Signed-off-by: Eric Miao <eric.miao@marvell.com>

1. add common GPIO handling code into [arch/arm/plat-pxa]

2. common code in <mach/gpio.h> moved into <plat/gpio.h>, new processors
   should implement its own <mach/gpio.h>, provide the following required
   definitions and '#include <plat/gpio.h>' in the end:

   - GPIO_REGS_VIRT for mapped virtual address of the GPIO registers'
     physical I/O memory

   - macros of GPLR(), GPSR(), GPDR() for constant optimization for
     functions gpio_{set,get}_value() (so that bit-bang code can still
     have tolerable performance)

   - NR_BUILTIN_GPIO for the number of onchip GPIO

   - definitions of __gpio_is_inverted() and __gpio_is_occupied(), they
     can be either macros or inlined functions
Signed-off-by: Eric Miao <eric.miao@marvell.com>

1. introduce folder of 'arch/arm/plat-pxa' for common code across different
   PXA processor families

2. initially moved DMA code into plat-pxa

3. common code in <mach/dma.h> moved into <plat/dma.h>, new processors
   should implement its own <mach/dma.h>, provide the following required
   definitions and '#include <plat/dma.h>' in the end:

   - DMAC_REGS_VIRT for mapped virtual address of the DMA registers'
     physical I/O memory
Signed-off-by: Eric Miao <eric.miao@marvell.com>

Signed-off-by: Daniel Mack <daniel@caiaq.de>
Cc: Matthias Meier <matthias.j.meier@gmx.net>
Signed-off-by: Eric Miao <eric.miao@marvell.com>

This adds LCD functions for Colibri PXA300 and Colibri PXA320 and
configures a LQ043T3DX02 panel.
Original-code-by: Matthias Meier <matthias.j.meier@gmx.net>
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Signed-off-by: Eric Miao <eric.miao@marvell.com>

This adds basic support for Colibri PXA320 modules.
The file colibri-320.c only contains settings specific to this module,
such as the Ethernet interface.

Cc: Matthias Meier <matthias.j.meier@gmx.net>
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Signed-off-by: Eric Miao <eric.miao@marvell.com>

- Move common function for all Colibri PXA3xx boards to the newly
  added colibri-pxa3xx.c
- Drop some unnecessary defines from colibri.h
- Make Kconfig reflect the fact that code for colibri 300 module does
  also work for the 310 model
- Give up on the huge pin config table which was messed up with lots of
  #ifdefs and switch over to locally defined tables for configured
  functions

Cc: Matthias Meier <matthias.j.meier@gmx.net>
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Signed-off-by: Eric Miao <eric.miao@marvell.com>

Broaden the AX88796 register mask to allow access to the reset register.
Remove unnecessary value definitions and the second resource block.
Diagnosed-by: Matthias Meier <matthias.j.meier@gmx.net>
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Signed-off-by: Eric Miao <eric.miao@marvell.com>

Signed-off-by: Daniel Mack <daniel@caiaq.de>
Signed-off-by: Eric Miao <eric.miao@marvell.com>

Signed-off-by: Daniel Mack <daniel@caiaq.de>
Signed-off-by: Eric Miao <eric.miao@marvell.com>

This adds support for USB OHCI for Toradex' Colibri PXA300 modules as
connected on the evaluation board.
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Signed-off-by: Eric Miao <eric.miao@marvell.com>

Added MMC support for Toradex' Colibri PXA300 module.
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Signed-off-by: Eric Miao <eric.miao@marvell.com>

This patch add basic support for Toradex' Colibri PXA300 module.
Ethernet is enabled conditionally, depdending on CONFIG_AX88796.
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Signed-off-by: Eric Miao <eric.miao@marvell.com>

Namespace cleanup: rename colibri.c to colibri-pxa270.c and change
some names in colibri.h.
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Signed-off-by: Eric Miao <eric.miao@marvell.com>

Merge branch 'fix' of git://git.kernel.org/pub/scm/linux/kernel/git/ycmiao/pxa-linux-2.6.git into devel

Signed-off-by: Daniel Mack <daniel@caiaq.de>
Signed-off-by: Eric Miao <eric.miao@marvell.com>

pxa25x doesn't support overlay in its LCD controller, this patch adds
pxafb_overlay_supported() functions to check the initialization is
necessary.
Signed-off-by: Eric Miao <eric.miao@marvell.com>

clk_add_alias is commonly called for platform devices that are not yet
registered in the device tree. Thus the clock alias is associated with
NULL device name. Fix this by passing the device name instead of just
device pointer.
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: Eric Miao <eric.miao@marvell.com>

Signed-off-by: Daniel Mack <daniel@caiaq.de>
Signed-off-by: Eric Miao <eric.miao@marvell.com>

Signed-off-by: Robert Jarzmik <rjarzmik@free.fr>
Signed-off-by: Eric Miao <eric.miao@marvell.com>

Add gpio vbus detection to udc driver, by taking advantage
of the new gpio_vbus driver.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Eric Miao <eric.miao@marvell.com>

CSB701 is one of baseboards that can be used with CSB726 SOM.
This currently adds support for button and LED on the board.
More to come later.
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: Eric Miao <eric.miao@marvell.com>

Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: Eric Miao <eric.miao@marvell.com>

The typo was originally fixed by Mike Rapoport and missed. And is
later reported by Matthias Meier.
Signed-off-by: Matthias Meier <matthias.j.meier@gmx.net>
Signed-off-by: Mike Rapoport <mike@compulab.co.il>
Signed-off-by: Eric Miao <eric.miao@marvell.com>

Signed-off-by: Mike Rapoport <mike@compulab.co.il>
Signed-off-by: Eric Miao <eric.miao@marvell.com>

The remaining registers are separated into:

   - <mach/regs-ost.h>
   - <mach/regs-rtc.h>
   - <mach/regs-intc.h>

and then we can remove pxa-regs.h completely. Instead of #include this
file, let's:

1. include the specific <mach/regs-*.h> with care (if that's absolutely
   necessary)

2. define the registers in the driver, make cleanly defined API to expose
   the register access to external with sufficient reason
Signed-off-by: Eric Miao <eric.miao@marvell.com>

The definitions of PXA_CS<x>_PHYS are really PXA2xx specific and should
be moved out of pxa-regs.h. As an illustration, the PXA3xx static chip
selects definitions are added into pxa3xx-regs.h.
Signed-off-by: Eric Miao <eric.miao@marvell.com>

This isn't perfect but at least solves the problem of pm.c's dependency
on register definitions in <mach/lubbock.h>, which doesn't make much
sense.
Signed-off-by: Eric Miao <eric.miao@marvell.com>

Move the processor specific initialization (largely resources initialization)
out of soc_common_drv_pcmcia_probe() into dedicated sa11xx_drv_pcmcia_probe()
and __pxa2xx_drv_pcmcia_probe().

By doing this, we are now able to move the PCMCIA related definitions out of
pxa-regs.h and back into pxa2xx_base.c.

As a result, remove that reference of _PCMCIA1IO in arch/arm/mach-pxa/viper.c.
Signed-off-by: Eric Miao <eric.miao@marvell.com>

pxa-regs.h and hardware.h are not intended for use directly in driver
code, remove those unnecessary references.
Signed-off-by: Eric Miao <eric.miao@marvell.com>

The only things prevent drivers/serial/pxa.c from being generic enough
are:

  1. IER_UUE which can be safely replaced by UART_IER_UUE as defined in
     serial_reg.h for PXA

  2. __PREG() and FFUART/BTUART/STUART definitions to decide the UART
     port name

And removed the un-necessary #include of <mach/...> and <asm/...> headers.
Signed-off-by: Eric Miao <eric.miao@marvell.com>

Let's handle GPIOs by banks, each bank covers up to 32 GPIOs with one set
of registers, and each set of registers start from different offsets.

           GPLR    GPDR    GPSR    GPCR    GRER    GFER    GEDR
 BANK 0 - 0x0000  0x000C  0x0018  0x0024  0x0030  0x003C  0x0048
 BANK 1 - 0x0004  0x0010  0x001C  0x0028  0x0034  0x0040  0x004C
 BANK 2 - 0x0008  0x0014  0x0020  0x002C  0x0038  0x0044  0x0050

 BANK 3 - 0x0100  0x010C  0x0118  0x0124  0x0130  0x013C  0x0148
 BANK 4 - 0x0104  0x0110  0x011C  0x0128  0x0134  0x0140  0x014C
 BANK 5 - 0x0108  0x0114  0x0120  0x012C  0x0138  0x0144  0x0150

 NOTE:
   BANK 3 is only available on PXA27x and later processors.
   BANK 4 and 5 are only available on PXA935

1. introduce GPIO_BANK(n) for the offset base of each bank

2. 'struct pxa_gpio_chip' is expanded to include IRQ edge and mask
   setings, and saved register values as well, and is dynamically
   allocated due to possible bank number ranging from 3 to 6

3. all accesses to GPIO registers are made through 'regbase' within
   'pxa_gpio_chip', and register offset

4. introduce several inline functions to simplify the code a bit

5. change IRQ demux handler to base on gpio chips
Signed-off-by: Mike Rapoport <mike@compulab.co.il>
Signed-off-by: Eric Miao <eric.miao@marvell.com>

Signed-off-by: Eric Miao <eric.miao@marvell.com>

This makes gpio.c fully independent of pxa-regs.h (except for the
virtual address of the registers).
Signed-off-by: Mike Rapoport <mike@compulab.co.il>
Signed-off-by: Eric Miao <eric.miao@marvell.com>

Looks like we have to live with pxa_gpio_mode() for a while, giving
its presence is actually making gpio.c not generic enough, let's
move it temporarily outside before it can be fully purged.
Signed-off-by: Eric Miao <eric.miao@marvell.com>

This is part of the work making gpio.c generic enough, the changes
include:

1. move IRQ handling of GPIO 0 and 1 outside (and back into irq.c)

2. pxa_init_gpio() accepts a range for muxed GPIO IRQs, and an IRQ
   number for the muxed GPIOs

3. __gpio_is_occupied() and __gpio_is_inverted() are made inline,
   and are moved into <mach/gpio.h> instead of generic gpio.c
Signed-off-by: Eric Miao <eric.miao@marvell.com>

1. Driver code where pxa_request_dma() is called will most likely
   reference DMA registers as well,  and it is really unnecessary
   to include pxa-regs.h just for this. Move the definitions into
   <mach/dma.h> and make relevant drivers include it instead of
   <mach/pxa-regs.h>.

2. Introduce DMAC_REGS_VIRT as the virtual address base for these
   DMA registers. This allows later processors to re-use the same
   IP while registers may start at different I/O address.
Signed-off-by: Eric Miao <eric.miao@marvell.com>

Signed-off-by: Eric Miao <eric.miao@marvell.com>

Considering the header mess ATM, it is not always possible to include
the correct header files within board code. Let's keep this simple:

  <mach/pxa25x.h>  - for pxa25x based platforms
  <mach/pxa27x.h>  - for pxa27x based platforms
  <mach/pxa300.h>  - for pxa300 based platforms
  <mach/pxa320.h>  - for pxa320 based platforms
  <mach/pxa930.h>  - for pxa930 based platforms

NOTE:

1. one header one board file, they are not compatible (i.e. they have
   conflicting definitions which won't compile if included together).

2. Unless strictly necessary, the following header files are considered
   to be SoC files use _only_, and is not recommended to be included in
   board code:

    <mach/hardware.h>
    <mach/pxa-regs.h>
    <mach/pxa2xx-regs.h>
    <mach/pxa3xx-regs.h>
    <mach/mfp.h>
    <mach/mfp-pxa2xx.h>
    <mach/mfp-pxa25x.h>
    <mach/mfp-pxa27x.h>
    <mach/mfp-pxa3xx.h>
    <mach/mfp-pxa300.h>
    <mach/mfp-pxa320.h>
    <mach/mfp-pxa930.h>
Signed-off-by: Eric Miao <eric.miao@marvell.com>

Signed-off-by: Philipp Zabel <philipp.zabel@gmail.com>
Signed-off-by: Eric Miao <eric.miao@marvell.com>