Pull regulator updates from Mark Brown:
 "The main thing this time around is support for suspend mode
  configuration from DT which will enable some very useful power savings
  on systems where we can't rely on the bootloader configuration.  We
  still don't really support dynamic configuration of this at runtime,
  that may come later if there is any demand.

  Summary:
   - Support for specifying the target regulation mode and voltage
     during system suspend via DT, enabling power savings in that mode.
   - Reduce the default verbosity of the logging on boot, improving boot
     times especially for systems with very large numbers of regulators.
   - Lots of cleanups and fixes for Maxim PMIC drivers.
   - New driver for Richtek RT5033"

* tag 'regulator-v3.19' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator: (62 commits)
  regulator: core: Fix regualtor_ena_gpio_free not to access pin after freeing
  regulator: sky81452: Modify Device Tree structure
  regulator: sky81452: Modify Device Tree structure
  dt-bindings: Update documentation for "system-power-controller" and fix misspellings
  of: Rename "poweroff-source" property to "system-power-controller"
  regulator: max77686: Remove support for board files
  regulator: max77802: Remove support for board files
  regulator: max77802: Fill regulator modes translation callback
  regulator: max77802: Document binding for regulator operating modes
  regulator: of: Add support for parsing initial and suspend modes
  regulator: of: Pass the regulator description in the match table
  regulator: of: Add regulator desc param to of_get_regulator_init_data()
  regulator: Add mode mapping function to struct regulator_desc
  regulator: Document binding for initial and suspend modes
  regulator: core: Add PRE_DISABLE notification
  regulator: gpio: fix parsing of gpio list
  regulator: rpm: add support for RPM-controller SMB208
  regulator: da9063: Do not transform local IRQ to virtual
  regulator: sky81452: Modify dependent Kconfig symbol
  regulator: rt5033: Add RT5033 Regulator device driver
  ...

Pull regmap updates from Mark Brown:
 "A couple of new features this time around, nothing that should have
  any impact on most users:

   - Cleanups and optimization of the path for reading back the register
     defaults from the hardware at startup, reducing boot times for
     devices that use this (most don't, either populating on demand or
     providing defaults).
   - A bus implementation for AC'97 devices"

* tag 'regmap-v3.19' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap:
  regmap: ac97: Add generic AC'97 callbacks
  regmap: cache: Sort include headers alphabetically
  regmap: cache: Fix possible ZERO_SIZE_PTR pointer dereferencing error.
  regmap: cache: use kmalloc_array instead of kmalloc
  regmap: cache: speed regcache_hw_init() up.
  regmap: cache: fix errno in regcache_hw_init()
  regmap: cache: cleanup regcache_hw_init()
  regmap: cache: fix errno in regcache_hw_init()

Merge tag 'hwmon-for-linus-3.19' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging

Pull hwmon updates from Guenter Roeck:
 "Notable changes:
   - new driver for NCT7802Y
   - support for TMP435, LM95233, LM95235, NCT6792D, and NXP LM75B
   - regulator support for PMBus chips, specifically LTX2978
   - support for humidity sensors to iio-hwmon bridge driver

* tag 'hwmon-for-linus-3.19' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging: (21 commits)
  hwmon: (tmp401) Detect TMP435 on all addresses it supports
  hwmon: (lm75) Strengthen detect function
  hwmon: (gpio-fan) Add a shutdown handler to poweroff the fans
  hwmon: (gpio-fan) Allow usage of gpio operations that may sleep
  hwmon: (tmp401) Bail out from tmp401_probe() in case of write errors
  hwmon: (tmp401) Add support for TI TMP435
  hwmon: (lm95234) Add support for LM95233
  hwmon: (lm95245) Add support for LM95235
  hwmon: (ina2xx) bail-out from ina2xx_probe() in case of configuration errors
  hwmon: (nct6775) Add blank lines after declarations
  hwmon: (nct6775) Add support for NCT6792D
  hwmon: (nct6775) Documentation updates
  hwmon: (lm75) Add support for the NXP LM75B
  hwmon: Driver for Nuvoton NCT7802Y
  hwmon: (ibmpowernv) Convert to module_platform_driver
  hwmon: (ibmpowernv) Use platform 'id_table' to probe the device
  hwmon: (iio_hwmon) Add support for humidity sensors
  hwmon: (ltc2978) Add regulator support
  hwmon: (pmbus) Add regulator support
  hwmon: (pmbus) add helpers for byte write and read modify write
  ...

Pull EDAC updates from Borislav Petkov:
 "EDAC updates all over the place:

   - Enablement for AMD F15h models 0x60 CPUs.  Most notably DDR4 RAM
     support.  Out of tree stuff is adding the required PCI IDs.  From
     Aravind Gopalakrishnan.

   - Enable amd64_edac for 32-bit due to popular demand.  From Tomasz
     Pala.

   - Convert the AMD MCE injection module to debugfs, where it belongs.

   - Misc EDAC cleanups"

* tag 'edac_for_3.19' of git://git.kernel.org/pub/scm/linux/kernel/git/bp/bp:
  EDAC, MCE, AMD: Correct formatting of decoded text
  EDAC, mce_amd_inj: Add an injector function
  EDAC, mce_amd_inj: Add hw-injection attributes
  EDAC, mce_amd_inj: Enable direct writes to MCE MSRs
  EDAC, mce_amd_inj: Convert mce_amd_inj module to debugfs
  EDAC: Delete unnecessary check before calling pci_dev_put()
  EDAC, pci_sysfs: remove unneccessary ifdef around entire file
  ghes_edac: Use snprintf() to silence a static checker warning
  amd64_edac: Build module on x86-32
  EDAC, MCE, AMD: Add decoding table for MC6 xec
  amd64_edac: Add F15h M60h support
  {mv64x60,ppc4xx}_edac,: Remove deprecated IRQF_DISABLED
  EDAC: Sync memory types and names
  EDAC: Add DDR3 LRDIMM entries to edac_mem_types
  x86, amd_nb: Add device IDs to NB tables for F15h M60h
  pci_ids: Add PCI device IDs for F15h M60h

Pull MFD updates from Lee Jones:
 "Changes to the core:
   - Honour PLATFORM_DEVID_NONE and PLATFORM_DEVID_AUTO dev IDs

  Changes to existing drivers:
   - IRQ additions/fixes; axp20x, da9063-core
   - Code simplification; i2c-dln2
   - Regmap additions/fixes; max77693
   - Error checking/handling improvements; dln2, db8500-prcmu
   - Bug fixes; dln2, wm8350-core
   - DT support/documentation; max77693, max77686, tps65217, twl4030-power,
                               gpio-tc3589x
   - Decouple syscon interface from platform devices
   - Use MFD hotplug registration; rtsx_usb, viperboard, hid-sensor-hub
   - Regulator fixups; sec-core
   - Power Management additions/fixes; rts5227, tc6393xb
   - Remove relic/redundant code; ab8500-sysctrl, lpc_sch, max77693-private
   - Clean-up/coding style changes; tps65090
   - Clk additions/fixes; tc6393xb, tc6387xb, t7l66xb
   - Add USB-SPI support; dln2
   - Trivial changes; max14577, arizona-spi, lpc_sch, wm8997-tables, wm5102-tables
                      wm5110-tables, axp20x, atmel-hlcdc, rtsx_pci

  New drivers/supported devices:
   - axp288 PMIC support added to axp20x
   - s2mps13 support added to sec-core
   - New support for Diolan DLN-2
   - New support for atmel-hlcdc"

* tag 'mfd-for-linus-3.19' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd: (55 commits)
  mfd: rtsx: Add func to split u32 into register
  mfd: atmel-hlcdc: Add Kconfig option description and name
  mfd: da9063: Get irq base dynamically before registering device
  mfd: max14577: Fix obvious typo in company name in copyright
  mfd: axp20x: Constify axp20x_acpi_match and rid unused warning
  mfd: t7l66xb: prepare/unprepare clocks
  mfd: tc6387xb: prepare/unprepare clocks
  mfd: dln2: add support for USB-SPI module
  mfd: wm5110: Add missing registers for AIF2 channels 3-6
  mfd: tc3589x: get rid of static base
  mfd: arizona: Document HP_CTRL_1L and HP_CTRL_1R registers
  mfd: wm8997: Mark INTERRUPT_STATUS_2_MASK as readable
  mfd: tc6393xb: Prepare/unprepare clocks
  mfd: tps65090: Fix bonkers indenting strategy
  mfd: tc6393xb: Fail ohci suspend if full state restore is required
  mfd: lpc_sch: Don't call mfd_remove_devices()
  mfd: wm8350-core: Fix probable mask then right shift defect
  mfd: ab8500-sysctrl: Drop ab8500_restart
  mfd: db8500-prcmu: Provide sane error path values
  mfd: db8500-prcmu: Check return of devm_ioremap for error
  ...

Pull MMC updates from Ulf Hansson:
 "MMC core:
   - Consolidation and cleanups.
   - Some improvements regarding error handling.
   - Increase maximum amount of block devices.
   - Use correct OCR mask for SDIO when restoring power.
   - Fix prepared requests while doing BKOPS.
   - Convert to modern PM ops.
   - Add mmc_send_tuning() API and convert some hosts to use it.

  MMC host:
   - toshsd: New Toshiba PCI SD controller driver.
   - sdhci: 64-bit ADMA support.
   - sdhci: Some regulator fixes.
   - sdhci: HS400 support.
   - sdhci: Various fixes cleanups.
   - atmel-mci: Modernization and cleanups.
   - atmel-mci: Runtime PM support.
   - omap_hsmmc: Modernization and cleanups.
   - omap_hsmmc: Fix UHS card with DDR50 support.
   - dw_mmc: Support for ARM64 and Exynos 7 variant.
   - dw_mmc: Add support for IMG Pistachio variant.
   - dw_mmc: Various fixes and cleanups.
   - mvsdio: DMA fixes.
   - mxs-mmc: Modernization and cleanups.
   - mxcmmc: Various fixes"

* tag 'mmc-v3.19-1' of git://git.linaro.org/people/ulf.hansson/mmc: (126 commits)
  mmc: sdhci-msm: Convert to mmc_send_tuning()
  mmc: sdhci-esdhc-imx: Convert to mmc_send_tuning()
  mmc: core: Let mmc_send_tuning() to take struct mmc_host* as parameter
  mmc: queue: Improve error handling during allocation of bounce buffers
  mmc: sdhci-acpi: Add two host capabilities for Intel
  mmc: sdhci-pci: Add two host capabilities for BYT
  mmc: sdhci-acpi: Add SDHCI_QUIRK_NO_ENDATTR_IN_NOPDESC
  mmc: sdhci-pci: Add SDHCI_QUIRK_NO_ENDATTR_IN_NOPDESC to BYT
  mmc: atmel-mci: use probe deferring if dma controller is not ready yet
  mmc: atmel-mci: stop using specific initcall
  mmc: atmel-mci: remove __init/__exit attributes
  mmc: atmel-mci: remove useless DMA stuff for non-dt devices
  mmc: omap_hsmmc: Fix UHS card with DDR50 support
  mmc: core: add core-level function for sending tuning commands
  mmc: core: hold SD Clock before CMD11 during Signal
  mmc: mxs-mmc: Check for clk_prepare_enable() error
  mmc: mxs-mmc: Propagate the real error
  mmc: mxs-mmc: No need to do NULL check on 'iores'
  mmc: dw_mmc: Add support for IMG Pistachio
  mmc: mxs-mmc: Simplify PM hooks
  ...

TMP435 supports a range of I2C addresses, not just 0x4c.

Cc: Patrick Titiano <ptitiano@baylibre.com>
Cc: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>

Add helper function to write u32 to registers, if we want to put u32
value to 4 continuous register, this can help us reduce tedious work.
Signed-off-by: Micky Ching <micky_ching@realsil.com.cn>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

Instead of having a local hack taking care of sending the tuning
command and as well to verify the response pattern, let's convert to
the common mmc_send_tuning() API instead.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Georgi Djakov <gdjakov@mm-sol.com>
Acked-by: Georgi Djakov <gdjakov@mm-sol.com>
Reviewed-by: Stephen Boyd <sboyd@codeaurora.org>

Instead of having a local function taking care of sending the tuning
command, let's use the common mmc_send_tuning() API provided by the mmc
core. In this way the request will be handled as any other request by
sdhci core.

As an effect of this change, the pm_runtime_get_sync() call at
esdhc_prepare_tuning() isn't needed any more.

This patch will also introduce another change in behavior, since before
the response pattern to the tuning command wasn't verified by
sdhci-esdhc-imx. The mmc_send_tuning() does that.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Dong Aisheng <b29396@freescale.com>
Acked-by: Dong Aisheng <b29396@freescale.com>

To be able to use mmc_send_tuning() prior the struct mmc_card has been
allocated, let's convert it to take the struct mmc_host* as parameter
instead.
Suggested-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Dong Aisheng <b29396@freescale.com>
Reviewed-by: Stephen Boyd <sboyd@codeaurora.org>

Pull libata fixes from Tejun Heo:
 "Three libata fixes for v3.18.  Nothing too interesting.  PCI ID ID and
  quirk additions to ahci and an error handling path fix in sata_fsl"

* 'for-3.18-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata:
  ahci: disable MSI on SAMSUNG 0xa800 SSD
  sata_fsl: fix error handling of irq_of_parse_and_map
  AHCI: Add DeviceIDs for Sunrise Point-LP SATA controller

Pull watchdog fix from Wim Van Sebroeck:
 "Fix the watchdog mask bit offset for Exynos7"

* git://www.linux-watchdog.org/linux-watchdog:
  watchdog: s3c2410_wdt: Fix the mask bit offset for Exynos7

Pull i2c fixes from Wolfram Sang:
 "Here are two more driver bugfixes for I2C which would be good to have"

* 'i2c/for-current' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
  i2c: cadence: Set the hardware time-out register to maximum value
  i2c: davinci: generate STP always when NACK is received

The watchdog mask bit offset listed for Exynos7 is incorrect.
Fix this.
Signed-off-by: Abhilash Kesavan <a.kesavan@samsung.com>
Acked-by: Naveen Krishna Chatradhi <naveenkrishna.ch@gmail.com
Reviewd-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>

Pull x86 fixes from Thomas Gleixner:
 "Two final fixlets for 3.18:
   - Prevent microcode reload wreckage on 32bit
   - Unbreak cross compilation"

* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86, microcode: Limit the microcode reloading to 64-bit for now
  x86: Use $(OBJDUMP) instead of plain objdump

Pull sound fixlet from Takashi Iwai:
 "Just one commit for adding a copule of HD-audio quirk entries"

* tag 'sound-3.18' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
  ALSA: hda/realtek - Add headset Mic support for new Dell machine

A chip returning 0x00 in all registers is erroneously detected
as LM75. Check hysteresis and temperature limit registers and
abort if both are 0 to reduce the likelyhood for this to happen.
Reviewed-by: Rob Coulson <rob.coulson@gmail.com>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>

Merge remote-tracking branches 'regulator/topic/sky81452' and 'regulator/topic/stub' into regulator-next

Merge remote-tracking branches 'regulator/topic/rn5t618', 'regulator/topic/rpm', 'regulator/topic/rt5033', 'regulator/topic/s2mpa01' and 'regulator/topic/s2mps11' into regulator-next

Merge remote-tracking branches 'regulator/topic/max77686', 'regulator/topic/max77693', 'regulator/topic/max77802', 'regulator/topic/power-off' and 'regulator/topic/rk808' into regulator-next

Merge remote-tracking branches 'regulator/topic/anatop', 'regulator/topic/disable', 'regulator/topic/dummy' and 'regulator/topic/gpio' into regulator-next

Merge branch 'topic/suspend' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator into regulator-sky81452

Conflicts:
	drivers/regulator/sky81452-regulator.c

Allocation of previous bounce buffer in mmc_init_queue when the current
bounce buffer allocation fails was leading to a crash later in
__blk_segment_map_sg. Error handling is improved by allocating previous
bounce buffer only if the current bounce buffer allocation succeeds.
Signed-off-by: Bhuvanesh Surachari <bhuvanesh_surachari@mentor.com>
Signed-off-by: Harish Jenny K N <harish_kandiga@mentor.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

Pull drm intel fixes from Dave Airlie:
 "Two intel stable fixes, that should be it from me for this round"

* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
  drm/i915: Unlock panel even when LVDS is disabled
  drm/i915: More cautious with pch fifo underruns

Pull ACPI backlight fix from Rafael Wysocki:
 "This is a simple fix for an ACPI backlight regression introduced by a
  recent commit that overlooked a corner case which should have been
  taken into account"

* tag 'pm+acpi-3.18-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
  ACPI / video: update condition to check if device is in _DOD list

Silence some pch fifo underrun reports and panel locking backtraces,
both cc: stable.

* tag 'drm-intel-fixes-2014-12-04' of git://anongit.freedesktop.org/drm-intel:
  drm/i915: Unlock panel even when LVDS is disabled
  drm/i915: More cautious with pch fifo underruns

Pull media fixes from Mauro Carvalho Chehab:
 "A core fix and some driver fixes:
   - regression fix in Remote Controller core affecting RC6 protocol
     handling
   - fix video buffer handling in cx23885
   - race fix in solo6x10
   - fix image selection in smiapp
   - fix reported payload size on s2255drv
   - two updates for MAINTAINERS file"

* tag 'media/v3.18-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media:
  [media] rc-core: fix toggle handling in the rc6 decoder
  MAINTAINERS: Update mchehab's addresses
  [media] cx23885: use sg = sg_next(sg) instead of sg++
  [media] s2255drv: fix payload size for JPG, MJPEG
  [media] Update MAINTAINERS for solo6x10
  [media] solo6x10: fix a race in IRQ handler
  [media] smiapp: Only some selection targets are settable

A typo "header=y" was introduced by commit 7071cf7f ("uapi: add
missing network related headers to kbuild").
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Stephen Hemminger <stephen@networkplumber.org>
Cc: David Miller <davem@davemloft.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

After freeing pin from regulator_ena_gpio_free, loop can access
the pin. So this patch fixes not to access pin after freeing.
Signed-off-by: Seung-Woo Kim <sw0312.kim@samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

Poweroff the fans when shutting down the system. Else,
echo '1' > /sys/class/hwmon/hwmon0/fan1_target; poweroff leaves the
fan running if the System power off does not drive the gpio expander
which might control the fan power supply.
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>

Certain I2C based GPIO expanders could be used in sleepable context,
this results in:
[  115.890569] ------------[ cut here ]------------
[  115.895422] WARNING: CPU: 0 PID: 1115 at drivers/gpio/gpiolib.c:1370 gpiod_set_raw_value+0x40/0x4c()
[  115.905024] Modules linked in:
[  115.908229] CPU: 0 PID: 1115 Comm: sh Tainted: G        W      3.18.0-rc7-next-20141203-dirty #1
[  115.917461] Hardware name: Generic DRA74X (Flattened Device Tree)
[  115.923876] [<c0015368>] (unwind_backtrace) from [<c00119f4>] (show_stack+0x10/0x14)
[  115.932013] [<c00119f4>] (show_stack) from [<c05b78e8>] (dump_stack+0x78/0x94)
[  115.939594] [<c05b78e8>] (dump_stack) from [<c003de28>] (warn_slowpath_common+0x7c/0xb4)
[  115.948094] [<c003de28>] (warn_slowpath_common) from [<c003de7c>] (warn_slowpath_null+0x1c/0x24)
[  115.957315] [<c003de7c>] (warn_slowpath_null) from [<c03461e8>] (gpiod_set_raw_value+0x40/0x4c)
[  115.966457] [<c03461e8>] (gpiod_set_raw_value) from [<c04866f4>] (set_fan_speed+0x4c/0x64)
[  115.975145] [<c04866f4>] (set_fan_speed) from [<c04868a8>] (set_rpm+0x98/0xac)
[  115.982742] [<c04868a8>] (set_rpm) from [<c039fb4c>] (dev_attr_store+0x18/0x24)
[  115.990426] [<c039fb4c>] (dev_attr_store) from [<c01b0a28>] (sysfs_kf_write+0x4c/0x50)
[  115.998742] [<c01b0a28>] (sysfs_kf_write) from [<c01afe1c>] (kernfs_fop_write+0xbc/0x19c)
[  116.007333] [<c01afe1c>] (kernfs_fop_write) from [<c0148cc4>] (vfs_write+0xb0/0x1a0)
[  116.015461] [<c0148cc4>] (vfs_write) from [<c0148fbc>] (SyS_write+0x44/0x84)
[  116.022881] [<c0148fbc>] (SyS_write) from [<c000e5c0>] (ret_fast_syscall+0x0/0x48)
[  116.030833] ---[ end trace 3a0b636123acab82 ]---

So, switch over to sleepable GPIO operations as there is no mandatory
need for non-sleepable gpio operations in the fan driver.

This allows the fan driver to be used with i2c based gpio expanders such
as palmas_gpio.
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>

The return value of i2c_smbus_read_byte_data() is checked in
tmp401_init_client(), but only a warning is printed and the device is
registered anyway. This leads to devices being registered even if they
cannot be physically detected.

Bail out from probe in case of write errors and notify the user.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>

Signed-off-by: Patrick Titiano <ptitiano@baylibre.com>
[Bartosz Golaszewski: prepared for submission, code review fixes]
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
[Guenter Roeck: Merged two patches into one]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>

Cadence I2C controller has bug wherein it generates invalid read transactions
after timeout in master receiver mode. This driver does not use the HW
timeout and this interrupt is disabled but the feature itself cannot be
disabled. Hence, this patch writes the maximum value (0xFF) to this register.
This is one of the workarounds to this bug and it will not avoid the issue
completely but reduces the chances of error.
Signed-off-by: Vishnu Motghare <vishnum@xilinx.com>
Signed-off-by: Harini Katakam <harinik@xilinx.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Cc: stable@kernel.org

According to I2C specification the NACK should be handled as follows:
"When SDA remains HIGH during this ninth clock pulse, this is defined as the Not
Acknowledge signal. The master can then generate either a STOP condition to
abort the transfer, or a repeated START condition to start a new transfer."
[I2C spec Rev. 6, 3.1.6: http://www.nxp.com/documents/user_manual/UM10204.pdf]

Currently the Davinci i2c driver interrupts the transfer on receipt of a
NACK but fails to send a STOP in some situations and so makes the bus
stuck until next I2C IP reset (idle/enable).

For example, the issue will happen during SMBus read transfer which
consists from two i2c messages write command/address and read data:

S Slave Address Wr A Command Code A Sr Slave Address Rd A D1..Dn A P
<--- write -----------------------> <--- read --------------------->

The I2C client device will send NACK if it can't recognize "Command Code"
and it's expected from I2C master to generate STP in this case.
But now, Davinci i2C driver will just exit with -EREMOTEIO and STP will
not be generated.

Hence, fix it by generating Stop condition (STP) always when NACK is received.

This patch fixes Davinci I2C in the same way it was done for OMAP I2C
commit cda2109a ("i2c: omap: query STP always when NACK is received").
Reviewed-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reported-by: Hein Tibosch <hein_tibosch@yahoo.es>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Cc: stable@kernel.org

Just like 0x1600 which got blacklisted by 66a7cbc3 ("ahci: disable
MSI instead of NCQ on Samsung pci-e SSDs on macbooks"), 0xa800 chokes
on NCQ commands if MSI is enabled.  Disable MSI.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: Dominik Mierzejewski <dominik@greysector.net>
Link: https://bugzilla.kernel.org/show_bug.cgi?id=89171
Cc: stable@vger.kernel.org