Jiri Benc says:

====================
nsh: headers, GSO

This adds header structs and helpers for NSH together with GSO support.

Note there is no code in this patchset that actually manipulates the NSH
headers. That was sent to netdev by Yi Yang ("[PATCH net-next v6 0/3]
openvswitch: add NSH support"). The aim of this series is to lay the
groundwork and ease the implementation for him.

In addition to openvswitch, the NSH support should be added to tc (flower to
match, act_nsh to push/pop NSH headers). That will come later. There's
currently no plan to support NSH by other means than those two.

The patch 3 in this patchset was written by Yi Yang, I took it from the
aforementioned series and slightly modified it - see the note in the patch.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Add a new nsh/ directory. It currently holds only GSO functions but more
will come: in particular, code shared by openvswitch and tc to manipulate
NSH headers.

For now, assume there's no hardware support for NSH segmentation. We can
always introduce netdev->nsh_features later.
Signed-off-by: Jiri Benc <jbenc@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

NSH (Network Service Header)[1] is a new protocol for service
function chaining, it can be handled as a L3 protocol like
IPv4 and IPv6, Eth + NSH + Inner packet or VxLAN-gpe + NSH +
Inner packet are two typical use cases.

This patch adds NSH header structures and helpers for NSH GSO
support and Open vSwitch NSH support.

[1] https://datatracker.ietf.org/doc/draft-ietf-sfc-nsh/

[Jiri: added nsh_hdr() helper and renamed the header struct to "struct
nshhdr" to match the usual pattern. Removed packet type defines, these are
now shared with VXLAN-GPE.]
Signed-off-by: Yi Yang <yi.y.yang@intel.com>
Signed-off-by: Jiri Benc <jbenc@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The values are shared between VXLAN-GPE and NSH. Originally probably by
coincidence but I notified both working groups about this last year and they
seem to keep the values in sync since then.

Hopefully they'll get a single IANA registry for the values, too. (I asked
them for that.)

Factor out the code to be shared by the NSH implementation.

NSH and MPLS values are added in this patch, too. For MPLS, the drafts
incorrectly assign only a single value, while we have two MPLS ethertypes.
I raised the problem with both groups. For now, I assume the value is for
unicast.
Signed-off-by: Jiri Benc <jbenc@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The NSH draft says:

   An IEEE EtherType, 0x894F, has been allocated for NSH.
Signed-off-by: Jiri Benc <jbenc@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Alexander Aring says:

====================
tc: act_ife: handle IEEE IFE ethertype as default

this patch series will introduce the IFE ethertype which is registered by
IEEE. If the netlink act_ife type netlink attribute is not given it will
use this value by default now.
At least it will introduce some UAPI testcases to check if the default type
is used if not specified and vice versa.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch adds a new testcase for the IFE type setting in tc. In case
of user specified the type it will check if the ife is correctly
configured to react on it. If it's not specified the default IFE type
should be used.
Signed-off-by: Alexander Aring <aring@mojatatu.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch handles a default IFE type if it's not given by user space
netlink api. The default IFE type will be the registered ethertype by
IEEE for IFE ForCES.
Signed-off-by: Alexander Aring <aring@mojatatu.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch adds the forces IFE lfb type according to IEEE registered
ethertypes. See http://standards-oui.ieee.org/ethertype/eth.txt for more
information. Since there exists the IFE subsystem it can be used there.

This patch also use the correct word "ForCES" instead of "FoRCES" which
is a spelling error inside the IEEE ethertype specification.
Signed-off-by: Alexander Aring <aring@mojatatu.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Explain that the patch queue in patchwork should not be touched by patch
submitters.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Tariq Toukan says:

====================
mlx4 misc patches

This patchset contains misc patches from the team
to the mlx4 Core and Eth drivers.

Patch 1 by Eran replaces large static allocations by dynamic ones.
Patch 2 by Leon makes an explicit conversion and solves a smatch warning.
In patch 3 I fix a misplaced brackets of the sizeof operation.
Patch 4 by Moshe adds the ability to inform the FW regarding user mac updates.

Series generated against net-next commit:
901c5d2f ARM: dts: rk3228-evb: Fix the compiling error
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Adding support for updating the FW on new port mac, when port mac change
is requested by the user. This info is required by the FW as OEM
management tools require this info directly from the NIC FW.
Check device capability bit to verify the FW supports user mac.
If the FW does support it, use set_port command to notify the FW on the
new mac.
The feature is relevant only to PF port mac.
Signed-off-by: Moshe Shemesh <moshe@mellanox.com>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When changing the sizeof style usage in the patch cited below,
one brackets misplacement was introduced. Here we fix it.

Fixes: 31975e27 ("mlx4: sizeof style usage")
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Cc: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

The "lg" variable is declared as int so in all places where this variable
is used as a shift operand, the output will be int too.

This produces the following smatch warning:
drivers/net/ethernet/mellanox/mlx4/fw.c:1532 mlx4_map_cmd() warn:
	should '1 << lg' be a 64 bit type?

Simple declaration of "1" to be "1ULL" will fix the issue.

Fixes: 225c7b1f ("IB/mlx4: Add a driver Mellanox ConnectX InfiniBand adapters")
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In order to avoid temporary large structs on the stack,
allocate them dynamically.
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: Tal Alon <talal@mellanox.com>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

A few useful tracepoints to trace bridge forwarding
database updates.
Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Florian Fainelli says:

====================
Endian fixes for SYSTEMPORT/SF2/MDIO

While trying an ARM BE kernel for kinks, the 3 drivers below started not
working and the reasons why became pretty obvious because the register space
remains LE (hardwired), except for Broadcom MIPS where it follows the CPU's
native endian (let's call that a feature).
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

The driver currently uses __raw_{read,write}l which works for all
platforms supported: Broadcom MIPS LE/BE (native endian), ARM LE (native
endian) but not ARM BE (registers are still LE). Switch to using the
proper accessors for all platforms and explain why Broadcom MIPS BE is
special here, in doing so, we introduce a couple of helper functions to
abstract these differences.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

RSB_SWAP0 needs to match the host CPU endian, and it needs to be set
for LE and clear for BE. RSB_SWAP1 must always be cleared for SYSTEMPORT
Lite.

With these settings, we have the Receive Status Block always match the
host endian and we do not need to perform any conversion. Since there is
not necessarily a CONFIG_CPU_LITTLE_ENDIAN option defined, we test for
!CONFIG_CPU_BIG_ENDIAN which is guaranteed to be set.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The Starfigther 2 driver currently uses __raw_{read,write}l which means
native I/O endian. This works correctly for an ARM LE kernel (default)
but fails miserably on an ARM BE (BE8) kernel where registers are kept
little endian, so replace uses with {read,write}l_relaxed here which is
what we want because this is all performance sensitive code.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The SYSTEMPORT driver currently uses __raw_{read,write}l which means
native I/O endian. This works correctly for an ARM LE kernel (default)
but fails miserably on an ARM BE (BE8) kernel where registers are kept
little endian, so replace uses with {read,write}l_relaxed here which is
what we want because this is all performance sensitive code.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge tag 'wireless-drivers-next-for-davem-2017-08-28' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next

Kalle Valo says:

====================
wireless-drivers-next patches for 4.14

rsi driver is getting a lot of new features lately, but as usual
active development happening on iwlwifi as well as other drivers.

I pulled wireless-drivers to fix multiple conflicts in iwlwifi and to
make it easier further development.

Major changes:

ath10k

* initial UBS bus support (no full support yet)

* add tdls support for 10.4 firmware

ath9k

* add Dell Wireless 1802

wil6210

* support FW RSSI reporting

rsi

* support legacy power save, U-APSD, rf-kill and AP mode

* RTS threshold configuration

brcmfmac

* support CYW4373 SDIO/USB chipset

iwlwifi

* some more code moved to a new directory

* add new PCI ID for 7265D
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

clk_div_table are not supposed to change at runtime.
meson8b_dwmac structure is working with const clk_div_table.
So mark the non-const structs as const.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Jesper Dangaard Brouer says:

====================
XDP redirect tracepoints

I feel this is as far as I can take the tracepoint infrastructure to
assist XDP monitoring.

Tracepoints comes with a base overhead of 25 nanosec for an attached
bpf_prog, and 48 nanosec for using a full perf record. This is
problematic for the XDP use-case, but it is very convenient to use the
existing perf infrastructure.

From a performance perspective, the real solution would be to attach
another bpf_prog (that understand xdp_buff), but I'm not sure we want
to introduce yet another bpf attach API for this.

One thing left is to standardize the possible err return codes, to a
limited set, to allow easier (and faster) mapping into a bpf map.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

This tool xdp_monitor demonstrate how to use the different xdp_redirect
tracepoints xdp_redirect{,_map}{,_err} from a BPF program.

The default mode is to only monitor the error counters, to avoid
affecting the per packet performance. Tracepoints comes with a base
overhead of 25 nanosec for an attached bpf_prog, and 48 nanosec for
using a full perf record (with non-matching filter).  Thus, default
loading the --stats mode could affect the maximum performance.

This version of the tool is very simple and count all types of errors
as one.  It will be natural to extend this later with the different
types of errors that can occur, which should help users quickly
identify common mistakes.

Because the TP_STRUCT was kept in sync all the tracepoints loads the
same BPF code.  It would also be natural to extend the map version to
demonstrate how the map information could be used.
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

For supporting XDP_REDIRECT, a device driver must (obviously)
implement the "TX" function ndo_xdp_xmit().  An additional requirement
is you cannot TX out a device, unless it also have a xdp bpf program
attached. This dependency is caused by the driver code need to setup
XDP resources before it can ndo_xdp_xmit.

Update bpf samples xdp_redirect and xdp_redirect_map to automatically
attach a dummy XDP program to the configured ifindex_out device.  Use
the XDP flag XDP_FLAGS_UPDATE_IF_NOEXIST on the dummy load, to avoid
overriding an existing XDP prog on the device.
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Creating as specific xdp_redirect_map variant of the xdp tracepoints
allow users to write simpler/faster BPF progs that get attached to
these tracepoints.

Goal is to still keep the tracepoints in xdp_redirect and xdp_redirect_map
similar enough, that a tool can read the top part of the TP_STRUCT and
produce similar monitor statistics.
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

There is a need to separate the xdp_redirect tracepoint into two
tracepoints, for separating the error case from the normal forward
case.

Due to the extreme speeds XDP is operating at, loading a tracepoint
have a measurable impact.  Single core XDP REDIRECT (ethtool tuned
rx-usecs 25) can do 13.7 Mpps forwarding, but loading a simple
bpf_prog at the tracepoint (with a return 0) reduce perf to 10.2 Mpps
(CPU E5-1650 v4 @ 3.60GHz, driver: ixgbe)

The overhead of loading a bpf-based tracepoint can be calculated to
cost 25 nanosec ((1/13782002-1/10267937)*10^9 = -24.83 ns).

Using perf record on the tracepoint event, with a non-matching --filter
expression, the overhead is much larger. Performance drops to 8.3 Mpps,
cost 48 nanosec ((1/13782002-1/8312497)*10^9 = -47.74))

Having a separate tracepoint for err cases, which should be less
frequent, allow running a continuous monitor for errors while not
affecting the redirect forward performance (this have also been
verified by measurements).
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Given previous patch expose the map_id, it seems natural to also
report the bpf prog id.
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

To make sense of the map index, the tracepoint user also need to know
that map we are talking about.  Supply the map pointer but only expose
the map->id.

The 'to_index' is renamed 'to_ifindex'.  In the xdp_redirect_map case,
this is the result of the devmap lookup. The map lookup key is exposed
as map_index, which is needed to troubleshoot in case the lookup failed.
The 'to_ifindex' is placed after 'err' to keep TP_STRUCT as common as
possible.

This also keeps the TP_STRUCT similar enough, that userspace can write
a monitor program, that doesn't need to care about whether
bpf_redirect or bpf_redirect_map were used.
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Supplying the action argument XDP_REDIRECT to the tracepoint xdp_redirect
is redundant as it is only called in-case this action was specified.

Remove the argument, but keep "act" member of the tracepoint struct and
populate it with XDP_REDIRECT.  This makes it easier to write a common bpf_prog
processing events.
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

David Howells says:

====================
rxrpc: Miscellany

Here are a number of patches that make some changes/fixes and add a couple
of extensions to AF_RXRPC for kernel services to use.  The changes and
fixes are:

 (1) Use time64_t rather than u32 outside of protocol or
     UAPI-representative structures.

 (2) Use the correct time stamp when loading a key from an XDR-encoded
     Kerberos 5 key.

 (3) Fix IPv6 support.

 (4) Fix some places where the error code is being incorrectly made
     positive before returning.

 (5) Remove some white space.

And the extensions:

 (6) Add an end-of-Tx phase notification, thereby allowing kAFS to
     transition the state on its own call record at the correct point,
     rather than having to do it in advance and risk non-completion of the
     call in the wrong state.

 (7) Allow a kernel client call to be retried if it fails on a network
     error, thereby making it possible for kAFS to iterate over a number of
     IP addresses without having to reload the Tx queue and re-encrypt data
     each time.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Florian Westphal says:

====================
addrlabel: don't use rtnl locking

addrlabel doesn't appear to require rtnl lock as the addrlabel
table uses a spinlock to serialize add/delete operations.

Also, entries are reference counted so it should be safe
to call the rtnl ops without the rtnl mutex.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

There appears to be no need to use rtnl, addrlabel entries are refcounted
and add/delete is serialized by the addrlabel table spinlock.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

Now that the IRDA code has moved under drivers/staging/irda/, update the
MAINTAINERS file with the new location.
Reported-by: Joe Perches <joe@perches.com>
Signed-off-by: Greg Kroah-Hartman gregkh@linuxfoundation.org
Signed-off-by: David S. Miller <davem@davemloft.net>

When bnxt VF-reps are not compiled in (CONFIG_BNXT_SRIOV is off)
bnxt_tc.c needs a dummy definition of the routine bnxt_vf_rep_get_fid().
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Fixes: 2ae7408f ("bnxt_en: bnxt: add TC flower filter offload support")
Signed-off-by: Sathya Perla <sathya.perla@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Allow a client call that failed on network error to be retried, provided
that the Tx queue still holds DATA packet 1.  This allows an operation to
be submitted to another server or another address for the same server
without having to repackage and re-encrypt the data so far processed.

Two new functions are provided:

 (1) rxrpc_kernel_check_call() - This is used to find out the completion
     state of a call to guess whether it can be retried and whether it
     should be retried.

 (2) rxrpc_kernel_retry_call() - Disconnect the call from its current
     connection, reset the state and submit it as a new client call to a
     new address.  The new address need not match the previous address.

A call may be retried even if all the data hasn't been loaded into it yet;
a partially constructed will be retained at the same point it was at when
an error condition was detected.  msg_data_left() can be used to find out
how much data was packaged before the error occurred.
Signed-off-by: David Howells <dhowells@redhat.com>

Add a callback to rxrpc_kernel_send_data() so that a kernel service can get
a notification that the AF_RXRPC call has transitioned out the Tx phase and
is now waiting for a reply or a final ACK.

This is called from AF_RXRPC with the call state lock held so the
notification is guaranteed to come before any reply is passed back.

Further, modify the AFS filesystem to make use of this so that we don't have
to change the afs_call state before sending the last bit of data.
Signed-off-by: David Howells <dhowells@redhat.com>

Remove indentation from some blank lines.
Signed-off-by: David Howells <dhowells@redhat.com>