Add rudimentary support for Thumb ptracing; we aren't able to single
step through thumb branches yet, but this change provides enough
infrastructure to make this possible.

This cset updates (as much as is possible) the NCR5380-based Acorn
SCSI drivers, mainly converting them to the new error handling code.
However, they still don't build due to errors in NCR5380.

Vojtech has patches that bring their counterparts in the input
subsystem up to date (and into a working state) so these drivers
are no longer required.

This cset also fixes the Acorn i2c RTC code.

This cset combines the Atomwide and The Serial Port 16550 driver
modules into one "8250_acorn.c" driver.  This new module takes full
advantage of the LDM-based expansion card facilities.

This cset implements validity checks on the ethernet MAC address when
the device is opened, and refuses to open the device if this check
fails.  We also provide the set_mac_address method to allow ifconfig
to change the mac address to something valid.

In addition, the driver is converted from the old expansion card
discovery methods to the new device model driver framework.

Provide LDM-based driver registration/removal interface for drivers
to use.  We make the old device discovery code ignore devices
claimed via the LDM framework.  However, the LDM framework ignores
devices that may be in use by the old device discovery code.  This
is fine since the only devices that will still use the old discovery
code will be SCSI drivers.

Currently, we don't provide a useful dev.name entry.

This updates the Integrator cpufreq code to use the new interfaces,
and makes the sa1100 cpufreq round up the requested frequency.

The second serial port is never present in these machines, so its
pointless listing it in the first place.

- ide_register_hw takes two arguments, not one.
- ide_fix_driveid is no longer used.

This adds ARM support for in_atomic() and asm/numnodes.h

This updates these neponset and sa1111 support to use the new system
device infrastructure in the Linux device model.

Sanitise includes of asm/tlbflush.h, asm/cacheflush.h, asm/proc-fns.h
Implement ARM-specific TLB "shootdown" code.  It turns out that it
is overall more efficient to unconditionally invalidate the whole
TLB rather than entry by entry when removing areas.

This cset fixes the RiscPC decompressor code for the PIC changes.

We use a pointer to a structure rather than a structure to access
params.  With a PIC decompressor, the address of the structure gets
PIC-ified which is not what we want.

Update pcibios_enable_device to only enable requested resources,
mainly for IDE.  Supply a pci_mmap_page_range() function to allow
user space to mmap PCI regions.

This updates the ARM time keeping functions to use tick_nsec/1000
instead of tick.

To keep the Config.in files relatively clean, we use the
following construct:

 if [ "$CONFIG_ARM" = "y" ]; then
    dep_tristate 'Foo' CONFIG_FOO $CONFIG_BAR
 fi

where CONFIG_BAR is some machine implementation or high-level
chip support configuration option.  If CONFIG_BAR is left
empty, then the tristate is offered to the user, which isn't
what we want.  Defining CONFIG_BAR to 'n' prevents the option
being offered.

This is a rule I generally try to implement within
arch/arm/config.in.

This cset makes CONFIG_SA1111 and CONFIG_ARM_THUMB behave that
way.

Since the decompressor supports PIC, even for CONFIG_ZBOOT_ROM,
we can easily allow an image which has been linked to run at
a particular address in ROM to be moved to RAM.  We just need
to make sure that we don't relocate the GOT entries for the
BSS segment.

This cset also implements sa1100-based debugging for the
decompressor.

These two variables are used by more than just the linker;
they're also used by head.S to know where it can safely
place the page tables.  We therefore need to export it
from the Makefile.

These are also highly machine dependent; we don't want
to duplicate the same set of conditionals for cpp and
for the makefiles.

arch/arm/Makefile also contained a stray close-paren.  I'm
submitting this one to the lost property office.

We also always pass -mno-fpu to the assember; this
guarantees that any floating point will be caught.

SPARC was unconditionally setting CONFIG_SERIAL_CORE_CONSOLE to y
and conditionally setting CONFIG_SERIAL_CORE depending on the Sparc
sub-drivers.  In addition, the core serial driver for SPARC is
always built, so we end up with link errors.

We instead make CONFIG_SERIAL_CORE{,_CONSOLE} dependent on building
the SPARC core driver (CONFIG_SERIAL_SUNCORE).

uses fields that do not exist otherwise.

Due to some bugs in byteorder/generic.h linux would always use C handcoded
swab64 for 64bit ntohq or cpu_to_be64.  The C version is very inefficient
and expands to 30+ instructions of horrible code.

This hurts on filesystems that use on disk big endian data structures
with 64bit data types.

This patch adds an assembly optimized swab64 to fix it. Now bswab64 is
4 instructions when your CPU supports bswap and 9 when it doesn't.
Tests were done with gcc 3.2, may be different on older gcc.

This is good for ~600 bytes code size reduction in XFS (gcc 3.2):
Before:
 503199    3296    1682  508177   7c111 fs/xfs/xfs.o
After:
 502543    3296    1682  507521   7be81 fs/xfs/xfs.o

Also should be faster.

Also some minor cleanups in the file.

into home.transmeta.com:/home/torvalds/v2.5/linux

Most of these changes have been tested and used in the 2.4 tree, so this
is mostly a forward port of 2.4 bugfixes.

* C99 initializers
* Added specific initializations instead of assuming that the private
  part of the inode is already initialized.
* Remove unused code.
* Moved container file to the struct file private data, this is to
* correct the session semantics model when file updates are fetched from
* the server (old 'sessions' shouldn't see the new container yet).
* Fixed consistency (and occasional oopes) when mmap-ing Coda files.
* Fixing up inode numbers in readdir, old libc5 getcwd was broken.
* Nuked upcall_stats, all of this can easily be maintained in userspace,
  and the existing code suffers from overflows in the fixed point
  calculations.

- Fix some printk warnings in 3c59x.c (inl() now returns a long).

- ext3 warning fix from Stephen Hemminger: "__FUNCTION__ is a
  constant and gcc warns about passing it as a mutuable string."

- Fix a return-with-BKL-held in isofs_readdir()

- paride 64-bit sector_t fix (Bill Irwin)

into home.transmeta.com:/home/torvalds/v2.5/linux

This syncs up the cyclone-timer code w/ Greg's changes from this
morning.

In the current kernels, when a PCMCIA card is inserted into or
removed from a socket, the kernel oopses because yenta_bh() tries to
dereference a NULL pointer.

The attached patch initialises the argument to yenta_bh() so that this
doesn't happen.

into home.transmeta.com:/home/torvalds/v2.5/linux

into home.transmeta.com:/home/torvalds/v2.5/linux

Add _request and _parse methods for nfsd.fh and
nfsd.exports tables.

nfsd.fh maps a filehandle-fragment to a path for a client,
and nfsd.exports maps a path to export options for a client.

a message should be:
   nfsd 10.0.1.1 {Expirydate}  domainname

if domainname is empty, then this is a NEGATIVE entry: that
IP address will be deined access.

{Expirydate} is seconds since unix epoch.
e.g.  1036105199 for midnight, halloween.

get_word understands both \x and \012 quoting styles.

This is the first upcall to actually be coded.
A request will look like:
   nfsd 127.0.0.1

This code enhances 'cache_check' to try to initiate
an up-call if the cache entry is not up-to-date, and also
defines add_word and add_hex for formating up-call
requests.  See rpc-cache.txt for more detail.

[PATCH] kNFSd: Create files: /proc/net/rpc/$CACHENAME/channel for communicating cache updates with kernel

Each cache gets it's own 'channel' at
  /proc/net/rpc/$CACHENAME/channel

Reads from the file will return all pending requests, one at a time.
select will block when at end of file.
writes will pass full lines in to be processed.