A previous change to fix checks for NL80211_MESHCONF_HT_OPMODE
missed setting the flag when replacing FILL_IN_MESH_PARAM_IF_SET
with checking codes. This results in dropping the received HT
operation value when called by nl80211_update_mesh_config(). Fix
this by setting the flag properly.

Fixes: 9757235f ("nl80211: correct checks for NL80211_MESHCONF_HT_OPMODE value")
Signed-off-by: Masashi Honma <masashi.honma@gmail.com>
[rewrite commit message to use Fixes: line]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

The function ieee80211_ie_split_vendor doesn't return 0 on errors. Instead
it returns any offset < ielen when WLAN_EID_VENDOR_SPECIFIC is found. The
return value in mesh_add_vendor_ies must therefore be checked against
ifmsh->ie_len and not 0. Otherwise all ifmsh->ie starting with
WLAN_EID_VENDOR_SPECIFIC will be rejected.

Fixes: 082ebb0c ("mac80211: fix mesh beacon format")
Signed-off-by: Thorsten Horstmann <thorsten@defutech.de>
Signed-off-by: Mathias Kretschmer <mathias.kretschmer@fit.fraunhofer.de>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
[sven@narfation.org: Add commit message]
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

The skcipher could have been of the async variant which may return from
skcipher_encrypt() with -EINPROGRESS after having queued the request.
The FILS AEAD implementation here does not have code for dealing with
that possibility, so allocate a sync cipher explicitly to avoid
potential issues with hardware accelerators.

This is based on the patch sent out by Ard.

Fixes: 39404fee ("mac80211: FILS AEAD protection for station mode association frames")
Reported-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Incorrect num_elem parameter value (1 vs. 5) was used in the
aes_siv_encrypt() call. This resulted in only the first one of the five
AAD vectors to SIV getting included in calculation. This does not
protect all the contents correctly and would not interoperate with a
standard compliant implementation.

Fix this by using the correct number. A matching fix is needed in the AP
side (hostapd) to get FILS authentication working properly.

Fixes: 39404fee ("mac80211: FILS AEAD protection for station mode association frames")
Reported-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Andrey Konovalov reported out of bound accesses in ip6gre_err()

If GRE flags contains GRE_KEY, the following expression
*(((__be32 *)p) + (grehlen / 4) - 1)

accesses data ~40 bytes after the expected point, since
grehlen includes the size of IPv6 headers.

Let's use a "struct gre_base_hdr *greh" pointer to make this
code more readable.

p[1] becomes greh->protocol.
grhlen is the GRE header length.

Fixes: c12b395a ("gre: Support GRE over IPv6")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Andrey Konovalov <andreyknvl@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

syzkaller found another out of bound access in ip_options_compile(),
or more exactly in cipso_v4_validate()

Fixes: 20e2a864 ("cipso: handle CIPSO options correctly when NetLabel is disabled")
Fixes: 446fda4f ("[NetLabel]: CIPSOv4 engine")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Dmitry Vyukov  <dvyukov@google.com>
Cc: Paul Moore <paul@paul-moore.com>
Acked-by: Paul Moore <paul@paul-moore.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Andrey Konovalov got crashes in __ip_options_echo() when a NULL skb->dst
is accessed.

ipv4_pktinfo_prepare() should not drop the dst if (evil) IP options
are present.

We could refine the test to the presence of ts_needtime or srr,
but IP options are not often used, so let's be conservative.

Thanks to syzkaller team for finding this bug.

Fixes: d826eb14 ("ipv4: PKTINFO doesnt need dst reference")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Andrey Konovalov <andreyknvl@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Dmitry reported a warning [1] showing that we were calling
net_disable_timestamp() -> static_key_slow_dec() from a non
process context.

Grabbing a mutex while holding a spinlock or rcu_read_lock()
is not allowed.

As Cong suggested, we now use a work queue.

It is possible netstamp_clear() exits while netstamp_needed_deferred
is not zero, but it is probably not worth trying to do better than that.

netstamp_needed_deferred atomic tracks the exact number of deferred
decrements.

[1]
[ INFO: suspicious RCU usage. ]
4.10.0-rc5+ #192 Not tainted
-------------------------------
./include/linux/rcupdate.h:561 Illegal context switch in RCU read-side
critical section!

other info that might help us debug this:

rcu_scheduler_active = 2, debug_locks = 0
2 locks held by syz-executor14/23111:
 #0:  (sk_lock-AF_INET6){+.+.+.}, at: [<ffffffff83a35c35>] lock_sock
include/net/sock.h:1454 [inline]
 #0:  (sk_lock-AF_INET6){+.+.+.}, at: [<ffffffff83a35c35>]
rawv6_sendmsg+0x1e65/0x3ec0 net/ipv6/raw.c:919
 #1:  (rcu_read_lock){......}, at: [<ffffffff83ae2678>] nf_hook
include/linux/netfilter.h:201 [inline]
 #1:  (rcu_read_lock){......}, at: [<ffffffff83ae2678>]
__ip6_local_out+0x258/0x840 net/ipv6/output_core.c:160

stack backtrace:
CPU: 2 PID: 23111 Comm: syz-executor14 Not tainted 4.10.0-rc5+ #192
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS Bochs
01/01/2011
Call Trace:
 __dump_stack lib/dump_stack.c:15 [inline]
 dump_stack+0x2ee/0x3ef lib/dump_stack.c:51
 lockdep_rcu_suspicious+0x139/0x180 kernel/locking/lockdep.c:4452
 rcu_preempt_sleep_check include/linux/rcupdate.h:560 [inline]
 ___might_sleep+0x560/0x650 kernel/sched/core.c:7748
 __might_sleep+0x95/0x1a0 kernel/sched/core.c:7739
 mutex_lock_nested+0x24f/0x1730 kernel/locking/mutex.c:752
 atomic_dec_and_mutex_lock+0x119/0x160 kernel/locking/mutex.c:1060
 __static_key_slow_dec+0x7a/0x1e0 kernel/jump_label.c:149
 static_key_slow_dec+0x51/0x90 kernel/jump_label.c:174
 net_disable_timestamp+0x3b/0x50 net/core/dev.c:1728
 sock_disable_timestamp+0x98/0xc0 net/core/sock.c:403
 __sk_destruct+0x27d/0x6b0 net/core/sock.c:1441
 sk_destruct+0x47/0x80 net/core/sock.c:1460
 __sk_free+0x57/0x230 net/core/sock.c:1468
 sock_wfree+0xae/0x120 net/core/sock.c:1645
 skb_release_head_state+0xfc/0x200 net/core/skbuff.c:655
 skb_release_all+0x15/0x60 net/core/skbuff.c:668
 __kfree_skb+0x15/0x20 net/core/skbuff.c:684
 kfree_skb+0x16e/0x4c0 net/core/skbuff.c:705
 inet_frag_destroy+0x121/0x290 net/ipv4/inet_fragment.c:304
 inet_frag_put include/net/inet_frag.h:133 [inline]
 nf_ct_frag6_gather+0x1106/0x3840
net/ipv6/netfilter/nf_conntrack_reasm.c:617
 ipv6_defrag+0x1be/0x2b0 net/ipv6/netfilter/nf_defrag_ipv6_hooks.c:68
 nf_hook_entry_hookfn include/linux/netfilter.h:102 [inline]
 nf_hook_slow+0xc3/0x290 net/netfilter/core.c:310
 nf_hook include/linux/netfilter.h:212 [inline]
 __ip6_local_out+0x489/0x840 net/ipv6/output_core.c:160
 ip6_local_out+0x2d/0x170 net/ipv6/output_core.c:170
 ip6_send_skb+0xa1/0x340 net/ipv6/ip6_output.c:1722
 ip6_push_pending_frames+0xb3/0xe0 net/ipv6/ip6_output.c:1742
 rawv6_push_pending_frames net/ipv6/raw.c:613 [inline]
 rawv6_sendmsg+0x2d1a/0x3ec0 net/ipv6/raw.c:927
 inet_sendmsg+0x164/0x5b0 net/ipv4/af_inet.c:744
 sock_sendmsg_nosec net/socket.c:635 [inline]
 sock_sendmsg+0xca/0x110 net/socket.c:645
 sock_write_iter+0x326/0x600 net/socket.c:848
 do_iter_readv_writev+0x2e3/0x5b0 fs/read_write.c:695
 do_readv_writev+0x42c/0x9b0 fs/read_write.c:872
 vfs_writev+0x87/0xc0 fs/read_write.c:911
 do_writev+0x110/0x2c0 fs/read_write.c:944
 SYSC_writev fs/read_write.c:1017 [inline]
 SyS_writev+0x27/0x30 fs/read_write.c:1014
 entry_SYSCALL_64_fastpath+0x1f/0xc2
RIP: 0033:0x445559
RSP: 002b:00007f6f46fceb58 EFLAGS: 00000292 ORIG_RAX: 0000000000000014
RAX: ffffffffffffffda RBX: 0000000000000005 RCX: 0000000000445559
RDX: 0000000000000001 RSI: 0000000020f1eff0 RDI: 0000000000000005
RBP: 00000000006e19c0 R08: 0000000000000000 R09: 0000000000000000
R10: 0000000000000000 R11: 0000000000000292 R12: 0000000000700000
R13: 0000000020f59000 R14: 0000000000000015 R15: 0000000000020400
BUG: sleeping function called from invalid context at
kernel/locking/mutex.c:752
in_atomic(): 1, irqs_disabled(): 0, pid: 23111, name: syz-executor14
INFO: lockdep is turned off.
CPU: 2 PID: 23111 Comm: syz-executor14 Not tainted 4.10.0-rc5+ #192
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS Bochs
01/01/2011
Call Trace:
 __dump_stack lib/dump_stack.c:15 [inline]
 dump_stack+0x2ee/0x3ef lib/dump_stack.c:51
 ___might_sleep+0x47e/0x650 kernel/sched/core.c:7780
 __might_sleep+0x95/0x1a0 kernel/sched/core.c:7739
 mutex_lock_nested+0x24f/0x1730 kernel/locking/mutex.c:752
 atomic_dec_and_mutex_lock+0x119/0x160 kernel/locking/mutex.c:1060
 __static_key_slow_dec+0x7a/0x1e0 kernel/jump_label.c:149
 static_key_slow_dec+0x51/0x90 kernel/jump_label.c:174
 net_disable_timestamp+0x3b/0x50 net/core/dev.c:1728
 sock_disable_timestamp+0x98/0xc0 net/core/sock.c:403
 __sk_destruct+0x27d/0x6b0 net/core/sock.c:1441
 sk_destruct+0x47/0x80 net/core/sock.c:1460
 __sk_free+0x57/0x230 net/core/sock.c:1468
 sock_wfree+0xae/0x120 net/core/sock.c:1645
 skb_release_head_state+0xfc/0x200 net/core/skbuff.c:655
 skb_release_all+0x15/0x60 net/core/skbuff.c:668
 __kfree_skb+0x15/0x20 net/core/skbuff.c:684
 kfree_skb+0x16e/0x4c0 net/core/skbuff.c:705
 inet_frag_destroy+0x121/0x290 net/ipv4/inet_fragment.c:304
 inet_frag_put include/net/inet_frag.h:133 [inline]
 nf_ct_frag6_gather+0x1106/0x3840
net/ipv6/netfilter/nf_conntrack_reasm.c:617
 ipv6_defrag+0x1be/0x2b0 net/ipv6/netfilter/nf_defrag_ipv6_hooks.c:68
 nf_hook_entry_hookfn include/linux/netfilter.h:102 [inline]
 nf_hook_slow+0xc3/0x290 net/netfilter/core.c:310
 nf_hook include/linux/netfilter.h:212 [inline]
 __ip6_local_out+0x489/0x840 net/ipv6/output_core.c:160
 ip6_local_out+0x2d/0x170 net/ipv6/output_core.c:170
 ip6_send_skb+0xa1/0x340 net/ipv6/ip6_output.c:1722
 ip6_push_pending_frames+0xb3/0xe0 net/ipv6/ip6_output.c:1742
 rawv6_push_pending_frames net/ipv6/raw.c:613 [inline]
 rawv6_sendmsg+0x2d1a/0x3ec0 net/ipv6/raw.c:927
 inet_sendmsg+0x164/0x5b0 net/ipv4/af_inet.c:744
 sock_sendmsg_nosec net/socket.c:635 [inline]
 sock_sendmsg+0xca/0x110 net/socket.c:645
 sock_write_iter+0x326/0x600 net/socket.c:848
 do_iter_readv_writev+0x2e3/0x5b0 fs/read_write.c:695
 do_readv_writev+0x42c/0x9b0 fs/read_write.c:872
 vfs_writev+0x87/0xc0 fs/read_write.c:911
 do_writev+0x110/0x2c0 fs/read_write.c:944
 SYSC_writev fs/read_write.c:1017 [inline]
 SyS_writev+0x27/0x30 fs/read_write.c:1014
 entry_SYSCALL_64_fastpath+0x1f/0xc2
RIP: 0033:0x445559

Fixes: b90e5794 ("net: dont call jump_label_dec from irq context")
Suggested-by: Cong Wang <xiyou.wangcong@gmail.com>
Reported-by: Dmitry Vyukov <dvyukov@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

If ->get_regs_len() callback return 0, we allocate 0 bytes of memory,
what print ugly warning in dmesg, which can be found further below.

This happen on mac80211 devices where ieee80211_get_regs_len() just
return 0 and driver only fills ethtool_regs structure and actually
do not provide any dump. However I assume this can happen on other
drivers i.e. when for some devices driver provide regs dump and for
others do not. Hence preventing to to print warning in ethtool code
seems to be reasonable.

ethtool: vmalloc: allocation failure: 0 bytes, mode:0x24080c2(GFP_KERNEL|__GFP_HIGHMEM|__GFP_ZERO)
<snip>
Call Trace:
[<ffffffff813bde47>] dump_stack+0x63/0x8c
[<ffffffff811b0a1f>] warn_alloc+0x13f/0x170
[<ffffffff811f0476>] __vmalloc_node_range+0x1e6/0x2c0
[<ffffffff811f0874>] vzalloc+0x54/0x60
[<ffffffff8169986c>] dev_ethtool+0xb4c/0x1b30
[<ffffffff816adbb1>] dev_ioctl+0x181/0x520
[<ffffffff816714d2>] sock_do_ioctl+0x42/0x50
<snip>
Mem-Info:
active_anon:435809 inactive_anon:173951 isolated_anon:0
 active_file:835822 inactive_file:196932 isolated_file:0
 unevictable:0 dirty:8 writeback:0 unstable:0
 slab_reclaimable:157732 slab_unreclaimable:10022
 mapped:83042 shmem:306356 pagetables:9507 bounce:0
 free:130041 free_pcp:1080 free_cma:0
Node 0 active_anon:1743236kB inactive_anon:695804kB active_file:3343288kB inactive_file:787728kB unevictable:0kB isolated(anon):0kB isolated(file):0kB mapped:332168kB dirty:32kB writeback:0kB shmem:0kB shmem_thp: 0kB shmem_pmdmapped: 0kB anon_thp: 1225424kB writeback_tmp:0kB unstable:0kB pages_scanned:0 all_unreclaimable? no
Node 0 DMA free:15900kB min:136kB low:168kB high:200kB active_anon:0kB inactive_anon:0kB active_file:0kB inactive_file:0kB unevictable:0kB writepending:0kB present:15984kB managed:15900kB mlocked:0kB slab_reclaimable:0kB slab_unreclaimable:0kB kernel_stack:0kB pagetables:0kB bounce:0kB free_pcp:0kB local_pcp:0kB free_cma:0kB
lowmem_reserve[]: 0 3187 7643 7643
Node 0 DMA32 free:419732kB min:28124kB low:35152kB high:42180kB active_anon:541180kB inactive_anon:248988kB active_file:1466388kB inactive_file:389632kB unevictable:0kB writepending:0kB present:3370280kB managed:3290932kB mlocked:0kB slab_reclaimable:217184kB slab_unreclaimable:4180kB kernel_stack:160kB pagetables:984kB bounce:0kB free_pcp:2236kB local_pcp:660kB free_cma:0kB
lowmem_reserve[]: 0 0 4456 4456
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In the latest version of the IPv6 Segment Routing IETF draft [1] the
cleanup flag is removed and the flags field length is shrunk from 16 bits
to 8 bits. As a consequence, the input of the HMAC computation is modified
in a non-backward compatible way by covering the whole octet of flags
instead of only the cleanup bit. As such, if an implementation compatible
with the latest draft computes the HMAC of an SRH who has other flags set
to 1, then the HMAC result would differ from the current implementation.

This patch carries those modifications to prevent conflict with other
implementations of IPv6 SR.

[1] https://tools.ietf.org/html/draft-ietf-6man-segment-routing-header-05Signed-off-by: David Lebrun <david.lebrun@uclouvain.be>
Signed-off-by: David S. Miller <davem@davemloft.net>

There is currently no reference count being held on the PHY driver,
which makes it possible to remove the PHY driver module while the PHY
state machine is running and polling the PHY. This could cause crashes
similar to this one to show up:

[   43.361162] BUG: unable to handle kernel NULL pointer dereference at 0000000000000140
[   43.361162] IP: phy_state_machine+0x32/0x490
[   43.361162] PGD 59dc067
[   43.361162] PUD 0
[   43.361162]
[   43.361162] Oops: 0000 [#1] SMP
[   43.361162] Modules linked in: dsa_loop [last unloaded: broadcom]
[   43.361162] CPU: 0 PID: 1299 Comm: kworker/0:3 Not tainted 4.10.0-rc5+ #415
[   43.361162] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996),
BIOS Ubuntu-1.8.2-1ubuntu2 04/01/2014
[   43.361162] Workqueue: events_power_efficient phy_state_machine
[   43.361162] task: ffff880006782b80 task.stack: ffffc90000184000
[   43.361162] RIP: 0010:phy_state_machine+0x32/0x490
[   43.361162] RSP: 0018:ffffc90000187e18 EFLAGS: 00000246
[   43.361162] RAX: 0000000000000000 RBX: ffff8800059e53c0 RCX:
ffff880006a15c60
[   43.361162] RDX: ffff880006782b80 RSI: 0000000000000000 RDI:
ffff8800059e5428
[   43.361162] RBP: ffffc90000187e48 R08: ffff880006a15c40 R09:
0000000000000000
[   43.361162] R10: 0000000000000000 R11: 0000000000000000 R12:
ffff8800059e5428
[   43.361162] R13: ffff8800059e5000 R14: 0000000000000000 R15:
ffff880006a15c40
[   43.361162] FS:  0000000000000000(0000) GS:ffff880006a00000(0000)
knlGS:0000000000000000
[   43.361162] CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[   43.361162] CR2: 0000000000000140 CR3: 0000000005979000 CR4:
00000000000006f0
[   43.361162] Call Trace:
[   43.361162]  process_one_work+0x1b4/0x3e0
[   43.361162]  worker_thread+0x43/0x4d0
[   43.361162]  ? __schedule+0x17f/0x4e0
[   43.361162]  kthread+0xf7/0x130
[   43.361162]  ? process_one_work+0x3e0/0x3e0
[   43.361162]  ? kthread_create_on_node+0x40/0x40
[   43.361162]  ret_from_fork+0x29/0x40
[   43.361162] Code: 56 41 55 41 54 4c 8d 67 68 53 4c 8d af 40 fc ff ff
48 89 fb 4c 89 e7 48 83 ec 08 e8 c9 9d 27 00 48 8b 83 60 ff ff ff 44 8b
73 98 <48> 8b 90 40 01 00 00 44 89 f0 48 85 d2 74 08 4c 89 ef ff d2 8b

Keep references on the PHY driver module right before we are going to
utilize it in phy_attach_direct(), and conversely when we don't use it
anymore in phy_detach().
Signed-off-by: Mao Wenan <maowenan@huawei.com>
[florian: rebase, rework commit message]
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Martin KaFai Lau says:

====================
mlx4: Misc bug fixes after reinitializing queues

This patchset fixes misc bugs after reinitializing
queues (e.g. by ethtool -L).

v2:
* Add another fix to mem leak in tx_ring[t] and tx_cq[t]
* In mlx4_en_try_alloc_resources(),
  move all xdp_prog logic after calling mlx4_en_alloc_resources()
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

After calling mlx4_en_try_alloc_resources (e.g. by changing the
number of rx-queues with ethtool -L), the existing xdp_prog becomes
inactive.

The bug is that the xdp_prog ptr has not been carried over from
the old rx-queues to the new rx-queues

Fixes: 47a38e15 ("net/mlx4_en: add support for fast rx drop bpf program")
Cc: Brenden Blanco <bblanco@plumgrid.com>
Cc: Saeed Mahameed <saeedm@mellanox.com>
Cc: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Martin KaFai Lau <kafai@fb.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In mlx4_en_update_priv(), dst->tx_ring[t] and dst->tx_cq[t]
are over-written by src->tx_ring[t] and src->tx_cq[t] without
first calling kfree.

One of the reproducible code paths is by doing 'ethtool -L'.

The fix is to do the kfree in mlx4_en_free_resources().

Here is the kmemleak report:
unreferenced object 0xffff880841211800 (size 2048):
  comm "ethtool", pid 3096, jiffies 4294716940 (age 528.353s)
  hex dump (first 32 bytes):
    00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00  ................
    00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00  ................
  backtrace:
    [<ffffffff81930718>] kmemleak_alloc+0x28/0x50
    [<ffffffff8120b213>] kmem_cache_alloc_trace+0x103/0x260
    [<ffffffff8170e0a8>] mlx4_en_try_alloc_resources+0x118/0x1a0
    [<ffffffff817065a9>] mlx4_en_set_ringparam+0x169/0x210
    [<ffffffff818040c5>] dev_ethtool+0xae5/0x2190
    [<ffffffff8181b898>] dev_ioctl+0x168/0x6f0
    [<ffffffff817d7a72>] sock_do_ioctl+0x42/0x50
    [<ffffffff817d819b>] sock_ioctl+0x21b/0x2d0
    [<ffffffff81247a73>] do_vfs_ioctl+0x93/0x6a0
    [<ffffffff812480f9>] SyS_ioctl+0x79/0x90
    [<ffffffff8193d7ea>] entry_SYSCALL_64_fastpath+0x18/0xad
    [<ffffffffffffffff>] 0xffffffffffffffff
unreferenced object 0xffff880841213000 (size 2048):
  comm "ethtool", pid 3096, jiffies 4294716940 (age 528.353s)
  hex dump (first 32 bytes):
    00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00  ................
    00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00  ................
  backtrace:
    [<ffffffff81930718>] kmemleak_alloc+0x28/0x50
    [<ffffffff8120b213>] kmem_cache_alloc_trace+0x103/0x260
    [<ffffffff8170e0cb>] mlx4_en_try_alloc_resources+0x13b/0x1a0
    [<ffffffff817065a9>] mlx4_en_set_ringparam+0x169/0x210
    [<ffffffff818040c5>] dev_ethtool+0xae5/0x2190
    [<ffffffff8181b898>] dev_ioctl+0x168/0x6f0
    [<ffffffff817d7a72>] sock_do_ioctl+0x42/0x50
    [<ffffffff817d819b>] sock_ioctl+0x21b/0x2d0
    [<ffffffff81247a73>] do_vfs_ioctl+0x93/0x6a0
    [<ffffffff812480f9>] SyS_ioctl+0x79/0x90
    [<ffffffff8193d7ea>] entry_SYSCALL_64_fastpath+0x18/0xad
    [<ffffffffffffffff>] 0xffffffffffffffff

(gdb) list *mlx4_en_try_alloc_resources+0x118
0xffffffff8170e0a8 is in mlx4_en_try_alloc_resources (drivers/net/ethernet/mellanox/mlx4/en_netdev.c:2145).
2140                    if (!dst->tx_ring_num[t])
2141                            continue;
2142
2143                    dst->tx_ring[t] = kzalloc(sizeof(struct mlx4_en_tx_ring *) *
2144                                              MAX_TX_RINGS, GFP_KERNEL);
2145                    if (!dst->tx_ring[t])
2146                            goto err_free_tx;
2147
2148                    dst->tx_cq[t] = kzalloc(sizeof(struct mlx4_en_cq *) *
2149                                            MAX_TX_RINGS, GFP_KERNEL);
(gdb) list *mlx4_en_try_alloc_resources+0x13b
0xffffffff8170e0cb is in mlx4_en_try_alloc_resources (drivers/net/ethernet/mellanox/mlx4/en_netdev.c:2150).
2145                    if (!dst->tx_ring[t])
2146                            goto err_free_tx;
2147
2148                    dst->tx_cq[t] = kzalloc(sizeof(struct mlx4_en_cq *) *
2149                                            MAX_TX_RINGS, GFP_KERNEL);
2150                    if (!dst->tx_cq[t]) {
2151                            kfree(dst->tx_ring[t]);
2152                            goto err_free_tx;
2153                    }
2154            }

Fixes: ec25bc04 ("net/mlx4_en: Add resilience in low memory systems")
Cc: Eugenia Emantayev <eugenia@mellanox.com>
Cc: Saeed Mahameed <saeedm@mellanox.com>
Cc: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Martin KaFai Lau <kafai@fb.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Pull networking fixes from David Miller:

 1) Fix handling of interrupt status in stmmac driver. Just because we
    have masked the event from generating interrupts, doesn't mean the
    bit won't still be set in the interrupt status register. From Alexey
    Brodkin.

 2) Fix DMA API debugging splats in gianfar driver, from Arseny Solokha.

 3) Fix off-by-one error in __ip6_append_data(), from Vlad Yasevich.

 4) cls_flow does not match on icmpv6 codes properly, from Simon Horman.

 5) Initial MAC address can be set incorrectly in some scenerios, from
    Ivan Vecera.

 6) Packet header pointer arithmetic fix in ip6_tnl_parse_tlv_end_lim(),
    from Dan Carpenter.

 7) Fix divide by zero in __tcp_select_window(), from Eric Dumazet.

 8) Fix crash in iwlwifi when unregistering thermal zone, from Jens
    Axboe.

 9) Check for DMA mapping errors in starfire driver, from Alexey
    Khoroshilov.

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (31 commits)
  tcp: fix 0 divide in __tcp_select_window()
  ipv6: pointer math error in ip6_tnl_parse_tlv_enc_lim()
  net: fix ndo_features_check/ndo_fix_features comment ordering
  net/sched: matchall: Fix configuration race
  be2net: fix initial MAC setting
  ipv6: fix flow labels when the traffic class is non-0
  net: thunderx: avoid dereferencing xcv when NULL
  net/sched: cls_flower: Correct matching on ICMPv6 code
  ipv6: Paritially checksum full MTU frames
  net/mlx4_core: Avoid command timeouts during VF driver device shutdown
  gianfar: synchronize DMA API usage by free_skb_rx_queue w/ gfar_new_page
  net: ethtool: add support for 2500BaseT and 5000BaseT link modes
  can: bcm: fix hrtimer/tasklet termination in bcm op removal
  net: adaptec: starfire: add checks for dma mapping errors
  net: phy: micrel: KSZ8795 do not set SUPPORTED_[Asym_]Pause
  can: Fix kernel panic at security_sock_rcv_skb
  net: macb: Fix 64 bit addressing support for GEM
  stmmac: Discard masked flags in interrupt status register
  net/mlx5e: Check ets capability before ets query FW command
  net/mlx5e: Fix update of hash function/key via ethtool
  ...

Pull fscache fixes from Al Viro.

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
  fscache: Fix dead object requeue
  fscache: Clear outstanding writes when disabling a cookie
  FS-Cache: Initialise stores_lock in netfs cookie

syszkaller fuzzer was able to trigger a divide by zero, when
TCP window scaling is not enabled.

SO_RCVBUF can be used not only to increase sk_rcvbuf, also
to decrease it below current receive buffers utilization.

If mss is negative or 0, just return a zero TCP window.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Dmitry Vyukov  <dvyukov@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Casting is a high precedence operation but "off" and "i" are in terms of
bytes so we need to have some parenthesis here.

Fixes: fbfa743a ("ipv6: fix ip6_tnl_parse_tlv_enc_lim()")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Pull crypto fixes from Herbert Xu:
 "This fixes a bug in CBC/CTR on ARM64 that breaks chaining as well as a
  bug in the core API that causes registration failures when a driver
  unloads and then reloads an algorithm"

* 'linus' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
  crypto: arm64/aes-blk - honour iv_out requirement in CBC and CTR modes
  crypto: api - Clear CRYPTO_ALG_DEAD bit before registering an alg

Pull dmaengine fixes from Vinod Koul:
 "A couple of fixes showed up late in the cycle so sending them up and
  sending early in the week and not on Friday :).

  They fix a double lock in pl330 driver and runtime pm fixes for cppi
  driver"

* tag 'dmaengine-fix-4.10-rc7' of git://git.infradead.org/users/vkoul/slave-dma:
  dmaengine: pl330: fix double lock
  dmaengine: cppi41: Clean up pointless warnings
  dmaengine: cppi41: Fix oops in cppi41_runtime_resume
  dmaengine: cppi41: Fix runtime PM timeouts with USB mass storage

Commit cdba756f ("net: move ndo_features_check() close to
ndo_start_xmit()") inadvertently moved the doc comment for
.ndo_fix_features instead of .ndo_features_check. Fix the comment
ordering.

Fixes: cdba756f ("net: move ndo_features_check() close to ndo_start_xmit()")
Signed-off-by: Dimitris Michailidis <dmichail@google.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In the current version, the matchall internal state is split into two
structs: cls_matchall_head and cls_matchall_filter. This makes little
sense, as matchall instance supports only one filter, and there is no
situation where one exists and the other does not. In addition, that led
to some races when filter was deleted while packet was processed.

Unify that two structs into one, thus simplifying the process of matchall
creation and deletion. As a result, the new, delete and get callbacks have
a dummy implementation where all the work is done in destroy and change
callbacks, as was done in cls_cgroup.

Fixes: bf3994d2 ("net/sched: introduce Match-all classifier")
Reported-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Yotam Gigi <yotamg@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Pull pin control fixes from Linus Walleij:
 "Another week, another set of pin control fixes. The subsystem has seen
  high patch-spot activity recently.

  The majority of the patches are for Intel, I vaguely think it mostly
  concern phones, tablets and maybe chromebooks and even laptops with
  this Intel Atom family chips.

  Driver fixes only:

   - one fix to the Berlin driver making the SD card work fully again.

   - one fix to the Allwinner/sunxi bias function: one premature change
     needs to be partially reverted.

   - the remaining four patches are to Intel embedded SoCs: baytrail
     (three patches) and merrifield (one patch): register access
     debounce fixes and a missing spinlock"

* tag 'pinctrl-v4.10-4' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl:
  pinctrl: baytrail: Add missing spinlock usage in byt_gpio_irq_handler
  pinctrl: baytrail: Debounce register is one per community
  pinctrl: baytrail: Rectify debounce support (part 2)
  pinctrl: intel: merrifield: Add missed check in mrfld_config_set()
  pinctrl: sunxi: Don't enforce bias disable (for now)
  pinctrl: berlin-bg4ct: fix the value for "sd1a" of pin SCRD0_CRD_PRES

Recent commit 34393529 ("be2net: fix MAC addr setting on privileged
BE3 VFs") allows privileged BE3 VFs to set its MAC address during
initialization. Although the initial MAC for such VFs is already
programmed by parent PF the subsequent setting performed by VF is OK,
but in certain cases (after fresh boot) this command in VF can fail.

The MAC should be initialized only when:
1) no MAC is programmed (always except BE3 VFs during first init)
2) programmed MAC is different from requested (e.g. MAC is set when
   interface is down). In this case the initial MAC programmed by PF
   needs to be deleted.

The adapter->dev_mac contains MAC address currently programmed in HW so
it should be zeroed when the MAC is deleted from HW and should not be
filled when MAC is set when interface is down in be_mac_addr_set() as
no programming is performed in this case.

Example of failure without the fix (immediately after fresh boot):

# ip link set eth0 up  <- eth0 is BE3 PF
be2net 0000:01:00.0 eth0: Link is Up

# echo 1 > /sys/class/net/eth0/device/sriov_numvfs  <- Create 1 VF
...
be2net 0000:01:04.0: Emulex OneConnect(be3): VF  port 0

# ip link set eth8 up  <- eth8 is created privileged VF
be2net 0000:01:04.0: opcode 59-1 failed:status 1-76
RTNETLINK answers: Input/output error

# echo 0 > /sys/class/net/eth0/device/sriov_numvfs  <- Delete VF
iommu: Removing device 0000:01:04.0 from group 33
...

# echo 1 > /sys/class/net/eth0/device/sriov_numvfs  <- Create it again
iommu: Removing device 0000:01:04.0 from group 33
...

# ip link set eth8 up
be2net 0000:01:04.0 eth8: Link is Up

Initialization is now OK.

v2 - Corrected the comment and condition check suggested by Suresh & Harsha

Fixes: 34393529 ("be2net: fix MAC addr setting on privileged BE3 VFs")
Cc: Sathya Perla <sathya.perla@broadcom.com>
Cc: Ajit Khaparde <ajit.khaparde@broadcom.com>
Cc: Sriharsha Basavapatna <sriharsha.basavapatna@broadcom.com>
Cc: Somnath Kotur <somnath.kotur@broadcom.com>
Signed-off-by: Ivan Vecera <cera@cera.cz>
Acked-by: Sriharsha Basavapatna <sriharsha.basavapatna@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Pull tracing fix from Steven Rostedt:
 "It was reported to me that the thread created by the hwlat tracer does
  not migrate after the first instance. I found that there was as small
  bug in the logic, and fixed it. It's minor, but should be fixed
  regardless. There's not much impact outside the hwlat tracer"

* tag 'trace-4.10-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace:
  tracing: Fix hwlat kthread migration

Pull input subsystem fixes from Dmitry Torokhov:
 "A fix for a crash in the wm97xx driver and synaptics-rmi4 will stop
  throwing erroneous warnings."

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
  Input: synaptics-rmi4 - fix reversed conditions in enable/disable_irq_wake
  Input: wm97xx - make missing platform data non-fatal

Pull cgroup fix from Tejun Heo:
 "The cgroup creation path was getting the order of operations wrong and
  exposing cgroups which don't have their names set yet to controllers
  which can lead to NULL derefs.

  This contains the fix for the bug"

* 'for-4.10-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/cgroup:
  cgroup: don't online subsystems before cgroup_name/path() are operational

Pull percpu fix from Tejun Heo:
 "Douglas found and fixed a ref leak bug in percpu_ref_tryget[_live]().

  The bug is caused by storing the return value of atomic_long_inc_not_zero()
  into an int temp variable before returning it as a bool. The interim
  cast to int loses the upper bits and can lead to false negatives. As
  percpu_ref uses a high bit to mark a draining counter, this can happen
  relatively easily.

  Fixed by using bool for the temp variable"

* 'for-4.10-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/percpu:
  percpu-refcount: fix reference leak during percpu-atomic transition

Pull libata fixes from Tejun Heo:
 "Three libata fixes: an error handling fix, blacklist addition for
  another fallout from upping the default max sectors, and fix for a
  sense data reporting bug which affects new harddrives which can report
  sense data"

* 'for-4.10-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata:
  ata: sata_mv:- Handle return value of devm_ioremap.
  libata: Fix ATA request sense
  libata: apply MAX_SEC_1024 to all CX1-JB*-HP devices

Pull HID fixes from Jiri Kosina:

 - regression fix (sleeping while atomic) for cp2112, from Johan Hovold

 - regression fix for proximity handling under certain circumstances in
   Wacom driver, from Jason Gerecke

 - functional fix for Logitech Rumblepad 2, from Ardinartsev Nikita

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid:
  HID: cp2112: fix gpio-callback error handling
  HID: cp2112: fix sleep-while-atomic
  HID: hid-lg: Fix immediate disconnection of Logitech Rumblepad 2
  HID: usbhid: Quirk a AMI virtual mouse and keyboard with ALWAYS_POLL
  HID: wacom: Fix poor prox handling in 'wacom_pl_irq'

Pull cifs fix from Steve French:
 "A small cifs fix for stable"

* 'for-next' of git://git.samba.org/sfrench/cifs-2.6:
  cifs: initialize file_info_lock

Under some circumstances, an fscache object can become queued such that it
fscache_object_work_func() can be called once the object is in the
OBJECT_DEAD state.  This results in the kernel oopsing when it tries to
invoke the handler for the state (which is hard coded to 0x2).

The way this comes about is something like the following:

 (1) The object dispatcher is processing a work state for an object.  This
     is done in workqueue context.

 (2) An out-of-band event comes in that isn't masked, causing the object to
     be queued, say EV_KILL.

 (3) The object dispatcher finishes processing the current work state on
     that object and then sees there's another event to process, so,
     without returning to the workqueue core, it processes that event too.
     It then follows the chain of events that initiates until we reach
     OBJECT_DEAD without going through a wait state (such as
     WAIT_FOR_CLEARANCE).

     At this point, object->events may be 0, object->event_mask will be 0
     and oob_event_mask will be 0.

 (4) The object dispatcher returns to the workqueue processor, and in due
     course, this sees that the object's work item is still queued and
     invokes it again.

 (5) The current state is a work state (OBJECT_DEAD), so the dispatcher
     jumps to it - resulting in an OOPS.

When I'm seeing this, the work state in (1) appears to have been either
LOOK_UP_OBJECT or CREATE_OBJECT (object->oob_table is
fscache_osm_lookup_oob).

The window for (2) is very small:

 (A) object->event_mask is cleared whilst the event dispatch process is
     underway - though there's no memory barrier to force this to the top
     of the function.

     The window, therefore is from the time the object was selected by the
     workqueue processor and made requeueable to the time the mask was
     cleared.

 (B) fscache_raise_event() will only queue the object if it manages to set
     the event bit and the corresponding event_mask bit was set.

     The enqueuement is then deferred slightly whilst we get a ref on the
     object and get the per-CPU variable for workqueue congestion.  This
     slight deferral slightly increases the probability by allowing extra
     time for the workqueue to make the item requeueable.

Handle this by giving the dead state a processor function and checking the
for the dead state address rather than seeing if the processor function is
address 0x2.  The dead state processor function can then set a flag to
indicate that it's occurred and give a warning if it occurs more than once
per object.

If this race occurs, an oops similar to the following is seen (note the RIP
value):

BUG: unable to handle kernel NULL pointer dereference at 0000000000000002
IP: [<0000000000000002>] 0x1
PGD 0
Oops: 0010 [#1] SMP
Modules linked in: ...
CPU: 17 PID: 16077 Comm: kworker/u48:9 Not tainted 3.10.0-327.18.2.el7.x86_64 #1
Hardware name: HP ProLiant DL380 Gen9/ProLiant DL380 Gen9, BIOS P89 12/27/2015
Workqueue: fscache_object fscache_object_work_func [fscache]
task: ffff880302b63980 ti: ffff880717544000 task.ti: ffff880717544000
RIP: 0010:[<0000000000000002>]  [<0000000000000002>] 0x1
RSP: 0018:ffff880717547df8  EFLAGS: 00010202
RAX: ffffffffa0368640 RBX: ffff880edf7a4480 RCX: dead000000200200
RDX: 0000000000000002 RSI: 00000000ffffffff RDI: ffff880edf7a4480
RBP: ffff880717547e18 R08: 0000000000000000 R09: dfc40a25cb3a4510
R10: dfc40a25cb3a4510 R11: 0000000000000400 R12: 0000000000000000
R13: ffff880edf7a4510 R14: ffff8817f6153400 R15: 0000000000000600
FS:  0000000000000000(0000) GS:ffff88181f420000(0000) knlGS:0000000000000000
CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 0000000000000002 CR3: 000000000194a000 CR4: 00000000001407e0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000ffff0ff0 DR7: 0000000000000400
Stack:
 ffffffffa0363695 ffff880edf7a4510 ffff88093f16f900 ffff8817faa4ec00
 ffff880717547e60 ffffffff8109d5db 00000000faa4ec18 0000000000000000
 ffff8817faa4ec18 ffff88093f16f930 ffff880302b63980 ffff88093f16f900
Call Trace:
 [<ffffffffa0363695>] ? fscache_object_work_func+0xa5/0x200 [fscache]
 [<ffffffff8109d5db>] process_one_work+0x17b/0x470
 [<ffffffff8109e4ac>] worker_thread+0x21c/0x400
 [<ffffffff8109e290>] ? rescuer_thread+0x400/0x400
 [<ffffffff810a5acf>] kthread+0xcf/0xe0
 [<ffffffff810a5a00>] ? kthread_create_on_node+0x140/0x140
 [<ffffffff816460d8>] ret_from_fork+0x58/0x90
 [<ffffffff810a5a00>] ? kthread_create_on_node+0x140/0x140
Signed-off-by: David Howells <dhowells@redhat.com>
Acked-by: Jeremy McNicoll <jeremymc@redhat.com>
Tested-by: Frank Sorenson <sorenson@redhat.com>
Tested-by: Benjamin Coddington <bcodding@redhat.com>
Reviewed-by: Benjamin Coddington <bcodding@redhat.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>

fscache_disable_cookie() needs to clear the outstanding writes on the
cookie it's disabling because they cannot be completed after.

Without this, fscache_nfs_open_file() gets stuck because it disables the
cookie when the file is opened for writing but can't uncache the pages till
afterwards - otherwise there's a race between the open routine and anyone
who already has it open R/O and is still reading from it.

Looking in /proc/pid/stack of the offending process shows:

[<ffffffffa0142883>] __fscache_wait_on_page_write+0x82/0x9b [fscache]
[<ffffffffa014336e>] __fscache_uncache_all_inode_pages+0x91/0xe1 [fscache]
[<ffffffffa01740fa>] nfs_fscache_open_file+0x59/0x9e [nfs]
[<ffffffffa01ccf41>] nfs4_file_open+0x17f/0x1b8 [nfsv4]
[<ffffffff8117350e>] do_dentry_open+0x16d/0x2b7
[<ffffffff811743ac>] vfs_open+0x5c/0x65
[<ffffffff81184185>] path_openat+0x785/0x8fb
[<ffffffff81184343>] do_filp_open+0x48/0x9e
[<ffffffff81174710>] do_sys_open+0x13b/0x1cb
[<ffffffff811747b9>] SyS_open+0x19/0x1b
[<ffffffff81001c44>] do_syscall_64+0x80/0x17a
[<ffffffff8165c2da>] return_from_SYSCALL_64+0x0/0x7a
[<ffffffffffffffff>] 0xffffffffffffffff
Reported-by: Jianhong Yin <jiyin@redhat.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Acked-by: Jeff Layton <jlayton@redhat.com>
Acked-by: Steve Dickson <steved@redhat.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>

Initialise the stores_lock in fscache netfs cookies.  Technically, it
shouldn't be necessary, since the netfs cookie is an index and stores no
data, but initialising it anyway adds insignificant overhead.
Signed-off-by: David Howells <dhowells@redhat.com>
Reviewed-by: Jeff Layton <jlayton@redhat.com>
Acked-by: Steve Dickson <steved@redhat.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>

ip6_make_flowlabel() determines the flow label for IPv6 packets. It's
supposed to be passed a flow label, which it returns as is if non-0 and
in some other cases, otherwise it calculates a new value.

The problem is callers often pass a flowi6.flowlabel, which may also
contain traffic class bits. If the traffic class is non-0
ip6_make_flowlabel() mistakes the non-0 it gets as a flow label and
returns the whole thing. Thus it can return a 'flow label' longer than
20b and the low 20b of that is typically 0 resulting in packets with 0
label. Moreover, different packets of a flow may be labeled differently.
For a TCP flow with ECN non-payload and payload packets get different
labels as exemplified by this pair of consecutive packets:

(pure ACK)
Internet Protocol Version 6, Src: 2002:af5:11a3::, Dst: 2002:af5:11a2::
    0110 .... = Version: 6
    .... 0000 0000 .... .... .... .... .... = Traffic Class: 0x00 (DSCP: CS0, ECN: Not-ECT)
        .... 0000 00.. .... .... .... .... .... = Differentiated Services Codepoint: Default (0)
        .... .... ..00 .... .... .... .... .... = Explicit Congestion Notification: Not ECN-Capable Transport (0)
    .... .... .... 0001 1100 1110 0100 1001 = Flow Label: 0x1ce49
    Payload Length: 32
    Next Header: TCP (6)

(payload)
Internet Protocol Version 6, Src: 2002:af5:11a3::, Dst: 2002:af5:11a2::
    0110 .... = Version: 6
    .... 0000 0010 .... .... .... .... .... = Traffic Class: 0x02 (DSCP: CS0, ECN: ECT(0))
        .... 0000 00.. .... .... .... .... .... = Differentiated Services Codepoint: Default (0)
        .... .... ..10 .... .... .... .... .... = Explicit Congestion Notification: ECN-Capable Transport codepoint '10' (2)
    .... .... .... 0000 0000 0000 0000 0000 = Flow Label: 0x00000
    Payload Length: 688
    Next Header: TCP (6)

This patch allows ip6_make_flowlabel() to be passed more than just a
flow label and has it extract the part it really wants. This was simpler
than modifying the callers. With this patch packets like the above become

Internet Protocol Version 6, Src: 2002:af5:11a3::, Dst: 2002:af5:11a2::
    0110 .... = Version: 6
    .... 0000 0000 .... .... .... .... .... = Traffic Class: 0x00 (DSCP: CS0, ECN: Not-ECT)
        .... 0000 00.. .... .... .... .... .... = Differentiated Services Codepoint: Default (0)
        .... .... ..00 .... .... .... .... .... = Explicit Congestion Notification: Not ECN-Capable Transport (0)
    .... .... .... 1010 1111 1010 0101 1110 = Flow Label: 0xafa5e
    Payload Length: 32
    Next Header: TCP (6)

Internet Protocol Version 6, Src: 2002:af5:11a3::, Dst: 2002:af5:11a2::
    0110 .... = Version: 6
    .... 0000 0010 .... .... .... .... .... = Traffic Class: 0x02 (DSCP: CS0, ECN: ECT(0))
        .... 0000 00.. .... .... .... .... .... = Differentiated Services Codepoint: Default (0)
        .... .... ..10 .... .... .... .... .... = Explicit Congestion Notification: ECN-Capable Transport codepoint '10' (2)
    .... .... .... 1010 1111 1010 0101 1110 = Flow Label: 0xafa5e
    Payload Length: 688
    Next Header: TCP (6)
Signed-off-by: Dimitris Michailidis <dmichail@google.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This fixes the following smatch and coccinelle warnings:

  drivers/net/ethernet/cavium/thunder/thunder_xcv.c:119 xcv_setup_link() error: we previously assumed 'xcv' could be null (see line 118) [smatch]
  drivers/net/ethernet/cavium/thunder/thunder_xcv.c:119:16-20: ERROR: xcv is NULL but dereferenced. [coccinelle]

Fixes: 6465859a ("net: thunderx: Add RGMII interface type support")
Signed-off-by: Vincent Stehlé <vincent.stehle@laposte.net>
Cc: Sunil Goutham <sgoutham@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The hwlat tracer creates a kernel thread at start of the tracer. It is
pinned to a single CPU and will move to the next CPU after each period of
running. If the user modifies the migration thread's affinity, it will not
change after that happens.

The original code created the thread at the first instance it was called,
but later was changed to destroy the thread after the tracer was finished,
and would not be created until the next instance of the tracer was
established. The code that initialized the affinity was only called on the
initial instantiation of the tracer. After that, it was not initialized, and
the previous affinity did not match the current newly created one, making
it appear that the user modified the thread's affinity when it did not, and
the thread failed to migrate again.

Cc: stable@vger.kernel.org
Fixes: 0330f7aa ("tracing: Have hwlat trace migrate across tracing_cpumask CPUs")
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>

In case of a zero-length report, the gpio direction_input callback would
currently return success instead of an errno.

Fixes: 1ffb3c40 ("HID: cp2112: make transfer buffers DMA capable")
Cc: stable <stable@vger.kernel.org>     # 4.9
Signed-off-by: Johan Hovold <johan@kernel.org>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>

A recent commit fixing DMA-buffers on stack added a shared transfer
buffer protected by a spinlock. This is broken as the USB HID request
callbacks can sleep. Fix this up by replacing the spinlock with a mutex.

Fixes: 1ffb3c40 ("HID: cp2112: make transfer buffers DMA capable")
Cc: stable <stable@vger.kernel.org>	# 4.9
Signed-off-by: Johan Hovold <johan@kernel.org>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>

These tests are reversed.  A warning should be displayed if an error is
returned, not on success.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>