- 08 Jun, 2013 14 commits
-
-
Reinhard Nißl authored
It seems that current inversion handling addresses only the signal routing on the PCB, i. e. IQ signals are either swapped or not. But when the device is operated in a Satellite Channel Router (SCR) environment, an additional inversion is required due to the way how the SCR works. Therefore it makes sense to me to always enable auto inversion handling and drop the enum value IQ_SWAP_AUTO. Signed-off-by:
Reinhard Nißl <rnissl@gmx.de> Signed-off-by:
Michael Krufky <mkrufky@linuxtv.org> Signed-off-by:
Mauro Carvalho Chehab <mchehab@redhat.com>
-
Zoran Turalija authored
This makes minimum symbol rate driver capabilities on par with windows driver, and allows tuning on linux to transponders that have symbol rate below 5000000, too. Patch was tested successfully on Eutelsat 16A transponders that became reachable with it (1000000 < symbol rate < 5000000): * DVB/S 12507050 V 2532000 3/4 * DVB/S2 12574000 V 4355000 3/4 8PSK * DVB/S 12593000 V 2500000 2/3 * DVB/S 12596940 V 2848000 2/3 * DVB/S 12600750 V 2500000 1/2 * DVB/S 12675590 H 4248000 3/4 Signed-off-by:Zoran Turalija <zoran.turalija@gmail.com> Signed-off-by:
-
Reinhard Nißl authored
Contrary to the chip's specs, the register's value is signed, so we need to sign extend the value before using it in calculations like when determining the offset frequency. Signed-off-by:
-
Thomas Meyer authored
Signed-off-by:
Thomas Meyer <thomas@m3y3r.de> Signed-off-by:
-
Gianluca Gennari authored
fe->tuner_priv is already freed by hybrid_tuner_release_state(). Signed-off-by:
Gianluca Gennari <gennarone@gmail.com> Signed-off-by:
-
Geert Uytterhoeven authored
drivers/media/dvb-frontends/dib8000.c: In function ‘dib8000_set_frontend’: drivers/media/dvb-frontends/dib8000.c:3556: warning: ‘ret’ is used uninitialized in this function Remove the variable and return zero instead. Signed-off-by:
Geert Uytterhoeven <geert@linux-m68k.org> Signed-off-by:
-
Laurent Pinchart authored
Maintaining the users count using an atomic variable makes sure that access to the counter won't be racy, but doesn't serialize access to the operations protected by the counter. This creates a race condition that could result in the status URB being submitted multiple times. Use a mutex to protect the users count and serialize access to the status start and stop operations. Reported-by:
Shawn Nematbakhsh <shawnn@chromium.org> Signed-off-by:
Laurent Pinchart <laurent.pinchart@ideasonboard.com> Signed-off-by:
-
Joseph Salisbury authored
BugLink: http://bugs.launchpad.net/bugs/1180409 OminiVision webcam 0x05a9:0x2643 needs the same UVC_QUIRK_PROBE_DEF as other OmniVision models to work properly. Signed-off-by:
Joseph Salisbury <joseph.salisbury@canonical.com> Signed-off-by:
-
Kamal Mostafa authored
BugLink: https://bugs.launchpad.net/bugs/1168430 OminiVision webcam 0x05a9:0x264a (in Dell Studio Hybrid 140g) needs the same UVC_QUIRK_PROBE_DEF as other OmniVision model to be recognized consistently. Signed-off-by:
Kamal Mostafa <kamal@canonical.com> Signed-off-by:
-
Philipp Zabel authored
If we just declare the job finished here while the CODA is still running, the call to v4l2_m2m_ctx_release in coda_release, which is supposed to wait for a running job to finish, will return immediately and free memory that the CODA is still using. Just set the 'aborting' flag and let coda_irq_handler deal with it. Signed-off-by:
Philipp Zabel <p.zabel@pengutronix.de> Signed-off-by:
Kamil Debski <k.debski@samsung.com> Signed-off-by:
-
Philipp Zabel authored
Not only do we need to wait for job completion when we want to call a command on the CODA in start/stop_streaming, we also need to make sure that a new job doesn't start before the command finished. Use a mutex to lock the coda command handling. On timeout, the device_run job must be marked as finished and the mutex released, as otherwise coda_release will block. Signed-off-by:
-
Philipp Zabel authored
In preparation for CODA7541 and CODA960 multi-stream support and for replacement of the completion with a mutex lock, consolidate the header encoding in a helper function. Signed-off-by:
-
Philipp Zabel authored
This patch adds a list of supported codecs per device type which is used to determine the allowed pixel formats and maximum frame sizes depending on the possible codecs. It allows frame sizes larger than 720 x 576 on CODA7 and adds support for the YVU420 (planar YUV 4:2:0 with switched Cb and Cr) format. Other uncompressed formats that could be added in the future are the chroma interleaved NV12 and NV21 formats and the multiplanar variants YUV420M, YVU420M, NV12M, and NV21M. Further, rawstreamon is renamed to streamon_out and compstreamon is renamed to streamon_cap in preparation for decoding support. The maximum encoded frame buffer size is increased to 1 MiB. Instead of tracking inst_type and codec across S_FMT calls, set the codec and inst_type in start_streaming. Signed-off-by:
-
Philipp Zabel authored
Signed-off-by:
-
- 03 Jun, 2013 4 commits
-
-
Philipp Zabel authored
Signed-off-by:
-
Philipp Zabel authored
The application must have filled the bytesused field, don't overwrite it here. Signed-off-by:
-
Philipp Zabel authored
Signed-off-by:
-
Philipp Zabel authored
GAMMA_OFFSET is different between CodaDx6 and CODA7. Also, this is a bitfield. Signed-off-by:
-
- 27 May, 2013 22 commits
-
-
Lad, Prabhakar authored
This patch removes check for EPERM in dbg_g/s_register and vidioc_g/s_register as this check is already performed by core. Signed-off-by:
Lad, Prabhakar <prabhakar.csengg@gmail.com> Signed-off-by:
Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by:
-
Lad, Prabhakar authored
This patch removes check for EPERM in vidioc_g/s_register as this check is already performed by core. Signed-off-by:
-
Lad, Prabhakar authored
This patch removes check for EPERM in dbg_g/s_register as this check is already performed by core. Signed-off-by:
-
Lad, Prabhakar authored
This patch removes check for EPERM in dbg_g/s_register of subdevice drivers as this check is already performed by core. Signed-off-by:
-
Philipp Zabel authored
The timeout delayed work might be scheduled even after the v4l2 device is released. Signed-off-by:
-
Philipp Zabel authored
Use ret from the outer scope, instead of redefining it in the conditional clause. That way the error value reaches the end of the function as intended. Signed-off-by:
-
Philipp Zabel authored
Otherwise module/coda/parameters/coda_debug won't show up in sysfs. Signed-off-by:
-
Philipp Zabel authored
Signed-off-by:
-
Philipp Zabel authored
Signed-off-by:
-
Philipp Zabel authored
Signed-off-by:
-
Sachin Kamat authored
Commit 0998d063 (device-core: Ensure drvdata = NULL when no driver is bound) removes the need to set driver data field to NULL. Signed-off-by:
Sachin Kamat <sachin.kamat@linaro.org> Signed-off-by:
-
Sachin Kamat authored
Commit 0998d063 (device-core: Ensure drvdata = NULL when no driver is bound) removes the need to set driver data field to NULL. Signed-off-by:
-
Hans Verkuil authored
bw-qcam didn't set the timestamp and it didn't set q->timestamp_type. Tested-by:
Borislav Petkov <bp@suse.de> Signed-off-by:
-
Lad, Prabhakar authored
This patch rearranges the description of field members of struct tvp7002_config. Also as the all the fields where accepting a value either 0/1, made the members as bool. Signed-off-by:
-
Lad, Prabhakar authored
this patch removes duplicate #define TVP7002_MODULE_NAME form the driver file, which was also defined in media/tvp7002.h Signed-off-by:
-
Leonid Kegulskiy authored
[mchehab@redhat.com: CodingStyle fixes] Signed-off-by:
Leonid Kegulskiy <leo@lumanate.com> Signed-off-by:
-
Lad, Prabhakar authored
This patch fixes several typos in videodev2.h file Signed-off-by:
-
Jean Delvare authored
Module parameter descriptions need not be terminated with a newline. Signed-off-by:
Jean Delvare <khali@linux-fr.org> Signed-off-by:
-
Wei Yongjun authored
The orig code will release all the resources if v4l2_device_register() failed and return 0. But what we need in this case is to return an negative error code to let the caller known we are failed. So the patch save the return value of v4l2_device_register() to 'ret' and return it when error. Signed-off-by:
Wei Yongjun <yongjun_wei@trendmicro.com.cn> Signed-off-by:
-
Wei Yongjun authored
Fix to return a negative error code from the error handling case instead of 0, as done elsewhere in this function. Signed-off-by:
Scott Jiang <scott.jiang.linux@gmail.com> Signed-off-by:
-
Wei Yongjun authored
Fix to return a negative error code from the error handling case instead of 0, as done elsewhere in this function. Signed-off-by:
-
Wei Yongjun authored
Fix to return -ENODEV in the subdevice register error handling case instead of 0, as done elsewhere in this function. Signed-off-by:
-
