The code currently uses variables to store and never modify the bit masks
of interrupts. This is legacy code from an early version of the driver
that supported MIPS based SoCs where the IRQ bits depended on the actual
SoC. As the bits are the same for all ARM based SoCs using this driver we
can remove the intermediate variables.
Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

The driver was originally written for MIPS based SoC. These required the
IRQ mask register to be read after writing it to ensure that the content
was actually applied. As this version only works on ARM based SoCs, we can
safely remove the 2 reads as they are no longer required.
Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

When adding rule with NLM_F_EXCL flag then check if the same rule exist.
If yes then exit with -EEXIST.

This is already implemented in iproute2:
        if (cmd == RTM_NEWRULE) {
                req.n.nlmsg_flags |= NLM_F_CREATE|NLM_F_EXCL;
                req.r.rtm_type = RTN_UNICAST;
        }

Tested ipv4 and ipv6 with net-next linux on qemu x86

expected behavior after patch:
localhost ~ # ip rule
0:    from all lookup local
32766:    from all lookup main
32767:    from all lookup default
localhost ~ # ip rule add from 10.46.177.97 lookup 104 pref 1005
localhost ~ # ip rule add from 10.46.177.97 lookup 104 pref 1005
RTNETLINK answers: File exists
localhost ~ # ip rule
0:    from all lookup local
1005:    from 10.46.177.97 lookup 104
32766:    from all lookup main
32767:    from all lookup default

There was already topic regarding this but I don't see any changes
merged and problem still occurs.
https://lkml.kernel.org/r/1135778809.5944.7.camel+%28%29+localhost+%21+localdomainSigned-off-by: Mateusz Bajorski <mateusz.bajorski@nokia.com>
Acked-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In previous commit 01f83d69
the following comments were added:

"When peer uses tiny windows, there is no use in packetizing to sub-MSS
pieces for the sake of SWS or making sure there are enough packets in
the pipe for fast recovery."

The test should be > TCP_MSS_DEFAULT not >= 512. This allows low end
devices that send an MSS of 536 (TCP_MSS_DEFAULT) to see better network
performance by sending it 536 bytes of data at a time instead of bounding
to half window size (268). Other network stacks work this way, e.g. HP-UX.
Signed-off-by: Shane Seymour <shane.seymour@hpe.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

We found that sometimes a restored tcp socket doesn't work.

A reason of this bug is incorrect window parameters and in this case
tcp_acceptable_seq() returns tcp_wnd_end(tp) instead of tp->snd_nxt. The
other side drops packets with this seq, because seq is less than
tp->rcv_nxt ( tcp_sequence() ).

Data from a send queue is sent only if there is enough space in a
window, so when we restore unacked data, we need to expand a window to
fit this data.

This was in a first version of this patch:
"tcp: extend window to fit all restored unacked data in a send queue"

Then Alexey recommended me to restore window parameters instead of
adjusted them according with data in a sent queue. This sounds resonable.

rcv_wnd has to be restored, because it was reported to another side
and the offered window is never shrunk.
One of reasons why we need to restore snd_wnd was described above.

Cc: Pavel Emelyanov <xemul@parallels.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Alexey Kuznetsov <kuznet@ms2.inr.ac.ru>
Cc: James Morris <jmorris@namei.org>
Cc: Hideaki YOSHIFUJI <yoshfuji@linux-ipv6.org>
Cc: Patrick McHardy <kaber@trash.net>
Signed-off-by: Andrey Vagin <avagin@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Nikolay Aleksandrov says:

====================
net: bridge: add support for IGMP/MLD stats

This patchset adds support for the new IFLA_STATS_LINK_XSTATS_SLAVE
attribute which can be used with RTM_GETSTATS in order to export per-slave
statistics. It works by passing the attribute to the linkxstats callback
and if the callback user supports it - it should dump that slave's stats.
This is much more scalable and permits us to request only a single port's
statistics instead of dumping everything every time.
The second patch adds support for per-port IGMP/MLD statistics and uses
the new API to export them for the bridge and its ports. The stats are
made in a very lightweight manner, the normal fast-path is not affected
at all and the flood paths (br_flood/br_multicast_flood) are only affected
if the packet is IGMP and the IGMP stats have been enabled using cache-hot
data for the check.

v2: Patch 01 is new, patch 02 has been reworked to use the new API, also
in addition counters for IGMP/MLD parse errors have been added and members
are added for per-port multicast traffic stats. The multicast counting has
been slightly optimized (moved the br_multicast_count inside the IPv4/6
IGMP functions after the checks for IGMP traffic) to avoid one conditional
that was on all of the multicast traffic path (both IGMP and other).
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch adds stats support for the currently used IGMP/MLD types by the
bridge. The stats are per-port (plus one stat per-bridge) and per-direction
(RX/TX). The stats are exported via netlink via the new linkxstats API
(RTM_GETSTATS). In order to minimize the performance impact, a new option
is used to enable/disable the stats - multicast_stats_enabled, similar to
the recent vlan stats. Also in order to avoid multiple IGMP/MLD type
lookups and checks, we make use of the current "igmp" member of the bridge
private skb->cb region to record the type on Rx (both host-generated and
external packets pass by multicast_rcv()). We can do that since the igmp
member was used as a boolean and all the valid IGMP/MLD types are positive
values. The normal bridge fast-path is not affected at all, the only
affected paths are the flooding ones and since we make use of the IGMP/MLD
type, we can quickly determine if the packet should be counted using
cache-hot data (cb's igmp member). We add counters for:
* IGMP Queries
* IGMP Leaves
* IGMP v1/v2/v3 reports

* MLD Queries
* MLD Leaves
* MLD v1/v2 reports

These are invaluable when monitoring or debugging complex multicast setups
with bridges.
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch adds support for the IFLA_STATS_LINK_XSTATS_SLAVE attribute
which allows to export per-slave statistics if the master device supports
the linkxstats callback. The attribute is passed down to the linkxstats
callback and it is up to the callback user to use it (an example has been
added to the only current user - the bridge). This allows us to query only
specific slaves of master devices like bridge ports and export only what
we're interested in instead of having to dump all ports and searching only
for a single one. This will be used to export per-port IGMP/MLD stats and
also per-port vlan stats in the future, possibly other statistics as well.
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Daniel Borkmann says:

====================
BPF helper improvements

This set adds various BPF helper improvements, that is, cleaning
up and adding BPF_F_CURRENT_CPU flag for tracing helper, allowing
for preemption checks on bpf_get_smp_processor_id() helper, and
adding two new helpers bpf_skb_change_{proto, type} for tc related
programs. For further details please see individual patches.

Note, this set requires -net to be merged into -net-next tree first.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

This work adds a helper for changing skb->pkt_type in a controlled way.
We only allow a subset of possible values and can extend that in future
should other use cases come up. Doing this as a helper has the advantage
that errors can be handeled gracefully and thus helper kept extensible.

It's a write counterpart to pkt_type member we can already read from
struct __sk_buff context. Major use case is to change incoming skbs to
PACKET_HOST in a programmatic way instead of having to recirculate via
redirect(..., BPF_F_INGRESS), for example.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch adds a minimal helper for doing the groundwork of changing
the skb->protocol in a controlled way. Currently supported is v4 to
v6 and vice versa transitions, which allows f.e. for a minimal, static
nat64 implementation where applications in containers that still
require IPv4 can be transparently operated in an IPv6-only environment.
For example, host facing veth of the container can transparently do
the transitions in a programmatic way with the help of clsact qdisc
and cls_bpf.

Idea is to separate concerns for keeping complexity of the helper
lower, which means that the programs utilize bpf_skb_change_proto(),
bpf_skb_store_bytes() and bpf_lX_csum_replace() to get the job done,
instead of doing everything in a single helper (and thus partially
duplicating helper functionality). Also, bpf_skb_change_proto()
shouldn't need to deal with raw packet data as this is done by other
helpers.

bpf_skb_proto_6_to_4() and bpf_skb_proto_4_to_6() unclone the skb to
operate on a private one, push or pop additionally required header
space and migrate the gso/gro meta data from the shared info. We do
mark the gso type as dodgy so that headers are checked and segs
recalculated by the gso/gro engine. The gso_size target is adapted
as well. The flags argument added is currently reserved and can be
used for future extensions.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Use smp_processor_id() for the generic helper bpf_get_smp_processor_id()
instead of the raw variant. This allows for preemption checks when we
have DEBUG_PREEMPT, and otherwise uses the raw variant anyway. We only
need to keep the raw variant for socket filters, but we can reuse the
helper that is already there from cBPF side.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Follow-up commit to 1e33759c ("bpf, trace: add BPF_F_CURRENT_CPU
flag for bpf_perf_event_output") to add the same functionality into
bpf_perf_event_read() helper. The split of index into flags and index
component is also safe here, since such large maps are rejected during
map allocation time.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

We currently have two invocations, which is unnecessary. Fetch it only
once and use the smp_processor_id() variant, so we also get preemption
checks along with it when DEBUG_PREEMPT is set.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Some minor cleanups: i) Remove the unlikely() from fd array map lookups
and let the CPU branch predictor do its job, scenarios where there is not
always a map entry are very well valid. ii) Move the attribute type check
in the bpf_perf_event_read() helper a bit earlier so it's consistent wrt
checks with bpf_perf_event_output() helper as well. iii) remove some
comments that are self-documenting in kprobe_prog_is_valid_access() and
therefore make it consistent to tp_prog_is_valid_access() as well.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Several cases of overlapping changes, except the packet scheduler
conflicts which deal with the addition of the free list parameter
to qdisc_enqueue().
Signed-off-by: David S. Miller <davem@davemloft.net>

Pull NFS client bugfixes from Anna Schumaker:
 "Stable bugfixes:
   - Fix _cancel_empty_pagelist
   - Fix a double page unlock
   - Make nfs_atomic_open() call d_drop() on all ->open_context() errors.
   - Fix another OPEN_DOWNGRADE bug

  Other bugfixes:
   - Ensure we handle delegation errors in nfs4_proc_layoutget()
   - Layout stateids start out as being invalid
   - Add sparse lock annotations for pnfs_find_alloc_layout
   - Handle bad delegation stateids in nfs4_layoutget_handle_exception
   - Fix up O_DIRECT results
   - Fix potential use after free of state in nfs4_do_reclaim.
   - Mark the layout stateid invalid when all segments are removed
   - Don't let readdirplus revalidate an inode that was marked as stale
   - Fix potential race in nfs_fhget()
   - Fix an unused variable warning"

* tag 'nfs-for-4.7-2' of git://git.linux-nfs.org/projects/anna/linux-nfs:
  NFS: Fix another OPEN_DOWNGRADE bug
  make nfs_atomic_open() call d_drop() on all ->open_context() errors.
  NFS: Fix an unused variable warning
  NFS: Fix potential race in nfs_fhget()
  NFS: Don't let readdirplus revalidate an inode that was marked as stale
  NFSv4.1/pnfs: Mark the layout stateid invalid when all segments are removed
  NFS: Fix a double page unlock
  pnfs_nfs: fix _cancel_empty_pagelist
  nfs4: Fix potential use after free of state in nfs4_do_reclaim.
  NFS: Fix up O_DIRECT results
  NFS/pnfs: handle bad delegation stateids in nfs4_layoutget_handle_exception
  NFSv4.1/pnfs: Add sparse lock annotations for pnfs_find_alloc_layout
  NFSv4.1/pnfs: Layout stateids start out as being invalid
  NFSv4.1/pnfs: Ensure we handle delegation errors in nfs4_proc_layoutget()

Pull audit fixes from Paul Moore:
 "Two small patches to fix audit problems in 4.7-rcX: the first fixes a
  potential kref leak, the second removes some header file noise.

  The first is an important bug fix that really should go in before 4.7
  is released, the second is not critical, but falls into the very-nice-
  to-have category so I'm including in the pull request.

  Both patches are straightforward, self-contained, and pass our
  testsuite without problem"

* 'stable-4.7' of git://git.infradead.org/users/pcmoore/audit:
  audit: move audit_get_tty to reduce scope and kabi changes
  audit: move calcs after alloc and check when logging set loginuid

Pull networking fixes from David Miller:
 "I've been traveling so this accumulates more than week or so of bug
  fixing.  It perhaps looks a little worse than it really is.

   1) Fix deadlock in ath10k driver, from Ben Greear.

   2) Increase scan timeout in iwlwifi, from Luca Coelho.

   3) Unbreak STP by properly reinjecting STP packets back into the
      stack.  Regression fix from Ido Schimmel.

   4) Mediatek driver fixes (missing malloc failure checks, leaking of
      scratch memory, wrong indexing when mapping TX buffers, etc.) from
      John Crispin.

   5) Fix endianness bug in icmpv6_err() handler, from Hannes Frederic
      Sowa.

   6) Fix hashing of flows in UDP in the ruseport case, from Xuemin Su.

   7) Fix netlink notifications in ovs for tunnels, delete link messages
      are never emitted because of how the device registry state is
      handled.  From Nicolas Dichtel.

   8) Conntrack module leaks kmemcache on unload, from Florian Westphal.

   9) Prevent endless jump loops in nft rules, from Liping Zhang and
      Pablo Neira Ayuso.

  10) Not early enough spinlock initialization in mlx4, from Eric
      Dumazet.

  11) Bind refcount leak in act_ipt, from Cong WANG.

  12) Missing RCU locking in HTB scheduler, from Florian Westphal.

  13) Several small MACSEC bug fixes from Sabrina Dubroca (missing RCU
      barrier, using heap for SG and IV, and erroneous use of async flag
      when allocating AEAD conext.)

  14) RCU handling fix in TIPC, from Ying Xue.

  15) Pass correct protocol down into ipv4_{update_pmtu,redirect}() in
      SIT driver, from Simon Horman.

  16) Socket timer deadlock fix in TIPC from Jon Paul Maloy.

  17) Fix potential deadlock in team enslave, from Ido Schimmel.

  18) Memory leak in KCM procfs handling, from Jiri Slaby.

  19) ESN generation fix in ipv4 ESP, from Herbert Xu.

  20) Fix GFP_KERNEL allocations with locks held in act_ife, from Cong
      WANG.

  21) Use after free in netem, from Eric Dumazet.

  22) Uninitialized last assert time in multicast router code, from Tom
      Goff.

  23) Skip raw sockets in sock_diag destruction broadcast, from Willem
      de Bruijn.

  24) Fix link status reporting in thunderx, from Sunil Goutham.

  25) Limit resegmentation of retransmit queue so that we do not
      retransmit too large GSO frames.  From Eric Dumazet.

  26) Delay bpf program release after grace period, from Daniel
      Borkmann"

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (141 commits)
  openvswitch: fix conntrack netlink event delivery
  qed: Protect the doorbell BAR with the write barriers.
  neigh: Explicitly declare RCU-bh read side critical section in neigh_xmit()
  e1000e: keep VLAN interfaces functional after rxvlan off
  cfg80211: fix proto in ieee80211_data_to_8023 for frames without LLC header
  qlcnic: use the correct ring in qlcnic_83xx_process_rcv_ring_diag()
  bpf, perf: delay release of BPF prog after grace period
  net: bridge: fix vlan stats continue counter
  tcp: do not send too big packets at retransmit time
  ibmvnic: fix to use list_for_each_safe() when delete items
  net: thunderx: Fix TL4 configuration for secondary Qsets
  net: thunderx: Fix link status reporting
  net/mlx5e: Reorganize ethtool statistics
  net/mlx5e: Fix number of PFC counters reported to ethtool
  net/mlx5e: Prevent adding the same vxlan port
  net/mlx5e: Check for BlueFlame capability before allocating SQ uar
  net/mlx5e: Change enum to better reflect usage
  net/mlx5: Add ConnectX-5 PCIe 4.0 to list of supported devices
  net/mlx5: Update command strings
  net: marvell: Add separate config ANEG function for Marvell 88E1111
  ...

Pull s390 fixes from Martin Schwidefsky:
 "Another two bug fixes for 4.7:

   - The revert of patch which removed boot information for systems
     using an intermediate boot kernel, e.g. the SLES12 grub setup.

   - A fix for an incorrect inline assembly constraint that causes
     broken code to be generated with gcc 4.8.5"

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
  s390: fix test_fp_ctl inline assembly contraints
  Revert "s390/kdump: Clear subchannel ID to signal non-CCW/SCSI IPL"

Pull pin control fixes from Linus Walleij:
 "Here are a bunch of fixes for pin control.  Just drivers and a
  MAINTAINERS fixup:

   - Driver fixes for i.MX, single register, Tegra and BayTrail.

   - MAINTAINERS entry for the documentation"

* tag 'pinctrl-v4.7-3' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl:
  pinctrl: baytrail: Fix mingled clock pins
  MAINTAINERS: belong Documentation/pinctrl.txt properly
  pinctrl: tegra: Fix build dependency
  gpio: tegra: Make lockdep class file-scoped
  pinctrl: single: Fix missing flush of posted write for a wakeirq
  pinctrl: imx: Do not treat a PIN without MUX register as an error

Pull cgroup fixes from Tejun Heo:
 "Three fix patches.  Two are for cgroup / css init failure path.  The
  last one makes css_set_lock irq-safe as the deadline scheduler ends up
  calling put_css_set() from irq context"

* 'for-4.7-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/cgroup:
  cgroup: Disable IRQs while holding css_set_lock
  cgroup: set css->id to -1 during init
  cgroup: remove redundant cleanup in css_create

Merge tag 'mac80211-for-davem-2016-06-29-v2' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211

Johannes Berg says:

====================
Just two small fixes
 * fix mesh peer link counter, decrement wasn't always done at all
 * fix ethertype (length) for packets without RFC 1042 or bridge
   tunnel header
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Jeff Kirsher says:

====================
40GbE Intel Wired LAN Driver Updates 2016-06-27

This series contains updates to i40e and i40evf only.

Mitch provides several changes, first adds functions to enable and disable
VSI on a VEB, which allows for configuration of limited promiscuous mode
specifically for bridging purposes.  Sets the RSS Hash Enable registers by
default now that VF RSS is configured by the PF driver.  Fixed a issue
where we could overflow the buffer, by checking the address count and bail
out of the loop at the appropriate time.  Removed the need for a reset
when the device enters limited promiscuous mode, since this was causing
heartburn for people who were using VFs and bridging.

Catherine adds a call to set the client interface down when we put the VSI
down.  Fixed an issue where RSS queues was being limited to the number
of CPUs, so if a user wants to use more queues than CPUs, we want to
trust they know what they are doing and let them.

Greg cleans up the driver suspend routine to ensure we are calling
synchronize_irq() before freeing IRQ vectors and explicitly free the other
causes interrupt resources and shut down the MSIX interrupt.

Serey fixes i40e_set_settings() to not fail when a Direct Attach (DA)
cable is used.

Avinash fixes a supported link bug by removing code which was not allowing
100BaseT to show up in the supported link modes for 10GBaseT PHYs.

Shannon adds a bit of information to the error messages to help determine
the source of error by adding VSI info to macaddr messages.

Tushar Dave fixes error received when turning off TSO on some systems,
which was caused by enabling FD_SB without checking availability of
MSIx vectors, so add the check.

Neerav fixes a possible panic when LLDP/DCBX change happens and the
driver tried to notify the client(s) for each of the PF VSIs, which would
panic when it reached a VSI that did not have any netdev associated with
it.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

There are two generics functions phy_ethtool_{get|set}_link_ksettings,
so we can use them instead of defining the same code in the driver.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The private structure contain a pointer to phydev, but the structure
net_device already contain such pointer. So we can remove the pointer
phydev in the private structure, and update the driver to use the
one contained in struct net_device.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Only the first and last netlink message for a particular conntrack are
actually sent. The first message is sent through nf_conntrack_confirm when
the conntrack is committed. The last one is sent when the conntrack is
destroyed on timeout. The other conntrack state change messages are not
advertised.

When the conntrack subsystem is used from netfilter, nf_conntrack_confirm
is called for each packet, from the postrouting hook, which in turn calls
nf_ct_deliver_cached_events to send the state change netlink messages.

This commit fixes the problem by calling nf_ct_deliver_cached_events in the
non-commit case as well.

Fixes: 7f8a436e ("openvswitch: Add conntrack action")
CC: Joe Stringer <joestringer@nicira.com>
CC: Justin Pettit <jpettit@nicira.com>
CC: Andy Zhou <azhou@nicira.com>
CC: Thomas Graf <tgraf@suug.ch>
Signed-off-by: Samuel Gauthier <samuel.gauthier@6wind.com>
Acked-by: Joe Stringer <joe@ovn.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

SPQ doorbell is currently protected with the compilation barrier. Under the
stress scenarios, we may get into a state where (due to the weak ordering)
several ramrod doorbells were written to the BAR with an out-of-order
producer values. Need to change the barrier type to a write barrier to make
sure that the write buffer is flushed after each doorbell.
Signed-off-by: Sudarsana Reddy Kalluru <sudarsana.kalluru@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

If skb_unshare() fails, we call qdisc_drop() with a NULL skb, which
is no longer supported.

Fixes: 520ac30f ("net_sched: drop packets after root qdisc lock is released")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

neigh_xmit() expects to be called inside an RCU-bh read side critical
section, and while one of its two current callers gets this right, the
other one doesn't.

More specifically, neigh_xmit() has two callers, mpls_forward() and
mpls_output(), and while both callers call neigh_xmit() under
rcu_read_lock(), this provides sufficient protection for neigh_xmit()
only in the case of mpls_forward(), as that is always called from
softirq context and therefore doesn't need explicit BH protection,
while mpls_output() can be called from process context with softirqs
enabled.

When mpls_output() is called from process context, with softirqs
enabled, we can be preempted by a softirq at any time, and RCU-bh
considers the completion of a softirq as signaling the end of any
pending read-side critical sections, so if we do get a softirq
while we are in the part of neigh_xmit() that expects to be run inside
an RCU-bh read side critical section, we can end up with an unexpected
RCU grace period running right in the middle of that critical section,
making things go boom.

This patch fixes this impedance mismatch in the callee, by making
neigh_xmit() always take rcu_read_{,un}lock_bh() around the code that
expects to be treated as an RCU-bh read side critical section, as this
seems a safer option than fixing it in the callers.

Fixes: 4fd3d7d9 ("neigh: Add helper function neigh_xmit")
Signed-off-by: David Barroso <dbarroso@fastly.com>
Signed-off-by: Lennert Buytenhek <lbuytenhek@fastly.com>
Acked-by: David Ahern <dsa@cumulusnetworks.com>
Acked-by: Robert Shearman <rshearma@brocade.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Sudarsana Reddy Kalluru says:

====================
qed*: Fix the static checker warnings.

The patch series addresses the static checker warnings introduced by the
earlier patches related to qed/qede coalesce configuration support.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Static checker warnings:
drivers/net/ethernet/qlogic/qede/qede_ethtool.c:435 qede_get_coalesce()
warn: passing casted pointer '&coal->rx_coalesce_usecs' to
'edev->ops->common->get_coalesce()' 32 vs 16.

The u32 pointer is being typecasted to u16 which may fail for big-endian
platforms.

Fixes: d552fa84 ("qede: Add support for coalescing config read/update.")
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Sudarsana Reddy Kalluru <sudarsana.kalluru@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Static checker warnings:
drivers/net/ethernet/qlogic/qed/qed_int.c:2450 qed_init_cau_sb_entry()
warn: always true condition '(cdev->rx_coalesce_usecs <= 255) =>
(0-255 <= 255)'
drivers/net/ethernet/qlogic/qed/qed_int.c:2511 qed_int_cau_conf_sb()
warn: always true condition '(p_hwfn->cdev->rx_coalesce_usecs <= 255)
=> (0-255 <= 255)'
..

The data types for rx/tx_coalesce_usecs should be u16.

Fixes: commit 722003ac ("qed: Add support for coalescing config read/update.")
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Sudarsana Reddy Kalluru <sudarsana.kalluru@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

I've got a bug report about an e1000e interface, where a VLAN interface is
set up on top of it:

$ ip link add link ens1f0 name ens1f0.99 type vlan id 99
$ ip link set ens1f0 up
$ ip link set ens1f0.99 up
$ ip addr add 192.168.99.92 dev ens1f0.99

At this point, I can ping another host on vlan 99, ip 192.168.99.91.
However, if I do the following:

$ ethtool -K ens1f0 rxvlan off

Then no traffic passes on ens1f0.99. It comes back if I toggle rxvlan on
again. I'm not sure if this is actually intended behavior, or if there's a
lack of software VLAN stripping fallback, or what, but things continue to
work if I simply don't call e1000e_vlan_strip_disable() if there are
active VLANs (plagiarizing a function from the e1000 driver here) on the
interface.

Also slipped a related-ish fix to the kerneldoc text for
e1000e_vlan_strip_disable here...
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

There are two generics functions phy_ethtool_{get|set}_link_ksettings,
so we can use them instead of defining the same code in the driver.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The private structure contain a pointer to phydev, but the structure
net_device already contain such pointer. So we can remove the pointer
phydev in the private structure, and update the driver to use the
one contained in struct net_device.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The PDU length of incoming LLC frames is set to the total skb payload size
in __ieee80211_data_to_8023() of net/wireless/util.c which incorrectly
includes the length of the IEEE 802.11 header.

The resulting LLC frame header has a too large PDU length, causing the
llc_fixup_skb() function of net/llc/llc_input.c to reject the incoming
skb, effectively breaking STP.

Solve the problem by properly substracting the IEEE 802.11 frame header size
from the PDU length, allowing the LLC processor to pick up the incoming
control messages.

Special thanks to Gerry Rozema for tracking down the regression and proposing
a suitable patch.

Fixes: 2d1c304c ("cfg80211: add function for 802.3 conversion with separate output buffer")
Cc: stable@vger.kernel.org
Reported-by: Gerry Rozema <gerryr@rozeware.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>

There is a static checker warning here "warn: mask and shift to zero"
and the code sets "ring" to zero every time.  From looking at how
QLCNIC_FETCH_RING_ID() is used in qlcnic_83xx_process_rcv_ring() the
qlcnic_83xx_hndl() should be removed.

Fixes: 4be41e92 ('qlcnic: 83xx data path routines')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Commit dead9f29 ("perf: Fix race in BPF program unregister") moved
destruction of BPF program from free_event_rcu() callback to __free_event(),
which is problematic if used with tail calls: if prog A is attached as
trace event directly, but at the same time present in a tail call map used
by another trace event program elsewhere, then we need to delay destruction
via RCU grace period since it can still be in use by the program doing the
tail call (the prog first needs to be dropped from the tail call map, then
trace event with prog A attached destroyed, so we get immediate destruction).

Fixes: dead9f29 ("perf: Fix race in BPF program unregister")
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Cc: Jann Horn <jann@thejh.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

I made a dumb off-by-one mistake when I added the vlan stats counter
dumping code. The increment should happen before the check, not after
otherwise we miss one entry when we continue dumping.

Fixes: a60c0903 ("bridge: netlink: export per-vlan stats")
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>