Merge tag 'sunxi-dt-for-5.1' of...

Merge tag 'sunxi-dt-for-5.1' of git://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux into arm/dt

Allwinner DT changes for 5.1

As usual, this is a random assortment of changes:

  - ARM PMU is enabled on the A10
  - The first usage of the PIO pinbank regulator supplies added,
    for the Bananapi
  - Broadcom-based Bluetooth enabled on the Bananapi M2 Magic and M2
    Ultra, using the serdev bindings
  - Video codec added for the A10
  - Display pipeline for the A23 added and enabled for the generic Q8
    tablets

* tag 'sunxi-dt-for-5.1' of git://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux:
  ARM: dts: sun8i-a23-q8: Set compatible string for LCD panel
  ARM: dts: sun8i-q8-common: Enable display pipeline with RGB LCD panel
  ARM: dts: sun8i-a23: Add compatible strings to display pipeline device nodes
  ARM: dts: sun8i-a33: Move display pipeline nodes to a23/a33 common dtsi
  ARM: dts: sun8i-a23-a33: Move NAND controller device node to sort by address
  ARM: dts: sun4i-a10: Add Video Engine and reserved memory nodes
  ARM: dts: sun4i: Add support for the C1 SRAM region with the SRAM controller
  ARM: dts: sunxi: bananapi-m2-plus: Add Bluetooth device node
  ARM: dts: sun8i: r40: bananapi-m2-ultra: Add Bluetooth device node
  ARM: dts: sun8i: r40: bananapi-m2-ultra: Fix WiFi regulator definitions
  ARM: dts: sun8i: r40: Add pinmux setting for CLK_OUT_A
  ARM: dts: sun8i: r40: Add pinmux settings for UART3 on PG pingroup
  ARM: dts: sun7i: bananapi: Add GPIO banks regulators
  ARM: dts: sun4i-a10: Add PMU node
Signed-off-by: Arnd Bergmann <arnd@arndb.de>

arch/arm/boot/dts/sun4i-a10.dtsi

@@ -184,6 +184,26 @@ de: display-engine {
 		status = "disabled";
 	};
 
+	pmu {
+		compatible = "arm,cortex-a8-pmu";
+		interrupts = <3>;
+	};
+
+	reserved-memory {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges;
+
+		/* Address must be kept in the lower 256 MiBs of DRAM for VE. */
+		default-pool {
+			compatible = "shared-dma-pool";
+			size = <0x6000000>;
+			alloc-ranges = <0x4a000000 0x6000000>;
+			reusable;
+			linux,cma-default;
+		};
+	};
+
 	soc {
 		compatible = "simple-bus";
 		#address-cells = <1>;
@@ -224,6 +244,19 @@ otg_sram: sram-section@0 {
 					status = "disabled";
 				};
 			};
+
+			sram_c: sram@1d00000 {
+				compatible = "mmio-sram";
+				reg = <0x01d00000 0xd0000>;
+				#address-cells = <1>;
+				#size-cells = <1>;
+				ranges = <0 0x01d00000 0xd0000>;
+
+				ve_sram: sram-section@0 {
+					compatible = "allwinner,sun4i-a10-sram-c1";
+					reg = <0x000000 0x80000>;
+				};
+			};
 		};
 
 		dma: dma-controller@1c02000 {
@@ -394,6 +427,17 @@ tcon1_out_hdmi: endpoint@1 {
 			};
 		};
 
+		video-codec@1c0e000 {
+			compatible = "allwinner,sun4i-a10-video-engine";
+			reg = <0x01c0e000 0x1000>;
+			clocks = <&ccu CLK_AHB_VE>, <&ccu CLK_VE>,
+				 <&ccu CLK_DRAM_VE>;
+			clock-names = "ahb", "mod", "ram";
+			resets = <&ccu RST_VE>;
+			interrupts = <53>;
+			allwinner,sram = <&ve_sram 1>;
+		};
+
 		mmc0: mmc@1c0f000 {
 			compatible = "allwinner,sun4i-a10-mmc";
 			reg = <0x01c0f000 0x1000>;

arch/arm/boot/dts/sun7i-a20-bananapi.dts

@@ -191,6 +191,11 @@ &otg_sram {
 };
 
 &pio {
+	vcc-pa-supply = <&reg_vcc3v3>;
+	vcc-pc-supply = <&reg_vcc3v3>;
+	vcc-pe-supply = <&reg_vcc3v3>;
+	vcc-pf-supply = <&reg_vcc3v3>;
+	vcc-pg-supply = <&reg_vcc3v3>;
 	gpio-line-names =
 		/* PA */
 		"ERXD3", "ERXD2", "ERXD1", "ERXD0", "ETXD3",

arch/arm/boot/dts/sun8i-a23-a33.dtsi

@@ -68,6 +68,12 @@ simplefb_lcd: framebuffer-lcd0 {
 		};
 	};
 
+	de: display-engine {
+		/* compatible gets set in SoC specific dtsi file */
+		allwinner,pipelines = <&fe0>;
+		status = "disabled";
+	};
+
 	timer {
 		compatible = "arm,armv7-timer";
 		interrupts = <GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
@@ -155,6 +161,55 @@ dma: dma-controller@1c02000 {
 			#dma-cells = <1>;
 		};
 
+		nfc: nand@1c03000 {
+			compatible = "allwinner,sun4i-a10-nand";
+			reg = <0x01c03000 0x1000>;
+			interrupts = <GIC_SPI 70 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&ccu CLK_BUS_NAND>, <&ccu CLK_NAND>;
+			clock-names = "ahb", "mod";
+			resets = <&ccu RST_BUS_NAND>;
+			reset-names = "ahb";
+			status = "disabled";
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+
+		tcon0: lcd-controller@1c0c000 {
+			/* compatible gets set in SoC specific dtsi file */
+			reg = <0x01c0c000 0x1000>;
+			interrupts = <GIC_SPI 86 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&ccu CLK_BUS_LCD>,
+				 <&ccu CLK_LCD_CH0>;
+			clock-names = "ahb",
+				      "tcon-ch0";
+			clock-output-names = "tcon-pixel-clock";
+			resets = <&ccu RST_BUS_LCD>;
+			reset-names = "lcd";
+			status = "disabled";
+
+			ports {
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				tcon0_in: port@0 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <0>;
+
+					tcon0_in_drc0: endpoint@0 {
+						reg = <0>;
+						remote-endpoint = <&drc0_out_tcon0>;
+					};
+				};
+
+				tcon0_out: port@1 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <1>;
+				};
+			};
+		};
+
 		mmc0: mmc@1c0f000 {
 			compatible = "allwinner,sun7i-a20-mmc";
 			reg = <0x01c0f000 0x1000>;
@@ -214,21 +269,6 @@ mmc2: mmc@1c11000 {
 			#size-cells = <0>;
 		};
 
-		nfc: nand@1c03000 {
-			compatible = "allwinner,sun4i-a10-nand";
-			reg = <0x01c03000 0x1000>;
-			interrupts = <GIC_SPI 70 IRQ_TYPE_LEVEL_HIGH>;
-			clocks = <&ccu CLK_BUS_NAND>, <&ccu CLK_NAND>;
-			clock-names = "ahb", "mod";
-			resets = <&ccu RST_BUS_NAND>;
-			reset-names = "ahb";
-			pinctrl-names = "default";
-			pinctrl-0 = <&nand_pins &nand_pins_cs0 &nand_pins_rb0>;
-			status = "disabled";
-			#address-cells = <1>;
-			#size-cells = <0>;
-		};
-
 		usb_otg: usb@1c19000 {
 			/* compatible gets set in SoC specific dtsi file */
 			reg = <0x01c19000 0x0400>;
@@ -572,6 +612,111 @@ gic: interrupt-controller@1c81000 {
 			interrupts = <GIC_PPI 9 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>;
 		};
 
+		fe0: display-frontend@1e00000 {
+			/* compatible gets set in SoC specific dtsi file */
+			reg = <0x01e00000 0x20000>;
+			interrupts = <GIC_SPI 93 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&ccu CLK_BUS_DE_FE>, <&ccu CLK_DE_FE>,
+				 <&ccu CLK_DRAM_DE_FE>;
+			clock-names = "ahb", "mod",
+				      "ram";
+			resets = <&ccu RST_BUS_DE_FE>;
+
+			ports {
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				fe0_out: port@1 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <1>;
+
+					fe0_out_be0: endpoint@0 {
+						reg = <0>;
+						remote-endpoint = <&be0_in_fe0>;
+					};
+				};
+			};
+		};
+
+		be0: display-backend@1e60000 {
+			/* compatible gets set in SoC specific dtsi file */
+			reg = <0x01e60000 0x10000>;
+			interrupts = <GIC_SPI 95 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&ccu CLK_BUS_DE_BE>, <&ccu CLK_DE_BE>,
+				 <&ccu CLK_DRAM_DE_BE>;
+			clock-names = "ahb", "mod",
+				      "ram";
+			resets = <&ccu RST_BUS_DE_BE>;
+
+			ports {
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				be0_in: port@0 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <0>;
+
+					be0_in_fe0: endpoint@0 {
+						reg = <0>;
+						remote-endpoint = <&fe0_out_be0>;
+					};
+				};
+
+				be0_out: port@1 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <1>;
+
+					be0_out_drc0: endpoint@0 {
+						reg = <0>;
+						remote-endpoint = <&drc0_in_be0>;
+					};
+				};
+			};
+		};
+
+		drc0: drc@1e70000 {
+			/* compatible gets set in SoC specific dtsi file */
+			reg = <0x01e70000 0x10000>;
+			interrupts = <GIC_SPI 91 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&ccu CLK_BUS_DRC>, <&ccu CLK_DRC>,
+				 <&ccu CLK_DRAM_DRC>;
+			clock-names = "ahb", "mod", "ram";
+			resets = <&ccu RST_BUS_DRC>;
+
+			assigned-clocks = <&ccu CLK_DRC>;
+			assigned-clock-rates = <300000000>;
+
+			ports {
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				drc0_in: port@0 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <0>;
+
+					drc0_in_be0: endpoint@0 {
+						reg = <0>;
+						remote-endpoint = <&be0_out_drc0>;
+					};
+				};
+
+				drc0_out: port@1 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <1>;
+
+					drc0_out_tcon0: endpoint@0 {
+						reg = <0>;
+						remote-endpoint = <&tcon0_in_drc0>;
+					};
+				};
+			};
+		};
+
 		rtc: rtc@1f00000 {
 			compatible = "allwinner,sun8i-a23-rtc";
 			reg = <0x01f00000 0x400>;

arch/arm/boot/dts/sun8i-a23-q8-tablet.dts

@@ -61,3 +61,7 @@ &codec {
 		"Headset Mic", "HBIAS";
 	status = "okay";
 };
+
+&panel {
+	compatible = "bananapi,s070wv20-ct16", "simple-panel";
+};

arch/arm/boot/dts/sun8i-a23.dtsi

@@ -62,10 +62,26 @@ codec: codec@1c22c00 {
 	};
 };
 
+&be0 {
+	compatible = "allwinner,sun8i-a23-display-backend";
+};
+
 &ccu {
 	compatible = "allwinner,sun8i-a23-ccu";
 };
 
+&de {
+	compatible = "allwinner,sun8i-a23-display-engine";
+};
+
+&drc0 {
+	compatible = "allwinner,sun8i-a23-drc";
+};
+
+&fe0 {
+	compatible = "allwinner,sun8i-a23-display-frontend";
+};
+
 &pio {
 	compatible = "allwinner,sun8i-a23-pinctrl";
 	interrupts = <GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>,
@@ -73,6 +89,10 @@ &pio {
 		     <GIC_SPI 17 IRQ_TYPE_LEVEL_HIGH>;
 };
 
+&tcon0 {
+	compatible = "allwinner,sun8i-a23-tcon";
+};
+
 &usb_otg {
 	compatible = "allwinner,sun6i-a31-musb";
 };

arch/arm/boot/dts/sun8i-a33.dtsi

@@ -159,12 +159,6 @@ cpu3: cpu@3 {
 		};
 	};
 
-	de: display-engine {
-		compatible = "allwinner,sun8i-a33-display-engine";
-		allwinner,pipelines = <&fe0>;
-		status = "disabled";
-	};
-
 	iio-hwmon {
 		compatible = "iio-hwmon";
 		io-channels = <&ths>;
@@ -209,47 +203,6 @@ link_codec: simple-audio-card,codec {
 	};
 
 	soc {
-		tcon0: lcd-controller@1c0c000 {
-			compatible = "allwinner,sun8i-a33-tcon";
-			reg = <0x01c0c000 0x1000>;
-			interrupts = <GIC_SPI 86 IRQ_TYPE_LEVEL_HIGH>;
-			clocks = <&ccu CLK_BUS_LCD>,
-				 <&ccu CLK_LCD_CH0>;
-			clock-names = "ahb",
-				      "tcon-ch0";
-			clock-output-names = "tcon-pixel-clock";
-			resets = <&ccu RST_BUS_LCD>;
-			reset-names = "lcd";
-			status = "disabled";
-
-			ports {
-				#address-cells = <1>;
-				#size-cells = <0>;
-
-				tcon0_in: port@0 {
-					#address-cells = <1>;
-					#size-cells = <0>;
-					reg = <0>;
-
-					tcon0_in_drc0: endpoint@0 {
-						reg = <0>;
-						remote-endpoint = <&drc0_out_tcon0>;
-					};
-				};
-
-				tcon0_out: port@1 {
-					#address-cells = <1>;
-					#size-cells = <0>;
-					reg = <1>;
-
-					tcon0_out_dsi: endpoint@1 {
-						reg = <1>;
-						remote-endpoint = <&dsi_in_tcon0>;
-					};
-				};
-			};
-		};
-
 		video-codec@1c0e000 {
 			compatible = "allwinner,sun8i-a33-video-engine";
 			reg = <0x01c0e000 0x1000>;
@@ -339,115 +292,6 @@ dphy: d-phy@1ca1000 {
 			status = "disabled";
 			#phy-cells = <0>;
 		};
-
-		fe0: display-frontend@1e00000 {
-			compatible = "allwinner,sun8i-a33-display-frontend";
-			reg = <0x01e00000 0x20000>;
-			interrupts = <GIC_SPI 93 IRQ_TYPE_LEVEL_HIGH>;
-			clocks = <&ccu CLK_BUS_DE_FE>, <&ccu CLK_DE_FE>,
-				 <&ccu CLK_DRAM_DE_FE>;
-			clock-names = "ahb", "mod",
-				      "ram";
-			resets = <&ccu RST_BUS_DE_FE>;
-
-			ports {
-				#address-cells = <1>;
-				#size-cells = <0>;
-
-				fe0_out: port@1 {
-					#address-cells = <1>;
-					#size-cells = <0>;
-					reg = <1>;
-
-					fe0_out_be0: endpoint@0 {
-						reg = <0>;
-						remote-endpoint = <&be0_in_fe0>;
-					};
-				};
-			};
-		};
-
-		be0: display-backend@1e60000 {
-			compatible = "allwinner,sun8i-a33-display-backend";
-			reg = <0x01e60000 0x10000>, <0x01e80000 0x1000>;
-			reg-names = "be", "sat";
-			interrupts = <GIC_SPI 95 IRQ_TYPE_LEVEL_HIGH>;
-			clocks = <&ccu CLK_BUS_DE_BE>, <&ccu CLK_DE_BE>,
-				 <&ccu CLK_DRAM_DE_BE>, <&ccu CLK_BUS_SAT>;
-			clock-names = "ahb", "mod",
-				      "ram", "sat";
-			resets = <&ccu RST_BUS_DE_BE>, <&ccu RST_BUS_SAT>;
-			reset-names = "be", "sat";
-			assigned-clocks = <&ccu CLK_DE_BE>;
-			assigned-clock-rates = <300000000>;
-
-			ports {
-				#address-cells = <1>;
-				#size-cells = <0>;
-
-				be0_in: port@0 {
-					#address-cells = <1>;
-					#size-cells = <0>;
-					reg = <0>;
-
-					be0_in_fe0: endpoint@0 {
-						reg = <0>;
-						remote-endpoint = <&fe0_out_be0>;
-					};
-				};
-
-				be0_out: port@1 {
-					#address-cells = <1>;
-					#size-cells = <0>;
-					reg = <1>;
-
-					be0_out_drc0: endpoint@0 {
-						reg = <0>;
-						remote-endpoint = <&drc0_in_be0>;
-					};
-				};
-			};
-		};
-
-		drc0: drc@1e70000 {
-			compatible = "allwinner,sun8i-a33-drc";
-			reg = <0x01e70000 0x10000>;
-			interrupts = <GIC_SPI 91 IRQ_TYPE_LEVEL_HIGH>;
-			clocks = <&ccu CLK_BUS_DRC>, <&ccu CLK_DRC>,
-				 <&ccu CLK_DRAM_DRC>;
-			clock-names = "ahb", "mod", "ram";
-			resets = <&ccu RST_BUS_DRC>;
-
-			assigned-clocks = <&ccu CLK_DRC>;
-			assigned-clock-rates = <300000000>;
-
-			ports {
-				#address-cells = <1>;
-				#size-cells = <0>;
-
-				drc0_in: port@0 {
-					#address-cells = <1>;
-					#size-cells = <0>;
-					reg = <0>;
-
-					drc0_in_be0: endpoint@0 {
-						reg = <0>;
-						remote-endpoint = <&be0_out_drc0>;
-					};
-				};
-
-				drc0_out: port@1 {
-					#address-cells = <1>;
-					#size-cells = <0>;
-					reg = <1>;
-
-					drc0_out_tcon0: endpoint@0 {
-						reg = <0>;
-						remote-endpoint = <&tcon0_in_drc0>;
-					};
-				};
-			};
-		};
 	};
 
 	thermal-zones {
@@ -524,10 +368,37 @@ cpu_crit: cpu_crit {
 	};
 };
 
+&be0 {
+	compatible = "allwinner,sun8i-a33-display-backend";
+	/* A33 has an extra "SAT" module packed inside the display backend */
+	reg = <0x01e60000 0x10000>, <0x01e80000 0x1000>;
+	reg-names = "be", "sat";
+	clocks = <&ccu CLK_BUS_DE_BE>, <&ccu CLK_DE_BE>,
+		 <&ccu CLK_DRAM_DE_BE>, <&ccu CLK_BUS_SAT>;
+	clock-names = "ahb", "mod",
+		      "ram", "sat";
+	resets = <&ccu RST_BUS_DE_BE>, <&ccu RST_BUS_SAT>;
+	reset-names = "be", "sat";
+	assigned-clocks = <&ccu CLK_DE_BE>;
+	assigned-clock-rates = <300000000>;
+};
+
 &ccu {
 	compatible = "allwinner,sun8i-a33-ccu";
 };
 
+&de {
+	compatible = "allwinner,sun8i-a33-display-engine";
+};
+
+&drc0 {
+	compatible = "allwinner,sun8i-a33-drc";
+};
+
+&fe0 {
+	compatible = "allwinner,sun8i-a33-display-frontend";
+};
+
 &mali {
 	operating-points-v2 = <&mali_opp_table>;
 };
@@ -544,6 +415,17 @@ uart0_pb_pins: uart0-pb-pins {
 
 };
 
+&tcon0 {
+	compatible = "allwinner,sun8i-a33-tcon";
+};
+
+&tcon0_out {
+	tcon0_out_dsi: endpoint@1 {
+		reg = <1>;
+		remote-endpoint = <&dsi_in_tcon0>;
+	};
+};
+
 &usb_otg {
 	compatible = "allwinner,sun8i-a33-musb";
 };

arch/arm/boot/dts/sun8i-q8-common.dtsi

@@ -49,6 +49,26 @@ aliases {
 		ethernet0 = &sdio_wifi;
 	};
 
+	panel: panel {
+		/* Tablet dts should provide panel compatible */
+		backlight = <&backlight>;
+		enable-gpios = <&pio 7 7 GPIO_ACTIVE_HIGH>; /* PH7 */
+		power-supply = <&reg_dc1sw>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		port@0 {
+			reg = <0>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			panel_input: endpoint@0 {
+				reg = <0>;
+				remote-endpoint = <&tcon0_out_lcd>;
+			};
+		};
+	};
+
 	wifi_pwrseq: wifi_pwrseq {
 		compatible = "mmc-pwrseq-simple";
 		/*
@@ -64,6 +84,10 @@ wifi_pwrseq: wifi_pwrseq {
 	};
 };
 
+&de {
+	status = "okay";
+};
+
 &ehci0 {
 	status  = "okay";
 };
@@ -90,6 +114,19 @@ wifi_pwrseq_pin_q8: wifi-pwrseq-pins {
 	};
 };
 
+&tcon0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&lcd_rgb666_pins>;
+	status = "okay";
+};
+
+&tcon0_out {
+	tcon0_out_lcd: endpoint@0 {
+		reg = <0>;
+		remote-endpoint = <&panel_input>;
+	};
+};
+
 &usbphy {
 	usb1_vbus-supply = <&reg_dldo1>;
 };

arch/arm/boot/dts/sun8i-r40-bananapi-m2-ultra.dts

@@ -102,6 +102,8 @@ reg_vcc5v0: vcc5v0 {
 	wifi_pwrseq: wifi_pwrseq {
 		compatible = "mmc-pwrseq-simple";
 		reset-gpios = <&pio 6 10 GPIO_ACTIVE_LOW>; /* PG10 WIFI_EN */
+		clocks = <&ccu CLK_OUTA>;
+		clock-names = "ext_clock";
 	};
 };
 
@@ -196,6 +198,11 @@ &ohci2 {
 	status = "okay";
 };
 
+&pio {
+	pinctrl-names = "default";
+	pinctrl-0 = <&clk_out_a_pin>;
+};
+
 &reg_aldo2 {
 	regulator-always-on;
 	regulator-min-microvolt = <2500000>;
@@ -250,12 +257,27 @@ &reg_dldo1 {
 	regulator-name = "vcc-wifi-io";
 };
 
+/*
+ * Our WiFi chip needs both DLDO2 and DLDO3 to be powered at the same
+ * time, with the two being in sync, to be able to meet maximum power
+ * consumption during transmits. Since this is not really supported
+ * right now, just use the two as always on, and we will fix it later.
+ */
+
 &reg_dldo2 {
+	regulator-always-on;
 	regulator-min-microvolt = <3300000>;
 	regulator-max-microvolt = <3300000>;
 	regulator-name = "vcc-wifi";
 };
 
+&reg_dldo3 {
+	regulator-always-on;
+	regulator-min-microvolt = <3300000>;
+	regulator-max-microvolt = <3300000>;
+	regulator-name = "vcc-wifi-2";
+};
+
 &reg_dldo4 {
 	regulator-min-microvolt = <2500000>;
 	regulator-max-microvolt = <2500000>;
@@ -278,6 +300,25 @@ &uart0 {
 	status = "okay";
 };
 
+&uart3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart3_pg_pins>, <&uart3_rts_cts_pg_pins>;
+	uart-has-rtscts;
+	status = "okay";
+
+	bluetooth {
+		compatible = "brcm,bcm43438-bt";
+		clocks = <&ccu CLK_OUTA>;
+		clock-names = "lpo";
+		vbat-supply = <&reg_dldo2>;
+		vddio-supply = <&reg_dldo1>;
+		device-wakeup-gpios = <&pio 6 11 GPIO_ACTIVE_HIGH>; /* PG11 */
+		/* TODO host wake line connected to PMIC GPIO pins */
+		shutdown-gpios = <&pio 7 12 GPIO_ACTIVE_HIGH>; /* PH12 */
+		max-speed = <1500000>;
+	};
+};
+
 &usbphy {
 	usb1_vbus-supply = <&reg_vcc5v0>;
 	usb2_vbus-supply = <&reg_vcc5v0>;

arch/arm/boot/dts/sun8i-r40.dtsi

@@ -342,6 +342,11 @@ pio: pinctrl@1c20800 {
 			#interrupt-cells = <3>;
 			#gpio-cells = <3>;
 
+			clk_out_a_pin: clk-out-a-pin {
+				pins = "PI12";
+				function = "clk_out_a";
+			};
+
 			gmac_rgmii_pins: gmac-rgmii-pins {
 				pins = "PA0", "PA1", "PA2", "PA3",
 				       "PA4", "PA5", "PA6", "PA7",
@@ -389,6 +394,16 @@ uart0_pb_pins: uart0-pb-pins {
 				pins = "PB22", "PB23";
 				function = "uart0";
 			};
+
+			uart3_pg_pins: uart3-pg-pins {
+				pins = "PG6", "PG7";
+				function = "uart3";
+			};
+
+			uart3_rts_cts_pg_pins: uart3-rts-cts-pg-pins {
+				pins = "PG8", "PG9";
+				function = "uart3";
+			};
 		};
 
 		wdt: watchdog@1c20c90 {

arch/arm/boot/dts/sunxi-bananapi-m2-plus.dtsi

@@ -103,6 +103,8 @@ wifi_pwrseq: wifi_pwrseq {
 		compatible = "mmc-pwrseq-simple";
 		pinctrl-names = "default";
 		reset-gpios = <&r_pio 0 7 GPIO_ACTIVE_LOW>; /* PL7 */
+		clocks = <&rtc 1>;
+		clock-names = "ext_clock";
 	};
 };
 
@@ -215,7 +217,19 @@ &uart0 {
 &uart1 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&uart1_pins>, <&uart1_rts_cts_pins>;
-	status = "okay";
+	uart-has-rtscts;
+	status = "okay";
+
+	bluetooth {
+		compatible = "brcm,bcm43438-bt";
+		clocks = <&rtc 1>;
+		clock-names = "lpo";
+		vbat-supply = <&reg_vcc3v3>;
+		vddio-supply = <&reg_vcc3v3>;
+		device-wakeup-gpios = <&pio 6 13 GPIO_ACTIVE_HIGH>; /* PG13 */
+		host-wakeup-gpios = <&pio 6 11 GPIO_ACTIVE_HIGH>; /* PG11 */
+		shutdown-gpios = <&pio 6 12 GPIO_ACTIVE_HIGH>; /* PG12 */
+	};
 };
 
 &usb_otg {