Merge branch 'devel-stable' into devel

Conflicts:
	arch/arm/kernel/entry-armv.S
	arch/arm/kernel/setup.c
	arch/arm/mm/init.c

arch/arm/Kconfig

@@ -303,6 +303,7 @@ config ARCH_CNS3XXX
 	select CPU_V6
 	select GENERIC_CLOCKEVENTS
 	select ARM_GIC
+	select PCI_DOMAINS if PCI
 	help
 	  Support for Cavium Networks CNS3XXX platform.
 
@@ -469,6 +470,19 @@ config ARCH_LOKI
 	help
 	  Support for the Marvell Loki (88RC8480) SoC.
 
+config ARCH_LPC32XX
+	bool "NXP LPC32XX"
+	select CPU_ARM926T
+	select ARCH_REQUIRE_GPIOLIB
+	select HAVE_IDE
+	select ARM_AMBA
+	select USB_ARCH_HAS_OHCI
+	select COMMON_CLKDEV
+	select GENERIC_TIME
+	select GENERIC_CLOCKEVENTS
+	help
+	  Support for the NXP LPC32XX family of processors
+
 config ARCH_MV78XX0
 	bool "Marvell MV78xx0"
 	select CPU_FEROCEON
@@ -573,6 +587,7 @@ config ARCH_MSM
 	bool "Qualcomm MSM"
 	select HAVE_CLK
 	select GENERIC_CLOCKEVENTS
+	select ARCH_REQUIRE_GPIOLIB
 	help
 	  Support for Qualcomm MSM/QSD based systems.  This runs on the
 	  apps processor of the MSM/QSD and depends on a shared memory
@@ -831,6 +846,8 @@ source "arch/arm/mach-lh7a40x/Kconfig"
 
 source "arch/arm/mach-loki/Kconfig"
 
+source "arch/arm/mach-lpc32xx/Kconfig"
+
 source "arch/arm/mach-msm/Kconfig"
 
 source "arch/arm/mach-mv78xx0/Kconfig"
@@ -1041,7 +1058,7 @@ config ISA_DMA_API
 	bool
 
 config PCI
-	bool "PCI support" if ARCH_INTEGRATOR_AP || ARCH_VERSATILE_PB || ARCH_IXP4XX || ARCH_KS8695 || MACH_ARMCORE
+	bool "PCI support" if ARCH_INTEGRATOR_AP || ARCH_VERSATILE_PB || ARCH_IXP4XX || ARCH_KS8695 || MACH_ARMCORE || ARCH_CNS3XXX
 	help
 	  Find out whether you have a PCI motherboard. PCI is the name of a
 	  bus system, i.e. the way the CPU talks to the other stuff inside
@@ -1372,6 +1389,24 @@ config UACCESS_WITH_MEMCPY
 	  However, if the CPU data cache is using a write-allocate mode,
 	  this option is unlikely to provide any performance gain.
 
+config CC_STACKPROTECTOR
+	bool "Enable -fstack-protector buffer overflow detection (EXPERIMENTAL)"
+	help
+	  This option turns on the -fstack-protector GCC feature. This
+	  feature puts, at the beginning of functions, a canary value on
+	  the stack just before the return address, and validates
+	  the value just before actually returning.  Stack based buffer
+	  overflows (that need to overwrite this return address) now also
+	  overwrite the canary, which gets detected and the attack is then
+	  neutralized via a kernel panic.
+	  This feature requires gcc version 4.2 or above.
+
+config DEPRECATED_PARAM_STRUCT
+	bool "Provide old way to pass kernel parameters"
+	help
+	  This was deprecated in 2001 and announced to live on for 5 years.
+	  Some old boot loaders still use this way.
+
 endmenu
 
 menu "Boot options"
@@ -1482,6 +1517,105 @@ config ATAGS_PROC
 	  Should the atags used to boot the kernel be exported in an "atags"
 	  file in procfs. Useful with kexec.
 
+config AUTO_ZRELADDR
+	bool "Auto calculation of the decompressed kernel image address"
+	depends on !ZBOOT_ROM && !ARCH_U300
+	help
+	  ZRELADDR is the physical address where the decompressed kernel
+	  image will be placed. If AUTO_ZRELADDR is selected, the address
+	  will be determined at run-time by masking the current IP with
+	  0xf8000000. This assumes the zImage being placed in the first 128MB
+	  from start of memory.
+
+config ZRELADDR
+	hex "Physical address of the decompressed kernel image"
+	depends on !AUTO_ZRELADDR
+	default 0x00008000 if ARCH_BCMRING ||\
+		ARCH_CNS3XXX ||\
+		ARCH_DOVE ||\
+		ARCH_EBSA110 ||\
+		ARCH_FOOTBRIDGE ||\
+		ARCH_INTEGRATOR ||\
+		ARCH_IOP13XX ||\
+		ARCH_IOP33X ||\
+		ARCH_IXP2000 ||\
+		ARCH_IXP23XX ||\
+		ARCH_IXP4XX ||\
+		ARCH_KIRKWOOD ||\
+		ARCH_KS8695 ||\
+		ARCH_LOKI ||\
+		ARCH_MMP ||\
+		ARCH_MV78XX0 ||\
+		ARCH_NOMADIK ||\
+		ARCH_NUC93X ||\
+		ARCH_NS9XXX ||\
+		ARCH_ORION5X ||\
+		ARCH_SPEAR3XX ||\
+		ARCH_SPEAR6XX ||\
+		ARCH_U8500 ||\
+		ARCH_VERSATILE ||\
+		ARCH_W90X900
+	default 0x08008000 if ARCH_MX1 ||\
+		ARCH_SHARK
+	default 0x10008000 if ARCH_MSM ||\
+		ARCH_OMAP1 ||\
+		ARCH_RPC
+	default 0x20008000 if ARCH_S5P6440 ||\
+		ARCH_S5P6442 ||\
+		ARCH_S5PC100 ||\
+		ARCH_S5PV210
+	default 0x30008000 if ARCH_S3C2410 ||\
+		ARCH_S3C2400 ||\
+		ARCH_S3C2412 ||\
+		ARCH_S3C2416 ||\
+		ARCH_S3C2440 ||\
+		ARCH_S3C2443
+	default 0x40008000 if ARCH_STMP378X ||\
+		ARCH_STMP37XX ||\
+		ARCH_SH7372 ||\
+		ARCH_SH7377
+	default 0x50008000 if ARCH_S3C64XX ||\
+		ARCH_SH7367
+	default 0x60008000 if ARCH_VEXPRESS
+	default 0x80008000 if ARCH_MX25 ||\
+		ARCH_MX3 ||\
+		ARCH_NETX ||\
+		ARCH_OMAP2PLUS ||\
+		ARCH_PNX4008
+	default 0x90008000 if ARCH_MX5 ||\
+		ARCH_MX91231
+	default 0xa0008000 if ARCH_IOP32X ||\
+		ARCH_PXA ||\
+		MACH_MX27
+	default 0xc0008000 if ARCH_LH7A40X ||\
+		MACH_MX21
+	default 0xf0008000 if ARCH_AAEC2000 ||\
+		ARCH_L7200
+	default 0xc0028000 if ARCH_CLPS711X
+	default 0x70008000 if ARCH_AT91 && (ARCH_AT91CAP9 || ARCH_AT91SAM9G45)
+	default 0x20008000 if ARCH_AT91 && !(ARCH_AT91CAP9 || ARCH_AT91SAM9G45)
+	default 0xc0008000 if ARCH_DAVINCI && ARCH_DAVINCI_DA8XX
+	default 0x80008000 if ARCH_DAVINCI && !ARCH_DAVINCI_DA8XX
+	default 0x00008000 if ARCH_EP93XX && EP93XX_SDCE3_SYNC_PHYS_OFFSET
+	default 0xc0008000 if ARCH_EP93XX && EP93XX_SDCE0_PHYS_OFFSET
+	default 0xd0008000 if ARCH_EP93XX && EP93XX_SDCE1_PHYS_OFFSET
+	default 0xe0008000 if ARCH_EP93XX && EP93XX_SDCE2_PHYS_OFFSET
+	default 0xf0008000 if ARCH_EP93XX && EP93XX_SDCE3_ASYNC_PHYS_OFFSET
+	default 0x00008000 if ARCH_GEMINI && GEMINI_MEM_SWAP
+	default 0x10008000 if ARCH_GEMINI && !GEMINI_MEM_SWAP
+	default 0x70008000 if ARCH_REALVIEW && REALVIEW_HIGH_PHYS_OFFSET
+	default 0x00008000 if ARCH_REALVIEW && !REALVIEW_HIGH_PHYS_OFFSET
+	default 0xc0208000 if ARCH_SA1100 && SA1111
+	default 0xc0008000 if ARCH_SA1100 && !SA1111
+	default 0x30108000 if ARCH_S3C2410 && PM_H1940
+	default 0x28E08000 if ARCH_U300 && MACH_U300_SINGLE_RAM
+	default 0x48008000 if ARCH_U300 && !MACH_U300_SINGLE_RAM
+	help
+	  ZRELADDR is the physical address where the decompressed kernel
+	  image will be placed. ZRELADDR has to be specified when the
+	  assumption of AUTO_ZRELADDR is not valid, or when ZBOOT_ROM is
+	  selected.
+
 endmenu
 
 menu "CPU Power Management"

arch/arm/Makefile

@@ -34,6 +34,10 @@ ifeq ($(CONFIG_FRAME_POINTER),y)
 KBUILD_CFLAGS	+=-fno-omit-frame-pointer -mapcs -mno-sched-prolog
 endif
 
+ifeq ($(CONFIG_CC_STACKPROTECTOR),y)
+KBUILD_CFLAGS	+=-fstack-protector
+endif
+
 ifeq ($(CONFIG_CPU_BIG_ENDIAN),y)
 KBUILD_CPPFLAGS	+= -mbig-endian
 AS		+= -EB
@@ -141,11 +145,12 @@ machine-$(CONFIG_ARCH_KIRKWOOD)		:= kirkwood
 machine-$(CONFIG_ARCH_KS8695)		:= ks8695
 machine-$(CONFIG_ARCH_LH7A40X)		:= lh7a40x
 machine-$(CONFIG_ARCH_LOKI) 		:= loki
+machine-$(CONFIG_ARCH_LPC32XX)		:= lpc32xx
 machine-$(CONFIG_ARCH_MMP)		:= mmp
 machine-$(CONFIG_ARCH_MSM)		:= msm
 machine-$(CONFIG_ARCH_MV78XX0)		:= mv78xx0
-machine-$(CONFIG_ARCH_MX1)		:= mx1
-machine-$(CONFIG_ARCH_MX2)		:= mx2
+machine-$(CONFIG_ARCH_MX1)		:= imx
+machine-$(CONFIG_ARCH_MX2)		:= imx
 machine-$(CONFIG_ARCH_MX25)		:= mx25
 machine-$(CONFIG_ARCH_MX3)		:= mx3
 machine-$(CONFIG_ARCH_MX5)		:= mx5

arch/arm/boot/Makefile

@@ -14,18 +14,16 @@
 MKIMAGE         := $(srctree)/scripts/mkuboot.sh
 
 ifneq ($(MACHINE),)
-include $(srctree)/$(MACHINE)/Makefile.boot
+-include $(srctree)/$(MACHINE)/Makefile.boot
 endif
 
 # Note: the following conditions must always be true:
-#   ZRELADDR == virt_to_phys(PAGE_OFFSET + TEXT_OFFSET)
 #   PARAMS_PHYS must be within 4MB of ZRELADDR
 #   INITRD_PHYS must be in RAM
-ZRELADDR    := $(zreladdr-y)
 PARAMS_PHYS := $(params_phys-y)
 INITRD_PHYS := $(initrd_phys-y)
 
-export ZRELADDR INITRD_PHYS PARAMS_PHYS
+export INITRD_PHYS PARAMS_PHYS
 
 targets := Image zImage xipImage bootpImage uImage
 
@@ -67,7 +65,7 @@ quiet_cmd_uimage = UIMAGE  $@
 ifeq ($(CONFIG_ZBOOT_ROM),y)
 $(obj)/uImage: LOADADDR=$(CONFIG_ZBOOT_ROM_TEXT)
 else
-$(obj)/uImage: LOADADDR=$(ZRELADDR)
+$(obj)/uImage: LOADADDR=$(CONFIG_ZRELADDR)
 endif
 
 ifeq ($(CONFIG_THUMB2_KERNEL),y)

arch/arm/boot/compressed/Makefile

@@ -4,6 +4,7 @@
 # create a compressed vmlinuz image from the original vmlinux
 #
 
+AFLAGS_head.o += -DTEXT_OFFSET=$(TEXT_OFFSET)
 HEAD	= head.o
 OBJS	= misc.o decompress.o
 FONTC	= $(srctree)/drivers/video/console/font_acorn_8x8.c
@@ -75,19 +76,9 @@ endif
 EXTRA_CFLAGS  := -fpic -fno-builtin
 EXTRA_AFLAGS  := -Wa,-march=all
 
-# Supply ZRELADDR, INITRD_PHYS and PARAMS_PHYS to the decompressor via
-# linker symbols.  We only define initrd_phys and params_phys if the
-# machine class defined the corresponding makefile variable.
-LDFLAGS_vmlinux := --defsym zreladdr=$(ZRELADDR)
 ifeq ($(CONFIG_CPU_ENDIAN_BE8),y)
 LDFLAGS_vmlinux += --be8
 endif
-ifneq ($(INITRD_PHYS),)
-LDFLAGS_vmlinux += --defsym initrd_phys=$(INITRD_PHYS)
-endif
-ifneq ($(PARAMS_PHYS),)
-LDFLAGS_vmlinux += --defsym params_phys=$(PARAMS_PHYS)
-endif
 # ?
 LDFLAGS_vmlinux += -p
 # Report unresolved symbol references

arch/arm/boot/compressed/Makefile.debug

-#
-# linux/arch/arm/boot/compressed/Makefile
-#
-# create a compressed vmlinux image from the original vmlinux
-#
-
-COMPRESSED_EXTRA=../../lib/ll_char_wr.o
-OBJECTS=misc-debug.o ll_char_wr.aout.o
-
-CFLAGS=-D__KERNEL__ -O2 -DSTDC_HEADERS -DSTANDALONE_DEBUG -Wall -I../../../../include -c
-
-test-gzip: piggy.aout.o $(OBJECTS)
-	$(CC) -o $@ $(OBJECTS) piggy.aout.o
-
-misc-debug.o: misc.c
-	$(CC) $(CFLAGS) -o $@ misc.c
-
-piggy.aout.o: piggy.o
-	arm-linuxelf-objcopy --change-leading-char -I elf32-arm -O arm-aout32-linux piggy.o piggy.aout.o
-
-ll_char_wr.aout.o: $(COMPRESSED_EXTRA)
-	arm-linuxelf-objcopy --change-leading-char -I elf32-arm -O arm-aout32-linux $(COMPRESSED_EXTRA) ll_char_wr.aout.o
-

arch/arm/boot/compressed/head.S

@@ -170,9 +170,16 @@ not_angel:
 
 		.text
 		adr	r0, LC0
- ARM(		ldmia	r0, {r1, r2, r3, r4, r5, r6, r11, ip, sp})
- THUMB(		ldmia	r0, {r1, r2, r3, r4, r5, r6, r11, ip}	)
+ ARM(		ldmia	r0, {r1, r2, r3, r5, r6, r11, ip, sp})
+ THUMB(		ldmia	r0, {r1, r2, r3, r5, r6, r11, ip}	)
  THUMB(		ldr	sp, [r0, #32]				)
+#ifdef CONFIG_AUTO_ZRELADDR
+		@ determine final kernel image address
+		and	r4, pc, #0xf8000000
+		add	r4, r4, #TEXT_OFFSET
+#else
+		ldr	r4, =CONFIG_ZRELADDR
+#endif
 		subs	r0, r0, r1		@ calculate the delta offset
 
 						@ if delta is zero, we are
@@ -310,18 +317,17 @@ wont_overwrite:	mov	r0, r4
 LC0:		.word	LC0			@ r1
 		.word	__bss_start		@ r2
 		.word	_end			@ r3
-		.word	zreladdr		@ r4
 		.word	_start			@ r5
 		.word	_image_size		@ r6
 		.word	_got_start		@ r11
 		.word	_got_end		@ ip
-		.word	user_stack+4096		@ sp
+		.word	user_stack_end		@ sp
 LC1:		.word	reloc_end - reloc_start
 		.size	LC0, . - LC0
 
 #ifdef CONFIG_ARCH_RPC
 		.globl	params
-params:		ldr	r0, =params_phys
+params:		ldr	r0, =0x10000100		@ params_phys for RPC
 		mov	pc, lr
 		.ltorg
 		.align
@@ -339,9 +345,8 @@ params:		ldr	r0, =params_phys
  *  r4 = kernel execution address
  *  r7 = architecture number
  *  r8 = atags pointer
- *  r9 = run-time address of "start"  (???)
  * On exit,
- *  r1, r2, r3, r9, r10, r12 corrupted
+ *  r0, r1, r2, r3, r9, r10, r12 corrupted
  * This routine must preserve:
  *  r4, r5, r6, r7, r8
  */
@@ -396,12 +401,18 @@ __armv3_mpu_cache_on:
 
 		mov	r0, #0
 		mcr	p15, 0, r0, c7, c0, 0	@ invalidate whole cache v3
+		/*
+		 * ?? ARMv3 MMU does not allow reading the control register,
+		 * does this really work on ARMv3 MPU?
+		 */
 		mrc	p15, 0, r0, c1, c0, 0	@ read control reg
 						@ .... .... .... WC.M
 		orr	r0, r0, #0x000d		@ .... .... .... 11.1
+		/* ?? this overwrites the value constructed above? */
 		mov	r0, #0
 		mcr	p15, 0, r0, c1, c0, 0	@ write control reg
 
+		/* ?? invalidate for the second time? */
 		mcr	p15, 0, r0, c7, c0, 0	@ invalidate whole cache v3
 		mov	pc, lr
 
@@ -771,8 +782,10 @@ proc_types:
  * Turn off the Cache and MMU.  ARMv3 does not support
  * reading the control register, but ARMv4 does.
  *
- * On exit, r0, r1, r2, r3, r9, r12 corrupted
- * This routine must preserve: r4, r6, r7
+ * On exit,
+ *  r0, r1, r2, r3, r9, r12 corrupted
+ * This routine must preserve:
+ *  r4, r6, r7
  */
 		.align	5
 cache_off:	mov	r3, #12			@ cache_off function
@@ -845,7 +858,7 @@ __armv3_mmu_cache_off:
  * Clean and flush the cache to maintain consistency.
  *
  * On exit,
- *  r1, r2, r3, r9, r11, r12 corrupted
+ *  r1, r2, r3, r9, r10, r11, r12 corrupted
  * This routine must preserve:
  *  r0, r4, r5, r6, r7
  */
@@ -988,7 +1001,7 @@ no_cache_id:
 __armv3_mmu_cache_flush:
 __armv3_mpu_cache_flush:
 		mov	r1, #0
-		mcr	p15, 0, r0, c7, c0, 0	@ invalidate whole cache v3
+		mcr	p15, 0, r1, c7, c0, 0	@ invalidate whole cache v3
 		mov	pc, lr
 
 /*
@@ -1001,6 +1014,7 @@ __armv3_mpu_cache_flush:
 phexbuf:	.space	12
 		.size	phexbuf, . - phexbuf
 
+@ phex corrupts {r0, r1, r2, r3}
 phex:		adr	r3, phexbuf
 		mov	r2, #0
 		strb	r2, [r3, r1]
@@ -1015,6 +1029,7 @@ phex:		adr	r3, phexbuf
 		strb	r2, [r3, r1]
 		b	1b
 
+@ puts corrupts {r0, r1, r2, r3}
 puts:		loadsp	r3, r1
 1:		ldrb	r2, [r0], #1
 		teq	r2, #0
@@ -1029,12 +1044,14 @@ puts:		loadsp	r3, r1
 		teq	r0, #0
 		bne	1b
 		mov	pc, lr
+@ putc corrupts {r0, r1, r2, r3}
 putc:
 		mov	r2, r0
 		mov	r0, #0
 		loadsp	r3, r1
 		b	2b
 
+@ memdump corrupts {r0, r1, r2, r3, r10, r11, r12, lr}
 memdump:	mov	r12, r0
 		mov	r10, lr
 		mov	r11, #0
@@ -1070,3 +1087,4 @@ reloc_end:
 		.align
 		.section ".stack", "w"
 user_stack:	.space	4096
+user_stack_end:

arch/arm/boot/compressed/misc.c

@@ -28,9 +28,6 @@ unsigned int __machine_arch_type;
 
 #include <asm/unaligned.h>
 
-#ifdef STANDALONE_DEBUG
-#define putstr printf
-#else
 
 static void putstr(const char *ptr);
 extern void error(char *x);
@@ -116,7 +113,6 @@ static void putstr(const char *ptr)
 	flush();
 }
 
-#endif
 
 void *memcpy(void *__dest, __const void *__src, size_t __n)
 {
@@ -186,7 +182,6 @@ asmlinkage void __div0(void)
 
 extern void do_decompress(u8 *input, int len, u8 *output, void (*error)(char *x));
 
-#ifndef STANDALONE_DEBUG
 
 unsigned long
 decompress_kernel(unsigned long output_start, unsigned long free_mem_ptr_p,
@@ -211,18 +206,3 @@ decompress_kernel(unsigned long output_start, unsigned long free_mem_ptr_p,
 	putstr(" done, booting the kernel.\n");
 	return output_ptr;
 }
-#else
-
-char output_buffer[1500*1024];
-
-int main()
-{
-	output_data = output_buffer;
-
-	putstr("Uncompressing Linux...");
-	decompress(input_data, input_data_end - input_data,
-			NULL, NULL, output_data, NULL, error);
-	putstr("done.\n");
-	return 0;
-}
-#endif

arch/arm/configs/kirkwood_defconfig

@@ -13,11 +13,19 @@ CONFIG_MACH_RD88F6192_NAS=y
 CONFIG_MACH_RD88F6281=y
 CONFIG_MACH_MV88F6281GTW_GE=y
 CONFIG_MACH_SHEEVAPLUG=y
+CONFIG_MACH_ESATA_SHEEVAPLUG=y
+CONFIG_MACH_GURUPLUG=y
 CONFIG_MACH_TS219=y
 CONFIG_MACH_TS41X=y
 CONFIG_MACH_OPENRD_BASE=y
 CONFIG_MACH_OPENRD_CLIENT=y
+CONFIG_MACH_OPENRD_ULTIMATE=y
 CONFIG_MACH_NETSPACE_V2=y
+CONFIG_MACH_INETSPACE_V2=y
+CONFIG_MACH_NETSPACE_MAX_V2=y
+CONFIG_MACH_NET2BIG_V2=y
+CONFIG_MACH_NET5BIG_V2=y
+CONFIG_MACH_T5325=y
 # CONFIG_CPU_FEROCEON_OLD_ID is not set
 CONFIG_NO_HZ=y
 CONFIG_HIGH_RES_TIMERS=y

arch/arm/include/asm/elf.h

@@ -121,4 +121,8 @@ int dump_task_regs(struct task_struct *t, elf_gregset_t *elfregs);
 extern void elf_set_personality(const struct elf32_hdr *);
 #define SET_PERSONALITY(ex)	elf_set_personality(&(ex))
 
+struct mm_struct;
+extern unsigned long arch_randomize_brk(struct mm_struct *mm);
+#define arch_randomize_brk arch_randomize_brk
+
 #endif

arch/arm/include/asm/mach/pci.h

@@ -46,6 +46,7 @@ struct pci_sys_data {
 					/* IRQ mapping				*/
 	int		(*map_irq)(struct pci_dev *, u8, u8);
 	struct hw_pci	*hw;
+	void		*private_data;	/* platform controller private data	*/
 };
 
 /*

arch/arm/include/asm/stackprotector.h

+/*
+ * GCC stack protector support.
+ *
+ * Stack protector works by putting predefined pattern at the start of
+ * the stack frame and verifying that it hasn't been overwritten when
+ * returning from the function.  The pattern is called stack canary
+ * and gcc expects it to be defined by a global variable called
+ * "__stack_chk_guard" on ARM.  This unfortunately means that on SMP
+ * we cannot have a different canary value per task.
+ */
+
+#ifndef _ASM_STACKPROTECTOR_H
+#define _ASM_STACKPROTECTOR_H 1
+
+#include <linux/random.h>
+#include <linux/version.h>
+
+extern unsigned long __stack_chk_guard;
+
+/*
+ * Initialize the stackprotector canary value.
+ *
+ * NOTE: this must only be called from functions that never return,
+ * and it must always be inlined.
+ */
+static __always_inline void boot_init_stack_canary(void)
+{
+	unsigned long canary;
+
+	/* Try to get a semi random initial value. */
+	get_random_bytes(&canary, sizeof(canary));
+	canary ^= LINUX_VERSION_CODE;
+
+	current->stack_canary = canary;
+	__stack_chk_guard = current->stack_canary;
+}
+
+#endif	/* _ASM_STACKPROTECTOR_H */

arch/arm/kernel/Makefile

@@ -13,10 +13,12 @@ CFLAGS_REMOVE_return_address.o = -pg
 
 # Object file lists.
 
-obj-y		:= compat.o elf.o entry-armv.o entry-common.o irq.o \
+obj-y		:= elf.o entry-armv.o entry-common.o irq.o \
 		   process.o ptrace.o return_address.o setup.o signal.o \
 		   sys_arm.o stacktrace.o time.o traps.o
 
+obj-$(CONFIG_DEPRECATED_PARAM_STRUCT) += compat.o
+
 obj-$(CONFIG_LEDS)		+= leds.o
 obj-$(CONFIG_OC_ETM)		+= etm.o
 

arch/arm/kernel/asm-offsets.c

@@ -40,6 +40,9 @@
 int main(void)
 {
   DEFINE(TSK_ACTIVE_MM,		offsetof(struct task_struct, active_mm));
+#ifdef CONFIG_CC_STACKPROTECTOR
+  DEFINE(TSK_STACK_CANARY,	offsetof(struct task_struct, stack_canary));
+#endif
   BLANK();
   DEFINE(TI_FLAGS,		offsetof(struct thread_info, flags));
   DEFINE(TI_PREEMPT,		offsetof(struct thread_info, preempt_count));

arch/arm/kernel/compat.c

@@ -217,10 +217,3 @@ void __init convert_to_tag_list(struct tag *tags)
 	struct param_struct *params = (struct param_struct *)tags;
 	build_tag_list(params, &params->u2);
 }
-
-void __init squash_mem_tags(struct tag *tag)
-{
-	for (; tag->hdr.size; tag = tag_next(tag))
-		if (tag->hdr.tag == ATAG_MEM)
-			tag->hdr.tag = ATAG_NONE;
-}

arch/arm/kernel/compat.h

@@ -9,5 +9,3 @@
 */
 
 extern void convert_to_tag_list(struct tag *tags);
-
-extern void squash_mem_tags(struct tag *tag);

arch/arm/kernel/entry-armv.S

@@ -737,6 +737,11 @@ ENTRY(__switch_to)
 	ldr	r6, [r2, #TI_CPU_DOMAIN]
 #endif
 	set_tls	r3, r4, r5
+#if defined(CONFIG_CC_STACKPROTECTOR) && !defined(CONFIG_SMP)
+	ldr	r7, [r2, #TI_TASK]
+	ldr	r8, =__stack_chk_guard
+	ldr	r7, [r7, #TSK_STACK_CANARY]
+#endif
 #ifdef CONFIG_MMU
 	mcr	p15, 0, r6, c3, c0, 0		@ Set domain register
 #endif
@@ -745,6 +750,9 @@ ENTRY(__switch_to)
 	ldr	r0, =thread_notify_head
 	mov	r1, #THREAD_NOTIFY_SWITCH
 	bl	atomic_notifier_call_chain
+#if defined(CONFIG_CC_STACKPROTECTOR) && !defined(CONFIG_SMP)
+	str	r7, [r8]
+#endif
  THUMB(	mov	ip, r4			   )
 	mov	r0, r5
  ARM(	ldmia	r4, {r4 - sl, fp, sp, pc}  )	@ Load all regs saved previously

arch/arm/kernel/process.c

@@ -28,6 +28,7 @@
 #include <linux/tick.h>
 #include <linux/utsname.h>
 #include <linux/uaccess.h>
+#include <linux/random.h>
 
 #include <asm/cacheflush.h>
 #include <asm/leds.h>
@@ -37,6 +38,12 @@
 #include <asm/stacktrace.h>
 #include <asm/mach/time.h>
 
+#ifdef CONFIG_CC_STACKPROTECTOR
+#include <linux/stackprotector.h>
+unsigned long __stack_chk_guard __read_mostly;
+EXPORT_SYMBOL(__stack_chk_guard);
+#endif
+
 static const char *processor_modes[] = {
   "USER_26", "FIQ_26" , "IRQ_26" , "SVC_26" , "UK4_26" , "UK5_26" , "UK6_26" , "UK7_26" ,
   "UK8_26" , "UK9_26" , "UK10_26", "UK11_26", "UK12_26", "UK13_26", "UK14_26", "UK15_26",
@@ -445,3 +452,9 @@ unsigned long get_wchan(struct task_struct *p)
 	} while (count ++ < 16);
 	return 0;
 }
+
+unsigned long arch_randomize_brk(struct mm_struct *mm)
+{
+	unsigned long range_end = mm->brk + 0x02000000;
+	return randomize_range(mm->brk, range_end, 0) ? : mm->brk;
+}

arch/arm/kernel/setup.c

@@ -47,7 +47,9 @@
 #include <asm/traps.h>
 #include <asm/unwind.h>
 
+#if defined(CONFIG_DEPRECATED_PARAM_STRUCT)
 #include "compat.h"
+#endif
 #include "atags.h"
 #include "tcm.h"
 
@@ -755,6 +757,13 @@ static int __init setup_elfcorehdr(char *arg)
 early_param("elfcorehdr", setup_elfcorehdr);
 #endif /* CONFIG_CRASH_DUMP */
 
+static void __init squash_mem_tags(struct tag *tag)
+{
+	for (; tag->hdr.size; tag = tag_next(tag))
+		if (tag->hdr.tag == ATAG_MEM)
+			tag->hdr.tag = ATAG_NONE;
+}
+
 void __init setup_arch(char **cmdline_p)
 {
 	struct tag *tags = (struct tag *)&init_tags;
@@ -775,12 +784,14 @@ void __init setup_arch(char **cmdline_p)
 	else if (mdesc->boot_params)
 		tags = phys_to_virt(mdesc->boot_params);
 
+#if defined(CONFIG_DEPRECATED_PARAM_STRUCT)
 	/*
 	 * If we have the old style parameters, convert them to
 	 * a tag list.
 	 */
 	if (tags->hdr.tag != ATAG_CORE)
 		convert_to_tag_list(tags);
+#endif
 	if (tags->hdr.tag != ATAG_CORE)
 		tags = (struct tag *)&init_tags;
 

arch/arm/mach-cns3xxx/Makefile

-obj-$(CONFIG_ARCH_CNS3XXX)		+= core.o pm.o
+obj-$(CONFIG_ARCH_CNS3XXX)		+= core.o pm.o devices.o
+obj-$(CONFIG_PCI)			+= pcie.o
 obj-$(CONFIG_MACH_CNS3420VB)		+= cns3420vb.o

arch/arm/mach-cns3xxx/cns3420vb.c

@@ -32,6 +32,7 @@
 #include <mach/cns3xxx.h>
 #include <mach/irqs.h>
 #include "core.h"
+#include "devices.h"
 
 /*
  * NOR Flash
@@ -117,6 +118,9 @@ static void __init cns3420_init(void)
 {
 	platform_add_devices(cns3420_pdevs, ARRAY_SIZE(cns3420_pdevs));
 
+	cns3xxx_ahci_init();
+	cns3xxx_sdhci_init();
+
 	pm_power_off = cns3xxx_power_off;
 }
 

arch/arm/mach-cns3xxx/devices.c

+/*
+ * CNS3xxx common devices
+ *
+ * Copyright 2008 Cavium Networks
+ *		  Scott Shu
+ * Copyright 2010 MontaVista Software, LLC.
+ *		  Anton Vorontsov <avorontsov@mvista.com>
+ *
+ * This file is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License, Version 2, as
+ * published by the Free Software Foundation.
+ */
+
+#include <linux/io.h>
+#include <linux/init.h>
+#include <linux/compiler.h>
+#include <linux/dma-mapping.h>
+#include <linux/platform_device.h>
+#include <mach/cns3xxx.h>
+#include <mach/irqs.h>
+#include "core.h"
+#include "devices.h"
+
+/*
+ * AHCI
+ */
+static struct resource cns3xxx_ahci_resource[] = {
+	[0] = {
+		.start	= CNS3XXX_SATA2_BASE,
+		.end	= CNS3XXX_SATA2_BASE + CNS3XXX_SATA2_SIZE - 1,
+		.flags	= IORESOURCE_MEM,
+	},
+	[1] = {
+		.start	= IRQ_CNS3XXX_SATA,
+		.end	= IRQ_CNS3XXX_SATA,
+		.flags	= IORESOURCE_IRQ,
+	},
+};
+
+static u64 cns3xxx_ahci_dmamask = DMA_BIT_MASK(32);
+
+static struct platform_device cns3xxx_ahci_pdev = {
+	.name		= "ahci",
+	.id		= 0,
+	.resource	= cns3xxx_ahci_resource,
+	.num_resources	= ARRAY_SIZE(cns3xxx_ahci_resource),
+	.dev		= {
+		.dma_mask		= &cns3xxx_ahci_dmamask,
+		.coherent_dma_mask	= DMA_BIT_MASK(32),
+	},
+};
+
+void __init cns3xxx_ahci_init(void)
+{
+	u32 tmp;
+
+	tmp = __raw_readl(MISC_SATA_POWER_MODE);
+	tmp |= 0x1 << 16; /* Disable SATA PHY 0 from SLUMBER Mode */
+	tmp |= 0x1 << 17; /* Disable SATA PHY 1 from SLUMBER Mode */
+	__raw_writel(tmp, MISC_SATA_POWER_MODE);
+
+	/* Enable SATA PHY */
+	cns3xxx_pwr_power_up(0x1 << PM_PLL_HM_PD_CTRL_REG_OFFSET_SATA_PHY0);
+	cns3xxx_pwr_power_up(0x1 << PM_PLL_HM_PD_CTRL_REG_OFFSET_SATA_PHY1);
+
+	/* Enable SATA Clock */
+	cns3xxx_pwr_clk_en(0x1 << PM_CLK_GATE_REG_OFFSET_SATA);
+
+	/* De-Asscer SATA Reset */
+	cns3xxx_pwr_soft_rst(CNS3XXX_PWR_SOFTWARE_RST(SATA));
+
+	platform_device_register(&cns3xxx_ahci_pdev);
+}
+
+/*
+ * SDHCI
+ */
+static struct resource cns3xxx_sdhci_resources[] = {
+	[0] = {
+		.start = CNS3XXX_SDIO_BASE,
+		.end   = CNS3XXX_SDIO_BASE + SZ_4K - 1,
+		.flags = IORESOURCE_MEM,
+	},
+	[1] = {
+		.start = IRQ_CNS3XXX_SDIO,
+		.end   = IRQ_CNS3XXX_SDIO,
+		.flags = IORESOURCE_IRQ,
+	},
+};
+
+static struct platform_device cns3xxx_sdhci_pdev = {
+	.name		= "sdhci-cns3xxx",
+	.id		= 0,
+	.num_resources	= ARRAY_SIZE(cns3xxx_sdhci_resources),
+	.resource	= cns3xxx_sdhci_resources,
+};
+
+void __init cns3xxx_sdhci_init(void)
+{
+	u32 __iomem *gpioa = __io(CNS3XXX_MISC_BASE_VIRT + 0x0014);
+	u32 gpioa_pins = __raw_readl(gpioa);
+
+	/* MMC/SD pins share with GPIOA */
+	gpioa_pins |= 0x1fff0004;
+	__raw_writel(gpioa_pins, gpioa);
+
+	cns3xxx_pwr_clk_en(CNS3XXX_PWR_CLK_EN(SDIO));
+	cns3xxx_pwr_soft_rst(CNS3XXX_PWR_SOFTWARE_RST(SDIO));
+
+	platform_device_register(&cns3xxx_sdhci_pdev);
+}

arch/arm/mach-cns3xxx/devices.h

+/*
+ * CNS3xxx common devices
+ *
+ * Copyright 2008 Cavium Networks
+ *		  Scott Shu
+ * Copyright 2010 MontaVista Software, LLC.
+ *		  Anton Vorontsov <avorontsov@mvista.com>
+ *
+ * This file is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License, Version 2, as
+ * published by the Free Software Foundation.
+ */
+
+#ifndef __CNS3XXX_DEVICES_H_
+#define __CNS3XXX_DEVICES_H_
+
+void __init cns3xxx_ahci_init(void);
+void __init cns3xxx_sdhci_init(void);
+
+#endif /* __CNS3XXX_DEVICES_H_ */

arch/arm/mach-cns3xxx/include/mach/cns3xxx.h

@@ -247,37 +247,36 @@
  * Misc block
  */
 #define MISC_MEM_MAP(offs) (void __iomem *)(CNS3XXX_MISC_BASE_VIRT + (offs))
-#define MISC_MEM_MAP_VALUE(offset) (*((volatile unsigned int *)(CNS3XXX_MISC_BASE_VIRT + (offset))))
-
-#define MISC_MEMORY_REMAP_REG			MISC_MEM_MAP_VALUE(0x00)
-#define MISC_CHIP_CONFIG_REG			MISC_MEM_MAP_VALUE(0x04)
-#define MISC_DEBUG_PROBE_DATA_REG		MISC_MEM_MAP_VALUE(0x08)
-#define MISC_DEBUG_PROBE_SELECTION_REG		MISC_MEM_MAP_VALUE(0x0C)
-#define MISC_IO_PIN_FUNC_SELECTION_REG		MISC_MEM_MAP_VALUE(0x10)
-#define MISC_GPIOA_PIN_ENABLE_REG		MISC_MEM_MAP_VALUE(0x14)
-#define MISC_GPIOB_PIN_ENABLE_REG		MISC_MEM_MAP_VALUE(0x18)
-#define MISC_IO_PAD_DRIVE_STRENGTH_CTRL_A	MISC_MEM_MAP_VALUE(0x1C)
-#define MISC_IO_PAD_DRIVE_STRENGTH_CTRL_B	MISC_MEM_MAP_VALUE(0x20)
-#define MISC_GPIOA_15_0_PULL_CTRL_REG		MISC_MEM_MAP_VALUE(0x24)
-#define MISC_GPIOA_16_31_PULL_CTRL_REG		MISC_MEM_MAP_VALUE(0x28)
-#define MISC_GPIOB_15_0_PULL_CTRL_REG		MISC_MEM_MAP_VALUE(0x2C)
-#define MISC_GPIOB_16_31_PULL_CTRL_REG		MISC_MEM_MAP_VALUE(0x30)
-#define MISC_IO_PULL_CTRL_REG			MISC_MEM_MAP_VALUE(0x34)
-#define MISC_E_FUSE_31_0_REG			MISC_MEM_MAP_VALUE(0x40)
-#define MISC_E_FUSE_63_32_REG			MISC_MEM_MAP_VALUE(0x44)
-#define MISC_E_FUSE_95_64_REG			MISC_MEM_MAP_VALUE(0x48)
-#define MISC_E_FUSE_127_96_REG			MISC_MEM_MAP_VALUE(0x4C)
-#define MISC_SOFTWARE_TEST_1_REG		MISC_MEM_MAP_VALUE(0x50)
-#define MISC_SOFTWARE_TEST_2_REG		MISC_MEM_MAP_VALUE(0x54)
-
-#define MISC_SATA_POWER_MODE			MISC_MEM_MAP_VALUE(0x310)
-
-#define MISC_USB_CFG_REG			MISC_MEM_MAP_VALUE(0x800)
-#define MISC_USB_STS_REG			MISC_MEM_MAP_VALUE(0x804)
-#define MISC_USBPHY00_CFG_REG			MISC_MEM_MAP_VALUE(0x808)
-#define MISC_USBPHY01_CFG_REG			MISC_MEM_MAP_VALUE(0x80c)
-#define MISC_USBPHY10_CFG_REG			MISC_MEM_MAP_VALUE(0x810)
-#define MISC_USBPHY11_CFG_REG			MISC_MEM_MAP_VALUE(0x814)
+
+#define MISC_MEMORY_REMAP_REG			MISC_MEM_MAP(0x00)
+#define MISC_CHIP_CONFIG_REG			MISC_MEM_MAP(0x04)
+#define MISC_DEBUG_PROBE_DATA_REG		MISC_MEM_MAP(0x08)
+#define MISC_DEBUG_PROBE_SELECTION_REG		MISC_MEM_MAP(0x0C)
+#define MISC_IO_PIN_FUNC_SELECTION_REG		MISC_MEM_MAP(0x10)
+#define MISC_GPIOA_PIN_ENABLE_REG		MISC_MEM_MAP(0x14)
+#define MISC_GPIOB_PIN_ENABLE_REG		MISC_MEM_MAP(0x18)
+#define MISC_IO_PAD_DRIVE_STRENGTH_CTRL_A	MISC_MEM_MAP(0x1C)
+#define MISC_IO_PAD_DRIVE_STRENGTH_CTRL_B	MISC_MEM_MAP(0x20)
+#define MISC_GPIOA_15_0_PULL_CTRL_REG		MISC_MEM_MAP(0x24)
+#define MISC_GPIOA_16_31_PULL_CTRL_REG		MISC_MEM_MAP(0x28)
+#define MISC_GPIOB_15_0_PULL_CTRL_REG		MISC_MEM_MAP(0x2C)
+#define MISC_GPIOB_16_31_PULL_CTRL_REG		MISC_MEM_MAP(0x30)
+#define MISC_IO_PULL_CTRL_REG			MISC_MEM_MAP(0x34)
+#define MISC_E_FUSE_31_0_REG			MISC_MEM_MAP(0x40)
+#define MISC_E_FUSE_63_32_REG			MISC_MEM_MAP(0x44)
+#define MISC_E_FUSE_95_64_REG			MISC_MEM_MAP(0x48)
+#define MISC_E_FUSE_127_96_REG			MISC_MEM_MAP(0x4C)
+#define MISC_SOFTWARE_TEST_1_REG		MISC_MEM_MAP(0x50)
+#define MISC_SOFTWARE_TEST_2_REG		MISC_MEM_MAP(0x54)
+
+#define MISC_SATA_POWER_MODE			MISC_MEM_MAP(0x310)
+
+#define MISC_USB_CFG_REG			MISC_MEM_MAP(0x800)
+#define MISC_USB_STS_REG			MISC_MEM_MAP(0x804)
+#define MISC_USBPHY00_CFG_REG			MISC_MEM_MAP(0x808)
+#define MISC_USBPHY01_CFG_REG			MISC_MEM_MAP(0x80c)
+#define MISC_USBPHY10_CFG_REG			MISC_MEM_MAP(0x810)
+#define MISC_USBPHY11_CFG_REG			MISC_MEM_MAP(0x814)
 
 #define MISC_PCIEPHY_CMCTL(x)			MISC_MEM_MAP(0x900 + (x) * 0x004)
 #define MISC_PCIEPHY_CTL(x)			MISC_MEM_MAP(0x940 + (x) * 0x100)
@@ -300,21 +299,21 @@
 /*
  * Power management and clock control
  */
-#define PMU_REG_VALUE(offset) (*((volatile unsigned int *)(CNS3XXX_PM_BASE_VIRT + (offset))))
-
-#define PM_CLK_GATE_REG					PMU_REG_VALUE(0x000)
-#define PM_SOFT_RST_REG					PMU_REG_VALUE(0x004)
-#define PM_HS_CFG_REG					PMU_REG_VALUE(0x008)
-#define PM_CACTIVE_STA_REG				PMU_REG_VALUE(0x00C)
-#define PM_PWR_STA_REG					PMU_REG_VALUE(0x010)
-#define PM_CLK_CTRL_REG					PMU_REG_VALUE(0x014)
-#define PM_PLL_LCD_I2S_CTRL_REG				PMU_REG_VALUE(0x018)
-#define PM_PLL_HM_PD_CTRL_REG				PMU_REG_VALUE(0x01C)
-#define PM_REGULAT_CTRL_REG				PMU_REG_VALUE(0x020)
-#define PM_WDT_CTRL_REG					PMU_REG_VALUE(0x024)
-#define PM_WU_CTRL0_REG					PMU_REG_VALUE(0x028)
-#define PM_WU_CTRL1_REG					PMU_REG_VALUE(0x02C)
-#define PM_CSR_REG					PMU_REG_VALUE(0x030)
+#define PMU_MEM_MAP(offs) (void __iomem *)(CNS3XXX_PM_BASE_VIRT + (offs))
+
+#define PM_CLK_GATE_REG					PMU_MEM_MAP(0x000)
+#define PM_SOFT_RST_REG					PMU_MEM_MAP(0x004)
+#define PM_HS_CFG_REG					PMU_MEM_MAP(0x008)
+#define PM_CACTIVE_STA_REG				PMU_MEM_MAP(0x00C)
+#define PM_PWR_STA_REG					PMU_MEM_MAP(0x010)
+#define PM_CLK_CTRL_REG					PMU_MEM_MAP(0x014)
+#define PM_PLL_LCD_I2S_CTRL_REG				PMU_MEM_MAP(0x018)
+#define PM_PLL_HM_PD_CTRL_REG				PMU_MEM_MAP(0x01C)
+#define PM_REGULAT_CTRL_REG				PMU_MEM_MAP(0x020)
+#define PM_WDT_CTRL_REG					PMU_MEM_MAP(0x024)
+#define PM_WU_CTRL0_REG					PMU_MEM_MAP(0x028)
+#define PM_WU_CTRL1_REG					PMU_MEM_MAP(0x02C)
+#define PM_CSR_REG					PMU_MEM_MAP(0x030)
 
 /* PM_CLK_GATE_REG */
 #define PM_CLK_GATE_REG_OFFSET_SDIO			(25)

arch/arm/mach-cns3xxx/pm.c

@@ -6,18 +6,25 @@
  * published by the Free Software Foundation.
  */
 
+#include <linux/io.h>
 #include <linux/delay.h>
 #include <mach/system.h>
 #include <mach/cns3xxx.h>
 
 void cns3xxx_pwr_clk_en(unsigned int block)
 {
-	PM_CLK_GATE_REG |= (block & PM_CLK_GATE_REG_MASK);
+	u32 reg = __raw_readl(PM_CLK_GATE_REG);
+
+	reg |= (block & PM_CLK_GATE_REG_MASK);
+	__raw_writel(reg, PM_CLK_GATE_REG);
 }
 
 void cns3xxx_pwr_power_up(unsigned int block)
 {
-	PM_PLL_HM_PD_CTRL_REG &= ~(block & CNS3XXX_PWR_PLL_ALL);
+	u32 reg = __raw_readl(PM_PLL_HM_PD_CTRL_REG);
+
+	reg &= ~(block & CNS3XXX_PWR_PLL_ALL);
+	__raw_writel(reg, PM_PLL_HM_PD_CTRL_REG);
 
 	/* Wait for 300us for the PLL output clock locked. */
 	udelay(300);
@@ -25,22 +32,29 @@ void cns3xxx_pwr_power_up(unsigned int block)
 
 void cns3xxx_pwr_power_down(unsigned int block)
 {
+	u32 reg = __raw_readl(PM_PLL_HM_PD_CTRL_REG);
+
 	/* write '1' to power down */
-	PM_PLL_HM_PD_CTRL_REG |= (block & CNS3XXX_PWR_PLL_ALL);
+	reg |= (block & CNS3XXX_PWR_PLL_ALL);
+	__raw_writel(reg, PM_PLL_HM_PD_CTRL_REG);
 };
 
 static void cns3xxx_pwr_soft_rst_force(unsigned int block)
 {
+	u32 reg = __raw_readl(PM_SOFT_RST_REG);
+
 	/*
 	 * bit 0, 28, 29 => program low to reset,
 	 * the other else program low and then high
 	 */
 	if (block & 0x30000001) {
-		PM_SOFT_RST_REG &= ~(block & PM_SOFT_RST_REG_MASK);
+		reg &= ~(block & PM_SOFT_RST_REG_MASK);
 	} else {
-		PM_SOFT_RST_REG &= ~(block & PM_SOFT_RST_REG_MASK);
-		PM_SOFT_RST_REG |= (block & PM_SOFT_RST_REG_MASK);
+		reg &= ~(block & PM_SOFT_RST_REG_MASK);
+		reg |= (block & PM_SOFT_RST_REG_MASK);
 	}
+
+	__raw_writel(reg, PM_SOFT_RST_REG);
 }
 
 void cns3xxx_pwr_soft_rst(unsigned int block)
@@ -73,12 +87,13 @@ void arch_reset(char mode, const char *cmd)
  */
 int cns3xxx_cpu_clock(void)
 {
+	u32 reg = __raw_readl(PM_CLK_CTRL_REG);
 	int cpu;
 	int cpu_sel;
 	int div_sel;
 
-	cpu_sel = (PM_CLK_CTRL_REG >> PM_CLK_CTRL_REG_OFFSET_PLL_CPU_SEL) & 0xf;
-	div_sel = (PM_CLK_CTRL_REG >> PM_CLK_CTRL_REG_OFFSET_CPU_CLK_DIV) & 0x3;
+	cpu_sel = (reg >> PM_CLK_CTRL_REG_OFFSET_PLL_CPU_SEL) & 0xf;
+	div_sel = (reg >> PM_CLK_CTRL_REG_OFFSET_CPU_CLK_DIV) & 0x3;
 
 	cpu = (300 + ((cpu_sel / 3) * 100) + ((cpu_sel % 3) * 33)) >> div_sel;
 

arch/arm/mach-dove/common.c

@@ -752,6 +752,67 @@ void __init dove_xor1_init(void)
 	platform_device_register(&dove_xor11_channel);
 }
 
+/*****************************************************************************
+ * SDIO
+ ****************************************************************************/
+static u64 sdio_dmamask = DMA_BIT_MASK(32);
+
+static struct resource dove_sdio0_resources[] = {
+	{
+		.start	= DOVE_SDIO0_PHYS_BASE,
+		.end	= DOVE_SDIO0_PHYS_BASE + 0xff,
+		.flags	= IORESOURCE_MEM,
+	}, {
+		.start	= IRQ_DOVE_SDIO0,
+		.end	= IRQ_DOVE_SDIO0,
+		.flags	= IORESOURCE_IRQ,
+	},
+};
+
+static struct platform_device dove_sdio0 = {
+	.name		= "sdhci-mv",
+	.id		= 0,
+	.dev		= {
+		.dma_mask		= &sdio_dmamask,
+		.coherent_dma_mask	= DMA_BIT_MASK(32),
+	},
+	.resource	= dove_sdio0_resources,
+	.num_resources	= ARRAY_SIZE(dove_sdio0_resources),
+};
+
+void __init dove_sdio0_init(void)
+{
+	platform_device_register(&dove_sdio0);
+}
+
+static struct resource dove_sdio1_resources[] = {
+	{
+		.start	= DOVE_SDIO1_PHYS_BASE,
+		.end	= DOVE_SDIO1_PHYS_BASE + 0xff,
+		.flags	= IORESOURCE_MEM,
+	}, {
+		.start	= IRQ_DOVE_SDIO1,
+		.end	= IRQ_DOVE_SDIO1,
+		.flags	= IORESOURCE_IRQ,
+	},
+};
+
+static struct platform_device dove_sdio1 = {
+	.name		= "sdhci-mv",
+	.id		= 1,
+	.dev		= {
+		.dma_mask		= &sdio_dmamask,
+		.coherent_dma_mask	= DMA_BIT_MASK(32),
+	},
+	.resource	= dove_sdio1_resources,
+	.num_resources	= ARRAY_SIZE(dove_sdio1_resources),
+};
+
+void __init dove_sdio1_init(void)
+{
+	platform_device_register(&dove_sdio1);
+}
+
 void __init dove_init(void)
 {
 	int tclk;

arch/arm/mach-dove/common.h

@@ -36,5 +36,7 @@ void dove_uart3_init(void);
 void dove_spi0_init(void);
 void dove_spi1_init(void);
 void dove_i2c_init(void);
+void dove_sdio0_init(void);
+void dove_sdio1_init(void);
 
 #endif

arch/arm/mach-dove/dove-db-setup.c

@@ -82,6 +82,8 @@ static void __init dove_db_init(void)
 	dove_ehci0_init();
 	dove_ehci1_init();
 	dove_sata_init(&dove_db_sata_data);
+	dove_sdio0_init();
+	dove_sdio1_init();
 	dove_spi0_init();
 	dove_spi1_init();
 	dove_uart0_init();

arch/arm/mach-mx2/Kconfig → arch/arm/mach-imx/Kconfig

+config IMX_HAVE_DMA_V1
+	bool
+
+if ARCH_MX1
+
+config SOC_IMX1
+	select CPU_ARM920T
+	select IMX_HAVE_DMA_V1
+	select IMX_HAVE_IOMUX_V1
+	bool
+
+comment "MX1 platforms:"
+config MACH_MXLADS
+	bool
+
+config ARCH_MX1ADS
+	bool "MX1ADS platform"
+	select MACH_MXLADS
+	select IMX_HAVE_PLATFORM_IMX_I2C
+	select IMX_HAVE_PLATFORM_IMX_UART
+	help
+	  Say Y here if you are using Motorola MX1ADS/MXLADS boards
+
+config MACH_SCB9328
+	bool "Synertronixx scb9328"
+	select IMX_HAVE_PLATFORM_IMX_UART
+	help
+	  Say Y here if you are using a Synertronixx scb9328 board
+
+endif
+
 if ARCH_MX2
 
+config SOC_IMX21
+	select CPU_ARM926T
+	select ARCH_MXC_AUDMUX_V1
+	select IMX_HAVE_DMA_V1
+	select IMX_HAVE_IOMUX_V1
+	bool
+
+config SOC_IMX27
+	select CPU_ARM926T
+	select ARCH_MXC_AUDMUX_V1
+	select IMX_HAVE_DMA_V1
+	select IMX_HAVE_IOMUX_V1
+	bool
+
 choice
 	prompt "CPUs:"
 	default MACH_MX21
 
 config MACH_MX21
 	bool "i.MX21 support"
-	select ARCH_MXC_AUDMUX_V1
+	select SOC_IMX21
 	help
 	  This enables support for Freescale's MX2 based i.MX21 processor.
 
 config MACH_MX27
 	bool "i.MX27 support"
-	select ARCH_MXC_AUDMUX_V1
+	select SOC_IMX27
 	help
 	  This enables support for Freescale's MX2 based i.MX27 processor.
 
 endchoice
 
-comment "MX2 platforms:"
+endif
+
+if MACH_MX21
+
+comment "MX21 platforms:"
 
 config MACH_MX21ADS
 	bool "MX21ADS platform"
-	depends on MACH_MX21
+	select IMX_HAVE_PLATFORM_IMX_UART
+	select IMX_HAVE_PLATFORM_MXC_NAND
 	help
 	  Include support for MX21ADS platform. This includes specific
 	  configurations for the board and its peripherals.
 
+endif
+
+if MACH_MX27
+
+comment "MX27 platforms:"
+
 config MACH_MX27ADS
 	bool "MX27ADS platform"
-	depends on MACH_MX27
+	select IMX_HAVE_PLATFORM_IMX_I2C
+	select IMX_HAVE_PLATFORM_IMX_UART
+	select IMX_HAVE_PLATFORM_MXC_NAND
 	help
 	  Include support for MX27ADS platform. This includes specific
 	  configurations for the board and its peripherals.
 
 config MACH_PCM038
 	bool "Phytec phyCORE-i.MX27 CPU module (pcm038)"
-	depends on MACH_MX27
+	select IMX_HAVE_PLATFORM_IMX_I2C
+	select IMX_HAVE_PLATFORM_IMX_UART
+	select IMX_HAVE_PLATFORM_MXC_NAND
+	select IMX_HAVE_PLATFORM_SPI_IMX
 	select MXC_ULPI if USB_ULPI
 	help
 	  Include support for phyCORE-i.MX27 (aka pcm038) platform. This
@@ -58,7 +119,9 @@ endchoice
 
 config MACH_CPUIMX27
 	bool "Eukrea CPUIMX27 module"
-	depends on MACH_MX27
+	select IMX_HAVE_PLATFORM_IMX_I2C
+	select IMX_HAVE_PLATFORM_IMX_UART
+	select IMX_HAVE_PLATFORM_MXC_NAND
 	help
 	  Include support for Eukrea CPUIMX27 platform. This includes
 	  specific configurations for the module and its peripherals.
@@ -67,9 +130,16 @@ config MACH_EUKREA_CPUIMX27_USESDHC2
 	bool "CPUIMX27 integrates SDHC2 module"
 	depends on MACH_CPUIMX27
 	help
-	  This adds support for the internal SDHC2 used on CPUIMX27 used
+	  This adds support for the internal SDHC2 used on CPUIMX27
 	  for wifi or eMMC.
 
+config MACH_EUKREA_CPUIMX27_USEUART4
+	bool "CPUIMX27 integrates UART4 module"
+	depends on MACH_CPUIMX27
+	help
+	  This adds support for the internal UART4 used on CPUIMX27
+	  for bluetooth.
+
 choice
 	prompt "Baseboard"
 	depends on MACH_CPUIMX27
@@ -78,6 +148,8 @@ choice
 config MACH_EUKREA_MBIMX27_BASEBOARD
 	prompt "Eukrea MBIMX27 development board"
 	bool
+	select IMX_HAVE_PLATFORM_IMX_UART
+	select IMX_HAVE_PLATFORM_SPI_IMX
 	help
 	  This adds board specific devices that can be found on Eukrea's
 	  MBIMX27 evaluation board.
@@ -86,21 +158,24 @@ endchoice
 
 config MACH_MX27_3DS
 	bool "MX27PDK platform"
-	depends on MACH_MX27
+	select IMX_HAVE_PLATFORM_IMX_UART
 	help
 	  Include support for MX27PDK platform. This includes specific
 	  configurations for the board and its peripherals.
 
 config MACH_IMX27LITE
 	bool "LogicPD MX27 LITEKIT platform"
-	depends on MACH_MX27
+	select IMX_HAVE_PLATFORM_IMX_UART
 	help
 	  Include support for MX27 LITEKIT platform. This includes specific
 	  configurations for the board and its peripherals.
 
 config MACH_PCA100
 	bool "Phytec phyCARD-s (pca100)"
-	depends on MACH_MX27
+	select IMX_HAVE_PLATFORM_IMX_I2C
+	select IMX_HAVE_PLATFORM_IMX_UART
+	select IMX_HAVE_PLATFORM_MXC_NAND
+	select IMX_HAVE_PLATFORM_SPI_IMX
 	select MXC_ULPI if USB_ULPI
 	help
 	  Include support for phyCARD-s (aka pca100) platform. This
@@ -108,7 +183,9 @@ config MACH_PCA100
 
 config MACH_MXT_TD60
 	bool "Maxtrack i-MXT TD60"
-	depends on MACH_MX27
+	select IMX_HAVE_PLATFORM_IMX_I2C
+	select IMX_HAVE_PLATFORM_IMX_UART
+	select IMX_HAVE_PLATFORM_MXC_NAND
 	help
 	  Include support for i-MXT (aka td60) platform. This
 	  includes specific configurations for the module and its peripherals.

arch/arm/mach-mx2/Makefile → arch/arm/mach-imx/Makefile

@@ -4,14 +4,24 @@
 
 # Object file lists.
 
-obj-y	:=  devices.o serial.o
+obj-y	:=  devices.o
 
-obj-$(CONFIG_MACH_MX21) += clock_imx21.o mm-imx21.o
+obj-$(CONFIG_IMX_HAVE_DMA_V1) += dma-v1.o
 
-obj-$(CONFIG_MACH_MX27) += cpu_imx27.o
-obj-$(CONFIG_MACH_MX27) += clock_imx27.o mm-imx27.o
+obj-$(CONFIG_ARCH_MX1) += clock-imx1.o mm-imx1.o
+obj-$(CONFIG_MACH_MX21) += clock-imx21.o mm-imx21.o
+
+obj-$(CONFIG_MACH_MX27) += cpu-imx27.o pm-imx27.o
+obj-$(CONFIG_MACH_MX27) += clock-imx27.o mm-imx27.o
+
+# Support for CMOS sensor interface
+obj-$(CONFIG_MX1_VIDEO)	+= mx1-camera-fiq.o mx1-camera-fiq-ksym.o
+
+obj-$(CONFIG_ARCH_MX1ADS) += mach-mx1ads.o
+obj-$(CONFIG_MACH_SCB9328) += mach-scb9328.o
 
 obj-$(CONFIG_MACH_MX21ADS) += mach-mx21ads.o
+
 obj-$(CONFIG_MACH_MX27ADS) += mach-mx27ads.o
 obj-$(CONFIG_MACH_PCM038) += mach-pcm038.o
 obj-$(CONFIG_MACH_PCM970_BASEBOARD) += pcm970-baseboard.o

arch/arm/mach-mx2/Makefile.boot → arch/arm/mach-imx/Makefile.boot

+zreladdr-$(CONFIG_ARCH_MX1)	:= 0x08008000
+params_phys-$(CONFIG_ARCH_MX1)	:= 0x08000100
+initrd_phys-$(CONFIG_ARCH_MX1)	:= 0x08800000
+
 zreladdr-$(CONFIG_MACH_MX21)	:= 0xC0008000
 params_phys-$(CONFIG_MACH_MX21)	:= 0xC0000100
 initrd_phys-$(CONFIG_MACH_MX21)	:= 0xC0800000

arch/arm/mach-mx1/clock.c → arch/arm/mach-imx/clock-imx1.c

@@ -2,18 +2,17 @@
  *  Copyright (C) 2008 Sascha Hauer <s.hauer@pengutronix.de>, Pengutronix
  *
  * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation; either version 2 of the License, or
- * (at your option) any later version.
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
  *
  * This program is distributed in the hope that it will be useful,
  * but WITHOUT ANY WARRANTY; without even the implied warranty of
  * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
  * GNU General Public License for more details.
  *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA  02111-1307  USA
+ * You should have received a copy of the GNU General Public License along
+ * with this program; if not, write to the Free Software Foundation, Inc.,
+ * 51 Franklin St, Fifth Floor, Boston, MA 02110-1301, USA.
  */
 
 #include <linux/kernel.h>
@@ -29,7 +28,41 @@
 #include <mach/clock.h>
 #include <mach/hardware.h>
 #include <mach/common.h>
-#include "crm_regs.h"
+
+#define IO_ADDR_CCM(off)	(MX1_IO_ADDRESS(MX1_CCM_BASE_ADDR + (off)))
+
+/* CCM register addresses */
+#define CCM_CSCR	IO_ADDR_CCM(0x0)
+#define CCM_MPCTL0	IO_ADDR_CCM(0x4)
+#define CCM_SPCTL0	IO_ADDR_CCM(0xc)
+#define CCM_PCDR	IO_ADDR_CCM(0x20)
+
+#define CCM_CSCR_CLKO_OFFSET	29
+#define CCM_CSCR_CLKO_MASK	(0x7 << 29)
+#define CCM_CSCR_USB_OFFSET	26
+#define CCM_CSCR_USB_MASK	(0x7 << 26)
+#define CCM_CSCR_OSC_EN_SHIFT	17
+#define CCM_CSCR_SYSTEM_SEL	(1 << 16)
+#define CCM_CSCR_BCLK_OFFSET	10
+#define CCM_CSCR_BCLK_MASK	(0xf << 10)
+#define CCM_CSCR_PRESC		(1 << 15)
+
+#define CCM_PCDR_PCLK3_OFFSET	16
+#define CCM_PCDR_PCLK3_MASK	(0x7f << 16)
+#define CCM_PCDR_PCLK2_OFFSET	4
+#define CCM_PCDR_PCLK2_MASK	(0xf << 4)
+#define CCM_PCDR_PCLK1_OFFSET	0
+#define CCM_PCDR_PCLK1_MASK	0xf
+
+#define IO_ADDR_SCM(off)	(MX1_IO_ADDRESS(MX1_SCM_BASE_ADDR + (off)))
+
+/* SCM register addresses */
+#define SCM_GCCR	IO_ADDR_SCM(0xc)
+
+#define SCM_GCCR_DMA_CLK_EN_OFFSET	3
+#define SCM_GCCR_CSI_CLK_EN_OFFSET	2
+#define SCM_GCCR_MMA_CLK_EN_OFFSET	1
+#define SCM_GCCR_USBD_CLK_EN_OFFSET	0
 
 static int _clk_enable(struct clk *clk)
 {
@@ -596,7 +629,8 @@ int __init mx1_clocks_init(unsigned long fref)
 	clk_enable(&hclk);
 	clk_enable(&fclk);
 
-	mxc_timer_init(&gpt_clk, IO_ADDRESS(TIM1_BASE_ADDR), TIM1_INT);
+	mxc_timer_init(&gpt_clk, MX1_IO_ADDRESS(MX1_TIM1_BASE_ADDR),
+			MX1_TIM1_INT);
 
 	return 0;
 }

arch/arm/mach-mx2/clock_imx27.c → arch/arm/mach-imx/clock-imx27.c

@@ -644,7 +644,7 @@ static struct clk_lookup lookups[] = {
 	_REGISTER_CLOCK("spi_imx.1", NULL, cspi2_clk)
 	_REGISTER_CLOCK("spi_imx.2", NULL, cspi3_clk)
 	_REGISTER_CLOCK("imx-fb.0", NULL, lcdc_clk)
-	_REGISTER_CLOCK(NULL, "csi", csi_clk)
+	_REGISTER_CLOCK("mx2-camera.0", NULL, csi_clk)
 	_REGISTER_CLOCK("fsl-usb2-udc", "usb", usb_clk)
 	_REGISTER_CLOCK("fsl-usb2-udc", "usb_ahb", usb_clk1)
 	_REGISTER_CLOCK("mxc-ehci.0", "usb", usb_clk)

arch/arm/mach-imx/devices-imx1.h

+/*
+ * Copyright (C) 2010 Pengutronix
+ * Uwe Kleine-Koenig <u.kleine-koenig@pengutronix.de>
+ *
+ * This program is free software; you can redistribute it and/or modify it under
+ * the terms of the GNU General Public License version 2 as published by the
+ * Free Software Foundation.
+ */
+#include <mach/mx1.h>
+#include <mach/devices-common.h>
+
+#define imx1_add_i2c_imx(pdata)		\
+	imx_add_imx_i2c(0, MX1_I2C_BASE_ADDR, SZ_4K, MX1_INT_I2C, pdata)
+
+#define imx1_add_imx_uart0(pdata)	\
+	imx_add_imx_uart_3irq(0, MX1_UART1_BASE_ADDR, 0xd0, MX1_INT_UART1RX, MX1_INT_UART1TX, MX1_INT_UART1RTS, pdata)
+#define imx1_add_imx_uart1(pdata)	\
+	imx_add_imx_uart_3irq(0, MX1_UART2_BASE_ADDR, 0xd0, MX1_INT_UART2RX, MX1_INT_UART2TX, MX1_INT_UART2RTS, pdata)

arch/arm/mach-imx/devices-imx21.h

+/*
+ * Copyright (C) 2010 Pengutronix
+ * Uwe Kleine-Koenig <u.kleine-koenig@pengutronix.de>
+ *
+ * This program is free software; you can redistribute it and/or modify it under
+ * the terms of the GNU General Public License version 2 as published by the
+ * Free Software Foundation.
+ */
+#include <mach/mx21.h>
+#include <mach/devices-common.h>
+
+#define imx21_add_i2c_imx(pdata)	\
+	imx_add_imx_i2c(0, MX2x_I2C_BASE_ADDR, SZ_4K, MX2x_INT_I2C, pdata)
+
+#define imx21_add_imx_uart0(pdata)	\
+	imx_add_imx_uart_1irq(0, MX21_UART1_BASE_ADDR, SZ_4K, MX21_INT_UART1, pdata)
+#define imx21_add_imx_uart1(pdata)	\
+	imx_add_imx_uart_1irq(1, MX21_UART2_BASE_ADDR, SZ_4K, MX21_INT_UART2, pdata)
+#define imx21_add_imx_uart2(pdata)	\
+	imx_add_imx_uart_1irq(2, MX21_UART3_BASE_ADDR, SZ_4K, MX21_INT_UART3, pdata)
+#define imx21_add_imx_uart3(pdata)	\
+	imx_add_imx_uart_1irq(3, MX21_UART4_BASE_ADDR, SZ_4K, MX21_INT_UART4, pdata)
+
+#define imx21_add_mxc_nand(pdata)	\
+	imx_add_mxc_nand_v1(MX21_NFC_BASE_ADDR, MX21_INT_NANDFC, pdata)
+
+#define imx21_add_spi_imx0(pdata)	\
+	imx_add_spi_imx(0, MX21_CSPI1_BASE_ADDR, SZ_4K, MX21_INT_CSPI1, pdata)
+#define imx21_add_spi_imx1(pdata)	\
+	imx_add_spi_imx(1, MX21_CSPI2_BASE_ADDR, SZ_4K, MX21_INT_CSPI2, pdata)

arch/arm/mach-imx/devices-imx27.h

+/*
+ * Copyright (C) 2010 Pengutronix
+ * Uwe Kleine-Koenig <u.kleine-koenig@pengutronix.de>
+ *
+ * This program is free software; you can redistribute it and/or modify it under
+ * the terms of the GNU General Public License version 2 as published by the
+ * Free Software Foundation.
+ */
+#include <mach/mx27.h>
+#include <mach/devices-common.h>
+
+#define imx27_add_i2c_imx0(pdata)	\
+	imx_add_imx_i2c(0, MX27_I2C1_BASE_ADDR, SZ_4K, MX27_INT_I2C1, pdata)
+#define imx27_add_i2c_imx1(pdata)	\
+	imx_add_imx_i2c(1, MX27_I2C2_BASE_ADDR, SZ_4K, MX27_INT_I2C2, pdata)
+
+#define imx27_add_imx_uart0(pdata)	\
+	imx_add_imx_uart_1irq(0, MX27_UART1_BASE_ADDR, SZ_4K, MX27_INT_UART1, pdata)
+#define imx27_add_imx_uart1(pdata)	\
+	imx_add_imx_uart_1irq(1, MX27_UART2_BASE_ADDR, SZ_4K, MX27_INT_UART2, pdata)
+#define imx27_add_imx_uart2(pdata)	\
+	imx_add_imx_uart_1irq(2, MX27_UART3_BASE_ADDR, SZ_4K, MX27_INT_UART3, pdata)
+#define imx27_add_imx_uart3(pdata)	\
+	imx_add_imx_uart_1irq(3, MX27_UART4_BASE_ADDR, SZ_4K, MX27_INT_UART4, pdata)
+#define imx27_add_imx_uart4(pdata)	\
+	imx_add_imx_uart_1irq(4, MX27_UART5_BASE_ADDR, SZ_4K, MX27_INT_UART5, pdata)
+#define imx27_add_imx_uart5(pdata)	\
+	imx_add_imx_uart_1irq(5, MX27_UART6_BASE_ADDR, SZ_4K, MX27_INT_UART6, pdata)
+
+#define imx27_add_mxc_nand(pdata)	\
+	imx_add_mxc_nand_v1(MX27_NFC_BASE_ADDR, MX27_INT_NANDFC, pdata)
+
+#define imx27_add_spi_imx0(pdata)	\
+	imx_add_spi_imx(0, MX27_CSPI1_BASE_ADDR, SZ_4K, MX27_INT_CSPI1, pdata)
+#define imx27_add_spi_imx1(pdata)	\
+	imx_add_spi_imx(1, MX27_CSPI2_BASE_ADDR, SZ_4K, MX27_INT_CSPI2, pdata)
+#define imx27_add_spi_imx2(pdata)	\
+	imx_add_spi_imx(2, MX27_CSPI3_BASE_ADDR, SZ_4K, MX27_INT_CSPI3, pdata)

arch/arm/mach-mx2/devices.c → arch/arm/mach-imx/devices.c

@@ -11,6 +11,9 @@
  *
  * Copyright 2006-2007 Freescale Semiconductor, Inc. All Rights Reserved.
  * Copyright 2008 Juergen Beisert, kernel@pengutronix.de
+ * Copyright 2008 Sascha Hauer, kernel@pengutronix.de
+ * Copyright (c) 2008 Paulius Zaleckas <paulius.zaleckas@teltonika.lt>
+ * Copyright (c) 2008 Darius Augulis <darius.augulis@teltonika.lt>
  *
  * This program is free software; you can redistribute it and/or
  * modify it under the terms of the GNU General Public License
@@ -32,6 +35,7 @@
 #include <linux/platform_device.h>
 #include <linux/gpio.h>
 #include <linux/dma-mapping.h>
+#include <linux/serial.h>
 
 #include <mach/irqs.h>
 #include <mach/hardware.h>
@@ -40,38 +44,179 @@
 
 #include "devices.h"
 
-/*
- * SPI master controller
- *
- * - i.MX1: 2 channel (slighly different register setting)
- * - i.MX21: 2 channel
- * - i.MX27: 3 channel
- */
-#define DEFINE_IMX_SPI_DEVICE(n, baseaddr, irq)					\
-	static struct resource mxc_spi_resources ## n[] = {			\
-		{								\
-			.start = baseaddr,					\
-			.end = baseaddr + SZ_4K - 1,				\
-			.flags = IORESOURCE_MEM,				\
-		}, {								\
-			.start = irq,						\
-			.end = irq,						\
-			.flags = IORESOURCE_IRQ,				\
-		},								\
-	};									\
-										\
-	struct platform_device mxc_spi_device ## n = {				\
-		.name = "spi_imx",						\
-		.id = n,							\
-		.num_resources = ARRAY_SIZE(mxc_spi_resources ## n),		\
-		.resource = mxc_spi_resources ## n,				\
+#if defined(CONFIG_ARCH_MX1)
+static struct resource imx1_camera_resources[] = {
+	{
+		.start  = 0x00224000,
+		.end    = 0x00224010,
+		.flags  = IORESOURCE_MEM,
+	}, {
+		.start  = MX1_CSI_INT,
+		.end    = MX1_CSI_INT,
+		.flags  = IORESOURCE_IRQ,
+	},
+};
+
+static u64 imx1_camera_dmamask = DMA_BIT_MASK(32);
+
+struct platform_device imx1_camera_device = {
+	.name           = "mx1-camera",
+	.id             = 0, /* This is used to put cameras on this interface */
+	.dev		= {
+		.dma_mask = &imx1_camera_dmamask,
+		.coherent_dma_mask = DMA_BIT_MASK(32),
+	},
+	.resource       = imx1_camera_resources,
+	.num_resources  = ARRAY_SIZE(imx1_camera_resources),
+};
+
+static struct resource imx_rtc_resources[] = {
+	{
+		.start  = 0x00204000,
+		.end    = 0x00204024,
+		.flags  = IORESOURCE_MEM,
+	}, {
+		.start  = MX1_RTC_INT,
+		.end    = MX1_RTC_INT,
+		.flags  = IORESOURCE_IRQ,
+	}, {
+		.start  = MX1_RTC_SAMINT,
+		.end    = MX1_RTC_SAMINT,
+		.flags  = IORESOURCE_IRQ,
+	},
+};
+
+struct platform_device imx_rtc_device = {
+	.name           = "rtc-imx",
+	.id             = 0,
+	.resource       = imx_rtc_resources,
+	.num_resources  = ARRAY_SIZE(imx_rtc_resources),
+};
+
+static struct resource imx_wdt_resources[] = {
+	{
+		.start  = 0x00201000,
+		.end    = 0x00201008,
+		.flags  = IORESOURCE_MEM,
+	}, {
+		.start  = MX1_WDT_INT,
+		.end    = MX1_WDT_INT,
+		.flags  = IORESOURCE_IRQ,
+	},
+};
+
+struct platform_device imx_wdt_device = {
+	.name           = "imx-wdt",
+	.id             = 0,
+	.resource       = imx_wdt_resources,
+	.num_resources  = ARRAY_SIZE(imx_wdt_resources),
+};
+
+static struct resource imx_usb_resources[] = {
+	{
+		.start	= 0x00212000,
+		.end	= 0x00212148,
+		.flags	= IORESOURCE_MEM,
+	}, {
+		.start	= MX1_USBD_INT0,
+		.end	= MX1_USBD_INT0,
+		.flags	= IORESOURCE_IRQ,
+	}, {
+		.start	= MX1_USBD_INT1,
+		.end	= MX1_USBD_INT1,
+		.flags	= IORESOURCE_IRQ,
+	}, {
+		.start	= MX1_USBD_INT2,
+		.end	= MX1_USBD_INT2,
+		.flags	= IORESOURCE_IRQ,
+	}, {
+		.start	= MX1_USBD_INT3,
+		.end	= MX1_USBD_INT3,
+		.flags	= IORESOURCE_IRQ,
+	}, {
+		.start	= MX1_USBD_INT4,
+		.end	= MX1_USBD_INT4,
+		.flags	= IORESOURCE_IRQ,
+	}, {
+		.start	= MX1_USBD_INT5,
+		.end	= MX1_USBD_INT5,
+		.flags	= IORESOURCE_IRQ,
+	}, {
+		.start	= MX1_USBD_INT6,
+		.end	= MX1_USBD_INT6,
+		.flags	= IORESOURCE_IRQ,
+	},
+};
+
+struct platform_device imx_usb_device = {
+	.name		= "imx_udc",
+	.id		= 0,
+	.num_resources	= ARRAY_SIZE(imx_usb_resources),
+	.resource	= imx_usb_resources,
+};
+
+/* GPIO port description */
+static struct mxc_gpio_port imx_gpio_ports[] = {
+	{
+		.chip.label = "gpio-0",
+		.base = (void __iomem *)MX1_IO_ADDRESS(MX1_GPIO_BASE_ADDR),
+		.irq = MX1_GPIO_INT_PORTA,
+		.virtual_irq_start = MXC_GPIO_IRQ_START,
+	}, {
+		.chip.label = "gpio-1",
+		.base = (void __iomem *)MX1_IO_ADDRESS(MX1_GPIO_BASE_ADDR + 0x100),
+		.irq = MX1_GPIO_INT_PORTB,
+		.virtual_irq_start = MXC_GPIO_IRQ_START + 32,
+	}, {
+		.chip.label = "gpio-2",
+		.base = (void __iomem *)MX1_IO_ADDRESS(MX1_GPIO_BASE_ADDR + 0x200),
+		.irq = MX1_GPIO_INT_PORTC,
+		.virtual_irq_start = MXC_GPIO_IRQ_START + 64,
+	}, {
+		.chip.label = "gpio-3",
+		.base = (void __iomem *)MX1_IO_ADDRESS(MX1_GPIO_BASE_ADDR + 0x300),
+		.irq = MX1_GPIO_INT_PORTD,
+		.virtual_irq_start = MXC_GPIO_IRQ_START + 96,
 	}
+};
+
+int __init imx1_register_gpios(void)
+{
+	return mxc_gpio_init(imx_gpio_ports, ARRAY_SIZE(imx_gpio_ports));
+}
+#endif
 
-DEFINE_IMX_SPI_DEVICE(0, MX2x_CSPI1_BASE_ADDR, MX2x_INT_CSPI1);
-DEFINE_IMX_SPI_DEVICE(1, MX2x_CSPI2_BASE_ADDR, MX2x_INT_CSPI2);
+#if defined(CONFIG_MACH_MX21) || defined(CONFIG_MACH_MX27)
 
 #ifdef CONFIG_MACH_MX27
-DEFINE_IMX_SPI_DEVICE(2, MX27_CSPI3_BASE_ADDR, MX27_INT_CSPI3);
+static struct resource mx27_camera_resources[] = {
+	{
+	       .start = MX27_CSI_BASE_ADDR,
+	       .end = MX27_CSI_BASE_ADDR + 0x1f,
+	       .flags = IORESOURCE_MEM,
+	}, {
+	       .start = MX27_EMMA_PRP_BASE_ADDR,
+	       .end = MX27_EMMA_PRP_BASE_ADDR + 0x1f,
+	       .flags = IORESOURCE_MEM,
+	}, {
+	       .start = MX27_INT_CSI,
+	       .end = MX27_INT_CSI,
+	       .flags = IORESOURCE_IRQ,
+	},{
+	       .start = MX27_INT_EMMAPRP,
+	       .end = MX27_INT_EMMAPRP,
+	       .flags = IORESOURCE_IRQ,
+	},
+};
+struct platform_device mx27_camera_device = {
+	.name = "mx2-camera",
+	.id = 0,
+	.num_resources = ARRAY_SIZE(mx27_camera_resources),
+	.resource = mx27_camera_resources,
+	.dev = {
+		.coherent_dma_mask = 0xffffffff,
+	},
+};
 #endif
 
 /*
@@ -140,34 +285,6 @@ struct platform_device mxc_w1_master_device = {
 	.resource = mxc_w1_master_resources,
 };
 
-#define DEFINE_MXC_NAND_DEVICE(pfx, baseaddr, irq)			\
-	static struct resource pfx ## _nand_resources[] = {		\
-		{							\
-			.start = baseaddr,				\
-			.end = baseaddr + SZ_4K - 1,			\
-			.flags = IORESOURCE_MEM,			\
-		}, {							\
-			.start = irq,					\
-			.end = irq,					\
-			.flags = IORESOURCE_IRQ,			\
-		},							\
-	};								\
-									\
-	struct platform_device pfx ## _nand_device = {			\
-		.name = "mxc_nand",					\
-		.id = 0,						\
-		.num_resources = ARRAY_SIZE(pfx ## _nand_resources),	\
-		.resource = pfx ## _nand_resources,			\
-	}
-
-#ifdef CONFIG_MACH_MX21
-DEFINE_MXC_NAND_DEVICE(imx21, MX21_NFC_BASE_ADDR, MX21_INT_NANDFC);
-#endif
-
-#ifdef CONFIG_MACH_MX27
-DEFINE_MXC_NAND_DEVICE(imx27, MX27_NFC_BASE_ADDR, MX27_INT_NANDFC);
-#endif
-
 /*
  * lcdc:
  * - i.MX1: the basic controller
@@ -218,32 +335,6 @@ struct platform_device mxc_fec_device = {
 };
 #endif
 
-#define DEFINE_IMX_I2C_DEVICE(n, baseaddr, irq)				\
-	static struct resource mxc_i2c_resources ## n[] = {		\
-		{							\
-			.start = baseaddr,				\
-			.end = baseaddr + SZ_4K - 1,			\
-			.flags = IORESOURCE_MEM,			\
-		}, {							\
-			.start = irq,					\
-			.end = irq,					\
-			.flags = IORESOURCE_IRQ,			\
-		}							\
-	};								\
-									\
-	struct platform_device mxc_i2c_device ## n = {			\
-		.name = "imx-i2c",					\
-		.id = n,						\
-		.num_resources = ARRAY_SIZE(mxc_i2c_resources ## n),	\
-		.resource = mxc_i2c_resources ## n,			\
-	}
-
-DEFINE_IMX_I2C_DEVICE(0, MX2x_I2C_BASE_ADDR, MX2x_INT_I2C);
-
-#ifdef CONFIG_MACH_MX27
-DEFINE_IMX_I2C_DEVICE(1, MX27_I2C2_BASE_ADDR, MX27_INT_I2C2);
-#endif
-
 static struct resource mxc_pwm_resources[] = {
 	{
 		.start = MX2x_PWM_BASE_ADDR,
@@ -454,26 +545,21 @@ DEFINE_IMX_SSI_DEVICE(1, 2, MX2x_SSI1_BASE_ADDR, MX2x_INT_SSI1);
 
 #ifdef CONFIG_MACH_MX21
 DEFINE_MXC_GPIO_PORTS(MX21, imx21);
+
+int __init imx21_register_gpios(void)
+{
+	return mxc_gpio_init(imx21_gpio_ports, ARRAY_SIZE(imx21_gpio_ports));
+}
 #endif
 
 #ifdef CONFIG_MACH_MX27
 DEFINE_MXC_GPIO_PORTS(MX27, imx27);
-#endif
 
-int __init mxc_register_gpios(void)
+int __init imx27_register_gpios(void)
 {
-#ifdef CONFIG_MACH_MX21
-	if (cpu_is_mx21())
-		return mxc_gpio_init(imx21_gpio_ports, ARRAY_SIZE(imx21_gpio_ports));
-	else
-#endif
-#ifdef CONFIG_MACH_MX27
-	if (cpu_is_mx27())
-		return mxc_gpio_init(imx27_gpio_ports, ARRAY_SIZE(imx27_gpio_ports));
-	else
-#endif
-		return 0;
+	return mxc_gpio_init(imx27_gpio_ports, ARRAY_SIZE(imx27_gpio_ports));
 }
+#endif
 
 #ifdef CONFIG_MACH_MX21
 static struct resource mx21_usbhc_resources[] = {
@@ -501,3 +587,23 @@ struct platform_device mx21_usbhc_device = {
 };
 #endif
 
+static struct resource imx_kpp_resources[] = {
+	{
+		.start  = MX2x_KPP_BASE_ADDR,
+		.end    = MX2x_KPP_BASE_ADDR + 0xf,
+		.flags  = IORESOURCE_MEM
+	}, {
+		.start  = MX2x_INT_KPP,
+		.end    = MX2x_INT_KPP,
+		.flags  = IORESOURCE_IRQ,
+	},
+};
+
+struct platform_device imx_kpp_device = {
+	.name = "imx-keypad",
+	.id = -1,
+	.num_resources = ARRAY_SIZE(imx_kpp_resources),
+	.resource = imx_kpp_resources,
+};
+
+#endif

arch/arm/mach-mx2/devices.h → arch/arm/mach-imx/devices.h

+#ifdef CONFIG_ARCH_MX1
+extern struct platform_device imx1_camera_device;
+extern struct platform_device imx_rtc_device;
+extern struct platform_device imx_wdt_device;
+extern struct platform_device imx_usb_device;
+#endif
+
+#if defined(CONFIG_MACH_MX21) || defined(CONFIG_MACH_MX27)
 extern struct platform_device mxc_gpt1;
 extern struct platform_device mxc_gpt2;
 #ifdef CONFIG_MACH_MX27
@@ -6,37 +14,19 @@ extern struct platform_device mxc_gpt4;
 extern struct platform_device mxc_gpt5;
 #endif
 extern struct platform_device mxc_wdt;
-extern struct platform_device mxc_uart_device0;
-extern struct platform_device mxc_uart_device1;
-extern struct platform_device mxc_uart_device2;
-extern struct platform_device mxc_uart_device3;
-extern struct platform_device mxc_uart_device4;
-extern struct platform_device mxc_uart_device5;
 extern struct platform_device mxc_w1_master_device;
-#ifdef CONFIG_MACH_MX21
-extern struct platform_device imx21_nand_device;
-#endif
-#ifdef CONFIG_MACH_MX27
-extern struct platform_device imx27_nand_device;
-#endif
 extern struct platform_device mxc_fb_device;
 extern struct platform_device mxc_fec_device;
 extern struct platform_device mxc_pwm_device;
-extern struct platform_device mxc_i2c_device0;
-#ifdef CONFIG_MACH_MX27
-extern struct platform_device mxc_i2c_device1;
-#endif
 extern struct platform_device mxc_sdhc_device0;
 extern struct platform_device mxc_sdhc_device1;
 extern struct platform_device mxc_otg_udc_device;
+extern struct platform_device mx27_camera_device;
 extern struct platform_device mxc_otg_host;
 extern struct platform_device mxc_usbh1;
 extern struct platform_device mxc_usbh2;
-extern struct platform_device mxc_spi_device0;
-extern struct platform_device mxc_spi_device1;
-#ifdef CONFIG_MACH_MX27
-extern struct platform_device mxc_spi_device2;
-#endif
 extern struct platform_device mx21_usbhc_device;
 extern struct platform_device imx_ssi_device0;
 extern struct platform_device imx_ssi_device1;
+extern struct platform_device imx_kpp_device;
+#endif

arch/arm/plat-mxc/dma-mx1-mx2.c → arch/arm/mach-imx/dma-v1.c

 /*
- *  linux/arch/arm/plat-mxc/dma-mx1-mx2.c
+ *  linux/arch/arm/plat-mxc/dma-v1.c
  *
  *  i.MX DMA registration and IRQ dispatching
  *
@@ -34,7 +34,7 @@
 #include <asm/system.h>
 #include <asm/irq.h>
 #include <mach/hardware.h>
-#include <mach/dma-mx1-mx2.h>
+#include <mach/dma-v1.h>
 
 #define DMA_DCR     0x00		/* Control Register */
 #define DMA_DISR    0x04		/* Interrupt status Register */

arch/arm/mach-mx2/eukrea_mbimx27-baseboard.c → arch/arm/mach-imx/eukrea_mbimx27-baseboard.c

 /*
- * Copyright (C) 2009 Eric Benard - eric@eukrea.com
+ * Copyright (C) 2009-2010 Eric Benard - eric@eukrea.com
  *
  * Based on pcm970-baseboard.c which is :
  * Copyright (C) 2008 Juergen Beisert (kernel@pengutronix.de)
@@ -24,6 +24,9 @@
 #include <linux/platform_device.h>
 #include <linux/spi/spi.h>
 #include <linux/spi/ads7846.h>
+#include <linux/backlight.h>
+#include <video/platform_lcd.h>
+#include <linux/input/matrix_keypad.h>
 
 #include <asm/mach/arch.h>
 
@@ -32,8 +35,11 @@
 #include <mach/imxfb.h>
 #include <mach/hardware.h>
 #include <mach/mmc.h>
-#include <mach/imx-uart.h>
+#include <mach/spi.h>
+#include <mach/ssi.h>
+#include <mach/audmux.h>
 
+#include "devices-imx27.h"
 #include "devices.h"
 
 static int eukrea_mbimx27_pins[] = {
@@ -48,10 +54,12 @@ static int eukrea_mbimx27_pins[] = {
 	PE10_PF_UART3_CTS,
 	PE11_PF_UART3_RTS,
 	/* UART4 */
+#if !defined(MACH_EUKREA_CPUIMX27_USEUART4)
 	PB26_AF_UART4_RTS,
 	PB28_AF_UART4_TXD,
 	PB29_AF_UART4_CTS,
 	PB31_AF_UART4_RXD,
+#endif
 	/* SDHC1*/
 	PE18_PF_SD1_D0,
 	PE19_PF_SD1_D1,
@@ -84,10 +92,29 @@ static int eukrea_mbimx27_pins[] = {
 	PA30_PF_CONTRAST,
 	PA31_PF_OE_ACD,
 	/* SPI1 */
-	PD28_PF_CSPI1_SS0,
 	PD29_PF_CSPI1_SCLK,
 	PD30_PF_CSPI1_MISO,
 	PD31_PF_CSPI1_MOSI,
+	/* SSI4 */
+#if defined(CONFIG_SND_SOC_EUKREA_TLV320) \
+	|| defined(CONFIG_SND_SOC_EUKREA_TLV320_MODULE)
+	PC16_PF_SSI4_FS,
+	PC17_PF_SSI4_RXD | GPIO_PUEN,
+	PC18_PF_SSI4_TXD | GPIO_PUEN,
+	PC19_PF_SSI4_CLK,
+#endif
+};
+
+static const uint32_t eukrea_mbimx27_keymap[] = {
+	KEY(0, 0, KEY_UP),
+	KEY(0, 1, KEY_DOWN),
+	KEY(1, 0, KEY_RIGHT),
+	KEY(1, 1, KEY_LEFT),
+};
+
+static struct matrix_keymap_data eukrea_mbimx27_keymap_data = {
+	.keymap         = eukrea_mbimx27_keymap,
+	.keymap_size    = ARRAY_SIZE(eukrea_mbimx27_keymap),
 };
 
 static struct gpio_led gpio_leds[] = {
@@ -103,12 +130,6 @@ static struct gpio_led gpio_leds[] = {
 		.active_low		= 1,
 		.gpio			= GPIO_PORTF | 19,
 	},
-	{
-		.name			= "backlight",
-		.default_trigger	= "backlight",
-		.active_low		= 0,
-		.gpio			= GPIO_PORTE | 5,
-	},
 };
 
 static struct gpio_led_platform_data gpio_led_info = {
@@ -127,7 +148,7 @@ static struct platform_device leds_gpio = {
 static struct imx_fb_videomode eukrea_mbimx27_modes[] = {
 	{
 		.mode = {
-			.name		= "CMO-QGVA",
+			.name		= "CMO-QVGA",
 			.refresh	= 60,
 			.xres		= 320,
 			.yres		= 240,
@@ -141,6 +162,38 @@ static struct imx_fb_videomode eukrea_mbimx27_modes[] = {
 		},
 		.pcr		= 0xFAD08B80,
 		.bpp		= 16,
+	}, {
+		.mode = {
+			.name		= "DVI-VGA",
+			.refresh	= 60,
+			.xres		= 640,
+			.yres		= 480,
+			.pixclock	= 32000,
+			.hsync_len	= 1,
+			.left_margin	= 35,
+			.right_margin	= 0,
+			.vsync_len	= 1,
+			.upper_margin	= 7,
+			.lower_margin	= 0,
+		},
+		.pcr		= 0xFA208B80,
+		.bpp		= 16,
+	}, {
+		.mode = {
+			.name		= "DVI-SVGA",
+			.refresh	= 60,
+			.xres		= 800,
+			.yres		= 600,
+			.pixclock	= 25000,
+			.hsync_len	= 1,
+			.left_margin	= 35,
+			.right_margin	= 0,
+			.vsync_len	= 1,
+			.upper_margin	= 7,
+			.lower_margin	= 0,
+		},
+		.pcr		= 0xFA208B80,
+		.bpp		= 16,
 	},
 };
 
@@ -153,16 +206,52 @@ static struct imx_fb_platform_data eukrea_mbimx27_fb_data = {
 	.dmacr		= 0x00040060,
 };
 
-static struct imxuart_platform_data uart_pdata[] = {
-	{
-		.flags = IMXUART_HAVE_RTSCTS,
-	},
-	{
-		.flags = IMXUART_HAVE_RTSCTS,
+static void eukrea_mbimx27_bl_set_intensity(int intensity)
+{
+	if (intensity)
+		gpio_direction_output(GPIO_PORTE | 5, 1);
+	else
+		gpio_direction_output(GPIO_PORTE | 5, 0);
+}
+
+static struct generic_bl_info eukrea_mbimx27_bl_info = {
+	.name			= "eukrea_mbimx27-bl",
+	.max_intensity		= 0xff,
+	.default_intensity	= 0xff,
+	.set_bl_intensity	= eukrea_mbimx27_bl_set_intensity,
+};
+
+static struct platform_device eukrea_mbimx27_bl_dev = {
+	.name			= "generic-bl",
+	.id			= 1,
+	.dev = {
+		.platform_data	= &eukrea_mbimx27_bl_info,
 	},
 };
 
-#if defined(CONFIG_TOUCHSCREEN_ADS7846)
+static void eukrea_mbimx27_lcd_power_set(struct plat_lcd_data *pd,
+				   unsigned int power)
+{
+	if (power)
+		gpio_direction_output(GPIO_PORTA | 25, 1);
+	else
+		gpio_direction_output(GPIO_PORTA | 25, 0);
+}
+
+static struct plat_lcd_data eukrea_mbimx27_lcd_power_data = {
+	.set_power		= eukrea_mbimx27_lcd_power_set,
+};
+
+static struct platform_device eukrea_mbimx27_lcd_powerdev = {
+	.name			= "platform-lcd",
+	.dev.platform_data	= &eukrea_mbimx27_lcd_power_data,
+};
+
+static const struct imxuart_platform_data uart_pdata __initconst = {
+	.flags = IMXUART_HAVE_RTSCTS,
+};
+
+#if defined(CONFIG_TOUCHSCREEN_ADS7846) \
 	|| defined(CONFIG_TOUCHSCREEN_ADS7846_MODULE)
 
 #define ADS7846_PENDOWN (GPIO_PORTD | 25)
@@ -173,7 +262,6 @@ static void ads7846_dev_init(void)
 		printk(KERN_ERR "can't get ads746 pen down GPIO\n");
 		return;
 	}
-
 	gpio_direction_input(ADS7846_PENDOWN);
 }
 
@@ -186,7 +274,9 @@ static struct ads7846_platform_data ads7846_config __initdata = {
 	.get_pendown_state	= ads7846_get_pendown_state,
 	.keep_vref_on		= 1,
 };
+#endif
 
+#if defined(CONFIG_SPI_IMX) || defined(CONFIG_SPI_IMX_MODULE)
 static struct spi_board_info eukrea_mbimx27_spi_board_info[] __initdata = {
 	[0] = {
 		.modalias	= "ads7846",
@@ -201,16 +291,30 @@ static struct spi_board_info eukrea_mbimx27_spi_board_info[] __initdata = {
 
 static int eukrea_mbimx27_spi_cs[] = {GPIO_PORTD | 28};
 
-static struct spi_imx_master eukrea_mbimx27_spi_0_data = {
+static const struct spi_imx_master eukrea_mbimx27_spi0_data __initconst = {
 	.chipselect	= eukrea_mbimx27_spi_cs,
 	.num_chipselect = ARRAY_SIZE(eukrea_mbimx27_spi_cs),
 };
 #endif
 
+static struct i2c_board_info eukrea_mbimx27_i2c_devices[] = {
+	{
+		I2C_BOARD_INFO("tlv320aic23", 0x1a),
+	},
+};
+
 static struct platform_device *platform_devices[] __initdata = {
 	&leds_gpio,
 };
 
+static struct imxmmc_platform_data sdhc_pdata = {
+	.dat3_card_detect = 1,
+};
+
+struct imx_ssi_platform_data eukrea_mbimx27_ssi_pdata = {
+	.flags = IMX_SSI_DMA | IMX_SSI_USE_I2S_SLAVE,
+};
+
 /*
  * system init for baseboard usage. Will be called by cpuimx27 init.
  *
@@ -222,21 +326,52 @@ void __init eukrea_mbimx27_baseboard_init(void)
 	mxc_gpio_setup_multiple_pins(eukrea_mbimx27_pins,
 		ARRAY_SIZE(eukrea_mbimx27_pins), "MBIMX27");
 
-	mxc_register_device(&mxc_uart_device1, &uart_pdata[0]);
-	mxc_register_device(&mxc_uart_device2, &uart_pdata[1]);
+#if defined(CONFIG_SND_SOC_EUKREA_TLV320) \
+	|| defined(CONFIG_SND_SOC_EUKREA_TLV320_MODULE)
+	/* SSI unit master I2S codec connected to SSI_PINS_4*/
+	mxc_audmux_v1_configure_port(MX27_AUDMUX_HPCR1_SSI0,
+			MXC_AUDMUX_V1_PCR_SYN |
+			MXC_AUDMUX_V1_PCR_TFSDIR |
+			MXC_AUDMUX_V1_PCR_TCLKDIR |
+			MXC_AUDMUX_V1_PCR_RFSDIR |
+			MXC_AUDMUX_V1_PCR_RCLKDIR |
+			MXC_AUDMUX_V1_PCR_TFCSEL(MX27_AUDMUX_HPCR3_SSI_PINS_4) |
+			MXC_AUDMUX_V1_PCR_RFCSEL(MX27_AUDMUX_HPCR3_SSI_PINS_4) |
+			MXC_AUDMUX_V1_PCR_RXDSEL(MX27_AUDMUX_HPCR3_SSI_PINS_4)
+	);
+	mxc_audmux_v1_configure_port(MX27_AUDMUX_HPCR3_SSI_PINS_4,
+			MXC_AUDMUX_V1_PCR_SYN |
+			MXC_AUDMUX_V1_PCR_RXDSEL(MX27_AUDMUX_HPCR1_SSI0)
+	);
+#endif
+
+	imx27_add_imx_uart1(&uart_pdata);
+	imx27_add_imx_uart2(&uart_pdata);
+#if !defined(MACH_EUKREA_CPUIMX27_USEUART4)
+	imx27_add_imx_uart3(&uart_pdata);
+#endif
 
 	mxc_register_device(&mxc_fb_device, &eukrea_mbimx27_fb_data);
-	mxc_register_device(&mxc_sdhc_device0, NULL);
+	mxc_register_device(&mxc_sdhc_device0, &sdhc_pdata);
 
-#if defined(CONFIG_TOUCHSCREEN_ADS7846)
+	i2c_register_board_info(0, eukrea_mbimx27_i2c_devices,
+				ARRAY_SIZE(eukrea_mbimx27_i2c_devices));
+
+	mxc_register_device(&imx_ssi_device0, &eukrea_mbimx27_ssi_pdata);
+
+#if defined(CONFIG_TOUCHSCREEN_ADS7846) \
 	|| defined(CONFIG_TOUCHSCREEN_ADS7846_MODULE)
-	/* SPI and ADS7846 Touchscreen controler init */
-	mxc_gpio_mode(GPIO_PORTD | 28 | GPIO_GPIO | GPIO_OUT);
+	/* ADS7846 Touchscreen controller init */
 	mxc_gpio_mode(GPIO_PORTD | 25 | GPIO_GPIO | GPIO_IN);
-	mxc_register_device(&mxc_spi_device0, &eukrea_mbimx27_spi_0_data);
+	ads7846_dev_init();
+#endif
+
+#if defined(CONFIG_SPI_IMX) || defined(CONFIG_SPI_IMX_MODULE)
+	/* SPI_CS0 init */
+	mxc_gpio_mode(GPIO_PORTD | 28 | GPIO_GPIO | GPIO_OUT);
+	imx27_add_spi_imx0(&eukrea_mbimx27_spi0_data);
 	spi_register_board_info(eukrea_mbimx27_spi_board_info,
 			ARRAY_SIZE(eukrea_mbimx27_spi_board_info));
-	ads7846_dev_init();
 #endif
 
 	/* Leds configuration */
@@ -244,6 +379,14 @@ void __init eukrea_mbimx27_baseboard_init(void)
 	mxc_gpio_mode(GPIO_PORTF | 19 | GPIO_GPIO | GPIO_OUT);
 	/* Backlight */
 	mxc_gpio_mode(GPIO_PORTE | 5 | GPIO_GPIO | GPIO_OUT);
+	gpio_request(GPIO_PORTE | 5, "backlight");
+	platform_device_register(&eukrea_mbimx27_bl_dev);
+	/* LCD Reset */
+	mxc_gpio_mode(GPIO_PORTA | 25 | GPIO_GPIO | GPIO_OUT);
+	gpio_request(GPIO_PORTA | 25, "lcd_enable");
+	platform_device_register(&eukrea_mbimx27_lcd_powerdev);
+
+	mxc_register_device(&imx_kpp_device, &eukrea_mbimx27_keymap_data);
 
 	platform_add_devices(platform_devices, ARRAY_SIZE(platform_devices));
 }

arch/arm/mach-imx/include/mach/dma-mx1-mx2.h

+#ifndef __MACH_DMA_MX1_MX2_H__
+#define __MACH_DMA_MX1_MX2_H__
+/*
+ * Don't use this header in new code, it will go away when all users are
+ * converted to mach/dma-v1.h
+ */
+
+#include <mach/dma-v1.h>
+
+#endif /* ifndef __MACH_DMA_MX1_MX2_H__ */

arch/arm/plat-mxc/include/mach/dma-mx1-mx2.h → arch/arm/mach-imx/include/mach/dma-v1.h

 /*
- *  linux/arch/arm/plat-mxc/include/mach/dma-mx1-mx2.h
+ *  linux/arch/arm/mach-imx/include/mach/dma-v1.h
  *
  *  i.MX DMA registration and IRQ dispatching
  *
@@ -22,8 +22,10 @@
  * MA 02110-1301, USA.
  */
 
-#ifndef __ASM_ARCH_MXC_DMA_H
-#define __ASM_ARCH_MXC_DMA_H
+#ifndef __MACH_DMA_V1_H__
+#define __MACH_DMA_V1_H__
+
+#define imx_has_dma_v1()	(cpu_is_mx1() || cpu_is_mx21() || cpu_is_mx27())
 
 #define IMX_DMA_CHANNELS  16
 
@@ -102,4 +104,4 @@ enum imx_dma_prio {
 
 int imx_dma_request_by_prio(const char *name, enum imx_dma_prio prio);
 
-#endif	/* _ASM_ARCH_MXC_DMA_H */
+#endif	/* __MACH_DMA_V1_H__ */

arch/arm/mach-mx2/mach-cpuimx27.c → arch/arm/mach-imx/mach-cpuimx27.c

@@ -26,20 +26,24 @@
 #include <linux/mtd/physmap.h>
 #include <linux/platform_device.h>
 #include <linux/serial_8250.h>
+#include <linux/usb/otg.h>
+#include <linux/usb/ulpi.h>
+#include <linux/fsl_devices.h>
 
 #include <asm/mach-types.h>
 #include <asm/mach/arch.h>
 #include <asm/mach/time.h>
 #include <asm/mach/map.h>
 
-#include <mach/board-eukrea_cpuimx27.h>
+#include <mach/eukrea-baseboards.h>
 #include <mach/common.h>
 #include <mach/hardware.h>
-#include <mach/i2c.h>
 #include <mach/iomux-mx27.h>
-#include <mach/imx-uart.h>
 #include <mach/mxc_nand.h>
+#include <mach/mxc_ehci.h>
+#include <mach/ulpi.h>
 
+#include "devices-imx27.h"
 #include "devices.h"
 
 static int eukrea_cpuimx27_pins[] = {
@@ -49,10 +53,12 @@ static int eukrea_cpuimx27_pins[] = {
 	PE14_PF_UART1_CTS,
 	PE15_PF_UART1_RTS,
 	/* UART4 */
+#if defined(MACH_EUKREA_CPUIMX27_USEUART4)
 	PB26_AF_UART4_RTS,
 	PB28_AF_UART4_TXD,
 	PB29_AF_UART4_CTS,
 	PB31_AF_UART4_RXD,
+#endif
 	/* FEC */
 	PD0_AIN_FEC_TXD0,
 	PD1_AIN_FEC_TXD1,
@@ -76,19 +82,47 @@ static int eukrea_cpuimx27_pins[] = {
 	PD17_PF_I2C_DATA,
 	PD18_PF_I2C_CLK,
 	/* SDHC2 */
+#if defined(CONFIG_MACH_EUKREA_CPUIMX27_USESDHC2)
 	PB4_PF_SD2_D0,
 	PB5_PF_SD2_D1,
 	PB6_PF_SD2_D2,
 	PB7_PF_SD2_D3,
 	PB8_PF_SD2_CMD,
 	PB9_PF_SD2_CLK,
+#endif
 #if defined(CONFIG_SERIAL_8250) || defined(CONFIG_SERIAL_8250_MODULE)
 	/* Quad UART's IRQ */
-	GPIO_PORTD | 22 | GPIO_GPIO | GPIO_IN,
-	GPIO_PORTD | 23 | GPIO_GPIO | GPIO_IN,
-	GPIO_PORTD | 27 | GPIO_GPIO | GPIO_IN,
-	GPIO_PORTD | 30 | GPIO_GPIO | GPIO_IN,
+	GPIO_PORTB | 22 | GPIO_GPIO | GPIO_IN,
+	GPIO_PORTB | 23 | GPIO_GPIO | GPIO_IN,
+	GPIO_PORTB | 27 | GPIO_GPIO | GPIO_IN,
+	GPIO_PORTB | 30 | GPIO_GPIO | GPIO_IN,
 #endif
+	/* OTG */
+	PC7_PF_USBOTG_DATA5,
+	PC8_PF_USBOTG_DATA6,
+	PC9_PF_USBOTG_DATA0,
+	PC10_PF_USBOTG_DATA2,
+	PC11_PF_USBOTG_DATA1,
+	PC12_PF_USBOTG_DATA4,
+	PC13_PF_USBOTG_DATA3,
+	PE0_PF_USBOTG_NXT,
+	PE1_PF_USBOTG_STP,
+	PE2_PF_USBOTG_DIR,
+	PE24_PF_USBOTG_CLK,
+	PE25_PF_USBOTG_DATA7,
+	/* USBH2 */
+	PA0_PF_USBH2_CLK,
+	PA1_PF_USBH2_DIR,
+	PA2_PF_USBH2_DATA7,
+	PA3_PF_USBH2_NXT,
+	PA4_PF_USBH2_STP,
+	PD19_AF_USBH2_DATA4,
+	PD20_AF_USBH2_DATA3,
+	PD21_AF_USBH2_DATA6,
+	PD22_AF_USBH2_DATA0,
+	PD23_AF_USBH2_DATA2,
+	PD24_AF_USBH2_DATA1,
+	PD26_AF_USBH2_DATA5,
 };
 
 static struct physmap_flash_data eukrea_cpuimx27_flash_data = {
@@ -111,15 +145,12 @@ static struct platform_device eukrea_cpuimx27_nor_mtd_device = {
 	.resource = &eukrea_cpuimx27_flash_resource,
 };
 
-static struct imxuart_platform_data uart_pdata[] = {
-	{
-		.flags = IMXUART_HAVE_RTSCTS,
-	}, {
-		.flags = IMXUART_HAVE_RTSCTS,
-	},
+static const struct imxuart_platform_data uart_pdata __initconst = {
+	.flags = IMXUART_HAVE_RTSCTS,
 };
 
-static struct mxc_nand_platform_data eukrea_cpuimx27_nand_board_info = {
+static const struct mxc_nand_platform_data
+cpuimx27_nand_board_info __initconst = {
 	.width = 1,
 	.hw_ecc = 1,
 };
@@ -127,9 +158,11 @@ static struct mxc_nand_platform_data eukrea_cpuimx27_nand_board_info = {
 static struct platform_device *platform_devices[] __initdata = {
 	&eukrea_cpuimx27_nor_mtd_device,
 	&mxc_fec_device,
+	&mxc_wdt,
+	&mxc_w1_master_device,
 };
 
-static struct imxi2c_platform_data eukrea_cpuimx27_i2c_1_data = {
+static const struct imxi2c_platform_data cpuimx27_i2c1_data __initconst = {
 	.bitrate = 100000,
 };
 
@@ -182,34 +215,83 @@ static struct platform_device serial_device = {
 };
 #endif
 
+#if defined(CONFIG_USB_ULPI)
+static struct mxc_usbh_platform_data otg_pdata = {
+	.portsc	= MXC_EHCI_MODE_ULPI,
+	.flags	= MXC_EHCI_INTERFACE_DIFF_UNI,
+};
+
+static struct mxc_usbh_platform_data usbh2_pdata = {
+	.portsc	= MXC_EHCI_MODE_ULPI,
+	.flags	= MXC_EHCI_INTERFACE_DIFF_UNI,
+};
+#endif
+
+static struct fsl_usb2_platform_data otg_device_pdata = {
+	.operating_mode = FSL_USB2_DR_DEVICE,
+	.phy_mode       = FSL_USB2_PHY_ULPI,
+};
+
+static int otg_mode_host;
+
+static int __init eukrea_cpuimx27_otg_mode(char *options)
+{
+	if (!strcmp(options, "host"))
+		otg_mode_host = 1;
+	else if (!strcmp(options, "device"))
+		otg_mode_host = 0;
+	else
+		pr_info("otg_mode neither \"host\" nor \"device\". "
+			"Defaulting to device\n");
+	return 0;
+}
+__setup("otg_mode=", eukrea_cpuimx27_otg_mode);
+
 static void __init eukrea_cpuimx27_init(void)
 {
 	mxc_gpio_setup_multiple_pins(eukrea_cpuimx27_pins,
 		ARRAY_SIZE(eukrea_cpuimx27_pins), "CPUIMX27");
 
-	mxc_register_device(&mxc_uart_device0, &uart_pdata[0]);
+	imx27_add_imx_uart0(&uart_pdata);
 
-	mxc_register_device(&imx27_nand_device,
-			&eukrea_cpuimx27_nand_board_info);
+	imx27_add_mxc_nand(&cpuimx27_nand_board_info);
 
 	i2c_register_board_info(0, eukrea_cpuimx27_i2c_devices,
 				ARRAY_SIZE(eukrea_cpuimx27_i2c_devices));
 
-	mxc_register_device(&mxc_i2c_device0, &eukrea_cpuimx27_i2c_1_data);
+	imx27_add_i2c_imx1(&cpuimx27_i2c1_data);
 
 	platform_add_devices(platform_devices, ARRAY_SIZE(platform_devices));
 
 #if defined(CONFIG_MACH_EUKREA_CPUIMX27_USESDHC2)
 	/* SDHC2 can be used for Wifi */
 	mxc_register_device(&mxc_sdhc_device1, NULL);
+#endif
+#if defined(MACH_EUKREA_CPUIMX27_USEUART4)
 	/* in which case UART4 is also used for Bluetooth */
-	mxc_register_device(&mxc_uart_device3, &uart_pdata[1]);
+	imx27_add_imx_uart3(&uart_pdata);
 #endif
 
 #if defined(CONFIG_SERIAL_8250) || defined(CONFIG_SERIAL_8250_MODULE)
 	platform_device_register(&serial_device);
 #endif
 
+#if defined(CONFIG_USB_ULPI)
+	if (otg_mode_host) {
+		otg_pdata.otg = otg_ulpi_create(&mxc_ulpi_access_ops,
+				USB_OTG_DRV_VBUS | USB_OTG_DRV_VBUS_EXT);
+
+		mxc_register_device(&mxc_otg_host, &otg_pdata);
+	}
+
+	usbh2_pdata.otg = otg_ulpi_create(&mxc_ulpi_access_ops,
+				USB_OTG_DRV_VBUS | USB_OTG_DRV_VBUS_EXT);
+
+	mxc_register_device(&mxc_usbh2, &usbh2_pdata);
+#endif
+	if (!otg_mode_host)
+		mxc_register_device(&mxc_otg_udc_device, &otg_device_pdata);
+
 #ifdef CONFIG_MACH_EUKREA_MBIMX27_BASEBOARD
 	eukrea_mbimx27_baseboard_init();
 #endif

arch/arm/mach-mx2/mach-imx27lite.c → arch/arm/mach-imx/mach-imx27lite.c

@@ -12,10 +12,6 @@
  * but WITHOUT ANY WARRANTY; without even the implied warranty of
  * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
  * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA  02111-1307  USA
  */
 
 #include <linux/platform_device.h>
@@ -26,10 +22,9 @@
 #include <asm/mach/map.h>
 #include <mach/hardware.h>
 #include <mach/common.h>
-#include <mach/imx-uart.h>
 #include <mach/iomux-mx27.h>
-#include <mach/board-mx27lite.h>
 
+#include "devices-imx27.h"
 #include "devices.h"
 
 static unsigned int mx27lite_pins[] = {
@@ -59,7 +54,7 @@ static unsigned int mx27lite_pins[] = {
 	PF23_AIN_FEC_TX_EN,
 };
 
-static struct imxuart_platform_data uart_pdata = {
+static const struct imxuart_platform_data uart_pdata __initconst = {
 	.flags = IMXUART_HAVE_RTSCTS,
 };
 
@@ -71,7 +66,7 @@ static void __init mx27lite_init(void)
 {
 	mxc_gpio_setup_multiple_pins(mx27lite_pins, ARRAY_SIZE(mx27lite_pins),
 		"imx27lite");
-	mxc_register_device(&mxc_uart_device0, &uart_pdata);
+	imx27_add_imx_uart0(&uart_pdata);
 	platform_add_devices(platform_devices, ARRAY_SIZE(platform_devices));
 }
 

arch/arm/mach-mx1/mach-mx1ads.c → arch/arm/mach-imx/mach-mx1ads.c

@@ -26,10 +26,10 @@
 #include <mach/common.h>
 #include <mach/hardware.h>
 #include <mach/i2c.h>
-#include <mach/imx-uart.h>
 #include <mach/iomux-mx1.h>
 #include <mach/irqs.h>
 
+#include "devices-imx1.h"
 #include "devices.h"
 
 static int mx1ads_pins[] = {
@@ -58,12 +58,12 @@ static int mx1ads_pins[] = {
  * UARTs platform data
  */
 
-static struct imxuart_platform_data uart_pdata[] = {
-	{
-		.flags = IMXUART_HAVE_RTSCTS,
-	}, {
-		.flags = IMXUART_HAVE_RTSCTS,
-	},
+static const struct imxuart_platform_data uart0_pdata __initconst = {
+	.flags = IMXUART_HAVE_RTSCTS,
+};
+       
+static const struct imxuart_platform_data uart1_pdata __initconst = {
+	.flags = IMXUART_HAVE_RTSCTS,
 };
 
 /*
@@ -75,8 +75,8 @@ static struct physmap_flash_data mx1ads_flash_data = {
 };
 
 static struct resource flash_resource = {
-	.start	= IMX_CS0_PHYS,
-	.end	= IMX_CS0_PHYS + SZ_32M - 1,
+	.start	= MX1_CS0_PHYS,
+	.end	= MX1_CS0_PHYS + SZ_32M - 1,
 	.flags	= IORESOURCE_MEM,
 };
 
@@ -98,7 +98,7 @@ static struct pcf857x_platform_data pcf857x_data[] = {
 	}
 };
 
-static struct imxi2c_platform_data mx1ads_i2c_data = {
+static const struct imxi2c_platform_data mx1ads_i2c_data __initconst = {
 	.bitrate = 100000,
 };
 
@@ -121,8 +121,8 @@ static void __init mx1ads_init(void)
 		ARRAY_SIZE(mx1ads_pins), "mx1ads");
 
 	/* UART */
-	mxc_register_device(&imx_uart1_device, &uart_pdata[0]);
-	mxc_register_device(&imx_uart2_device, &uart_pdata[1]);
+	imx1_add_imx_uart0(&uart0_pdata);
+	imx1_add_imx_uart1(&uart1_pdata);
 
 	/* Physmap flash */
 	mxc_register_device(&flash_device, &mx1ads_flash_data);
@@ -131,7 +131,7 @@ static void __init mx1ads_init(void)
 	i2c_register_board_info(0, mx1ads_i2c_devices,
 				ARRAY_SIZE(mx1ads_i2c_devices));
 
-	mxc_register_device(&imx_i2c_device, &mx1ads_i2c_data);
+	imx1_add_i2c_imx(&mx1ads_i2c_data);
 }
 
 static void __init mx1ads_timer_init(void)
@@ -145,8 +145,8 @@ struct sys_timer mx1ads_timer = {
 
 MACHINE_START(MX1ADS, "Freescale MX1ADS")
 	/* Maintainer: Sascha Hauer, Pengutronix */
-	.phys_io	= IMX_IO_PHYS,
-	.io_pg_offst	= (IMX_IO_BASE >> 18) & 0xfffc,
+	.phys_io	= MX1_IO_BASE_ADDR,
+	.io_pg_offst	= (MX1_IO_BASE_ADDR_VIRT >> 18) & 0xfffc,
 	.boot_params	= MX1_PHYS_OFFSET + 0x100,
 	.map_io		= mx1_map_io,
 	.init_irq	= mx1_init_irq,
@@ -155,8 +155,8 @@ MACHINE_START(MX1ADS, "Freescale MX1ADS")
 MACHINE_END
 
 MACHINE_START(MXLADS, "Freescale MXLADS")
-	.phys_io	= IMX_IO_PHYS,
-	.io_pg_offst	= (IMX_IO_BASE >> 18) & 0xfffc,
+	.phys_io	= MX1_IO_BASE_ADDR,
+	.io_pg_offst	= (MX1_IO_BASE_ADDR_VIRT >> 18) & 0xfffc,
 	.boot_params	= MX1_PHYS_OFFSET + 0x100,
 	.map_io		= mx1_map_io,
 	.init_irq	= mx1_init_irq,

arch/arm/mach-mx2/mach-mx21ads.c → arch/arm/mach-imx/mach-mx21ads.c

@@ -12,10 +12,6 @@
  * but WITHOUT ANY WARRANTY; without even the implied warranty of
  * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
  * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA  02111-1307  USA
  */
 
 #include <linux/platform_device.h>
@@ -28,15 +24,49 @@
 #include <asm/mach/arch.h>
 #include <asm/mach/time.h>
 #include <asm/mach/map.h>
-#include <mach/imx-uart.h>
 #include <mach/imxfb.h>
 #include <mach/iomux-mx21.h>
 #include <mach/mxc_nand.h>
 #include <mach/mmc.h>
-#include <mach/board-mx21ads.h>
 
+#include "devices-imx21.h"
 #include "devices.h"
 
+/*
+ * Memory-mapped I/O on MX21ADS base board
+ */
+#define MX21ADS_MMIO_BASE_ADDR   0xf5000000
+#define MX21ADS_MMIO_SIZE        SZ_16M
+
+#define MX21ADS_REG_ADDR(offset)    (void __force __iomem *) \
+		(MX21ADS_MMIO_BASE_ADDR + (offset))
+
+#define MX21ADS_CS8900A_IRQ         IRQ_GPIOE(11)
+#define MX21ADS_CS8900A_IOBASE_REG  MX21ADS_REG_ADDR(0x000000)
+#define MX21ADS_ST16C255_IOBASE_REG MX21ADS_REG_ADDR(0x200000)
+#define MX21ADS_VERSION_REG         MX21ADS_REG_ADDR(0x400000)
+#define MX21ADS_IO_REG              MX21ADS_REG_ADDR(0x800000)
+
+/* MX21ADS_IO_REG bit definitions */
+#define MX21ADS_IO_SD_WP        0x0001 /* read */
+#define MX21ADS_IO_TP6          0x0001 /* write */
+#define MX21ADS_IO_SW_SEL       0x0002 /* read */
+#define MX21ADS_IO_TP7          0x0002 /* write */
+#define MX21ADS_IO_RESET_E_UART 0x0004
+#define MX21ADS_IO_RESET_BASE   0x0008
+#define MX21ADS_IO_CSI_CTL2     0x0010
+#define MX21ADS_IO_CSI_CTL1     0x0020
+#define MX21ADS_IO_CSI_CTL0     0x0040
+#define MX21ADS_IO_UART1_EN     0x0080
+#define MX21ADS_IO_UART4_EN     0x0100
+#define MX21ADS_IO_LCDON        0x0200
+#define MX21ADS_IO_IRDA_EN      0x0400
+#define MX21ADS_IO_IRDA_FIR_SEL 0x0800
+#define MX21ADS_IO_IRDA_MD0_B   0x1000
+#define MX21ADS_IO_IRDA_MD1     0x2000
+#define MX21ADS_IO_LED4_ON      0x4000
+#define MX21ADS_IO_LED3_ON      0x8000
+
 static unsigned int mx21ads_pins[] = {
 
 	/* CS8900A */
@@ -133,14 +163,13 @@ static struct platform_device mx21ads_nor_mtd_device = {
 	.resource = &mx21ads_flash_resource,
 };
 
-static struct imxuart_platform_data uart_pdata = {
+static const struct imxuart_platform_data uart_pdata_rts __initconst = {
 	.flags = IMXUART_HAVE_RTSCTS,
 };
 
-static struct imxuart_platform_data uart_norts_pdata = {
+static const struct imxuart_platform_data uart_pdata_norts __initconst = {
 };
 
-
 static int mx21ads_fb_init(struct platform_device *pdev)
 {
 	u16 tmp;
@@ -227,7 +256,8 @@ static struct imxmmc_platform_data mx21ads_sdhc_pdata = {
 	.exit = mx21ads_sdhc_exit,
 };
 
-static struct mxc_nand_platform_data mx21ads_nand_board_info = {
+static const struct mxc_nand_platform_data
+mx21ads_nand_board_info __initconst = {
 	.width = 1,
 	.hw_ecc = 1,
 };
@@ -263,12 +293,12 @@ static void __init mx21ads_board_init(void)
 	mxc_gpio_setup_multiple_pins(mx21ads_pins, ARRAY_SIZE(mx21ads_pins),
 			"mx21ads");
 
-	mxc_register_device(&mxc_uart_device0, &uart_pdata);
-	mxc_register_device(&mxc_uart_device2, &uart_norts_pdata);
-	mxc_register_device(&mxc_uart_device3, &uart_pdata);
+	imx21_add_imx_uart0(&uart_pdata_rts);
+	imx21_add_imx_uart2(&uart_pdata_norts);
+	imx21_add_imx_uart3(&uart_pdata_rts);
 	mxc_register_device(&mxc_fb_device, &mx21ads_fb_data);
 	mxc_register_device(&mxc_sdhc_device0, &mx21ads_sdhc_pdata);
-	mxc_register_device(&imx21_nand_device, &mx21ads_nand_board_info);
+	imx21_add_mxc_nand(&mx21ads_nand_board_info);
 
 	platform_add_devices(platform_devices, ARRAY_SIZE(platform_devices));
 }

arch/arm/mach-mx2/mach-mx27_3ds.c → arch/arm/mach-imx/mach-mx27_3ds.c

@@ -12,23 +12,25 @@
  * but WITHOUT ANY WARRANTY; without even the implied warranty of
  * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
  * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA  02111-1307  USA
+ */
+
+/*
+ * This machine is known as:
+ *  - i.MX27 3-Stack Development System
+ *  - i.MX27 Platform Development Kit (i.MX27 PDK)
  */
 
 #include <linux/platform_device.h>
 #include <linux/gpio.h>
+#include <linux/input/matrix_keypad.h>
 #include <asm/mach-types.h>
 #include <asm/mach/arch.h>
 #include <asm/mach/time.h>
 #include <mach/hardware.h>
 #include <mach/common.h>
-#include <mach/imx-uart.h>
 #include <mach/iomux-mx27.h>
-#include <mach/board-mx27pdk.h>
 
+#include "devices-imx27.h"
 #include "devices.h"
 
 static unsigned int mx27pdk_pins[] = {
@@ -58,7 +60,7 @@ static unsigned int mx27pdk_pins[] = {
 	PF23_AIN_FEC_TX_EN,
 };
 
-static struct imxuart_platform_data uart_pdata = {
+static const struct imxuart_platform_data uart_pdata __initconst = {
 	.flags = IMXUART_HAVE_RTSCTS,
 };
 
@@ -66,12 +68,34 @@ static struct platform_device *platform_devices[] __initdata = {
 	&mxc_fec_device,
 };
 
+/*
+ * Matrix keyboard
+ */
+
+static const uint32_t mx27_3ds_keymap[] = {
+	KEY(0, 0, KEY_UP),
+	KEY(0, 1, KEY_DOWN),
+	KEY(1, 0, KEY_RIGHT),
+	KEY(1, 1, KEY_LEFT),
+	KEY(1, 2, KEY_ENTER),
+	KEY(2, 0, KEY_F6),
+	KEY(2, 1, KEY_F8),
+	KEY(2, 2, KEY_F9),
+	KEY(2, 3, KEY_F10),
+};
+
+static struct matrix_keymap_data mx27_3ds_keymap_data = {
+	.keymap		= mx27_3ds_keymap,
+	.keymap_size	= ARRAY_SIZE(mx27_3ds_keymap),
+};
+
 static void __init mx27pdk_init(void)
 {
 	mxc_gpio_setup_multiple_pins(mx27pdk_pins, ARRAY_SIZE(mx27pdk_pins),
 		"mx27pdk");
-	mxc_register_device(&mxc_uart_device0, &uart_pdata);
+	imx27_add_imx_uart0(&uart_pdata);
 	platform_add_devices(platform_devices, ARRAY_SIZE(platform_devices));
+	mxc_register_device(&imx_kpp_device, &mx27_3ds_keymap_data);
 }
 
 static void __init mx27pdk_timer_init(void)

arch/arm/mach-mx2/mach-mx27ads.c → arch/arm/mach-imx/mach-mx27ads.c

@@ -12,10 +12,6 @@
  * but WITHOUT ANY WARRANTY; without even the implied warranty of
  * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
  * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA  02111-1307  USA
  */
 
 #include <linux/platform_device.h>
@@ -32,16 +28,44 @@
 #include <asm/mach/time.h>
 #include <asm/mach/map.h>
 #include <mach/gpio.h>
-#include <mach/imx-uart.h>
 #include <mach/iomux-mx27.h>
-#include <mach/board-mx27ads.h>
 #include <mach/mxc_nand.h>
-#include <mach/i2c.h>
 #include <mach/imxfb.h>
 #include <mach/mmc.h>
 
+#include "devices-imx27.h"
 #include "devices.h"
 
+/*
+ * Base address of PBC controller, CS4
+ */
+#define PBC_BASE_ADDRESS        0xf4300000
+#define PBC_REG_ADDR(offset)    (void __force __iomem *) \
+		(PBC_BASE_ADDRESS + (offset))
+
+/* When the PBC address connection is fixed in h/w, defined as 1 */
+#define PBC_ADDR_SH             0
+
+/* Offsets for the PBC Controller register */
+/*
+ * PBC Board version register offset
+ */
+#define PBC_VERSION_REG         PBC_REG_ADDR(0x00000 >> PBC_ADDR_SH)
+/*
+ * PBC Board control register 1 set address.
+ */
+#define PBC_BCTRL1_SET_REG      PBC_REG_ADDR(0x00008 >> PBC_ADDR_SH)
+/*
+ * PBC Board control register 1 clear address.
+ */
+#define PBC_BCTRL1_CLEAR_REG    PBC_REG_ADDR(0x0000C >> PBC_ADDR_SH)
+
+/* PBC Board Control Register 1 bit definitions */
+#define PBC_BCTRL1_LCDON        0x0800	/* Enable the LCD */
+
+/* to determine the correct external crystal reference */
+#define CKIH_27MHZ_BIT_SET      (1 << 3)
+
 static unsigned int mx27ads_pins[] = {
 	/* UART0 */
 	PE12_PF_UART1_TXD,
@@ -141,7 +165,8 @@ static unsigned int mx27ads_pins[] = {
 	PB9_PF_SD2_CLK,
 };
 
-static struct mxc_nand_platform_data mx27ads_nand_board_info = {
+static const struct mxc_nand_platform_data
+mx27ads_nand_board_info __initconst = {
 	.width = 1,
 	.hw_ecc = 1,
 };
@@ -168,7 +193,7 @@ static struct platform_device mx27ads_nor_mtd_device = {
 	.resource = &mx27ads_flash_resource,
 };
 
-static struct imxi2c_platform_data mx27ads_i2c_data = {
+static const struct imxi2c_platform_data mx27ads_i2c1_data __initconst = {
 	.bitrate = 100000,
 };
 
@@ -263,20 +288,8 @@ static struct platform_device *platform_devices[] __initdata = {
 	&mxc_w1_master_device,
 };
 
-static struct imxuart_platform_data uart_pdata[] = {
-	{
-		.flags = IMXUART_HAVE_RTSCTS,
-	}, {
-		.flags = IMXUART_HAVE_RTSCTS,
-	}, {
-		.flags = IMXUART_HAVE_RTSCTS,
-	}, {
-		.flags = IMXUART_HAVE_RTSCTS,
-	}, {
-		.flags = IMXUART_HAVE_RTSCTS,
-	}, {
-		.flags = IMXUART_HAVE_RTSCTS,
-	},
+static const struct imxuart_platform_data uart_pdata __initconst = {
+	.flags = IMXUART_HAVE_RTSCTS,
 };
 
 static void __init mx27ads_board_init(void)
@@ -284,18 +297,18 @@ static void __init mx27ads_board_init(void)
 	mxc_gpio_setup_multiple_pins(mx27ads_pins, ARRAY_SIZE(mx27ads_pins),
 			"mx27ads");
 
-	mxc_register_device(&mxc_uart_device0, &uart_pdata[0]);
-	mxc_register_device(&mxc_uart_device1, &uart_pdata[1]);
-	mxc_register_device(&mxc_uart_device2, &uart_pdata[2]);
-	mxc_register_device(&mxc_uart_device3, &uart_pdata[3]);
-	mxc_register_device(&mxc_uart_device4, &uart_pdata[4]);
-	mxc_register_device(&mxc_uart_device5, &uart_pdata[5]);
-	mxc_register_device(&imx27_nand_device, &mx27ads_nand_board_info);
+	imx27_add_imx_uart0(&uart_pdata);
+	imx27_add_imx_uart1(&uart_pdata);
+	imx27_add_imx_uart2(&uart_pdata);
+	imx27_add_imx_uart3(&uart_pdata);
+	imx27_add_imx_uart4(&uart_pdata);
+	imx27_add_imx_uart5(&uart_pdata);
+	imx27_add_mxc_nand(&mx27ads_nand_board_info);
 
 	/* only the i2c master 1 is used on this CPU card */
 	i2c_register_board_info(1, mx27ads_i2c_devices,
 				ARRAY_SIZE(mx27ads_i2c_devices));
-	mxc_register_device(&mxc_i2c_device1, &mx27ads_i2c_data);
+	imx27_add_i2c_imx1(&mx27ads_i2c1_data);
 	mxc_register_device(&mxc_fb_device, &mx27ads_fb_data);
 	mxc_register_device(&mxc_sdhc_device0, &sdhc1_pdata);
 	mxc_register_device(&mxc_sdhc_device1, &sdhc2_pdata);
@@ -342,4 +355,3 @@ MACHINE_START(MX27ADS, "Freescale i.MX27ADS")
 	.init_machine   = mx27ads_board_init,
 	.timer          = &mx27ads_timer,
 MACHINE_END
-

arch/arm/mach-mx2/mach-mxt_td60.c → arch/arm/mach-imx/mach-mxt_td60.c

@@ -12,10 +12,6 @@
  * but WITHOUT ANY WARRANTY; without even the implied warranty of
  * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
  * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA  02111-1307  USA
  */
 
 #include <linux/platform_device.h>
@@ -32,14 +28,13 @@
 #include <asm/mach/time.h>
 #include <asm/mach/map.h>
 #include <linux/gpio.h>
-#include <mach/imx-uart.h>
 #include <mach/iomux-mx27.h>
 #include <mach/mxc_nand.h>
-#include <mach/i2c.h>
 #include <linux/i2c/pca953x.h>
 #include <mach/imxfb.h>
 #include <mach/mmc.h>
 
+#include "devices-imx27.h"
 #include "devices.h"
 
 static unsigned int mxt_td60_pins[] __initdata = {
@@ -128,12 +123,13 @@ static unsigned int mxt_td60_pins[] __initdata = {
 	PB9_PF_SD2_CLK,
 };
 
-static struct mxc_nand_platform_data mxt_td60_nand_board_info = {
+static const struct mxc_nand_platform_data
+mxt_td60_nand_board_info __initconst = {
 	.width = 1,
 	.hw_ecc = 1,
 };
 
-static struct imxi2c_platform_data mxt_td60_i2c_data = {
+static const struct imxi2c_platform_data mxt_td60_i2c0_data __initconst = {
 	.bitrate = 100000,
 };
 
@@ -173,7 +169,7 @@ static struct i2c_board_info mxt_td60_i2c_devices[] = {
 	},
 };
 
-static struct imxi2c_platform_data mxt_td60_i2c2_data = {
+static const struct imxi2c_platform_data mxt_td60_i2c1_data __initconst = {
 	.bitrate = 100000,
 };
 
@@ -239,14 +235,8 @@ static struct platform_device *platform_devices[] __initdata = {
 	&mxc_fec_device,
 };
 
-static struct imxuart_platform_data uart_pdata[] = {
-	{
-		.flags = IMXUART_HAVE_RTSCTS,
-	}, {
-		.flags = IMXUART_HAVE_RTSCTS,
-	}, {
-		.flags = IMXUART_HAVE_RTSCTS,
-	},
+static const struct imxuart_platform_data uart_pdata __initconst = {
+	.flags = IMXUART_HAVE_RTSCTS,
 };
 
 static void __init mxt_td60_board_init(void)
@@ -254,10 +244,10 @@ static void __init mxt_td60_board_init(void)
 	mxc_gpio_setup_multiple_pins(mxt_td60_pins, ARRAY_SIZE(mxt_td60_pins),
 			"MXT_TD60");
 
-	mxc_register_device(&mxc_uart_device0, &uart_pdata[0]);
-	mxc_register_device(&mxc_uart_device1, &uart_pdata[1]);
-	mxc_register_device(&mxc_uart_device2, &uart_pdata[2]);
-	mxc_register_device(&imx27_nand_device, &mxt_td60_nand_board_info);
+	imx27_add_imx_uart0(&uart_pdata);
+	imx27_add_imx_uart1(&uart_pdata);
+	imx27_add_imx_uart2(&uart_pdata);
+	imx27_add_mxc_nand(&mxt_td60_nand_board_info);
 
 	i2c_register_board_info(0, mxt_td60_i2c_devices,
 				ARRAY_SIZE(mxt_td60_i2c_devices));
@@ -265,8 +255,8 @@ static void __init mxt_td60_board_init(void)
 	i2c_register_board_info(1, mxt_td60_i2c2_devices,
 				ARRAY_SIZE(mxt_td60_i2c2_devices));
 
-	mxc_register_device(&mxc_i2c_device0, &mxt_td60_i2c_data);
-	mxc_register_device(&mxc_i2c_device1, &mxt_td60_i2c2_data);
+	imx27_add_i2c_imx0(&mxt_td60_i2c0_data);
+	imx27_add_i2c_imx1(&mxt_td60_i2c1_data);
 	mxc_register_device(&mxc_fb_device, &mxt_td60_fb_data);
 	mxc_register_device(&mxc_sdhc_device0, &sdhc1_pdata);
 

arch/arm/mach-mx2/mach-pca100.c → arch/arm/mach-imx/mach-pca100.c

@@ -36,12 +36,7 @@
 #include <mach/common.h>
 #include <mach/hardware.h>
 #include <mach/iomux-mx27.h>
-#include <mach/i2c.h>
 #include <asm/mach/time.h>
-#if defined(CONFIG_SPI_IMX) || defined(CONFIG_SPI_IMX_MODULE)
-#include <mach/spi.h>
-#endif
-#include <mach/imx-uart.h>
 #include <mach/audmux.h>
 #include <mach/ssi.h>
 #include <mach/mxc_nand.h>
@@ -49,11 +44,16 @@
 #include <mach/mmc.h>
 #include <mach/mxc_ehci.h>
 #include <mach/ulpi.h>
+#include <mach/imxfb.h>
 
+#include "devices-imx27.h"
 #include "devices.h"
 
 #define OTG_PHY_CS_GPIO (GPIO_PORTB + 23)
 #define USBH2_PHY_CS_GPIO (GPIO_PORTB + 24)
+#define SPI1_SS0 (GPIO_PORTD + 28)
+#define SPI1_SS1 (GPIO_PORTD + 27)
+#define SD2_CD (GPIO_PORTC + 29)
 
 static int pca100_pins[] = {
 	/* UART1 */
@@ -68,6 +68,7 @@ static int pca100_pins[] = {
 	PB7_PF_SD2_D3,
 	PB8_PF_SD2_CMD,
 	PB9_PF_SD2_CLK,
+	SD2_CD | GPIO_GPIO | GPIO_IN,
 	/* FEC */
 	PD0_AIN_FEC_TXD0,
 	PD1_AIN_FEC_TXD1,
@@ -131,13 +132,42 @@ static int pca100_pins[] = {
 	PD23_AF_USBH2_DATA2,
 	PD24_AF_USBH2_DATA1,
 	PD26_AF_USBH2_DATA5,
+	/* display */
+	PA5_PF_LSCLK,
+	PA6_PF_LD0,
+	PA7_PF_LD1,
+	PA8_PF_LD2,
+	PA9_PF_LD3,
+	PA10_PF_LD4,
+	PA11_PF_LD5,
+	PA12_PF_LD6,
+	PA13_PF_LD7,
+	PA14_PF_LD8,
+	PA15_PF_LD9,
+	PA16_PF_LD10,
+	PA17_PF_LD11,
+	PA18_PF_LD12,
+	PA19_PF_LD13,
+	PA20_PF_LD14,
+	PA21_PF_LD15,
+	PA22_PF_LD16,
+	PA23_PF_LD17,
+	PA26_PF_PS,
+	PA28_PF_HSYNC,
+	PA29_PF_VSYNC,
+	PA31_PF_OE_ACD,
+	/* free GPIO */
+	GPIO_PORTC | 31 | GPIO_GPIO | GPIO_IN, /* GPIO0_IRQ */
+	GPIO_PORTC | 25 | GPIO_GPIO | GPIO_IN, /* GPIO1_IRQ */
+	GPIO_PORTE | 5 | GPIO_GPIO | GPIO_IN, /* GPIO2_IRQ */
 };
 
-static struct imxuart_platform_data uart_pdata = {
+static const struct imxuart_platform_data uart_pdata __initconst = {
 	.flags = IMXUART_HAVE_RTSCTS,
 };
 
-static struct mxc_nand_platform_data pca100_nand_board_info = {
+static const struct mxc_nand_platform_data
+pca100_nand_board_info __initconst = {
 	.width = 1,
 	.hw_ecc = 1,
 };
@@ -148,7 +178,7 @@ static struct platform_device *platform_devices[] __initdata = {
 	&mxc_wdt,
 };
 
-static struct imxi2c_platform_data pca100_i2c_1_data = {
+static const struct imxi2c_platform_data pca100_i2c1_data __initconst = {
 	.bitrate = 100000,
 };
 
@@ -189,9 +219,9 @@ static struct spi_board_info pca100_spi_board_info[] __initdata = {
 	},
 };
 
-static int pca100_spi_cs[] = {GPIO_PORTD + 28, GPIO_PORTD + 27};
+static int pca100_spi_cs[] = {SPI1_SS0, SPI1_SS1};
 
-static struct spi_imx_master pca100_spi_0_data = {
+static const struct spi_imx_master pca100_spi0_data __initconst = {
 	.chipselect	= pca100_spi_cs,
 	.num_chipselect = ARRAY_SIZE(pca100_spi_cs),
 };
@@ -253,6 +283,7 @@ static struct imxmmc_platform_data sdhc_pdata = {
 	.exit = pca100_sdhc2_exit,
 };
 
+#if defined(CONFIG_USB_ULPI)
 static int otg_phy_init(struct platform_device *pdev)
 {
 	gpio_set_value(OTG_PHY_CS_GPIO, 0);
@@ -276,6 +307,7 @@ static struct mxc_usbh_platform_data usbh2_pdata = {
 	.portsc	= MXC_EHCI_MODE_ULPI,
 	.flags	= MXC_EHCI_INTERFACE_DIFF_UNI,
 };
+#endif
 
 static struct fsl_usb2_platform_data otg_device_pdata = {
 	.operating_mode = FSL_USB2_DR_DEVICE,
@@ -297,6 +329,45 @@ static int __init pca100_otg_mode(char *options)
 }
 __setup("otg_mode=", pca100_otg_mode);
 
+/* framebuffer info */
+static struct imx_fb_videomode pca100_fb_modes[] = {
+	{
+		.mode = {
+			.name		= "EMERGING-ETV570G0DHU",
+			.refresh	= 60,
+			.xres		= 640,
+			.yres		= 480,
+			.pixclock	= 39722, /* in ps (25.175 MHz) */
+			.hsync_len	= 30,
+			.left_margin	= 114,
+			.right_margin	= 16,
+			.vsync_len	= 3,
+			.upper_margin	= 32,
+			.lower_margin	= 0,
+		},
+		/*
+		 * TFT
+		 * Pixel pol active high
+		 * HSYNC active low
+		 * VSYNC active low
+		 * use HSYNC for ACD count
+		 * line clock disable while idle
+		 * always enable line clock even if no data
+		 */
+		.pcr = 0xf0c08080,
+		.bpp = 16,
+	},
+};
+
+static struct imx_fb_platform_data pca100_fb_data = {
+	.mode = pca100_fb_modes,
+	.num_modes = ARRAY_SIZE(pca100_fb_modes),
+
+	.pwmr		= 0x00A903FF,
+	.lscr1		= 0x00120300,
+	.dmacr		= 0x00020010,
+};
+
 static void __init pca100_init(void)
 {
 	int ret;
@@ -320,33 +391,24 @@ static void __init pca100_init(void)
 
 	mxc_register_device(&imx_ssi_device0, &pca100_ssi_pdata);
 
-	mxc_register_device(&mxc_uart_device0, &uart_pdata);
+	imx27_add_imx_uart0(&uart_pdata);
 
-	mxc_gpio_mode(GPIO_PORTC | 29 | GPIO_GPIO | GPIO_IN);
 	mxc_register_device(&mxc_sdhc_device1, &sdhc_pdata);
 
-	mxc_register_device(&imx27_nand_device, &pca100_nand_board_info);
+	imx27_add_mxc_nand(&pca100_nand_board_info);
 
 	/* only the i2c master 1 is used on this CPU card */
 	i2c_register_board_info(1, pca100_i2c_devices,
 				ARRAY_SIZE(pca100_i2c_devices));
 
-	mxc_register_device(&mxc_i2c_device1, &pca100_i2c_1_data);
-
-	mxc_gpio_mode(GPIO_PORTD | 28 | GPIO_GPIO | GPIO_OUT);
-	mxc_gpio_mode(GPIO_PORTD | 27 | GPIO_GPIO | GPIO_OUT);
-
-	/* GPIO0_IRQ */
-	mxc_gpio_mode(GPIO_PORTC | 31 | GPIO_GPIO | GPIO_IN);
-	/* GPIO1_IRQ */
-	mxc_gpio_mode(GPIO_PORTC | 25 | GPIO_GPIO | GPIO_IN);
-	/* GPIO2_IRQ */
-	mxc_gpio_mode(GPIO_PORTE | 5 | GPIO_GPIO | GPIO_IN);
+	imx27_add_i2c_imx1(&pca100_i2c1_data);
 
 #if defined(CONFIG_SPI_IMX) || defined(CONFIG_SPI_IMX_MODULE)
+	mxc_gpio_mode(GPIO_PORTD | 28 | GPIO_GPIO | GPIO_IN);
+	mxc_gpio_mode(GPIO_PORTD | 27 | GPIO_GPIO | GPIO_IN);
 	spi_register_board_info(pca100_spi_board_info,
 				ARRAY_SIZE(pca100_spi_board_info));
-	mxc_register_device(&mxc_spi_device0, &pca100_spi_0_data);
+	imx27_add_spi_imx0(&pca100_spi_0_data);
 #endif
 
 	gpio_request(OTG_PHY_CS_GPIO, "usb-otg-cs");
@@ -372,6 +434,8 @@ static void __init pca100_init(void)
 		mxc_register_device(&mxc_otg_udc_device, &otg_device_pdata);
 	}
 
+	mxc_register_device(&mxc_fb_device, &pca100_fb_data);
+
 	platform_add_devices(platform_devices, ARRAY_SIZE(platform_devices));
 }
 

arch/arm/mach-mx2/mach-pcm038.c → arch/arm/mach-imx/mach-pcm038.c

@@ -35,14 +35,12 @@
 #include <mach/board-pcm038.h>
 #include <mach/common.h>
 #include <mach/hardware.h>
-#include <mach/i2c.h>
 #include <mach/iomux-mx27.h>
-#include <mach/imx-uart.h>
 #include <mach/mxc_nand.h>
-#include <mach/spi.h>
 #include <mach/mxc_ehci.h>
 #include <mach/ulpi.h>
 
+#include "devices-imx27.h"
 #include "devices.h"
 
 static int pcm038_pins[] = {
@@ -162,17 +160,12 @@ static struct platform_device pcm038_nor_mtd_device = {
 	.resource = &pcm038_flash_resource,
 };
 
-static struct imxuart_platform_data uart_pdata[] = {
-	{
-		.flags = IMXUART_HAVE_RTSCTS,
-	}, {
-		.flags = IMXUART_HAVE_RTSCTS,
-	}, {
-		.flags = IMXUART_HAVE_RTSCTS,
-	},
+static const struct imxuart_platform_data uart_pdata __initconst = {
+	.flags = IMXUART_HAVE_RTSCTS,
 };
 
-static struct mxc_nand_platform_data pcm038_nand_board_info = {
+static const struct mxc_nand_platform_data
+pcm038_nand_board_info __initconst = {
 	.width = 1,
 	.hw_ecc = 1,
 };
@@ -192,7 +185,7 @@ static void __init pcm038_init_sram(void)
 	mx27_setup_weimcs(1, 0x0000d843, 0x22252521, 0x22220a00);
 }
 
-static struct imxi2c_platform_data pcm038_i2c_1_data = {
+static const struct imxi2c_platform_data pcm038_i2c1_data __initconst = {
 	.bitrate = 100000,
 };
 
@@ -215,7 +208,7 @@ static struct i2c_board_info pcm038_i2c_devices[] = {
 
 static int pcm038_spi_cs[] = {GPIO_PORTD + 28};
 
-static struct spi_imx_master pcm038_spi_0_data = {
+static const struct spi_imx_master pcm038_spi0_data __initconst = {
 	.chipselect = pcm038_spi_cs,
 	.num_chipselect = ARRAY_SIZE(pcm038_spi_cs),
 };
@@ -305,18 +298,18 @@ static void __init pcm038_init(void)
 
 	pcm038_init_sram();
 
-	mxc_register_device(&mxc_uart_device0, &uart_pdata[0]);
-	mxc_register_device(&mxc_uart_device1, &uart_pdata[1]);
-	mxc_register_device(&mxc_uart_device2, &uart_pdata[2]);
+	imx27_add_imx_uart0(&uart_pdata);
+	imx27_add_imx_uart1(&uart_pdata);
+	imx27_add_imx_uart2(&uart_pdata);
 
 	mxc_gpio_mode(PE16_AF_OWIRE);
-	mxc_register_device(&imx27_nand_device, &pcm038_nand_board_info);
+	imx27_add_mxc_nand(&pcm038_nand_board_info);
 
 	/* only the i2c master 1 is used on this CPU card */
 	i2c_register_board_info(1, pcm038_i2c_devices,
 				ARRAY_SIZE(pcm038_i2c_devices));
 
-	mxc_register_device(&mxc_i2c_device1, &pcm038_i2c_1_data);
+	imx27_add_i2c_imx1(&pcm038_i2c1_data);
 
 	/* PE18 for user-LED D40 */
 	mxc_gpio_mode(GPIO_PORTE | 18 | GPIO_GPIO | GPIO_OUT);
@@ -326,7 +319,7 @@ static void __init pcm038_init(void)
 	/* MC13783 IRQ */
 	mxc_gpio_mode(GPIO_PORTB | 23 | GPIO_GPIO | GPIO_IN);
 
-	mxc_register_device(&mxc_spi_device0, &pcm038_spi_0_data);
+	imx27_add_spi_imx0(&pcm038_spi0_data);
 	spi_register_board_info(pcm038_spi_board_info,
 				ARRAY_SIZE(pcm038_spi_board_info));
 

arch/arm/mach-mx1/mach-scb9328.c → arch/arm/mach-imx/mach-scb9328.c

@@ -22,17 +22,17 @@
 #include <mach/common.h>
 #include <mach/hardware.h>
 #include <mach/irqs.h>
-#include <mach/imx-uart.h>
 #include <mach/iomux-mx1.h>
 
+#include "devices-imx1.h"
 #include "devices.h"
 
 /*
  * This scb9328 has a 32MiB flash
  */
 static struct resource flash_resource = {
-	.start	= IMX_CS0_PHYS,
-	.end	= IMX_CS0_PHYS + (32 * 1024 * 1024) - 1,
+	.start	= MX1_CS0_PHYS,
+	.end	= MX1_CS0_PHYS + (32 * 1024 * 1024) - 1,
 	.flags	= IORESOURCE_MEM,
 };
 
@@ -70,13 +70,13 @@ static struct dm9000_plat_data dm9000_platdata = {
 static struct resource dm9000x_resources[] = {
 	{
 		.name	= "address area",
-		.start	= IMX_CS5_PHYS,
-		.end	= IMX_CS5_PHYS + 1,
+		.start	= MX1_CS5_PHYS,
+		.end	= MX1_CS5_PHYS + 1,
 		.flags	= IORESOURCE_MEM,	/* address access */
 	}, {
 		.name	= "data area",
-		.start	= IMX_CS5_PHYS + 4,
-		.end	= IMX_CS5_PHYS + 5,
+		.start	= MX1_CS5_PHYS + 4,
+		.end	= MX1_CS5_PHYS + 5,
 		.flags	= IORESOURCE_MEM,	/* data access */
 	}, {
 		.start	= IRQ_GPIOC(3),
@@ -108,14 +108,13 @@ static int uart1_mxc_init(struct platform_device *pdev)
 			ARRAY_SIZE(mxc_uart1_pins), "UART1");
 }
 
-static int uart1_mxc_exit(struct platform_device *pdev)
+static void uart1_mxc_exit(struct platform_device *pdev)
 {
 	mxc_gpio_release_multiple_pins(mxc_uart1_pins,
 			ARRAY_SIZE(mxc_uart1_pins));
-	return 0;
 }
 
-static struct imxuart_platform_data uart_pdata = {
+static const struct imxuart_platform_data uart_pdata __initconst = {
 	.init = uart1_mxc_init,
 	.exit = uart1_mxc_exit,
 	.flags = IMXUART_HAVE_RTSCTS,
@@ -131,7 +130,7 @@ static struct platform_device *devices[] __initdata = {
  */
 static void __init scb9328_init(void)
 {
-	mxc_register_device(&imx_uart1_device, &uart_pdata);
+	imx1_add_imx_uart0(&uart_pdata);
 
 	printk(KERN_INFO"Scb9328: Adding devices\n");
 	platform_add_devices(devices, ARRAY_SIZE(devices));

arch/arm/mach-mx1/generic.c → arch/arm/mach-imx/mm-imx1.c

@@ -3,7 +3,7 @@
  *  Created: april 20th, 2004
  *  Copyright: Synertronixx GmbH
  *
- *  Common code for i.MX machines
+ *  Common code for i.MX1 machines
  *
  * This program is free software; you can redistribute it and/or modify
  * it under the terms of the GNU General Public License as published by
@@ -14,11 +14,6 @@
  * but WITHOUT ANY WARRANTY; without even the implied warranty of
  * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
  * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA  02111-1307  USA
- *
  */
 #include <linux/kernel.h>
 #include <linux/init.h>
@@ -31,23 +26,25 @@
 
 static struct map_desc imx_io_desc[] __initdata = {
 	{
-		.virtual	= IMX_IO_BASE,
-		.pfn		= __phys_to_pfn(IMX_IO_PHYS),
-		.length		= IMX_IO_SIZE,
-		.type		= MT_DEVICE
+		.virtual = MX1_IO_BASE_ADDR_VIRT,
+		.pfn = __phys_to_pfn(MX1_IO_BASE_ADDR),
+		.length = MX1_IO_SIZE,
+		.type = MT_DEVICE
 	}
 };
 
 void __init mx1_map_io(void)
 {
 	mxc_set_cpu_type(MXC_CPU_MX1);
-	mxc_arch_reset_init(IO_ADDRESS(WDT_BASE_ADDR));
+	mxc_arch_reset_init(MX1_IO_ADDRESS(MX1_WDT_BASE_ADDR));
 
 	iotable_init(imx_io_desc, ARRAY_SIZE(imx_io_desc));
 }
 
+int imx1_register_gpios(void);
+
 void __init mx1_init_irq(void)
 {
-	mxc_init_irq(IO_ADDRESS(AVIC_BASE_ADDR));
+	mxc_init_irq(MX1_IO_ADDRESS(MX1_AVIC_BASE_ADDR));
+	imx1_register_gpios();
 }
-

arch/arm/mach-mx2/mm-imx21.c → arch/arm/mach-imx/mm-imx21.c

 /*
- * arch/arm/mach-mx2/mm-imx21.c
+ * arch/arm/mach-imx/mm-imx21.c
  *
  * Copyright (C) 2008 Juergen Beisert (kernel@pengutronix.de)
  *
@@ -77,7 +77,10 @@ void __init mx21_map_io(void)
 	iotable_init(imx21_io_desc, ARRAY_SIZE(imx21_io_desc));
 }
 
+int imx21_register_gpios(void);
+
 void __init mx21_init_irq(void)
 {
 	mxc_init_irq(MX21_IO_ADDRESS(MX21_AVIC_BASE_ADDR));
+	imx21_register_gpios();
 }

arch/arm/mach-mx2/mm-imx27.c → arch/arm/mach-imx/mm-imx27.c

 /*
- * arch/arm/mach-mx2/mm-imx27.c
+ * arch/arm/mach-imx/mm-imx27.c
  *
  * Copyright (C) 2008 Juergen Beisert (kernel@pengutronix.de)
  *
@@ -77,7 +77,10 @@ void __init mx27_map_io(void)
 	iotable_init(imx27_io_desc, ARRAY_SIZE(imx27_io_desc));
 }
 
+int imx27_register_gpios(void);
+
 void __init mx27_init_irq(void)
 {
 	mxc_init_irq(MX27_IO_ADDRESS(MX27_AVIC_BASE_ADDR));
+	imx27_register_gpios();
 }

arch/arm/mach-imx/pm-imx27.c

+/*
+ * i.MX27 Power Management Routines
+ *
+ * Based on Freescale's BSP
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License.
+ */
+
+#include <linux/kernel.h>
+#include <linux/suspend.h>
+#include <linux/io.h>
+#include <mach/system.h>
+#include <mach/mx27.h>
+
+static int mx27_suspend_enter(suspend_state_t state)
+{
+	u32 cscr;
+	switch (state) {
+	case PM_SUSPEND_MEM:
+		/* Clear MPEN and SPEN to disable MPLL/SPLL */
+		cscr = __raw_readl(MX27_IO_ADDRESS(MX27_CCM_BASE_ADDR));
+		cscr &= 0xFFFFFFFC;
+		__raw_writel(cscr, MX27_IO_ADDRESS(MX27_CCM_BASE_ADDR));
+		/* Executes WFI */
+		arch_idle();
+		break;
+
+	default:
+		return -EINVAL;
+	}
+	return 0;
+}
+
+static struct platform_suspend_ops mx27_suspend_ops = {
+	.enter = mx27_suspend_enter,
+	.valid = suspend_valid_only_mem,
+};
+
+static int __init mx27_pm_init(void)
+{
+	suspend_set_ops(&mx27_suspend_ops);
+	return 0;
+}
+
+device_initcall(mx27_pm_init);

arch/arm/mach-kirkwood/Kconfig

@@ -75,6 +75,13 @@ config MACH_OPENRD_CLIENT
 	  Say 'Y' here if you want your kernel to support the
 	  Marvell OpenRD Client Board.
 
+config MACH_OPENRD_ULTIMATE
+	bool "Marvell OpenRD Ultimate Board"
+	select MACH_OPENRD
+	help
+	  Say 'Y' here if you want your kernel to support the
+	  Marvell OpenRD Ultimate Board.
+
 config MACH_NETSPACE_V2
 	bool "LaCie Network Space v2 NAS Board"
 	help
@@ -87,6 +94,12 @@ config MACH_INETSPACE_V2
 	  Say 'Y' here if you want your kernel to support the
 	  LaCie Internet Space v2 NAS.
 
+config MACH_NETSPACE_MAX_V2
+	bool "LaCie Network Space Max v2 NAS Board"
+	help
+	  Say 'Y' here if you want your kernel to support the
+	  LaCie Network Space Max v2 NAS.
+
 config MACH_NET2BIG_V2
 	bool "LaCie 2Big Network v2 NAS Board"
 	help
@@ -99,6 +112,12 @@ config MACH_NET5BIG_V2
 	  Say 'Y' here if you want your kernel to support the
 	  LaCie 5Big Network v2 NAS.
 
+config MACH_T5325
+	bool "HP t5325 Thin Client"
+	help
+	  Say 'Y' here if you want your kernel to support the
+	  HP t5325 Thin Client.
+
 endmenu
 
 endif

arch/arm/mach-kirkwood/Makefile

@@ -12,7 +12,9 @@ obj-$(CONFIG_MACH_TS41X)		+= ts41x-setup.o tsx1x-common.o
 obj-$(CONFIG_MACH_OPENRD)		+= openrd-setup.o
 obj-$(CONFIG_MACH_NETSPACE_V2)		+= netspace_v2-setup.o
 obj-$(CONFIG_MACH_INETSPACE_V2)		+= netspace_v2-setup.o
+obj-$(CONFIG_MACH_NETSPACE_MAX_V2)	+= netspace_v2-setup.o
 obj-$(CONFIG_MACH_NET2BIG_V2)		+= netxbig_v2-setup.o
 obj-$(CONFIG_MACH_NET5BIG_V2)		+= netxbig_v2-setup.o
+obj-$(CONFIG_MACH_T5325)		+= t5325-setup.o
 
 obj-$(CONFIG_CPU_IDLE)			+= cpuidle.o

arch/arm/mach-kirkwood/addr-map.c

@@ -31,6 +31,8 @@
 #define ATTR_DEV_CS0		0x3e
 #define ATTR_PCIE_IO		0xe0
 #define ATTR_PCIE_MEM		0xe8
+#define ATTR_PCIE1_IO		0xd0
+#define ATTR_PCIE1_MEM		0xd8
 #define ATTR_SRAM		0x01
 
 /*
@@ -106,17 +108,21 @@ void __init kirkwood_setup_cpu_mbus(void)
 		      TARGET_PCIE, ATTR_PCIE_IO, KIRKWOOD_PCIE_IO_BUS_BASE);
 	setup_cpu_win(1, KIRKWOOD_PCIE_MEM_PHYS_BASE, KIRKWOOD_PCIE_MEM_SIZE,
 		      TARGET_PCIE, ATTR_PCIE_MEM, KIRKWOOD_PCIE_MEM_BUS_BASE);
+	setup_cpu_win(2, KIRKWOOD_PCIE1_IO_PHYS_BASE, KIRKWOOD_PCIE1_IO_SIZE,
+		      TARGET_PCIE, ATTR_PCIE1_IO, KIRKWOOD_PCIE1_IO_BUS_BASE);
+	setup_cpu_win(3, KIRKWOOD_PCIE1_MEM_PHYS_BASE, KIRKWOOD_PCIE1_MEM_SIZE,
+		      TARGET_PCIE, ATTR_PCIE1_MEM, KIRKWOOD_PCIE1_MEM_BUS_BASE);
 
 	/*
 	 * Setup window for NAND controller.
 	 */
-	setup_cpu_win(2, KIRKWOOD_NAND_MEM_PHYS_BASE, KIRKWOOD_NAND_MEM_SIZE,
+	setup_cpu_win(4, KIRKWOOD_NAND_MEM_PHYS_BASE, KIRKWOOD_NAND_MEM_SIZE,
 		      TARGET_DEV_BUS, ATTR_DEV_NAND, -1);
 
 	/*
 	 * Setup window for SRAM.
 	 */
-	setup_cpu_win(3, KIRKWOOD_SRAM_PHYS_BASE, KIRKWOOD_SRAM_SIZE,
+	setup_cpu_win(5, KIRKWOOD_SRAM_PHYS_BASE, KIRKWOOD_SRAM_SIZE,
 		      TARGET_SRAM, ATTR_SRAM, -1);
 
 	/*

arch/arm/mach-kirkwood/common.c

@@ -43,6 +43,11 @@ static struct map_desc kirkwood_io_desc[] __initdata = {
 		.pfn		= __phys_to_pfn(KIRKWOOD_PCIE_IO_PHYS_BASE),
 		.length		= KIRKWOOD_PCIE_IO_SIZE,
 		.type		= MT_DEVICE,
+	}, {
+		.virtual	= KIRKWOOD_PCIE1_IO_VIRT_BASE,
+		.pfn		= __phys_to_pfn(KIRKWOOD_PCIE1_IO_PHYS_BASE),
+		.length		= KIRKWOOD_PCIE1_IO_SIZE,
+		.type		= MT_DEVICE,
 	}, {
 		.virtual	= KIRKWOOD_REGS_VIRT_BASE,
 		.pfn		= __phys_to_pfn(KIRKWOOD_REGS_PHYS_BASE),
@@ -402,7 +407,7 @@ void __init kirkwood_sdio_init(struct mvsdio_platform_data *mvsdio_data)
 	u32 dev, rev;
 
 	kirkwood_pcie_id(&dev, &rev);
-	if (rev == 0)  /* catch all Kirkwood Z0's */
+	if (rev == 0 && dev != MV88F6282_DEV_ID) /* catch all Kirkwood Z0's */
 		mvsdio_data->clock = 100000000;
 	else
 		mvsdio_data->clock = 200000000;
@@ -847,8 +852,10 @@ int __init kirkwood_find_tclk(void)
 	u32 dev, rev;
 
 	kirkwood_pcie_id(&dev, &rev);
-	if (dev == MV88F6281_DEV_ID && (rev == MV88F6281_REV_A0 ||
-					rev == MV88F6281_REV_A1))
+
+	if ((dev == MV88F6281_DEV_ID && (rev == MV88F6281_REV_A0 ||
+					rev == MV88F6281_REV_A1)) ||
+	    (dev == MV88F6282_DEV_ID))
 		return 200000000;
 
 	return 166666667;
@@ -891,13 +898,22 @@ static char * __init kirkwood_id(void)
 			return "MV88F6192-Z0";
 		else if (rev == MV88F6192_REV_A0)
 			return "MV88F6192-A0";
+		else if (rev == MV88F6192_REV_A1)
+			return "MV88F6192-A1";
 		else
 			return "MV88F6192-Rev-Unsupported";
 	} else if (dev == MV88F6180_DEV_ID) {
 		if (rev == MV88F6180_REV_A0)
 			return "MV88F6180-Rev-A0";
+		else if (rev == MV88F6180_REV_A1)
+			return "MV88F6180-Rev-A1";
 		else
 			return "MV88F6180-Rev-Unsupported";
+	} else if (dev == MV88F6282_DEV_ID) {
+		if (rev == MV88F6282_REV_A0)
+			return "MV88F6282-Rev-A0";
+		else
+			return "MV88F6282-Rev-Unsupported";
 	} else {
 		return "Device-Unknown";
 	}
@@ -949,12 +965,14 @@ void __init kirkwood_init(void)
 static int __init kirkwood_clock_gate(void)
 {
 	unsigned int curr = readl(CLOCK_GATING_CTRL);
+	u32 dev, rev;
 
+	kirkwood_pcie_id(&dev, &rev);
 	printk(KERN_DEBUG "Gating clock of unused units\n");
 	printk(KERN_DEBUG "before: 0x%08x\n", curr);
 
 	/* Make sure those units are accessible */
-	writel(curr | CGC_SATA0 | CGC_SATA1 | CGC_PEX0, CLOCK_GATING_CTRL);
+	writel(curr | CGC_SATA0 | CGC_SATA1 | CGC_PEX0 | CGC_PEX1, CLOCK_GATING_CTRL);
 
 	/* For SATA: first shutdown the phy */
 	if (!(kirkwood_clk_ctrl & CGC_SATA0)) {
@@ -979,6 +997,18 @@ static int __init kirkwood_clock_gate(void)
 		writel(readl(PCIE_LINK_CTRL) & ~0x10, PCIE_LINK_CTRL);
 	}
 
+	/* For PCIe 1: first shutdown the phy */
+	if (dev == MV88F6282_DEV_ID) {
+		if (!(kirkwood_clk_ctrl & CGC_PEX1)) {
+			writel(readl(PCIE1_LINK_CTRL) | 0x10, PCIE1_LINK_CTRL);
+			while (1)
+				if (readl(PCIE1_STATUS) & 0x1)
+					break;
+			writel(readl(PCIE1_LINK_CTRL) & ~0x10, PCIE1_LINK_CTRL);
+		}
+	} else  /* keep this bit set for devices that don't have PCIe1 */
+		kirkwood_clk_ctrl |= CGC_PEX1;
+
 	/* Now gate clock the required units */
 	writel(kirkwood_clk_ctrl, CLOCK_GATING_CTRL);
 	printk(KERN_DEBUG " after: 0x%08x\n", readl(CLOCK_GATING_CTRL));

arch/arm/mach-kirkwood/common.h

@@ -18,6 +18,9 @@ struct mvsdio_platform_data;
 struct mtd_partition;
 struct mtd_info;
 
+#define KW_PCIE0	(1 << 0)
+#define KW_PCIE1	(1 << 1)
+
 /*
  * Basic Kirkwood init functions used early by machine-setup.
  */
@@ -34,7 +37,7 @@ void kirkwood_ehci_init(void);
 void kirkwood_ge00_init(struct mv643xx_eth_platform_data *eth_data);
 void kirkwood_ge01_init(struct mv643xx_eth_platform_data *eth_data);
 void kirkwood_ge00_switch_init(struct dsa_platform_data *d, int irq);
-void kirkwood_pcie_init(void);
+void kirkwood_pcie_init(unsigned int portmask);
 void kirkwood_sata_init(struct mv_sata_platform_data *sata_data);
 void kirkwood_sdio_init(struct mvsdio_platform_data *mvsdio_data);
 void kirkwood_spi_init(void);

arch/arm/mach-kirkwood/db88f6281-bp-setup.c

@@ -51,6 +51,14 @@ static struct mvsdio_platform_data db88f6281_mvsdio_data = {
 };
 
 static unsigned int db88f6281_mpp_config[] __initdata = {
+	MPP0_NF_IO2,
+	MPP1_NF_IO3,
+	MPP2_NF_IO4,
+	MPP3_NF_IO5,
+	MPP4_NF_IO6,
+	MPP5_NF_IO7,
+	MPP18_NF_IO0,
+	MPP19_NF_IO1,
 	MPP37_GPIO,
 	MPP38_GPIO,
 	0
@@ -74,9 +82,15 @@ static void __init db88f6281_init(void)
 
 static int __init db88f6281_pci_init(void)
 {
-	if (machine_is_db88f6281_bp())
-		kirkwood_pcie_init();
+	if (machine_is_db88f6281_bp()) {
+		u32 dev, rev;
 
+		kirkwood_pcie_id(&dev, &rev);
+		if (dev == MV88F6282_DEV_ID)
+			kirkwood_pcie_init(KW_PCIE1 | KW_PCIE0);
+		else
+			kirkwood_pcie_init(KW_PCIE0);
+	}
 	return 0;
 }
 subsys_initcall(db88f6281_pci_init);

arch/arm/mach-kirkwood/include/mach/bridge-regs.h

@@ -59,8 +59,9 @@
 #define CGC_SATA1		(1 << 15)
 #define CGC_XOR1		(1 << 16)
 #define CGC_CRYPTO		(1 << 17)
+#define CGC_PEX1		(1 << 18)
 #define CGC_GE1			(1 << 19)
 #define CGC_TDM			(1 << 20)
-#define CGC_RESERVED		((1 << 18) | (0x6 << 21))
+#define CGC_RESERVED		(0x6 << 21)
 
 #endif

arch/arm/mach-kirkwood/include/mach/irqs.h

@@ -23,6 +23,7 @@
 #define IRQ_KIRKWOOD_XOR_10	7
 #define IRQ_KIRKWOOD_XOR_11	8
 #define IRQ_KIRKWOOD_PCIE	9
+#define IRQ_KIRKWOOD_PCIE1	10
 #define IRQ_KIRKWOOD_GE00_SUM	11
 #define IRQ_KIRKWOOD_GE01_SUM	15
 #define IRQ_KIRKWOOD_USB	19

arch/arm/mach-kirkwood/include/mach/kirkwood.h

@@ -16,36 +16,48 @@
  * Marvell Kirkwood address maps.
  *
  * phys
- * e0000000	PCIe Memory space
+ * e0000000	PCIe #0 Memory space
+ * e8000000	PCIe #1 Memory space
  * f1000000	on-chip peripheral registers
- * f2000000	PCIe I/O space
- * f3000000	NAND controller address window
- * f4000000	Security Accelerator SRAM
+ * f2000000	PCIe #0 I/O space
+ * f3000000	PCIe #1 I/O space
+ * f4000000	NAND controller address window
+ * f5000000	Security Accelerator SRAM
  *
  * virt		phys		size
- * fee00000	f1000000	1M	on-chip peripheral registers
- * fef00000	f2000000	1M	PCIe I/O space
+ * fed00000	f1000000	1M	on-chip peripheral registers
+ * fee00000	f2000000	1M	PCIe #0 I/O space
+ * fef00000	f3000000	1M	PCIe #1 I/O space
  */
 
-#define KIRKWOOD_SRAM_PHYS_BASE		0xf4000000
+#define KIRKWOOD_SRAM_PHYS_BASE		0xf5000000
 #define KIRKWOOD_SRAM_SIZE		SZ_2K
 
-#define KIRKWOOD_NAND_MEM_PHYS_BASE	0xf3000000
+#define KIRKWOOD_NAND_MEM_PHYS_BASE	0xf4000000
 #define KIRKWOOD_NAND_MEM_SIZE		SZ_1K
 
+#define KIRKWOOD_PCIE1_IO_PHYS_BASE	0xf3000000
+#define KIRKWOOD_PCIE1_IO_VIRT_BASE	0xfef00000
+#define KIRKWOOD_PCIE1_IO_BUS_BASE	0x00000000
+#define KIRKWOOD_PCIE1_IO_SIZE		SZ_1M
+
 #define KIRKWOOD_PCIE_IO_PHYS_BASE	0xf2000000
-#define KIRKWOOD_PCIE_IO_VIRT_BASE	0xfef00000
+#define KIRKWOOD_PCIE_IO_VIRT_BASE	0xfee00000
 #define KIRKWOOD_PCIE_IO_BUS_BASE	0x00000000
 #define KIRKWOOD_PCIE_IO_SIZE		SZ_1M
 
 #define KIRKWOOD_REGS_PHYS_BASE		0xf1000000
-#define KIRKWOOD_REGS_VIRT_BASE		0xfee00000
+#define KIRKWOOD_REGS_VIRT_BASE		0xfed00000
 #define KIRKWOOD_REGS_SIZE		SZ_1M
 
 #define KIRKWOOD_PCIE_MEM_PHYS_BASE	0xe0000000
 #define KIRKWOOD_PCIE_MEM_BUS_BASE	0xe0000000
 #define KIRKWOOD_PCIE_MEM_SIZE		SZ_128M
 
+#define KIRKWOOD_PCIE1_MEM_PHYS_BASE	0xe8000000
+#define KIRKWOOD_PCIE1_MEM_BUS_BASE	0xe8000000
+#define KIRKWOOD_PCIE1_MEM_SIZE		SZ_128M
+
 /*
  * Register Map
  */
@@ -72,6 +84,9 @@
 #define PCIE_VIRT_BASE		(KIRKWOOD_REGS_VIRT_BASE | 0x40000)
 #define PCIE_LINK_CTRL		(PCIE_VIRT_BASE | 0x70)
 #define PCIE_STATUS		(PCIE_VIRT_BASE | 0x1a04)
+#define PCIE1_VIRT_BASE		(KIRKWOOD_REGS_VIRT_BASE | 0x44000)
+#define PCIE1_LINK_CTRL		(PCIE1_VIRT_BASE | 0x70)
+#define PCIE1_STATUS		(PCIE1_VIRT_BASE | 0x1a04)
 
 #define USB_PHYS_BASE		(KIRKWOOD_REGS_PHYS_BASE | 0x50000)
 
@@ -107,8 +122,12 @@
 #define MV88F6192_DEV_ID	0x6192
 #define MV88F6192_REV_Z0	0
 #define MV88F6192_REV_A0	2
+#define MV88F6192_REV_A1	3
 
 #define MV88F6180_DEV_ID	0x6180
 #define MV88F6180_REV_A0	2
+#define MV88F6180_REV_A1	3
 
+#define MV88F6282_DEV_ID	0x6282
+#define MV88F6282_REV_A0	0
 #endif

arch/arm/mach-kirkwood/include/mach/leds-ns2.h

+/*
+ * arch/arm/mach-kirkwood/include/mach/leds-ns2.h
+ *
+ * Platform data structure for Network Space v2 LED driver
+ *
+ * This file is licensed under the terms of the GNU General Public
+ * License version 2.  This program is licensed "as is" without any
+ * warranty of any kind, whether express or implied.
+ */
+
+#ifndef __MACH_LEDS_NS2_H
+#define __MACH_LEDS_NS2_H
+
+struct ns2_led {
+	const char	*name;
+	const char	*default_trigger;
+	unsigned	cmd;
+	unsigned	slow;
+};
+
+struct ns2_led_platform_data {
+	int		num_leds;
+	struct ns2_led	*leds;
+};
+
+#endif /* __MACH_LEDS_NS2_H */

arch/arm/mach-kirkwood/mpp.c

@@ -23,7 +23,8 @@ static unsigned int __init kirkwood_variant(void)
 
 	kirkwood_pcie_id(&dev, &rev);
 
-	if (dev == MV88F6281_DEV_ID && rev >= MV88F6281_REV_A0)
+	if ((dev == MV88F6281_DEV_ID && rev >= MV88F6281_REV_A0) ||
+	    (dev == MV88F6282_DEV_ID))
 		return MPP_F6281_MASK;
 	if (dev == MV88F6192_DEV_ID && rev >= MV88F6192_REV_A0)
 		return MPP_F6192_MASK;

arch/arm/mach-kirkwood/mv88f6281gtw_ge-setup.c

@@ -155,7 +155,7 @@ static void __init mv88f6281gtw_ge_init(void)
 static int __init mv88f6281gtw_ge_pci_init(void)
 {
 	if (machine_is_mv88f6281gtw_ge())
-		kirkwood_pcie_init();
+		kirkwood_pcie_init(KW_PCIE0);
 
 	return 0;
 }

arch/arm/mach-kirkwood/netspace_v2-setup.c

@@ -39,6 +39,7 @@
 #include <asm/mach/arch.h>
 #include <asm/mach/time.h>
 #include <mach/kirkwood.h>
+#include <mach/leds-ns2.h>
 #include <plat/time.h>
 #include "common.h"
 #include "mpp.h"
@@ -126,6 +127,18 @@ static void __init netspace_v2_sata_power_init(void)
 	}
 	if (err)
 		pr_err("netspace_v2: failed to setup SATA0 power\n");
+
+	if (machine_is_netspace_max_v2()) {
+		err = gpio_request(NETSPACE_V2_GPIO_SATA1_POWER, "SATA1 power");
+		if (err == 0) {
+			err = gpio_direction_output(
+					NETSPACE_V2_GPIO_SATA1_POWER, 1);
+			if (err)
+				gpio_free(NETSPACE_V2_GPIO_SATA1_POWER);
+		}
+		if (err)
+			pr_err("netspace_v2: failed to setup SATA1 power\n");
+	}
 }
 
 /*****************************************************************************
@@ -160,36 +173,12 @@ static struct platform_device netspace_v2_gpio_buttons = {
  * GPIO LEDs
  ****************************************************************************/
 
-/*
- * The blue front LED is wired to a CPLD and can blink in relation with the
- * SATA activity.
- *
- * The following array detail the different LED registers and the combination
- * of their possible values:
- *
- *  cmd_led   |  slow_led  | /SATA active | LED state
- *            |            |              |
- *     1      |     0      |      x       |  off
- *     -      |     1      |      x       |  on
- *     0      |     0      |      1       |  on
- *     0      |     0      |      0       |  blink (rate 300ms)
- */
-
 #define NETSPACE_V2_GPIO_RED_LED	12
-#define NETSPACE_V2_GPIO_BLUE_LED_SLOW	29
-#define NETSPACE_V2_GPIO_BLUE_LED_CMD	30
-
 
 static struct gpio_led netspace_v2_gpio_led_pins[] = {
 	{
-		.name			= "ns_v2:blue:sata",
-		.default_trigger	= "default-on",
-		.gpio			= NETSPACE_V2_GPIO_BLUE_LED_CMD,
-		.active_low		= 1,
-	},
-	{
-		.name			= "ns_v2:red:fail",
-		.gpio			= NETSPACE_V2_GPIO_RED_LED,
+		.name	= "ns_v2:red:fail",
+		.gpio	= NETSPACE_V2_GPIO_RED_LED,
 	},
 };
 
@@ -206,22 +195,33 @@ static struct platform_device netspace_v2_gpio_leds = {
 	},
 };
 
-static void __init netspace_v2_gpio_leds_init(void)
-{
-	int err;
+/*****************************************************************************
+ * Dual-GPIO CPLD LEDs
+ ****************************************************************************/
 
-	/* Configure register slow_led to allow SATA activity LED blinking */
-	err = gpio_request(NETSPACE_V2_GPIO_BLUE_LED_SLOW, "blue LED slow");
-	if (err == 0) {
-		err = gpio_direction_output(NETSPACE_V2_GPIO_BLUE_LED_SLOW, 0);
-		if (err)
-			gpio_free(NETSPACE_V2_GPIO_BLUE_LED_SLOW);
-	}
-	if (err)
-		pr_err("netspace_v2: failed to configure blue LED slow GPIO\n");
+#define NETSPACE_V2_GPIO_BLUE_LED_SLOW	29
+#define NETSPACE_V2_GPIO_BLUE_LED_CMD	30
 
-	platform_device_register(&netspace_v2_gpio_leds);
-}
+static struct ns2_led netspace_v2_led_pins[] = {
+	{
+		.name	= "ns_v2:blue:sata",
+		.cmd	= NETSPACE_V2_GPIO_BLUE_LED_CMD,
+		.slow	= NETSPACE_V2_GPIO_BLUE_LED_SLOW,
+	},
+};
+
+static struct ns2_led_platform_data netspace_v2_leds_data = {
+	.num_leds	= ARRAY_SIZE(netspace_v2_led_pins),
+	.leds		= netspace_v2_led_pins,
+};
+
+static struct platform_device netspace_v2_leds = {
+	.name		= "leds-ns2",
+	.id		= -1,
+	.dev		= {
+		.platform_data	= &netspace_v2_leds_data,
+	},
+};
 
 /*****************************************************************************
  * Timer
@@ -249,17 +249,21 @@ static unsigned int netspace_v2_mpp_config[] __initdata = {
 	MPP4_NF_IO6,
 	MPP5_NF_IO7,
 	MPP6_SYSRST_OUTn,
-	MPP8_TW_SDA,
-	MPP9_TW_SCK,
+	MPP7_GPO,		/* Fan speed (bit 1) */
+	MPP8_TW0_SDA,
+	MPP9_TW0_SCK,
 	MPP10_UART0_TXD,
 	MPP11_UART0_RXD,
 	MPP12_GPO,		/* Red led */
 	MPP14_GPIO,		/* USB fuse */
 	MPP16_GPIO,		/* SATA 0 power */
+	MPP17_GPIO,		/* SATA 1 power */
 	MPP18_NF_IO0,
 	MPP19_NF_IO1,
 	MPP20_SATA1_ACTn,
 	MPP21_SATA0_ACTn,
+	MPP22_GPIO,		/* Fan speed (bit 0) */
+	MPP23_GPIO,		/* Fan power */
 	MPP24_GPIO,		/* USB mode select */
 	MPP25_GPIO,		/* Fan rotation fail */
 	MPP26_GPIO,		/* USB device vbus */
@@ -268,6 +272,7 @@ static unsigned int netspace_v2_mpp_config[] __initdata = {
 	MPP30_GPIO,		/* Blue led (command register) */
 	MPP31_GPIO,		/* Board power off */
 	MPP32_GPIO, 		/* Power button (0 = Released, 1 = Pushed) */
+	MPP33_GPO,		/* Fan speed (bit 2) */
 	0
 };
 
@@ -299,7 +304,8 @@ static void __init netspace_v2_init(void)
 	i2c_register_board_info(0, netspace_v2_i2c_info,
 				ARRAY_SIZE(netspace_v2_i2c_info));
 
-	netspace_v2_gpio_leds_init();
+	platform_device_register(&netspace_v2_leds);
+	platform_device_register(&netspace_v2_gpio_leds);
 	platform_device_register(&netspace_v2_gpio_buttons);
 
 	if (gpio_request(NETSPACE_V2_GPIO_POWER_OFF, "power-off") == 0 &&
@@ -332,3 +338,15 @@ MACHINE_START(INETSPACE_V2, "LaCie Internet Space v2")
 	.timer		= &netspace_v2_timer,
 MACHINE_END
 #endif
+
+#ifdef CONFIG_MACH_NETSPACE_MAX_V2
+MACHINE_START(NETSPACE_MAX_V2, "LaCie Network Space Max v2")
+	.phys_io	= KIRKWOOD_REGS_PHYS_BASE,
+	.io_pg_offst	= ((KIRKWOOD_REGS_VIRT_BASE) >> 18) & 0xfffc,
+	.boot_params	= 0x00000100,
+	.init_machine	= netspace_v2_init,
+	.map_io		= kirkwood_map_io,
+	.init_irq	= kirkwood_init_irq,
+	.timer		= &netspace_v2_timer,
+MACHINE_END
+#endif

arch/arm/mach-kirkwood/netxbig_v2-setup.c

@@ -270,8 +270,8 @@ static unsigned int net2big_v2_mpp_config[] __initdata = {
 	MPP3_SPI_MISO,
 	MPP6_SYSRST_OUTn,
 	MPP7_GPO,		/* Request power-off */
-	MPP8_TW_SDA,
-	MPP9_TW_SCK,
+	MPP8_TW0_SDA,
+	MPP9_TW0_SCK,
 	MPP10_UART0_TXD,
 	MPP11_UART0_RXD,
 	MPP13_GPIO,		/* Rear power switch (on|auto) */
@@ -306,8 +306,8 @@ static unsigned int net5big_v2_mpp_config[] __initdata = {
 	MPP3_SPI_MISO,
 	MPP6_SYSRST_OUTn,
 	MPP7_GPO,		/* Request power-off */
-	MPP8_TW_SDA,
-	MPP9_TW_SCK,
+	MPP8_TW0_SDA,
+	MPP9_TW0_SCK,
 	MPP10_UART0_TXD,
 	MPP11_UART0_RXD,
 	MPP13_GPIO,		/* Rear power switch (on|auto) */
@@ -315,20 +315,20 @@ static unsigned int net5big_v2_mpp_config[] __initdata = {
 	MPP15_GPIO,		/* Rear power switch (auto|off) */
 	MPP16_GPIO,		/* SATA HDD1 power */
 	MPP17_GPIO,		/* SATA HDD2 power */
-	MPP20_GE1_0,
-	MPP21_GE1_1,
-	MPP22_GE1_2,
-	MPP23_GE1_3,
-	MPP24_GE1_4,
-	MPP25_GE1_5,
-	MPP26_GE1_6,
-	MPP27_GE1_7,
+	MPP20_GE1_TXD0,
+	MPP21_GE1_TXD1,
+	MPP22_GE1_TXD2,
+	MPP23_GE1_TXD3,
+	MPP24_GE1_RXD0,
+	MPP25_GE1_RXD1,
+	MPP26_GE1_RXD2,
+	MPP27_GE1_RXD3,
 	MPP28_GPIO,		/* USB enable host vbus */
 	MPP29_GPIO,		/* CPLD extension ALE */
-	MPP30_GE1_10,
-	MPP31_GE1_11,
-	MPP32_GE1_12,
-	MPP33_GE1_13,
+	MPP30_GE1_RXCTL,
+	MPP31_GE1_RXCLK,
+	MPP32_GE1_TCLKOUT,
+	MPP33_GE1_TXCTL,
 	MPP34_GPIO,		/* Rear Push button */
 	MPP35_GPIO,		/* Inhibit switch power-off */
 	MPP36_GPIO,		/* SATA HDD1 presence */

arch/arm/mach-kirkwood/rd88f6192-nas-setup.c

@@ -71,7 +71,7 @@ static void __init rd88f6192_init(void)
 static int __init rd88f6192_pci_init(void)
 {
 	if (machine_is_rd88f6192_nas())
-		kirkwood_pcie_init();
+		kirkwood_pcie_init(KW_PCIE0);
 
 	return 0;
 }

arch/arm/mach-kirkwood/rd88f6281-setup.c

@@ -107,7 +107,7 @@ static void __init rd88f6281_init(void)
 static int __init rd88f6281_pci_init(void)
 {
 	if (machine_is_rd88f6281())
-		kirkwood_pcie_init();
+		kirkwood_pcie_init(KW_PCIE0);
 
 	return 0;
 }

arch/arm/mach-kirkwood/ts219-setup.c

@@ -74,8 +74,8 @@ static unsigned int qnap_ts219_mpp_config[] __initdata = {
 	MPP3_SPI_MISO,
 	MPP4_SATA1_ACTn,
 	MPP5_SATA0_ACTn,
-	MPP8_TW_SDA,
-	MPP9_TW_SCK,
+	MPP8_TW0_SDA,
+	MPP9_TW0_SCK,
 	MPP10_UART0_TXD,
 	MPP11_UART0_RXD,
 	MPP13_UART1_TXD,	/* PIC controller */
@@ -83,6 +83,7 @@ static unsigned int qnap_ts219_mpp_config[] __initdata = {
 	MPP15_GPIO,		/* USB Copy button */
 	MPP16_GPIO,		/* Reset button */
 	MPP36_GPIO,		/* RAM: 0: 256 MB, 1: 512 MB */
+	MPP44_GPIO,		/* Board ID: 0: TS-11x, 1: TS-21x */
 	0
 };
 
@@ -110,10 +111,10 @@ static void __init qnap_ts219_init(void)
 
 static int __init ts219_pci_init(void)
 {
-   if (machine_is_ts219())
-           kirkwood_pcie_init();
+	if (machine_is_ts219())
+		kirkwood_pcie_init(KW_PCIE0);
 
-   return 0;
+	return 0;
 }
 subsys_initcall(ts219_pci_init);
 

arch/arm/mach-lpc32xx/Makefile.boot

+   zreladdr-y	:= 0x80008000
+params_phys-y	:= 0x80000100
+initrd_phys-y	:= 0x82000000
+