- 11 Jan, 2016 10 commits
-
-
Xing Zheng authored
On the RK3066/RK3188, there was fixed GRF offset configuration to set emac and fixed DIV2 mac TX/RX clock. So, we need to easily set and fit to other SoCs (RK3036) which maybe have different GRF offset, and need adjust mac TX/RX clock. Signed-off-by: Xing Zheng <zhengxing@rock-chips.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Xing Zheng authored
After enter arc_emac_probe, emac will get_phy_id, phy_poll_reset and other connecting PHY via mdiobus_read, so we need to set correct ref clock rate for emac before probe emac. Signed-off-by: Xing Zheng <zhengxing@rock-chips.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
David S. Miller authored
Michael Chan says: ==================== bnxt_en: Zero pad fw messages and add fw reset. 2 patches related to firmware for net-next. ==================== Signed-off-by: David S. Miller <davem@davemloft.net>
-
Rob Swindell authored
Use HWRM_FW_RESET command to request a self-reset of the embedded processor(s) after successfully applying a firmware update. For boot processor, the self-reset is currently deferred until the next PCIe reset. Signed-off-by: Rob Swindell <swindell@broadcom.com> Signed-off-by: Michael Chan <mchan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Michael Chan authored
For future compatibility, zero pad all messages that the driver sends to the firmware to 128 bytes. If these messages are extended in the future with new byte enables, zero padding these messages now will guarantee future compatibility. Signed-off-by: Michael Chan <mchan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Daniel Borkmann authored
This work adds a generalization of the ingress qdisc as a qdisc holding only classifiers. The clsact qdisc works on ingress, but also on egress. In both cases, it's execution happens without taking the qdisc lock, and the main difference for the egress part compared to prior version of [1] is that this can be applied with _any_ underlying real egress qdisc (also classless ones). Besides solving the use-case of [1], that is, allowing for more programmability on assigning skb->priority for the mqprio case that is supported by most popular 10G+ NICs, it also opens up a lot more flexibility for other tc applications. The main work on classification can already be done at clsact egress time if the use-case allows and state stored for later retrieval f.e. again in skb->priority with major/minors (which is checked by most classful qdiscs before consulting tc_classify()) and/or in other skb fields like skb->tc_index for some light-weight post-processing to get to the eventual classid in case of a classful qdisc. Another use case is that the clsact egress part allows to have a central egress counterpart to the ingress classifiers, so that classifiers can easily share state (e.g. in cls_bpf via eBPF maps) for ingress and egress. Currently, default setups like mq + pfifo_fast would require for this to use, for example, prio qdisc instead (to get a tc_classify() run) and to duplicate the egress classifier for each queue. With clsact, it allows for leaving the setup as is, it can additionally assign skb->priority to put the skb in one of pfifo_fast's bands and it can share state with maps. Moreover, we can access the skb's dst entry (f.e. to retrieve tclassid) w/o the need to perform a skb_dst_force() to hold on to it any longer. In lwt case, we can also use this facility to setup dst metadata via cls_bpf (bpf_skb_set_tunnel_key()) without needing a real egress qdisc just for that (case of IFF_NO_QUEUE devices, for example). The realization can be done without any changes to the scheduler core framework. All it takes is that we have two a-priori defined minors/child classes, where we can mux between ingress and egress classifier list (dev->ingress_cl_list and dev->egress_cl_list, latter stored close to dev->_tx to avoid extra cacheline miss for moderate loads). The egress part is a bit similar modelled to handle_ing() and patched to a noop in case the functionality is not used. Both handlers are now called sch_handle_ingress() and sch_handle_egress(), code sharing among the two doesn't seem practical as there are various minor differences in both paths, so that making them conditional in a single handler would rather slow things down. Full compatibility to ingress qdisc is provided as well. Since both piggyback on TC_H_CLSACT, only one of them (ingress/clsact) can exist per netdevice, and thus ingress qdisc specific behaviour can be retained for user space. This means, either a user does 'tc qdisc add dev foo ingress' and configures ingress qdisc as usual, or the 'tc qdisc add dev foo clsact' alternative, where both, ingress and egress classifier can be configured as in the below example. ingress qdisc supports attaching classifier to any minor number whereas clsact has two fixed minors for muxing between the lists, therefore to not break user space setups, they are better done as two separate qdiscs. I decided to extend the sch_ingress module with clsact functionality so that commonly used code can be reused, the module is being aliased with sch_clsact so that it can be auto-loaded properly. Alternative would have been to add a flag when initializing ingress to alter its behaviour plus aliasing to a different name (as it's more than just ingress). However, the first would end up, based on the flag, choosing the new/old behaviour by calling different function implementations to handle each anyway, the latter would require to register ingress qdisc once again under different alias. So, this really begs to provide a minimal, cleaner approach to have Qdisc_ops and Qdisc_class_ops by its own that share callbacks used by both. Example, adding qdisc: # tc qdisc add dev foo clsact # tc qdisc show dev foo qdisc mq 0: root qdisc pfifo_fast 0: parent :1 bands 3 priomap 1 2 2 2 1 2 0 0 1 1 1 1 1 1 1 1 qdisc pfifo_fast 0: parent :2 bands 3 priomap 1 2 2 2 1 2 0 0 1 1 1 1 1 1 1 1 qdisc pfifo_fast 0: parent :3 bands 3 priomap 1 2 2 2 1 2 0 0 1 1 1 1 1 1 1 1 qdisc pfifo_fast 0: parent :4 bands 3 priomap 1 2 2 2 1 2 0 0 1 1 1 1 1 1 1 1 qdisc clsact ffff: parent ffff:fff1 Adding filters (deleting, etc works analogous by specifying ingress/egress): # tc filter add dev foo ingress bpf da obj bar.o sec ingress # tc filter add dev foo egress bpf da obj bar.o sec egress # tc filter show dev foo ingress filter protocol all pref 49152 bpf filter protocol all pref 49152 bpf handle 0x1 bar.o:[ingress] direct-action # tc filter show dev foo egress filter protocol all pref 49152 bpf filter protocol all pref 49152 bpf handle 0x1 bar.o:[egress] direct-action A 'tc filter show dev foo' or 'tc filter show dev foo parent ffff:' will show an empty list for clsact. Either using the parent names (ingress/egress) or specifying the full major/minor will then show the related filter lists. Prior work on a mqprio prequeue() facility [1] was done mainly by John Fastabend. [1] http://patchwork.ozlabs.org/patch/512949/Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Acked-by: John Fastabend <john.r.fastabend@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Andrew Lunn authored
The warning about being able to read any MDIO device, not just the attached ethernet devices PHY applies to all MDIO drivers. So remove it. This also removes a reference to a member in phy_device which has moved. Signed-off-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Andrew Lunn authored
Fix a number of build errors due to moving the phy_map and centralizing interrupt allocation. Signed-off-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Guenter Roeck authored
Use phy_find_first() to find the first phy device instead of open coding it. Cc: Andrew Lunn <andrew@lunn.ch> Signed-off-by: Guenter Roeck <linux@roeck-us.net> Acked-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Guenter Roeck authored
Commit 7f854420 ("phy: Add API for {un}registering an mdio device to a bus") introduces an API to access mii_bus structures, but missed to update the sb1250 driver. This results in the following build error. drivers/net/ethernet/broadcom/sb1250-mac.c: In function 'sbmac_mii_probe': drivers/net/ethernet/broadcom/sb1250-mac.c:2360:24: error: 'struct mii_bus' has no member named 'phy_map' Use phy_find_first() instead of open coding it. Commit 2220943a ("phy: Centralise print about attached phy") introduces the following build error. drivers/net/ethernet/broadcom/sb1250-mac.c: In function 'sbmac_mii_probe': drivers/net/ethernet/broadcom/sb1250-mac.c:2383:20: error: 'phydev' undeclared Fixes: 7f854420 ("phy: Add API for {un}registering an mdio device to a bus") Fixes: 2220943a ("phy: Centralise print about attached phy") Cc: Andrew Lunn <andrew@lunn.ch> Signed-off-by: Guenter Roeck <linux@roeck-us.net> Acked-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
-
- 10 Jan, 2016 24 commits
-
-
David S. Miller authored
Andrew Lunn says: ==================== Fix breakage from mdio device These two patches fix MIPS platforms which got broken by the recent mdio device patchset. ==================== Signed-off-by: David S. Miller <davem@davemloft.net>
-
Andrew Lunn authored
The mdio device patches moved the bus member in phy_device into a substructure. This driver got missed. Fix it. Signed-off-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Andrew Lunn authored
Make use of the helper to find the first phy device. This also fixes the compile breakage. Signed-off-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Romain Perier authored
Originally, most of the platforms using this driver did not define an mdio subnode in the devicetree. Commit e34d65 ("stmmac: create of compatible mdio bus for stmmac driver") introduced a backward compatibily issue by using of_mdiobus_register explicitly with an mdio subnode. This patch fixes the issue by calling the function mdiobus_register, when mdio subnode is not found. The driver is now compatible with both modes. Fixes: e34d6569 ("stmmac: create of compatible mdio bus for stmmac driver") Signed-off-by: Romain Perier <romain.perier@gmail.com> Tested-by: Phil Reid <preid@electromag.com.au> Signed-off-by: David S. Miller <davem@davemloft.net>
-
David S. Miller authored
Daniel Borkmann says: ==================== BPF update Fixes a csum issue on ingress. As mentioned previously, net-next seems just fine imho. Later on, will follow up with couple of replacements like ovs_skb_postpush_rcsum() etc. Thanks! v1 -> v2: - Added patch 1 with helper - Implemented Hannes' idea to just use csum_partial, thanks! ==================== Signed-off-by: David S. Miller <davem@davemloft.net>
-
Daniel Borkmann authored
Add a small helper skb_postpush_rcsum() and fix up redirect locations that need CHECKSUM_COMPLETE fixups on ingress. dev_forward_skb() expects a proper csum that covers also Ethernet header, f.e. since 2c26d34b ("net/core: Handle csum for CHECKSUM_COMPLETE VXLAN forwarding"), we also do skb_postpull_rcsum() after pulling Ethernet header off via eth_type_trans(). When using eBPF in a netns setup f.e. with vxlan in collect metadata mode, I can trigger the following csum issue with an IPv6 setup: [ 505.144065] dummy1: hw csum failure [...] [ 505.144108] Call Trace: [ 505.144112] <IRQ> [<ffffffff81372f08>] dump_stack+0x44/0x5c [ 505.144134] [<ffffffff81607cea>] netdev_rx_csum_fault+0x3a/0x40 [ 505.144142] [<ffffffff815fee3f>] __skb_checksum_complete+0xcf/0xe0 [ 505.144149] [<ffffffff816f0902>] nf_ip6_checksum+0xb2/0x120 [ 505.144161] [<ffffffffa08c0e0e>] icmpv6_error+0x17e/0x328 [nf_conntrack_ipv6] [ 505.144170] [<ffffffffa0898eca>] ? ip6t_do_table+0x2fa/0x645 [ip6_tables] [ 505.144177] [<ffffffffa08c0725>] ? ipv6_get_l4proto+0x65/0xd0 [nf_conntrack_ipv6] [ 505.144189] [<ffffffffa06c9a12>] nf_conntrack_in+0xc2/0x5a0 [nf_conntrack] [ 505.144196] [<ffffffffa08c039c>] ipv6_conntrack_in+0x1c/0x20 [nf_conntrack_ipv6] [ 505.144204] [<ffffffff8164385d>] nf_iterate+0x5d/0x70 [ 505.144210] [<ffffffff816438d6>] nf_hook_slow+0x66/0xc0 [ 505.144218] [<ffffffff816bd302>] ipv6_rcv+0x3f2/0x4f0 [ 505.144225] [<ffffffff816bca40>] ? ip6_make_skb+0x1b0/0x1b0 [ 505.144232] [<ffffffff8160b77b>] __netif_receive_skb_core+0x36b/0x9a0 [ 505.144239] [<ffffffff8160bdc8>] ? __netif_receive_skb+0x18/0x60 [ 505.144245] [<ffffffff8160bdc8>] __netif_receive_skb+0x18/0x60 [ 505.144252] [<ffffffff8160ccff>] process_backlog+0x9f/0x140 [ 505.144259] [<ffffffff8160c4a5>] net_rx_action+0x145/0x320 [...] What happens is that on ingress, we push Ethernet header back in, either from cls_bpf or right before skb_do_redirect(), but without updating csum. The "hw csum failure" can be fixed by using the new skb_postpush_rcsum() helper for the dev_forward_skb() case to correct the csum diff again. Thanks to Hannes Frederic Sowa for the csum_partial() idea! Fixes: 3896d655 ("bpf: introduce bpf_clone_redirect() helper") Fixes: 27b29f63 ("bpf: add bpf_redirect() helper") Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Acked-by: Alexei Starovoitov <ast@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Daniel Borkmann authored
Add a skb_at_tc_ingress() as this will be needed elsewhere as well and can hide the ugly ifdef. Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Acked-by: Alexei Starovoitov <ast@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
-
David S. Miller authored
Nikolay Borisov says: ==================== Namespaceify tcp keepalive machinery The following patch series enables the tcp keepalive mechanism to be configured per net namespace. This is especially useful if you have multiple containers hosted on one node and one of them is under DoS- in such situations one thing which could be done is to configure the tcp keepalive settings such that connections for that particular container are being reset faster. Another scenario where not being able to control those knob comes per container is problematic is occurs the value of net.netfilter.nf_conntrack_tcp_timeout_established is set below the keepalive interval, in such situations the server won't send an RST packet resulting in applications not trying to reconnect and stale connection waiting. Changing the global keepalive value is a possible solution but it might interfere with other containers. The three patches gradually convert each of the affected knobs to be per netns. I thought it would be easier for review than put everything in one patch. If people deem it more appropriate to squash everything in one patch (maybe after review) I'd be more than happy to do it. The patches have been compile-tested on 4.4 and functionally tested on 3.12 and they work as expected. These are based off 4.4-rc8 ==================== Acked-by: "Eric W. Biederman" <ebiederm@xmission.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Nikolay Borisov authored
This is the final part required to namespaceify the tcp keep alive mechanism. Signed-off-by: Nikolay Borisov <kernel@kyup.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Nikolay Borisov authored
This is required to have full tcp keepalive mechanism namespace support. Signed-off-by: Nikolay Borisov <kernel@kyup.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Nikolay Borisov authored
Different net namespaces might have different requirements as to the keepalive time of tcp sockets. This might be required in cases where different firewall rules are in place which require tcp timeout sockets to be increased/decreased independently of the host. Signed-off-by: Nikolay Borisov <kernel@kyup.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
David S. Miller authored
Jiri Pirko says: ==================== mlxsw: Adding layer 2 multicast Elad says: This patchset add Linux hardware reflection for L2 multicast offload and add MC support in mlxsw. For every bridge MDB entry insertion, either by IGMP snooping or by static insertion/removal, a switchdev ops is been called. In mlxsw, a new multicast group (MID) is been created and ports are assigned. When all ports are removed, the multicast group is been deleted. --- v1->v2: - GFP_ATOMIC->GFP_KERNEL change in patch 7/8 ==================== Signed-off-by: David S. Miller <davem@davemloft.net>
-
Elad Raz authored
Signed-off-by: Elad Raz <eladr@mellanox.com> Signed-off-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Elad Raz authored
Add SWITCHDEV_OBJ_ID_PORT_MDB switchdev ops support. On first MDB insertion creates a new multicast group (MID) and add members port to the MID. Also add new MDB entry for the flooding-domain (fid-vid) and link the MDB entry to the newly constructed MC group. Signed-off-by: Elad Raz <eladr@mellanox.com> Signed-off-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: Jiri Pirko <jiri@mellanox.com> Reviewed-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Elad Raz authored
Adding a generic function that translate VID to FID. Signed-off-by: Elad Raz <eladr@mellanox.com> Signed-off-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Elad Raz authored
Signed-off-by: Elad Raz <eladr@mellanox.com> Signed-off-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Elad Raz authored
Adding back SMID register definition and packing. For each MC group a new SMID entry will be generated. Signed-off-by: Elad Raz <eladr@mellanox.com> Signed-off-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Elad Raz authored
Multicast-related records have specific format in SFD register. Signed-off-by: Elad Raz <eladr@mellanox.com> Signed-off-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Elad Raz authored
Offload MDB changes per port to hardware Signed-off-by: Elad Raz <eladr@mellanox.com> Signed-off-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: Jiri Pirko <jiri@mellanox.com> Reviewed-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Elad Raz authored
Define HW multicast entry: MAC and VID. Using a MAC address simplifies support for both IPV4 and IPv6. Signed-off-by: Elad Raz <eladr@mellanox.com> Signed-off-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
git://git.open-mesh.org/linux-mergeDavid S. Miller authored
Antonio Quartulli says: ==================== Included changes: - increase internal module version - increase BLA wait periods to 6 - purge BLA backbone table when it is disabled - make sure post function is invoked only if sysfs value is changed - simplify code by removing useless NULL checks - various corrections to existing kerneldoc - minor cleanups ==================== Signed-off-by: David S. Miller <davem@davemloft.net>
-
Jiri Pirko authored
It may happen that we get notification for FDB entry for object (port, lag, vport), which does not exist. Currently we ignore that, which only causes this being re-sent in next notification. The entry will never disappear. So get rid of it by simply removing it using SFD register. Signed-off-by: Jiri Pirko <jiri@mellanox.com> Reviewed-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Jiri Pirko authored
Do not pass struct mlxsw_sp_port to mlxsw_sp_port_fdb_uc_op and rather just pass local_port. This is needed in case this is called from SFN process function and mlxsw_sp_port is not existent for particular local_port. Signed-off-by: Jiri Pirko <jiri@mellanox.com> Reviewed-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Sudip Mukherjee authored
Modify plip driver to use the new parallel port device model. Signed-off-by: Sudip Mukherjee <sudip@vectorindia.org> Signed-off-by: David S. Miller <davem@davemloft.net>
-
- 09 Jan, 2016 6 commits
-
-
Sven Eckelmann authored
Signed-off-by: Sven Eckelmann <sven@narfation.org> Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch> Signed-off-by: Antonio Quartulli <a@unstable.cc>
-
Sven Eckelmann authored
Signed-off-by: Sven Eckelmann <sven@narfation.org> Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch> Signed-off-by: Antonio Quartulli <a@unstable.cc>
-
Sven Eckelmann authored
Signed-off-by: Sven Eckelmann <sven@narfation.org> Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch> Signed-off-by: Antonio Quartulli <a@unstable.cc>
-
Sven Eckelmann authored
kernel-doc is not able to skip an #ifdef between the kernel documentation block and the start of the struct. Moving the #ifdef before the kernel doc block avoids this problem Signed-off-by: Sven Eckelmann <sven@narfation.org> Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch> Signed-off-by: Antonio Quartulli <a@unstable.cc>
-
Sven Eckelmann authored
Signed-off-by: Sven Eckelmann <sven@narfation.org> Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch> Signed-off-by: Antonio Quartulli <a@unstable.cc>
-
Markus Elfring authored
Let us split a check for a condition at the beginning of the batadv_is_ap_isolated() function so that a direct return can be performed in this function if the variable "vlan" contained a null pointer. Signed-off-by: Markus Elfring <elfring@users.sourceforge.net> Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch> Signed-off-by: Antonio Quartulli <a@unstable.cc>
-