org/pub/scm/linux/kernel/git/dinguyen/linux:
  ARM: socfpga_defconfig: Remove QSPI Sector 4K size force

* acpi-watchdog:
  ACPI / watchdog: Prefer iTCO_wdt on Lenovo Z50-70

* acpi-button:
  ACPI / button: make module loadable when booted in non-ACPI mode

* acpi-video:
  ACPI / video: Only default only_lcd to true on Win8-ready _desktops_

* acpi-pm:
  ACPI / PM: Blacklist Low Power S0 Idle _DSM for ThinkPad X1 Tablet(2016)

* pm-cpufreq:
  cpufreq: brcmstb-avs-cpufreq: remove development debug support

Pull fsnotify fix from Jan Kara:
 "A fix of a fsnotify race causing panics / softlockups"

* tag 'for_v4.17-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/jack/linux-fs:
  fsnotify: Fix fsnotify_mark_connector race

Pull SCSI fixes from James Bottomley:
 "Eight bug fixes, one spelling update and one tracepoint addition.

  The most serious is probably the mptsas write same fix because it
  means anyone using these controllers sees errors when modern
  filesystems try to issue discards"

* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
  scsi: target: fix crash with iscsi target and dvd
  scsi: sd_zbc: Avoid that resetting a zone fails sporadically
  scsi: sd: Defer spinning up drive while SANITIZE is in progress
  scsi: megaraid_sas: Do not log an error if FW successfully initializes.
  scsi: ufs: add trace event for ufs upiu
  scsi: core: remove reference to scsi_show_extd_sense()
  scsi: mptsas: Disable WRITE SAME
  scsi: fnic: fix spelling mistake in fnic stats "Abord" -> "Abort"
  scsi: scsi_debug: IMMED related delay adjustments
  scsi: iscsi: respond to netlink with unicast when appropriate

Pull block updates from Jens Axboe:
 "I ended up sitting on this about a week longer than I wanted to, since
  we were hashing out details with a timeout change. I've now killed
  that patch, so we can flush the existing queue in due time.

  This contains:

   - Fix for an old regression, where entering the queue can be
     disturbed by a signal to the process. This can cause spurious EIO.
     Fix from Alan Jenkins.

   - cdrom information leak fix from Dan.

   - Trivial helper for testing queue FUA from Dave Chinner, part of his
     O_DIRECT FUA series.

   - Series of swim fixes from Finn that actually makes it work again.

   - Loop O_DIRECT corruption fix, which caused data corruption in
     production for us. From me.

   - BFQ crash fix from me.

   - bcache maintainer update. Michael no longer has the time to do it,
     Coly has stepped up to serve as the new maintainer.

   - blkcg locking fixes from Jiang Biao.

   - Revert of a change from this merge window from Ming, that causes an
     issue on some hardware.

   - Minor clarification doc addition from Linus Walleij"

* tag 'for-linus-20180425' of git://git.kernel.dk/linux-block: (22 commits)
  Revert "blk-mq: remove code for dealing with remapping queue"
  block: mq: Add some minor doc for core structs
  bcache: mark Coly Li as bcache maintainer
  MAINTAINERS: Remove me as maintainer of bcache
  blkcg: init root blkcg_gq under lock
  blkcg: small fix on comment in blkcg_init_queue
  blkcg: don't hold blkcg lock when deactivating policy
  block: add blk_queue_fua() helper function
  cdrom: information leak in cdrom_ioctl_media_changed()
  bfq-iosched: ensure to clear bic/bfqq pointers when preparing request
  blk-mq: start request gstate with gen 1
  block/swim: Select appropriate drive on device open
  block/swim: Fix IO error at end of medium
  block/swim: Check drive type
  block/swim: Rename macros to avoid inconsistent inverted logic
  block/swim: Don't log an error message for an invalid ioctl
  block/swim: Remove extra put_disk() call from error path
  block/swim: Fix array bounds check
  m68k/mac: Don't remap SWIM MMIO region
  loop: handle short DIO reads
  ...

Merge tag 'riscv-for-linus-4.17-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/palmer/riscv-linux

Pull RISC-V fixes from Palmer Dabbelt:
 "This contains three small fixes related to the RISC-V port that I'd
  like to target for 4.17-rc3:

   - a Kconfig cleanup to select DMA_DIRECT_OPS instead of redefining it
     in arch/riscv

   - the removal of asm/handle_irq.h, which doesn't exist, from our arch
     header list

   - the addition of "-no-pie" the link rules for our VDSO-related
     files, which fixes the build on systems where PIE is enabled by
     default"

* tag 'riscv-for-linus-4.17-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/palmer/riscv-linux:
  RISC-V: build vdso-dummy.o with -no-pie
  riscv: there is no <asm/handle_irq.h>
  riscv: select DMA_DIRECT_OPS instead of redefining it

sun41: Fix regression for TBSA711 tablet (Ondrej)
qxl: 2 bug fixes (Gerd)
core: Don't use stale display info between HDMI hotplugs (Ville)
virtio: Fix guest spinning when request queue is full (Gerd)

Cc: Ondrej Jirman <megous@megous.com>
Cc: Gerd Hoffmann <kraxel@redhat.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>

* tag 'drm-misc-fixes-2018-04-25' of git://anongit.freedesktop.org/drm/drm-misc:
  drm/edid: Reset more of the display info
  drm/virtio: fix vq wait_event condition
  qxl: keep separate release_bo pointer
  qxl: fix qxl_release_{map,unmap}
  Revert "drm/sun4i: add lvds mode_valid function"

A few fixes for 4.17.. thanks to Sean for helping pull together some
of the display related fixes while I was off in compute-land.

* tag 'drm-msm-fixes-2018-04-25' of git://people.freedesktop.org/~robclark/linux:
  drm/msm: don't deref error pointer in the msm_fbdev_create error path
  drm/msm/dsi: use correct enum in dsi_get_cmd_fmt
  drm/msm: Fix possible null dereference on failure of get_pages()
  drm/msm: Add modifier to mdp_get_format arguments
  drm/msm: Mark the crtc->state->event consumed
  drm/msm/dsi: implement auto PHY timing calculator for 10nm PHY
  drm/msm/dsi: check video mode engine status before waiting
  drm/msm/dsi: check return value for video done waits

- Fix a hang on CZ boards with EDC enabled
- Fix hangs related to DP MST handling
- Fix a deadlock in irq handling in DC

* 'drm-fixes-4.17' of git://people.freedesktop.org/~agd5f/linux:
  drm/amd/display: Check dc_sink every time in MST hotplug
  drm/amd/display: Update MST edid property every time
  drm/amd/display: Don't read EDID in atomic_check
  drm/amd/display: Disallow enabling CRTC without primary plane with FB
  drm/amd/display: Fix deadlock when flushing irq
  drm/amdgpu: set COMPUTE_PGM_RSRC1 for SGPR/VGPR clearing shaders

Merge tag 'drm-amdkfd-fixes-2018-04-24' of git://people.freedesktop.org/~gabbayo/linux into drm-fixes

- fix amdkfd Kconfig to select MMU_NOTIFIER
- allow clock retrieval in case GPU not present
- fix return code from function
- make function static (fix sparse warning)

* tag 'drm-amdkfd-fixes-2018-04-24' of git://people.freedesktop.org/~gabbayo/linux:
  drm/amdkfd: fix build, select MMU_NOTIFIER
  drm/amdkfd: fix clock counter retrieval for node without GPU
  drm/amdkfd: Fix the error return code in kfd_ioctl_unmap_memory_from_gpu()
  drm/amdkfd: kfd_dev_is_large_bar() can be static

We're currently failing to reset everything in display_info.hdmi
which will potentially cause us to use stale information when
swapping monitors. Eg. if the user replaces a HDMI 2.0 monitor
with a HDMI 1.x monitor we will continue to think that the monitor
supports scrambling. That will lead to a black screen since the
HDMI 1.x monitor won't understand the scrambled signal.

Fix the problem by clearing display_info.hdmi fully. And while at
eliminate some duplicated code by calling drm_reset_display_info()
in drm_add_display_info().

Cc: stable@vger.kernel.org
Cc: Antony Chen <antonychen@qnap.com>
Cc: Shashank Sharma <shashank.sharma@intel.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=105655Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180424130250.7028-1-ville.syrjala@linux.intel.comReviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Tested-by: Antony Chen <antonychen@qnap.com>
Signed-off-by: Sean Paul <seanpaul@chromium.org>

Wait until we have enough space in the virt queue to actually queue up
our request.  Avoids the guest spinning in case we have a non-zero
amount of free entries but not enough for the request.

Cc: stable@vger.kernel.org
Reported-by: Alain Magloire <amagloire@blackberry.com>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Dave Airlie <airlied@redhat.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20180403095904.11152-1-kraxel@redhat.comSigned-off-by: Sean Paul <seanpaul@chromium.org>

qxl expects that list_first_entry(release->bos) returns the first
element qxl added to the list.  ttm_eu_reserve_buffers() may reorder
the list though.

Add a release_bo field to struct qxl_release and use that instead.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Dave Airlie <airlied@redhat.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/20180418054257.15388-3-kraxel@redhat.comSigned-off-by: Sean Paul <seanpaul@chromium.org>

s/PAGE_SIZE/PAGE_MASK/

Luckily release_offset is never larger than PAGE_SIZE, so the bug has no
bad side effects and managed to stay unnoticed for years that way ...
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Dave Airlie <airlied@redhat.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/20180418054257.15388-2-kraxel@redhat.comSigned-off-by: Sean Paul <seanpaul@chromium.org>

The reverted commit broke LVDS output on TBS A711 Tablet. That tablet
has simple-panel node that has fixed pixel clock-frequency that A83T
SoC used in the tablet can't generate exactly.

Requested rate is 52000000 and rounded_rate is calculated as 51857142.
It's close enough for it to work in practice, but with strict check
in the reverted commit, the mode is rejected needlessly in this case.

DT allows to specify a range of values for simple-panel/clock-frequency,
but driver doesn't respect that ATM. Given that TBS A711 is the single
user of sun4i-lvds driver, let's revert that commit for now, until
a better solution for the problem is found.

Also see: https://patchwork.kernel.org/patch/9446385/ for relevant
discussion (or search for "[RFC] drm/sun4i: rgb: Add 5% tolerance
to dot clock frequency check").

Fixes: e4e4b7ad ("drm/sun4i: add lvds mode_valid function")
Reported-by: Ondrej Jirman <megous@megous.com>
Signed-off-by: Ondrej Jirman <megous@megous.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180421045155.15332-1-megous@megous.comSigned-off-by: Sean Paul <seanpaul@chromium.org>