Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

Conflicts:

	net/netfilter/nf_conntrack_proto_tcp.c

Signed-off-by: David S. Miller <davem@davemloft.net>

According to the legacy drivers the LED association status
must be reset after the firmware has been uploaded to the
hardware.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This is a small fix to change the idx type from int to unsigned.
Signed-off-by: Abhijeet Kolekar <abhijeet.kolekar@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

The patch fixes LEDs problem for 3945.
Signed-off-by: Abhijeet Kolekar <abhijeet.kolekar@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

The patch fixes the problem that TXPOWER command is not sent
after we issue a new RXON command which requires a tune. Otherwise
we won't be able to Tx any frames.
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This patch enables active scan on active channels.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This patch unifies 4965 and 5000 scanning code.

We increases the version number to 1.3.27. Since new uCode
iwlwifi-4965-2.ucode is required for 4965 cards.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This patch makes correct usage of the LED blink table.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This patch fixes LED stall. last_blink_time was updated only if LED command
was sent, causing wrong computation of the througput.
Some code cleanup comes with this patch as well
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This patch asks to allocate the correct amount of sw queues according
to hw ampdu queues number.
Signed-off-by: Ron Rindjunsky <ron.rindjunsky@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This patch fixes iwl4965_mac_conf_tx. A mutex was taken in atomic context
leading to Oops. This patch removes the mutex and extends the hold
priv->lock. None of the field of QOS is accessed without priv->lock held.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This patch fixes printk NULL pointer exceptions in rs code.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Guy Cohen <guy.cohen@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This patch removes post associate work. It wasn't used.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This patch fixes the RTS / CTS support in iwlwifi. 5000 will send CTS to
self when allowed by spec, 4965 will send RTS or CTS to self according to
mac80211 request.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

The patch adds PCI device IDs to iwl_hw_card_ids.
Signed-off-by: Esti Kummer <stkumer@localhost.localdomain>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mac802 can handle duplicate packages on its own, so let it do it.
The patch is based on patch from Johannes Berg for iwl4965.
Signed-off-by: Adel Gadllah <adel.gadllah@gmail.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This patch avoids adding STAs that don't belong to our IBSS
ieee80211_bssid_match matches also bcast address so also APs
were added
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Use directly put_unaligned_leX instead of put_unaligned(cpu_to_leX
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Radiotap is entirely little endian. Found with sparse.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Multiple issues:
 - there are no "default" values needed
 - cw_min/cw_max can be larger than documented
 - restructure to decrease size
 - use get_unaligned_le16
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This patch makes mac80211 assign proper sequence numbers to
QoS-data frames. It also removes the old sequence number code
because we noticed that only the driver or hardware can assign
sequence numbers to non-QoS-data and especially management
frames in a race-free manner because beacons aren't passed
through mac80211's TX path.

This patch also adds temporary code to the rt2x00 drivers to
not break them completely, that code will have to be reworked
for proper sequence numbers on beacons.

It also moves sequence number assignment down in the TX path
so no sequence numbers are assigned to frames that are dropped.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

The /sys/class/net/*/wireless/ direcory is, as far as I know, not
used by anyone. Additionally, the same data is available via wext
ioctls. Hence the sysfs files are pretty much useless. This patch
makes them optional and schedules them for removal.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Cc: Jean Tourrilhes <jt@hpl.hp.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

According to 802.11-2007, we are doing the wrong thing in the
sequence number checks when receiving frames. This fixes it.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This patch fixes the check at the entrance to ieee80211_rx_reorder_ampdu.
This check has been broken by 'mac80211: rx.c use new helpers'.

Letting QoS NULL packet in ieee80211_rx_reorder_ampdu led to packet loss in
RX.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

For RTL8187B it seems we need special values too for ANAPARAM*_OFF
values (and not use RTL8187 ones). The ANAPARAM*_OFF values used are the
stock ones read from the hardware after a cold boot.
Signed-off-by: Herton Ronaldo Krzesinski <herton@mandriva.com.br>
Signed-off-by: Hin-Tak Leung <htl10@users.sourceforge.net>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ssb.h implements DMA mapping functions, so it should
include dma-mapping.h. This fixes compile failures on certain architectures.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

With the new beacon handling from mac80211 we can
reorganize the beacon handling in rt2x00 as well.
This patch will move the function to the TX handlers,
and move all duplicate code into rt2x00queue.c.

After this change the descriptor helper functions
from rt2x00queue.c no longer need to be exported
outside of rt2x00lib and can be declared static.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Inform drivers about the changed CTS protection settings.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This patch changes mac80211's beacon configuration handling
to never pass skbs to the driver directly but rather always
require the driver to use ieee80211_beacon_get(). Additionally,
it introduces "change flags" on the config_interface() call
to enable drivers to figure out what is changing. Finally, it
removes the beacon_update() driver callback in favour of
having IBSS beacon delivered by ieee80211_beacon_get() as well.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This patch pushes the "netif_running()" and "same type as before"
checks down into ieee80211_if_change_type() to centralise the
logic instead of duplicating it for cfg80211 and wext.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This patch revamps the virtual interface handling and makes the
code much easier to follow. Fewer functions, better names, less
spaghetti code.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Currently, almost every interface type has a 'bss' pointer
pointing to BSS information. This BSS information, however,
is for a _local_ BSS, not for the BSS we joined, so having
it on a STA mode interface makes little sense, but now they
have it pointing to the master device, which is an AP mode
virtual interface. However, except for some bitrate control
data, this pointer is only used in AP/VLAN modes (for power
saving stations.)

Overall, it is not necessary to even have the master netdev
be a valid virtual interface, and it doesn't have to be on
the list of interfaces either.

This patch changes the master netdev to be special, it now
 - no longer is on the list of virtual interfaces, which
   lets me remove a lot of tests for that
 - no longer has sub_if_data attached, since that isn't used

Additionally, this patch changes some vlan/ap mode handling
that is related to these 'bss' pointers described above (but
in the VLAN case they actually make sense because there they
point to the AP they belong to); it also adds some debugging
code to IEEE80211_DEV_TO_SUB_IF to validate it is not called
on the master netdev any more.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

When CONFIG_HOTPLUG=n the following error occures on vmlinux linkage:

`.exit.text' referenced in section `.data' of drivers/built-in.o:
defined in discarded section `.exit.text' of drivers/built-in.o

'rtl8187_disconnect' function marked as __devexit isn't compiled with no
hotplug support. Added __devexit_p macros to fix the problem.
Signed-off-by: Ihar Hrachyshka <ihar.hrachyshka@promwad.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

As soon as an interface is enabled, and that interface is in adhoc or master mode,
the device will start raising beacondone interrupts. But before the first interrupt is
raised, mac80211 will probably not have send any beacons to the device yet, which
results in a NULL pointer error when the skb is being freed.

Note that the "raise beacondone interrupts without a beacon" is also a bug,
and will be addressed later. The more important bug however is preventing
the NULL pointer failt itself, since there might be other conditions that could trigger
it as well.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This patch implements the power management routines wireless extensions
for mac80211.
For now we only support switching PS mode between on and off.
Signed-off-by: Samuel Ortiz <sameo@openedhand.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This corrects an error in the computation of the open loss interval I_0:
  * the interval length is (highest_seqno - start_seqno) + 1
  * and not (highest_seqno - start_seqno).

This condition was not fully clear in RFC 3448, but reflects the current
revision state of rfc3448bis and is also consistent with RFC 4340, 6.1.1.

Further changes:
----------------
 * variable renamed due to line length constraints;
 * explicit typecast to `s64' to avoid implicit signed/unsigned casting.
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>