- 11 Sep, 2019 6 commits
-
-
Guangbin Huang authored
This patch checks ops->set_default_reset_request whether is NULL before using it in function hns3_slot_reset. Signed-off-by:
Guangbin Huang <huangguangbin2@huawei.com> Signed-off-by:
Huazhong Tan <tanhuazhong@huawei.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Guangbin Huang authored
The pfc_en and pfc_map need to be displayed in hexadecimal notation, printing dma address should use %pad, and the end of printed string needs to be add "\n". This patch modifies them. Signed-off-by:
-
Guangbin Huang authored
For hardware doesn't support use specified speed and duplex to negotiate, it's unnecessary to check and modify the port speed and duplex for fibre port when autoneg is on. Fixes: 22f48e24 ("net: hns3: add autoneg and change speed support for fibre port") Signed-off-by:
-
Yonglong Liu authored
Currently when hns3 driver configures the tm shaper to limit bandwidth below 20Mbit using the parameters calculated by hclge_shaper_para_calc(), the actual bandwidth limited by tm hardware module is not accurate enough, for example, 1.28 Mbit when the user is configuring 1 Mbit. This patch adjusts the ir_calc to be closer to ir, and always calculate the ir_b parameter when user is configuring a small bandwidth. Also, removes an unnecessary parenthesis when calculating denominator. Fixes: 84844054 ("net: hns3: Add support of TX Scheduler & Shaper to HNS3 driver") Signed-off-by:
Yonglong Liu <liuyonglong@huawei.com> Signed-off-by:
-
Peng Li authored
After setting new channel num, it needs free old ring memory and allocate new ring memory. If there is no enough memory and allocate new ring memory fail, the ring may initialize fail. To make sure the network interface can work normally, driver should revert the channel to the old configuration. Signed-off-by:
Peng Li <lipeng321@huawei.com> Signed-off-by:
-
Guangbin Huang authored
This patch adds ethtool_ops.set_channels support for HNS3 VF driver, and updates related TQP information and RSS information, to support modification of VF TQP number, and uses current rss_size instead of max_rss_size to initialize RSS. Also, fixes a format error in hclgevf_get_rss(). Signed-off-by:
-
- 10 Sep, 2019 18 commits
-
-
David S. Miller authored
Simon Horman says: ==================== nfp: implement firmware loading policy Dirk says: This series adds configuration capabilities to the firmware loading policy of the NFP driver. NFP firmware loading is controlled via three HWinfo keys which can be set per device: 'abi_drv_reset', 'abi_drv_load_ifc' and 'app_fw_from_flash'. Refer to patch #11 for more detail on how these control the firmware loading. In order to configure the full extend of FW loading policy, a new devlink parameter has been introduced, 'reset_dev_on_drv_probe', which controls if the driver should reset the device when it's probed. This, in conjunction with the existing 'fw_load_policy' (extended to include a 'disk' option) provides the means to tweak the NFP HWinfo keys as required by users. Patches 1 and 2 adds the devlink modifications and patches 3 through 9 adds the support into the NFP driver. Furthermore, the last 2 patches are documentation only. v2: Renamed all 'reset_dev_on_drv_probe' defines the same as the devlink parameter name (Jiri) ==================== Signed-off-by: -
Dirk van der Merwe authored
This adds the initial documentation for the NFP driver specific documentation. Right now, only basic information is provided about acquiring firmware and configuring device firmware loading. Original driver documentation can be found here: https://github.com/Netronome/nfp-drv-kmods/blob/master/README.mdSigned-off-by:
Dirk van der Merwe <dirk.vandermerwe@netronome.com> Signed-off-by:
Jakub Kicinski <jakub.kicinski@netronome.com> Signed-off-by:
Simon Horman <simon.horman@netronome.com> Signed-off-by:
-
Dirk van der Merwe authored
Fixed the incorrect prefix for the 'nfp_fw_load' function. Signed-off-by:
-
Dirk van der Merwe authored
Add support for the 'reset_dev_on_drv_probe' devlink parameter. The reset control policy is controlled by the 'abi_drv_reset' hwinfo key. Signed-off-by:
-
Dirk van der Merwe authored
Add support for the 'fw_load_policy' devlink parameter. The FW load policy is controlled by the 'app_fw_from_flash' hwinfo key. Remap the values from devlink to the hwinfo key and back. Signed-off-by:
-
Dirk van der Merwe authored
Register devlink parameters for driver use. Subsequent patches will add support for specific parameters. In order to support devlink parameters, the management firmware needs to be able to lookup and set hwinfo keys. Signed-off-by:
-
Dirk van der Merwe authored
The firmware reset and loading policies can be controlled with the combination of three hwinfo keys, 'abi_drv_reset', 'abi_drv_load_ifc' and 'app_fw_from_flash'. 'app_fw_from_flash' defines which firmware should take precedence, 'Disk', 'Flash' or the 'Preferred' firmware. When 'Preferred' is selected, the management firmware makes the decision on which firmware will be loaded by comparing versions of the flash firmware and the host supplied firmware. 'abi_drv_reset' defines when the driver should reset the firmware when the driver is probed, either 'Disk' if firmware was found on disk, 'Always' reset or 'Never' reset. Note that the device is always reset on driver unload if firmware was loaded when the driver was probed. 'abi_drv_load_ifc' defines a list of PF devices allowed to load FW on the device. Furthermore, we limit the cases to where the driver will unload firmware again when the driver is removed to only when firmware was loaded by the driver and only if this particular device was the only one that could have loaded firmware. This is needed to avoid firmware being removed while in use on multi-host platforms. Signed-off-by:
-
Dirk van der Merwe authored
Add support for the NSP HWinfo set command. This closely follows the HWinfo lookup command. Signed-off-by:
-
Dirk van der Merwe authored
There are cases where we want to read a hwinfo entry from the NFP, and if it doesn't exist, use a default value instead. To support this, we must silence warning/error messages when the hwinfo entry doesn't exist since this is a valid use case. The NSP command structure provides the ability to silence command errors, in which case the caller should log any command errors appropriately. Protocol errors are unaffected by this. Signed-off-by:
-
Dirk van der Merwe authored
Add support for the simple command that indicates whether application firmware is loaded. Signed-off-by:
-
Dirk van der Merwe authored
Add the 'reset_dev_on_drv_probe' devlink parameter, controlling the device reset policy on driver probe. This parameter is useful in conjunction with the existing 'fw_load_policy' parameter. Signed-off-by:
-
Dirk van der Merwe authored
Add the 'disk' value to the generic 'fw_load_policy' devlink parameter. This value indicates that firmware should always be loaded from disk only. Signed-off-by:
-
David S. Miller authored
Vivien Didelot says: ==================== net: dsa: mv88e6xxx: add PCL support This small series implements the ethtool RXNFC operations in the mv88e6xxx DSA driver to configure a port's Layer 2 Policy Control List (PCL) supported by models such as 88E6352 and 88E6390 and equivalent. This allows to configure a port to discard frames based on a configured destination or source MAC address and an optional VLAN, with e.g.: # ethtool --config-nfc lan1 flow-type ether src 00:11:22:33:44:55 action -1 ==================== Signed-off-by: -
Vivien Didelot authored
Implement the .get_rxnfc and .set_rxnfc DSA operations to configure a port's Layer 2 Policy Control List (PCL) via ethtool. Currently only dropping frames based on MAC Destination or Source Address (including the option VLAN parameter) is supported. Signed-off-by:
Vivien Didelot <vivien.didelot@gmail.com> Reviewed-by:
Florian Fainelli <f.fainelli@gmail.com> Reviewed-by:
Andrew Lunn <andrew@lunn.ch> Signed-off-by:
-
Vivien Didelot authored
Introduce a new .port_set_policy operation to configure a port's Policy Control List, based on mapping such as DA, SA, Etype and so on. Models similar to 88E6352 and 88E6390 are supported at the moment. Signed-off-by:
-
Vivien Didelot authored
Marvell has different values for the state of a MAC address, depending on its multicast bit. This patch completes the definitions for these states. At the same time, use 0 which is intuitive enough and simplifies the code a bit, instead of the UC or MC unused value. Signed-off-by:
-
Colin Ian King authored
Don't populate the array modes on the stack but instead make it static const. Makes the object code smaller by 303 bytes. Before: text data bss dec hex filename 51240 5008 1312 57560 e0d8 mellanox/mlx4/en_ethtool.o After: text data bss dec hex filename 50937 5008 1312 57257 dfa9 mellanox/mlx4/en_ethtool.o (gcc version 9.2.1, amd64) Signed-off-by:
Colin Ian King <colin.king@canonical.com> Signed-off-by:
-
git://git.kernel.org/pub/scm/linux/kernel/git/jkirsher/next-queueDavid S. Miller authored
Jeff Kirsher says: ==================== Intel Wired LAN Driver Updates 2019-09-09 This series contains a variety of cold and hot savoury changes to Intel drivers. Some of the fixes could be considered for stable even though the author did not request it. Hulk Robert cleans up (i.e. removes) a function that has no caller for the iavf driver. Radoslaw fixes an issue when there is no link in the VM after the hypervisor is restored from a low-power state due to the driver not properly restoring features in the device that had been disabled during the suspension for ixgbevf. Kai-Heng Feng modified e1000e to use mod_delayed_work() to help resolve a hot plug speed detection issue by adding a deterministic 1 second delay before running watchdog task after an interrupt. Sasha moves functions around to avoid forward declarations, since the forward declarations are not necessary for these static functions in igc. Also added a check for igc during driver probe to validate the NVM checksum. Cleaned up code defines that were not being used in the igc driver. Adds support for IP generic transmit checksum offload in the igc driver. Updated the iavf kernel documentation by a developer with no life. Jake provides another fm10k update to a local variable for ease of code readability. Mitch fixes the iavf driver to allow the VF to override the MAC address set by the host, if the VF is in "trusted" mode. Mauro S. M. Rodrigues provides several changes for i40e driver, first with resolving hw_dbg usage and referencing a i40e_hw attribute. Also implemented a debug macro using pr_debug, since the use of netdev_dbg could cause a NULL pointer dereference during probe. Finally cleaned up code that is no longer used or needed. Firo Yang provides a change in the ixgbe driver to ensure we sync the first fragment unconditionally to help resolve an issue seen in the XEN environment when the upper network stack could receive an incomplete network packet. Mariusz adds a missing device to the i40e PCI table in the driver. v2: Mauro S. M. Rodrigues updated patches 10 & 11 of the series based on feedback from Jakub Kicinski. Also updated patch 13 description so that the "Fixes:" tag was no wrapped. ==================== Signed-off-by:
-
- 09 Sep, 2019 15 commits
-
-
Mariusz Stachura authored
Add I40E_DEV_ID_10G_BASE_T_BC to i40e_pci_tbl Signed-off-by:
Mariusz Stachura <mariusz.stachura@intel.com> Tested-by:
Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by:
Jeff Kirsher <jeffrey.t.kirsher@intel.com>
-
Sasha Neftin authored
Add IP generic TX checksum offload functionality. Signed-off-by:
Sasha Neftin <sasha.neftin@intel.com> Tested-by:
Aaron Brown <aaron.f.brown@intel.com> Signed-off-by:
-
Firo Yang authored
In Xen environment, if Xen-swiotlb is enabled, ixgbe driver could possibly allocate a page, DMA memory buffer, for the first fragment which is not suitable for Xen-swiotlb to do DMA operations. Xen-swiotlb have to internally allocate another page for doing DMA operations. This mechanism requires syncing the data from the internal page to the page which ixgbe sends to upper network stack. However, since commit f3213d93 ("ixgbe: Update driver to make use of DMA attributes in Rx path"), the unmap operation is performed with DMA_ATTR_SKIP_CPU_SYNC. As a result, the sync is not performed. Since the sync isn't performed, the upper network stack could receive a incomplete network packet. By incomplete, it means the linear data on the first fragment(between skb->head and skb->end) is invalid. So we have to copy the data from the internal xen-swiotlb page to the page which ixgbe sends to upper network stack through the sync operation. More details from Alexander Duyck: Specifically since we are mapping the frame with DMA_ATTR_SKIP_CPU_SYNC we have to unmap with that as well. As a result a sync is not performed on an unmap and must be done manually as we skipped it for the first frag. As such we need to always sync before possibly performing a page unmap operation. Fixes: f3213d93 ("ixgbe: Update driver to make use of DMA attributes in Rx path") Signed-off-by:
Firo Yang <firo.yang@suse.com> Reviewed-by:
Alexander Duyck <alexander.h.duyck@linux.intel.com> Tested-by:
-
Mauro S. M. Rodrigues authored
Since commit '5098850c ("i40e/i40evf: i40e_register.h updates")' it is no longer possible to trigger an EMP Reset from debugfs, but it's possible to request it either way, to end up with a bad reset request: echo empr > /sys/kernel/debug/i40e/0002\:01\:00.1/command i40e 0002:01:00.1: debugfs: forcing EMPR i40e 0002:01:00.1: bad reset request 0x00010000 So let's remove this piece of code and show the available valid commands as it is when any invalid command is issued. Signed-off-by:
"Mauro S. M. Rodrigues" <maurosr@linux.vnet.ibm.com> Tested-by:
-
Mauro S. M. Rodrigues authored
There are several uses of hw_dbg in the code, producing no output. This patch implements it using dev_debug. Initially the intention was to implement it using netdev_dbg, analogously to what is done in ixgbe for instance. That approach was avoided due to some early usages of hw_dbg, like i40e_pf_reset, before the VSI structure initialization causing NULL pointer dereference during the driver probe if the debug messages were turned on as soon as the module is probed. v2: - Use dev_dbg instead of pr_debug, and take advantage of dev_name instead of crafting pretty much the same device name locally as suggested by Jakub Kicinski. Signed-off-by:
-
Mauro S. M. Rodrigues authored
The mentioned function references a i40e_hw attribute, as parameter for hw_dbg, but it doesn't exist in the function scope. Fixes it by changing parameters from i40e_hmc_info to i40e_hw which can retrieve the necessary i40e_hmc_info. v2: - Fixed reverse xmas tree code style issue as suggested by Jakub Kicinski Signed-off-by:
-
Sasha Neftin authored
PCIe device control 2 defines does not use internally. This patch comes to clean up those. Signed-off-by:
-
Mitch Williams authored
Allow the VF to override the "permanent" MAC address set by the host. This allows bonding to work in the case where the administrator has set the VF MAC. Note that the VF must still be set to Trusted on the host if this change is to be accepted by the PF driver. Signed-off-by:
Mitch Williams <mitch.a.williams@intel.com> Tested-by:
-
Sasha Neftin authored
Add NVM checksum validation during probe functionality. Signed-off-by:
-
Jacob Keller authored
In the function fm10k_xmit_frame_ring, we recently switched to using the skb_frag_size accessor instead of directly using the size member of the skb fragment. This made the for loop slightly harder to read because it created a very long line that is difficult to split up. Avoid this by using a local variable in the for loop, so that we do not have to break the line on an open parenthesis. Signed-off-by:
Jacob Keller <jacob.e.keller@intel.com> Tested-by:
-
Jeff Kirsher authored
Update the LAN driver documentation to include the latest feature implementation and driver capabilities. Signed-off-by:
-
Sasha Neftin authored
Move igc_phy_setup_autoneg, igc_wait_autoneg and igc_set_fc_watermarks up to avoid forward declaration. It is not necessary to forward declare these static methods. Signed-off-by:
-
Kai-Heng Feng authored
After hot plugging an 1Gbps Ethernet cable with 1Gbps link partner, the MII_BMSR may report 10Mbps, renders the network rather slow. The issue has much lower fail rate after commit 59653e64 ("e1000e: Make watchdog use delayed work"), which essentially introduces some delay before running the watchdog task. But there's still a chance that the hot plugging event and the queued watchdog task gets run at the same time, then the original issue can be observed once again. So let's use mod_delayed_work() to add a deterministic 1 second delay before running watchdog task, after an interrupt. Signed-off-by:
Kai-Heng Feng <kai.heng.feng@canonical.com> Tested-by:
-
Radoslaw Tyl authored
This patch fixed issue in VM which shows no link when hypervisor is restored from low-power state. The driver is responsible for re-enabling any features of the device that had been disabled during suspend calls, such as IRQs and bus mastering. Signed-off-by:
Radoslaw Tyl <radoslawx.tyl@intel.com> Tested-by:
-
YueHaibing authored
There is no caller of function iavf_debug_d() in tree since commit 75051ce4 ("iavf: Fix up debug print macro"), so it can be removed. Reported-by:
Hulk Robot <hulkci@huawei.com> Signed-off-by:
YueHaibing <yuehaibing@huawei.com> Tested-by:
-
- 07 Sep, 2019 1 commit
-
-
David S. Miller authored
Jakub Kicinski says: ==================== net/tls: small TX offload optimizations This set brings small TLS TX device optimizations. The biggest gain comes from fixing a misuse of non temporal copy instructions. On a synthetic workload modelled after customer's RFC application I see 3-5% percent gain. ==================== Signed-off-by:
-
