As result of deprecation of MSI-X/MSI enablement functions
pci_enable_msix() and pci_enable_msi_block() all drivers
using these two interfaces need to be updated to use the
new pci_enable_msi_range() and pci_enable_msix_range()
interfaces.
Signed-off-by: Alexander Gordeev <agordeev@redhat.com>
Cc: Eli Cohen <eli@mellanox.com>
Cc: linux-rdma@vger.kernel.org
Cc: netdev@vger.kernel.org
Cc: linux-pci@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>

As result of deprecation of MSI-X/MSI enablement functions
pci_enable_msix() and pci_enable_msi_block() all drivers
using these two interfaces need to be updated to use the
new pci_enable_msi_range() and pci_enable_msix_range()
interfaces.
Signed-off-by: Alexander Gordeev <agordeev@redhat.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Amir Vadai <amirv@mellanox.com>
Cc: netdev@vger.kernel.org
Cc: linux-pci@vger.kernel.org
Acked-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

As result of deprecation of MSI-X/MSI enablement functions
pci_enable_msix() and pci_enable_msi_block() all drivers
using these two interfaces need to be updated to use the
new pci_enable_msi_range() and pci_enable_msix_range()
interfaces.
Signed-off-by: Alexander Gordeev <agordeev@redhat.com>
Cc: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Cc: Jesse Brandeburg <jesse.brandeburg@intel.com>
Cc: Bruce Allan <bruce.w.allan@intel.com>
Cc: e1000-devel@lists.sourceforge.net
Cc: netdev@vger.kernel.org
Cc: linux-pci@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>

As result of deprecation of MSI-X/MSI enablement functions
pci_enable_msix() and pci_enable_msi_block() all drivers
using these two interfaces need to be updated to use the
new pci_enable_msi_range() and pci_enable_msix_range()
interfaces.
Signed-off-by: Alexander Gordeev <agordeev@redhat.com>
Cc: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Cc: Jesse Brandeburg <jesse.brandeburg@intel.com>
Cc: Bruce Allan <bruce.w.allan@intel.com>
Cc: e1000-devel@lists.sourceforge.net
Cc: netdev@vger.kernel.org
Cc: linux-pci@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>

As result of deprecation of MSI-X/MSI enablement functions
pci_enable_msix() and pci_enable_msi_block() all drivers
using these two interfaces need to be updated to use the
new pci_enable_msi_range() and pci_enable_msix_range()
interfaces.
Signed-off-by: Alexander Gordeev <agordeev@redhat.com>
Cc: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Cc: Jesse Brandeburg <jesse.brandeburg@intel.com>
Cc: Bruce Allan <bruce.w.allan@intel.com>
Cc: e1000-devel@lists.sourceforge.net
Cc: netdev@vger.kernel.org
Cc: linux-pci@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>

As result of deprecation of MSI-X/MSI enablement functions
pci_enable_msix() and pci_enable_msi_block() all drivers
using these two interfaces need to be updated to use the
new pci_enable_msi_range() and pci_enable_msix_range()
interfaces.
Signed-off-by: Alexander Gordeev <agordeev@redhat.com>
Cc: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Cc: Jesse Brandeburg <jesse.brandeburg@intel.com>
Cc: e1000-devel@lists.sourceforge.net
Cc: netdev@vger.kernel.org
Cc: linux-pci@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>

As result of deprecation of MSI-X/MSI enablement functions
pci_enable_msix() and pci_enable_msi_block() all drivers
using these two interfaces need to be updated to use the
new pci_enable_msi_range() and pci_enable_msix_range()
interfaces.
Signed-off-by: Alexander Gordeev <agordeev@redhat.com>
Cc: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Cc: Jesse Brandeburg <jesse.brandeburg@intel.com>
Cc: e1000-devel@lists.sourceforge.net
Cc: netdev@vger.kernel.org
Cc: linux-pci@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>

As result of deprecation of MSI-X/MSI enablement functions
pci_enable_msix() and pci_enable_msi_block() all drivers
using these two interfaces need to be updated to use the
new pci_enable_msi_range() and pci_enable_msix_range()
interfaces.
Signed-off-by: Alexander Gordeev <agordeev@redhat.com>
Cc: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Cc: Jesse Brandeburg <jesse.brandeburg@intel.com>
Cc: Bruce Allan <bruce.w.allan@intel.com>
Cc: e1000-devel@lists.sourceforge.net
Cc: netdev@vger.kernel.org
Cc: linux-pci@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>

As result of deprecation of MSI-X/MSI enablement functions
pci_enable_msix() and pci_enable_msi_block() all drivers
using these two interfaces need to be updated to use the
new pci_enable_msi_range() and pci_enable_msix_range()
interfaces.
Signed-off-by: Alexander Gordeev <agordeev@redhat.com>
Cc: Sathya Perla <sathya.perla@emulex.com>
Cc: Subbu Seetharaman <subbu.seetharaman@emulex.com>
Cc: Ajit Khaparde <ajit.khaparde@emulex.com>
Cc: netdev@vger.kernel.org
Cc: linux-pci@vger.kernel.org
Acked-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

As result of deprecation of MSI-X/MSI enablement functions
pci_enable_msix() and pci_enable_msi_block() all drivers
using these two interfaces need to be updated to use the
new pci_enable_msi_range() and pci_enable_msix_range()
interfaces.
Signed-off-by: Alexander Gordeev <agordeev@redhat.com>
Cc: Christian Benvenuti <benve@cisco.com>
Cc: Sujith Sankar <ssujith@cisco.com>
Cc: Govindarajulu Varadarajan <govindarajulu90@gmail.com>
Cc: Neel Patel <neepatel@cisco.com>
Cc: netdev@vger.kernel.org
Cc: linux-pci@vger.kernel.org
Acked-by: Govindarajulu Varadarajan <govindarajulu90@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

As result of deprecation of MSI-X/MSI enablement functions
pci_enable_msix() and pci_enable_msi_block() all drivers
using these two interfaces need to be updated to use the
new pci_enable_msi_range() and pci_enable_msix_range()
interfaces.
Signed-off-by: Alexander Gordeev <agordeev@redhat.com>
Cc: Casey Leedom <leedom@chelsio.com>
Cc: netdev@vger.kernel.org
Cc: linux-pci@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>

There is no need to call pci_disable_msix() in case
the previous call to pci_enable_msix() failed
Signed-off-by: Alexander Gordeev <agordeev@redhat.com>
Cc: Casey Leedom <leedom@chelsio.com>
Cc: netdev@vger.kernel.org
Cc: linux-pci@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>

As result of deprecation of MSI-X/MSI enablement functions
pci_enable_msix() and pci_enable_msi_block() all drivers
using these two interfaces need to be updated to use the
new pci_enable_msi_range() and pci_enable_msix_range()
interfaces.
Signed-off-by: Alexander Gordeev <agordeev@redhat.com>
Cc: Dimitris Michailidis <dm@chelsio.com>
Cc: netdev@vger.kernel.org
Cc: linux-pci@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>

As result of deprecation of MSI-X/MSI enablement functions
pci_enable_msix() and pci_enable_msi_block() all drivers
using these two interfaces need to be updated to use the
new pci_enable_msi_range() and pci_enable_msix_range()
interfaces.
Signed-off-by: Alexander Gordeev <agordeev@redhat.com>
Cc: Santosh Raspatur <santosh@chelsio.com>
Cc: netdev@vger.kernel.org
Cc: linux-pci@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>

There is no need to call pci_disable_msix() in case
the previous call to pci_enable_msix() failed
Signed-off-by: Alexander Gordeev <agordeev@redhat.com>
Cc: Santosh Raspatur <santosh@chelsio.com>
Cc: netdev@vger.kernel.org
Cc: linux-pci@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>

As result of deprecation of MSI-X/MSI enablement functions
pci_enable_msix() and pci_enable_msi_block() all drivers
using these two interfaces need to be updated to use the
new pci_enable_msi_range() and pci_enable_msix_range()
interfaces.
Signed-off-by: Alexander Gordeev <agordeev@redhat.com>
Cc: Rasesh Mody <rmody@brocade.com>
Cc: netdev@vger.kernel.org
Cc: linux-pci@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>

As result of deprecation of MSI-X/MSI enablement functions
pci_enable_msix() and pci_enable_msi_block() all drivers
using these two interfaces need to be updated to use the
new pci_enable_msi_range() and pci_enable_msix_range()
interfaces.
Signed-off-by: Alexander Gordeev <agordeev@redhat.com>
Cc: Nithin Nayak Sujir <nsujir@broadcom.com>
Cc: Michael Chan <mchan@broadcom.com>
Cc: netdev@vger.kernel.org
Cc: linux-pci@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>

As result of deprecation of MSI-X/MSI enablement functions
pci_enable_msix() and pci_enable_msi_block() all drivers
using these two interfaces need to be updated to use the
new pci_enable_msi_range() and pci_enable_msix_range()
interfaces.
Signed-off-by: Alexander Gordeev <agordeev@redhat.com>
Cc: Ariel Elior <ariele@broadcom.com>
Cc: netdev@vger.kernel.org
Cc: linux-pci@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>

As result of deprecation of MSI-X/MSI enablement functions
pci_enable_msix() and pci_enable_msi_block() all drivers
using these two interfaces need to be updated to use the
new pci_enable_msi_range() and pci_enable_msix_range()
interfaces.
Signed-off-by: Alexander Gordeev <agordeev@redhat.com>
Cc: Michael Chan <mchan@broadcom.com>
Cc: netdev@vger.kernel.org
Cc: linux-pci@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>

Claudiu Manoil says:

====================
gianfar: Device configuration fixes

This patchset represents the first part of an effort
to solve some old device configuration issues in gianfar,
especially run-time reset and re-configuration problems.
I'm referring to "on-the-fly" configuration of registers
against HW specification, concurrency issues during device
reset / re-configuration operations, and implementing HW
advisories for these operations.

There's also a good deal of code cleanup and refactoring,
and some other (minor) fixes as well.

v2: Remove sysfs stubs w/o replacing them with module
    params (patch 2).
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

gfar_clean_rx_ring() was designed to be called from napi
(rx softirq) context to do the Rx processing. Calling it
from a process context like this is a bug as it will
clearly race with the napi Rx processing.

There's also no point in initializing num_txbdfree since
startup_gfar() already does that, when bringing the device
up again (after reset). Changing num_txbdfree "on-the-fly"
like this is also subject to race conditions.  num_txbdfree
is handled by the Tx processing path and the device reset
procedure.  Also, don't assume that num_rx_queues is always
equal to num_tx_queues.
Signed-off-by: Claudiu Manoil <claudiu.manoil@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

gfar_halt() and gfar_start() are responsible for stopping
and starting the DMA and the Rx/Tx hw rings. They implement
the support for the "graceful Rx/Tx stop/start" hw procedure,
and also disable/enable eTSEC's hw interrupts in the process.

The GRS/GTS procedure requires however to have the RQUEUE/TQUEUE
registers cleared first and to wait for a period of time for the
current frame to pass through the interface (around ~10ms for a
jumbo frame). Only then may the GTS and GRS bits from DMACTRL be
set to shut down the DMA, and finally the Tx_EN and Rx_EN bits in
MACCFG1 may be cleared to disable the Tx/Rx blocks.

The same register programming order applies to start the Rx/Tx:
enabling the RQUEUE/TQUEUE *before* clearing the GRS/GTS bits.

This is a HW recommendation in order to avoid a possible
controller "lock up" during graceful reset.

Cleanup the gfar_halt()/start() prototypes, to take priv instead
of ndev as their purpose is to operate on HW. Enabling the
RQUEUE/TQUEUE in the hw_init() is not needed anymore since
that's the job of gfar_start().
Signed-off-by: Claudiu Manoil <claudiu.manoil@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Throughout the code there are places where the controller's
hw interrupt sources need to get disabled/enabled (masked/
un-masked) all at once.  The recommendation for disabling
the interrupts is to clear the ievent first then the imask
register (not the other way around).
Use the gfar_ints_enable/disable() helpers to make these
operations consistent.
Signed-off-by: Claudiu Manoil <claudiu.manoil@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The RCTRL updates of the FSL_GIANFAR_DEV_HAS_PADDING device
flag get overriden by the FSL_GIANFAR_DEV_HAS_TIMER flag
settings, which impose a Rx padding alignment of 8 bytes.
As all the eTSEC devices that set HAS_PADDING also set the
HAS_TIMER flag, the HAS_PADDING flag is now obsolete.
Signed-off-by: Claudiu Manoil <claudiu.manoil@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Removing the sysfs stubs for the Tx FIFOCFG and ATTRELI
(stashing) config registers, as these registers may only
be configured after a MAC reset, with the controller stopped
(i.e. during hw init, at probe() time).  The current sysfs
stubs allow on-the-fly updates of these registers (the locking
measures are useless and only add unecessary code).

Changing these registers is discouraged. Only the default values
will be used instead.

Moreover, the stashing (ATTRELI) configuration options were
effectively disabled (didn't get to the hw anyway if changed)
because the stashing device_flags (HAS_BD_STASHING|HAS_BUF_STASHING)
were "accidentally" cleared during probe().
Signed-off-by: Claudiu Manoil <claudiu.manoil@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Factor out gfar_hw_init() to contain all the controller hw
initialization steps for a better control of register writes,
and to significantly simplify the tangled code from gfar_probe().
This results in code size and stack usage reduction (besides
code readability).

Fix memory leak on device removal, by freeing the rx_/tx_queue
structures.

Replace custom bit swapping function with a library one (bitrev8).

Move allocation of rx_/tx_queue struct arrays before the group
structure init, because in order to assign Rx/Tx queues
to groups we need to have the queues first.  This also allows
earlier bail out of gfar_probe(), in case the memory allocation
fails.

The flow control checks for maccfg1 were removed from gfar_probe(),
since flow control is disabled at probe time (priv->rx_/tx_pause_en
are 0). Redundant initializations (by 0) also removed.
Signed-off-by: Claudiu Manoil <claudiu.manoil@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

linux/sctp.h was included twice.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Wang Yufen <wangyufen@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Wang Yufen <wangyufen@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Wang Yufen <wangyufen@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

ERROR: spaces required and "(foo*)" should be "(foo *)"
Signed-off-by: Wang Yufen <wangyufen@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Replace two magic numbers which intialize clgstate::state.
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Phoebe Buckheister says:

====================
ieee802154: support rf212 and extended mac features

this patch set adds support for the RF212 radio chip to the existing
at86rf230 driver and adds support for numerous features of the RF212
chips to the ieee802154 stack. These features include CSMA parameter
configuration, transmit power control, CCA parameter configuration, and
automatic retransmission of frames. Netlink APIs are provided for all
new options introduced in this set.

Many features might also work for RF230, but since I have no such chips
at my disposal, most new features are implemented only for RF212.

Changes since v2:
 * Indentation
Changes since v1:
 * CodingStyle compliance. Thanks Sergei Shtylyov
 * Add CSMA parameters to netlink phy list that were forgotten in v1
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch does multiple things:

 * add .set_csma_params and .set_frame_retries for the RF212 radio.
   This should work fine with RF230, but since I have no RF230 radios to
   test with, RF230 does not implement these right now
 * enable TX_ARET for frame retransmission limits greater than -1

Since RF230 has no operations to change CSMA parameters or frame retry
limits, RF230 will not be able to enter TX_ARET with this patch.
Signed-off-by: Phoebe Buckheister <phoebe.buckheister@itwm.fraunhofer.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

Introduce new netlink attributes for SET_PHY_ATTRS:
 * CSMA minimal backoff exponent
 * CSMA maximal backoff exponent
 * CSMA retry limit
 * frame retransmission limit

The CSMA attributes shall correspond to minBE, maxBE and maxCSMABackoffs of
802.15.4, respectively. The frame retransmission shall correspond to
maxFrameRetries of 802.15.4, unless given as -1: then the old behaviour
of the stack shall apply. For RF2xy, the old behaviour is to not do
channel sensing at all and simply send *right now*, which is not
intended behaviour for most applications and actually prohibited for
some channel/page combinations.

For all values except frame retransmission limit, the defaults of
802.15.4 apply. Frame retransmission limits are set to -1 to indicate
backward-compatible behaviour.
Signed-off-by: Phoebe Buckheister <phoebe.buckheister@itwm.fraunhofer.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

A documented erratum of the RF212 chip describes that some versions of
RF212 may not be properly reset by the standard reset procedure. The
described workaround seems to not fully work either; my RF212 chips will
not correctly receive any frames unless they are taken from RX mode to
TRX_OFF and back to RX mode, effectively forcing a up-down-up-cycle.
Going to TRX_OFF and to RX without intermediate state changes at least
once fixes this.

The same transition is allowed for RF230, so simply do it all the time.
Signed-off-by: Phoebe Buckheister <phoebe.buckheister@itwm.fraunhofer.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

Since three of the four clear channel assesment modes make use of energy
detection, provide an API to set the energy detection threshold.
Driver support for this is available in at86rf230 for the RF212 chips.
Since for these chips the minimal energy detection threshold depends on
page and channel used, add a field to struct at86rf230_local that stores
the minimal threshold. Actual ED thresholds are configured as offsets
from this value.

For RF212, setting the ED threshold will not work before a channel/page
has been set due to the dependency of energy detection in the chip and
the actual channel/page selected.
Signed-off-by: Phoebe Buckheister <phoebe.buckheister@itwm.fraunhofer.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

The standard describes four modes of clear channel assesment: "energy
above threshold", "carrier found", and the logical and/or of these two.
Support for CCA mode setting is included in the at86rf230 driver,
predicated for RF212 chips.
Signed-off-by: Phoebe Buckheister <phoebe.buckheister@itwm.fraunhofer.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

Listen-before-talk is an alternative to CSMA in uncoordinated networks
and prescribed by european regulations if one wants to have a device
with radio duty cycles above 10% (or less in some bands). Add a phy
property to enable/disable LBT in the phy, including support in the
at86rf230 driver for RF212 chips.
Signed-off-by: Phoebe Buckheister <phoebe.buckheister@itwm.fraunhofer.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

The standard assigns channel 0 on page 2 to be 100kbps QPSK in the
868.3MHz band. Add support to the at86rf230 driver for this channel and
page, at the moment predicated only for the RF212 chip.

Per the datasheet, configurations for page 0, channels 0 to 10 and page
2, channels 0 to 10 differ only in the BPSK_QPSK bit. Support for
channels 1 to 10 is untested.
Signed-off-by: Phoebe Buckheister <phoebe.buckheister@itwm.fraunhofer.de>
Signed-off-by: David S. Miller <davem@davemloft.net>