Skip to content

L
linux
Switch branch/tag
  1. 22 Jul, 2019 3 commits
    • Enric Balletbo i Serra's avatar
      SoC: rockchip: rockchip_max98090: Enable MICBIAS for headset keypress detection · f86621cd
      Enric Balletbo i Serra authored 
      The TS3A227E says that the headset keypress detection needs the MICBIAS
power in order to report the key events to ensure proper operation
The headset keypress detection needs the MICBIAS power in order to report
the key events all the time as long as MIC is present. So MICBIAS pin
is forced on when a MICROPHONE is detected.

On Veyron Minnie I observed that if the MICBIAS power is not present and
the key press detection is activated (just because it is enabled when you
insert a headset), it randomly reports a keypress on insert.
E.g. (KEY_PLAYPAUSE)

 Event: (SW_HEADPHONE_INSERT), value 1
 Event: (SW_MICROPHONE_INSERT), value 1
 Event: -------------- SYN_REPORT ------------
 Event: (KEY_PLAYPAUSE), value 1

Userspace thinks that KEY_PLAYPAUSE is pressed and produces the annoying
effect that the media player starts a play/pause loop.

Note that, although most of the time the key reported is the one
associated with BTN_0, not always this is true. On my tests I also saw
different keys reported
Signed-off-by: default avatarEnric Balletbo i Serra <enric.balletbo@collabora.com>
Link: https://lore.kernel.org/r/20190719173929.24065-1-enric.balletbo@collabora.comSigned-off-by: default avatarMark Brown <broonie@kernel.org>
      f86621cd
    • Shengjiu Wang's avatar
      ASoC: cs42xx8: Fix MFREQ selection issue for async mode · 48dfd37a
      Shengjiu Wang authored 
      When sample rate of TX is different with sample rate of RX in
async mode, the MFreq selection will be wrong.

For example, sysclk = 24.576MHz, TX rate = 96000Hz, RX rate = 48000Hz.
Then ratio of TX = 256, ratio of RX = 512, For MFreq is shared by TX
and RX instance, the correct value of MFreq is 2 for both TX and RX.

But original method will cause MFreq = 0 for TX, MFreq = 2 for RX.
If TX is started after RX, RX will be impacted, RX work abnormal with
MFreq = 0.

This patch is to select proper MFreq value according to TX rate and
RX rate.

Fixes: 0c516b4f ("ASoC: cs42xx8: Add codec driver support for CS42448/CS42888")
Signed-off-by: default avatarShengjiu Wang <shengjiu.wang@nxp.com>
Link: https://lore.kernel.org/r/20190716094547.46787-1-shengjiu.wang@nxp.comSigned-off-by: default avatarMark Brown <broonie@kernel.org>
      48dfd37a
    • Charles Keepax's avatar
      ASoC: dapm: Fix handling of custom_stop_condition on DAPM graph walks · 8dd26dff
      Charles Keepax authored 
      DPCM uses snd_soc_dapm_dai_get_connected_widgets to build a
list of the widgets connected to a specific front end DAI so it
can search through this list for available back end DAIs. The
custom_stop_condition was added to is_connected_ep to facilitate this
list not containing more widgets than is necessary. Doing so both
speeds up the DPCM handling as less widgets need to be searched and
avoids issues with CODEC to CODEC links as these would be confused
with back end DAIs if they appeared in the list of available widgets.

custom_stop_condition was implemented by aborting the graph walk
when the condition is triggered, however there is an issue with this
approach. Whilst walking the graph is_connected_ep should update the
endpoints cache on each widget, if the walk is aborted the number
of attached end points is unknown for that sub-graph. When the stop
condition triggered, the original patch ignored the triggering widget
and returned zero connected end points; a later patch updated this
to set the triggering widget's cache to 1 and return that. Both of
these approaches result in inaccurate values being stored in various
end point caches as the values propagate back through the graph,
which can result in later issues with widgets powering/not powering
unexpectedly.

As the original goal was to reduce the size of the widget list passed
to the DPCM code, the simplest solution is to limit the functionality
of the custom_stop_condition to the widget list. This means the rest
of the graph will still be processed resulting in correct end point
caches, but only widgets up to the stop condition will be added to the
returned widget list.

Fixes: 6742064a ("ASoC: dapm: support user-defined stop condition in dai_get_connected_widgets")
Fixes: 5fdd022c ("ASoC: dpcm: play nice with CODEC<->CODEC links")
Fixes: 09464974 ("ASoC: dapm: Fix to return correct path list in is_connected_ep.")
Signed-off-by: default avatarCharles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20190718084333.15598-1-ckeepax@opensource.cirrus.comSigned-off-by: default avatarMark Brown <broonie@kernel.org>
      8dd26dff
  3. 16 Jul, 2019 3 commits
  5. 11 Jul, 2019 2 commits
  7. 10 Jul, 2019 9 commits
  9. 06 Jul, 2019 3 commits
  11. 05 Jul, 2019 4 commits
  13. 03 Jul, 2019 4 commits
  15. 02 Jul, 2019 9 commits
  17. 28 Jun, 2019 3 commits
GitLab Nexedi Edition | About GitLab | About Nexedi | 沪ICP备2021021310号-2 | 沪ICP备2021021310号-7