Commit 7f7c8a61 authored by eric miao's avatar eric miao Committed by Russell King

[ARM] pxa: make MFP configuration processor independent

There are two reasons for making the MFP configuration to be processor
independent, i.e. removing the relationship of configuration bits with
actual MFPR register settings:

   1. power management sometimes requires the MFP to be configured
      differently when in run mode or in low power mode

   2. for future integration of pxa{25x,27x} GPIO configurations

The modifications include:

1. introducing of processor independent MFP configuration bits, as
   defined in [include/asm-arm/arch-pxa/mfp.h]:

	bit  0.. 9 - MFP Pin Number (1024 Pins Maximum)
	bit 10..12 - Alternate Function Selection
	bit 13..15 - Drive Strength
	bit 16..18 - Low Power Mode State
	bit 19..20 - Low Power Mode Edge Detection
	bit 21..22 - Run Mode Pull State
	and so on,

2. moving the processor dependent code from mfp.h into mfp-pxa3xx.h

3. cleaning up of the MFPR bit definitions

4. mapping of processor independent MFP configuration into processor
   specific MFPR register settings is now totally encapsulated within
   pxa3xx_mfp_config()

5. using of "unsigned long" instead of invented type of "mfp_cfg_t"
   according to Documentation/CodingStyle Chapter 5, usage of this
   in platform code will be slowly removed in later patches
Signed-off-by: default avatareric miao <eric.miao@marvell.com>
Signed-off-by: default avatarRussell King <rmk+kernel@arm.linux.org.uk>
parent 0ad1fbc8
......@@ -20,6 +20,7 @@
#include <asm/hardware.h>
#include <asm/arch/mfp.h>
#include <asm/arch/mfp-pxa3xx.h>
/* mfp_spin_lock is used to ensure that MFP register configuration
* (most likely a read-modify-write operation) is atomic, and that
......@@ -28,43 +29,105 @@
static DEFINE_SPINLOCK(mfp_spin_lock);
static void __iomem *mfpr_mmio_base = (void __iomem *)&__REG(MFPR_BASE);
struct pxa3xx_mfp_pin {
unsigned long config; /* -1 for not configured */
unsigned long mfpr_off; /* MFPRxx Register offset */
unsigned long mfpr_run; /* Run-Mode Register Value */
unsigned long mfpr_lpm; /* Low Power Mode Register Value */
};
static struct pxa3xx_mfp_pin mfp_table[MFP_PIN_MAX];
/* mapping of MFP_LPM_* definitions to MFPR_LPM_* register bits */
const static unsigned long mfpr_lpm[] = {
MFPR_LPM_INPUT,
MFPR_LPM_DRIVE_LOW,
MFPR_LPM_DRIVE_HIGH,
MFPR_LPM_PULL_LOW,
MFPR_LPM_PULL_HIGH,
MFPR_LPM_FLOAT,
};
/* mapping of MFP_PULL_* definitions to MFPR_PULL_* register bits */
const static unsigned long mfpr_pull[] = {
MFPR_PULL_NONE,
MFPR_PULL_LOW,
MFPR_PULL_HIGH,
MFPR_PULL_BOTH,
};
/* mapping of MFP_LPM_EDGE_* definitions to MFPR_EDGE_* register bits */
const static unsigned long mfpr_edge[] = {
MFPR_EDGE_NONE,
MFPR_EDGE_RISE,
MFPR_EDGE_FALL,
MFPR_EDGE_BOTH,
};
#define mfpr_readl(off) \
__raw_readl(mfpr_mmio_base + (off))
#define mfpr_writel(off, val) \
__raw_writel(val, mfpr_mmio_base + (off))
#define mfp_configured(p) ((p)->config != -1)
/*
* perform a read-back of any MFPR register to make sure the
* previous writings are finished
*/
#define mfpr_sync() (void)__raw_readl(mfpr_mmio_base + 0)
static inline void __mfp_config(int pin, unsigned long val)
static inline void __mfp_config_run(struct pxa3xx_mfp_pin *p)
{
unsigned long off = mfp_table[pin].mfpr_off;
if (mfp_configured(p))
mfpr_writel(p->mfpr_off, p->mfpr_run);
}
mfp_table[pin].mfpr_val = val;
mfpr_writel(off, val);
static inline void __mfp_config_lpm(struct pxa3xx_mfp_pin *p)
{
if (mfp_configured(p) && p->mfpr_lpm != p->mfpr_run)
mfpr_writel(p->mfpr_off, p->mfpr_lpm);
}
void pxa3xx_mfp_config(mfp_cfg_t *mfp_cfgs, int num)
void pxa3xx_mfp_config(unsigned long *mfp_cfgs, int num)
{
int i, pin;
unsigned long val, flags;
mfp_cfg_t *mfp_cfg = mfp_cfgs;
unsigned long flags;
int i;
spin_lock_irqsave(&mfp_spin_lock, flags);
for (i = 0; i < num; i++, mfp_cfg++) {
pin = MFP_CFG_PIN(*mfp_cfg);
val = MFP_CFG_VAL(*mfp_cfg);
for (i = 0; i < num; i++, mfp_cfgs++) {
unsigned long tmp, c = *mfp_cfgs;
struct pxa3xx_mfp_pin *p;
int pin, af, drv, lpm, edge, pull;
pin = MFP_PIN(c);
BUG_ON(pin >= MFP_PIN_MAX);
__mfp_config(pin, val);
p = &mfp_table[pin];
af = MFP_AF(c);
drv = MFP_DS(c);
lpm = MFP_LPM_STATE(c);
edge = MFP_LPM_EDGE(c);
pull = MFP_PULL(c);
/* run-mode pull settings will conflict with MFPR bits of
* low power mode state, calculate mfpr_run and mfpr_lpm
* individually if pull != MFP_PULL_NONE
*/
tmp = MFPR_AF_SEL(af) | MFPR_DRIVE(drv);
if (likely(pull == MFP_PULL_NONE)) {
p->mfpr_run = tmp | mfpr_lpm[lpm] | mfpr_edge[edge];
p->mfpr_lpm = p->mfpr_run;
} else {
p->mfpr_lpm = tmp | mfpr_lpm[lpm] | mfpr_edge[edge];
p->mfpr_run = tmp | mfpr_pull[pull];
}
p->config = c; __mfp_config_run(p);
}
mfpr_sync();
......@@ -110,7 +173,8 @@ void __init pxa3xx_mfp_init_addr(struct pxa3xx_mfp_addr_map *map)
do {
mfp_table[i].mfpr_off = offset;
mfp_table[i].mfpr_val = 0;
mfp_table[i].mfpr_run = 0;
mfp_table[i].mfpr_lpm = 0;
offset += 4; i++;
} while ((i <= p->end) && (p->end != -1));
}
......@@ -120,5 +184,8 @@ void __init pxa3xx_mfp_init_addr(struct pxa3xx_mfp_addr_map *map)
void __init pxa3xx_init_mfp(void)
{
memset(mfp_table, 0, sizeof(mfp_table));
int i;
for (i = 0; i < ARRAY_SIZE(mfp_table); i++)
mfp_table[i].config = -1;
}
#ifndef __ASM_ARCH_MFP_PXA3XX_H
#define __ASM_ARCH_MFP_PXA3XX_H
#define MFPR_BASE (0x40e10000)
#define MFPR_SIZE (PAGE_SIZE)
/* MFPR register bit definitions */
#define MFPR_PULL_SEL (0x1 << 15)
#define MFPR_PULLUP_EN (0x1 << 14)
#define MFPR_PULLDOWN_EN (0x1 << 13)
#define MFPR_SLEEP_SEL (0x1 << 9)
#define MFPR_SLEEP_OE_N (0x1 << 7)
#define MFPR_EDGE_CLEAR (0x1 << 6)
#define MFPR_EDGE_FALL_EN (0x1 << 5)
#define MFPR_EDGE_RISE_EN (0x1 << 4)
#define MFPR_SLEEP_DATA(x) ((x) << 8)
#define MFPR_DRIVE(x) (((x) & 0x7) << 10)
#define MFPR_AF_SEL(x) (((x) & 0x7) << 0)
#define MFPR_EDGE_NONE (0)
#define MFPR_EDGE_RISE (MFPR_EDGE_RISE_EN)
#define MFPR_EDGE_FALL (MFPR_EDGE_FALL_EN)
#define MFPR_EDGE_BOTH (MFPR_EDGE_RISE | MFPR_EDGE_FALL)
/*
* Table that determines the low power modes outputs, with actual settings
* used in parentheses for don't-care values. Except for the float output,
* the configured driven and pulled levels match, so if there is a need for
* non-LPM pulled output, the same configuration could probably be used.
*
* Output value sleep_oe_n sleep_data pullup_en pulldown_en pull_sel
* (bit 7) (bit 8) (bit 14) (bit 13) (bit 15)
*
* Input 0 X(0) X(0) X(0) 0
* Drive 0 0 0 0 X(1) 0
* Drive 1 0 1 X(1) 0 0
* Pull hi (1) 1 X(1) 1 0 0
* Pull lo (0) 1 X(0) 0 1 0
* Z (float) 1 X(0) 0 0 0
*/
#define MFPR_LPM_INPUT (0)
#define MFPR_LPM_DRIVE_LOW (MFPR_SLEEP_DATA(0) | MFPR_PULLDOWN_EN)
#define MFPR_LPM_DRIVE_HIGH (MFPR_SLEEP_DATA(1) | MFPR_PULLUP_EN)
#define MFPR_LPM_PULL_LOW (MFPR_LPM_DRIVE_LOW | MFPR_SLEEP_OE_N)
#define MFPR_LPM_PULL_HIGH (MFPR_LPM_DRIVE_HIGH | MFPR_SLEEP_OE_N)
#define MFPR_LPM_FLOAT (MFPR_SLEEP_OE_N)
#define MFPR_LPM_MASK (0xe080)
/*
* The pullup and pulldown state of the MFP pin at run mode is by default
* determined by the selected alternate function. In case that some buggy
* devices need to override this default behavior, the definitions below
* indicates the setting of corresponding MFPR bits
*
* Definition pull_sel pullup_en pulldown_en
* MFPR_PULL_NONE 0 0 0
* MFPR_PULL_LOW 1 0 1
* MFPR_PULL_HIGH 1 1 0
* MFPR_PULL_BOTH 1 1 1
*/
#define MFPR_PULL_NONE (0)
#define MFPR_PULL_LOW (MFPR_PULL_SEL | MFPR_PULLDOWN_EN)
#define MFPR_PULL_BOTH (MFPR_PULL_LOW | MFPR_PULLUP_EN)
#define MFPR_PULL_HIGH (MFPR_PULL_SEL | MFPR_PULLUP_EN)
/* PXA3xx common MFP configurations - processor specific ones defined
* in mfp-pxa300.h and mfp-pxa320.h
*/
......@@ -134,4 +197,56 @@
#define GPIO5_2_GPIO MFP_CFG(GPIO5_2, AF0)
#define GPIO6_2_GPIO MFP_CFG(GPIO6_2, AF0)
/*
* each MFP pin will have a MFPR register, since the offset of the
* register varies between processors, the processor specific code
* should initialize the pin offsets by pxa3xx_mfp_init_addr()
*
* pxa3xx_mfp_init_addr - accepts a table of "pxa3xx_mfp_addr_map"
* structure, which represents a range of MFP pins from "start" to
* "end", with the offset begining at "offset", to define a single
* pin, let "end" = -1
*
* use
*
* MFP_ADDR_X() to define a range of pins
* MFP_ADDR() to define a single pin
* MFP_ADDR_END to signal the end of pin offset definitions
*/
struct pxa3xx_mfp_addr_map {
unsigned int start;
unsigned int end;
unsigned long offset;
};
#define MFP_ADDR_X(start, end, offset) \
{ MFP_PIN_##start, MFP_PIN_##end, offset }
#define MFP_ADDR(pin, offset) \
{ MFP_PIN_##pin, -1, offset }
#define MFP_ADDR_END { MFP_PIN_INVALID, 0 }
/*
* pxa3xx_mfp_read()/pxa3xx_mfp_write() - for direct read/write access
* to the MFPR register
*/
unsigned long pxa3xx_mfp_read(int mfp);
void pxa3xx_mfp_write(int mfp, unsigned long mfpr_val);
/*
* pxa3xx_mfp_config - configure the MFPR registers
*
* used by board specific initialization code
*/
void pxa3xx_mfp_config(unsigned long *mfp_cfgs, int num);
/*
* pxa3xx_mfp_init_addr() - initialize the mapping between mfp pin
* index and MFPR register offset
*
* used by processor specific code
*/
void __init pxa3xx_mfp_init_addr(struct pxa3xx_mfp_addr_map *);
void __init pxa3xx_init_mfp(void);
#endif /* __ASM_ARCH_MFP_PXA3XX_H */
......@@ -16,9 +16,6 @@
#ifndef __ASM_ARCH_MFP_H
#define __ASM_ARCH_MFP_H
#define MFPR_BASE (0x40e10000)
#define MFPR_SIZE (PAGE_SIZE)
#define mfp_to_gpio(m) ((m) % 128)
/* list of all the configurable MFP pins */
......@@ -216,115 +213,22 @@ enum {
MFP_PIN_MAX,
};
/*
* Table that determines the low power modes outputs, with actual settings
* used in parentheses for don't-care values. Except for the float output,
* the configured driven and pulled levels match, so if there is a need for
* non-LPM pulled output, the same configuration could probably be used.
*
* Output value sleep_oe_n sleep_data pullup_en pulldown_en pull_sel
* (bit 7) (bit 8) (bit 14d) (bit 13d)
*
* Drive 0 0 0 0 X (1) 0
* Drive 1 0 1 X (1) 0 0
* Pull hi (1) 1 X(1) 1 0 0
* Pull lo (0) 1 X(0) 0 1 0
* Z (float) 1 X(0) 0 0 0
*/
#define MFP_LPM_DRIVE_LOW 0x8
#define MFP_LPM_DRIVE_HIGH 0x6
#define MFP_LPM_PULL_HIGH 0x7
#define MFP_LPM_PULL_LOW 0x9
#define MFP_LPM_FLOAT 0x1
#define MFP_LPM_PULL_NEITHER 0x0
/*
* The pullup and pulldown state of the MFP pin is by default determined by
* selected alternate function. In case some buggy devices need to override
* this default behavior, pxa3xx_mfp_set_pull() can be invoked with one of
* the following definition as the parameter.
*
* Definition pull_sel pullup_en pulldown_en
* MFP_PULL_HIGH 1 1 0
* MFP_PULL_LOW 1 0 1
* MFP_PULL_BOTH 1 1 1
* MFP_PULL_NONE 1 0 0
* MFP_PULL_DEFAULT 0 X X
*
* NOTE: pxa3xx_mfp_set_pull() will modify the PULLUP_EN and PULLDOWN_EN
* bits, which will cause potential conflicts with the low power mode
* setting, device drivers should take care of this
*/
#define MFP_PULL_BOTH (0x7u)
#define MFP_PULL_HIGH (0x6u)
#define MFP_PULL_LOW (0x5u)
#define MFP_PULL_NONE (0x4u)
#define MFP_PULL_DEFAULT (0x0u)
#define MFP_AF0 (0)
#define MFP_AF1 (1)
#define MFP_AF2 (2)
#define MFP_AF3 (3)
#define MFP_AF4 (4)
#define MFP_AF5 (5)
#define MFP_AF6 (6)
#define MFP_AF7 (7)
#define MFP_DS01X (0)
#define MFP_DS02X (1)
#define MFP_DS03X (2)
#define MFP_DS04X (3)
#define MFP_DS06X (4)
#define MFP_DS08X (5)
#define MFP_DS10X (6)
#define MFP_DS12X (7)
#define MFP_EDGE_BOTH 0x3
#define MFP_EDGE_RISE 0x2
#define MFP_EDGE_FALL 0x1
#define MFP_EDGE_NONE 0x0
#define MFPR_AF_MASK 0x0007
#define MFPR_DRV_MASK 0x1c00
#define MFPR_RDH_MASK 0x0200
#define MFPR_LPM_MASK 0xe180
#define MFPR_PULL_MASK 0xe000
#define MFPR_EDGE_MASK 0x0070
#define MFPR_ALT_OFFSET 0
#define MFPR_ERE_OFFSET 4
#define MFPR_EFE_OFFSET 5
#define MFPR_EC_OFFSET 6
#define MFPR_SON_OFFSET 7
#define MFPR_SD_OFFSET 8
#define MFPR_SS_OFFSET 9
#define MFPR_DRV_OFFSET 10
#define MFPR_PD_OFFSET 13
#define MFPR_PU_OFFSET 14
#define MFPR_PS_OFFSET 15
#define MFPR(af, drv, rdh, lpm, edge) \
(((af) & 0x7) | (((drv) & 0x7) << 10) |\
(((rdh) & 0x1) << 9) |\
(((lpm) & 0x3) << 7) |\
(((lpm) & 0x4) << 12)|\
(((lpm) & 0x8) << 10)|\
((!(edge)) << 6) |\
(((edge) & 0x1) << 5) |\
(((edge) & 0x2) << 3))
/*
* a possible MFP configuration is represented by a 32-bit integer
* bit 0..15 - MFPR value (16-bit)
* bit 16..31 - mfp pin index (used to obtain the MFPR offset)
*
* bit 0.. 9 - MFP Pin Number (1024 Pins Maximum)
* bit 10..12 - Alternate Function Selection
* bit 13..15 - Drive Strength
* bit 16..18 - Low Power Mode State
* bit 19..20 - Low Power Mode Edge Detection
* bit 21..22 - Run Mode Pull State
*
* to facilitate the definition, the following macros are provided
*
* MFPR_DEFAULT - default MFPR value, with
* MFP_CFG_DEFAULT - default MFP configuration value, with
* alternate function = 0,
* drive strength = fast 1mA (MFP_DS01X)
* drive strength = fast 3mA (MFP_DS03X)
* low power mode = default
* release dalay hold = false (RDH bit)
* edge detection = none
*
* MFP_CFG - default MFPR value with alternate function
......@@ -334,104 +238,74 @@ enum {
* low power mode
* MFP_CFG_X - default MFPR value with alternate function,
* pin drive strength and low power mode
*
* use
*
* MFP_CFG_PIN - to get the MFP pin index
* MFP_CFG_VAL - to get the corresponding MFPR value
*/
typedef uint32_t mfp_cfg_t;
#define MFP_CFG_PIN(mfp_cfg) (((mfp_cfg) >> 16) & 0xffff)
#define MFP_CFG_VAL(mfp_cfg) ((mfp_cfg) & 0xffff)
/*
* MFP register defaults to
* drive strength fast 3mA (010'b)
* edge detection logic disabled
* alternate function 0
*/
#define MFPR_DEFAULT (0x0840)
typedef unsigned long mfp_cfg_t;
#define MFP_PIN(x) ((x) & 0x3ff)
#define MFP_AF0 (0x0 << 10)
#define MFP_AF1 (0x1 << 10)
#define MFP_AF2 (0x2 << 10)
#define MFP_AF3 (0x3 << 10)
#define MFP_AF4 (0x4 << 10)
#define MFP_AF5 (0x5 << 10)
#define MFP_AF6 (0x6 << 10)
#define MFP_AF7 (0x7 << 10)
#define MFP_AF_MASK (0x7 << 10)
#define MFP_AF(x) (((x) >> 10) & 0x7)
#define MFP_DS01X (0x0 << 13)
#define MFP_DS02X (0x1 << 13)
#define MFP_DS03X (0x2 << 13)
#define MFP_DS04X (0x3 << 13)
#define MFP_DS06X (0x4 << 13)
#define MFP_DS08X (0x5 << 13)
#define MFP_DS10X (0x6 << 13)
#define MFP_DS13X (0x7 << 13)
#define MFP_DS_MASK (0x7 << 13)
#define MFP_DS(x) (((x) >> 13) & 0x7)
#define MFP_LPM_INPUT (0x0 << 16)
#define MFP_LPM_DRIVE_LOW (0x1 << 16)
#define MFP_LPM_DRIVE_HIGH (0x2 << 16)
#define MFP_LPM_PULL_LOW (0x3 << 16)
#define MFP_LPM_PULL_HIGH (0x4 << 16)
#define MFP_LPM_FLOAT (0x5 << 16)
#define MFP_LPM_STATE_MASK (0x7 << 16)
#define MFP_LPM_STATE(x) (((x) >> 16) & 0x7)
#define MFP_LPM_EDGE_NONE (0x0 << 19)
#define MFP_LPM_EDGE_RISE (0x1 << 19)
#define MFP_LPM_EDGE_FALL (0x2 << 19)
#define MFP_LPM_EDGE_BOTH (0x3 << 19)
#define MFP_LPM_EDGE_MASK (0x3 << 19)
#define MFP_LPM_EDGE(x) (((x) >> 19) & 0x3)
#define MFP_PULL_NONE (0x0 << 21)
#define MFP_PULL_LOW (0x1 << 21)
#define MFP_PULL_HIGH (0x2 << 21)
#define MFP_PULL_BOTH (0x3 << 21)
#define MFP_PULL_MASK (0x3 << 21)
#define MFP_PULL(x) (((x) >> 21) & 0x3)
#define MFP_CFG_DEFAULT (MFP_AF0 | MFP_DS03X | MFP_LPM_INPUT |\
MFP_LPM_EDGE_NONE | MFP_PULL_NONE)
#define MFP_CFG(pin, af) \
((MFP_PIN_##pin << 16) | MFPR_DEFAULT | (MFP_##af))
((MFP_CFG_DEFAULT & ~MFP_AF_MASK) |\
(MFP_PIN(MFP_PIN_##pin) | MFP_##af))
#define MFP_CFG_DRV(pin, af, drv) \
((MFP_PIN_##pin << 16) | (MFPR_DEFAULT & ~MFPR_DRV_MASK) |\
((MFP_##drv) << 10) | (MFP_##af))
((MFP_CFG_DEFAULT & ~(MFP_AF_MASK | MFP_DS_MASK)) |\
(MFP_PIN(MFP_PIN_##pin) | MFP_##af | MFP_##drv))
#define MFP_CFG_LPM(pin, af, lpm) \
((MFP_PIN_##pin << 16) | (MFPR_DEFAULT & ~MFPR_LPM_MASK) |\
(((MFP_LPM_##lpm) & 0x3) << 7) |\
(((MFP_LPM_##lpm) & 0x4) << 12) |\
(((MFP_LPM_##lpm) & 0x8) << 10) |\
(MFP_##af))
((MFP_CFG_DEFAULT & ~(MFP_AF_MASK | MFP_LPM_STATE_MASK)) |\
(MFP_PIN(MFP_PIN_##pin) | MFP_##af | MFP_LPM_##lpm))
#define MFP_CFG_X(pin, af, drv, lpm) \
((MFP_PIN_##pin << 16) |\
(MFPR_DEFAULT & ~(MFPR_DRV_MASK | MFPR_LPM_MASK)) |\
((MFP_##drv) << 10) | (MFP_##af) |\
(((MFP_LPM_##lpm) & 0x3) << 7) |\
(((MFP_LPM_##lpm) & 0x4) << 12) |\
(((MFP_LPM_##lpm) & 0x8) << 10))
/*
* each MFP pin will have a MFPR register, since the offset of the
* register varies between processors, the processor specific code
* should initialize the pin offsets by pxa3xx_mfp_init_addr()
*
* pxa3xx_mfp_init_addr - accepts a table of "pxa3xx_mfp_addr_map"
* structure, which represents a range of MFP pins from "start" to
* "end", with the offset begining at "offset", to define a single
* pin, let "end" = -1
*
* use
*
* MFP_ADDR_X() to define a range of pins
* MFP_ADDR() to define a single pin
* MFP_ADDR_END to signal the end of pin offset definitions
*/
struct pxa3xx_mfp_addr_map {
unsigned int start;
unsigned int end;
unsigned long offset;
};
#define MFP_ADDR_X(start, end, offset) \
{ MFP_PIN_##start, MFP_PIN_##end, offset }
#define MFP_ADDR(pin, offset) \
{ MFP_PIN_##pin, -1, offset }
#define MFP_ADDR_END { MFP_PIN_INVALID, 0 }
struct pxa3xx_mfp_pin {
unsigned long mfpr_off; /* MFPRxx register offset */
unsigned long mfpr_val; /* MFPRxx register value */
};
/*
* pxa3xx_mfp_read()/pxa3xx_mfp_write() - for direct read/write access
* to the MFPR register
*/
unsigned long pxa3xx_mfp_read(int mfp);
void pxa3xx_mfp_write(int mfp, unsigned long mfpr_val);
/*
* pxa3xx_mfp_config - configure the MFPR registers
*
* used by board specific initialization code
*/
void pxa3xx_mfp_config(mfp_cfg_t *mfp_cfgs, int num);
/*
* pxa3xx_mfp_init_addr() - initialize the mapping between mfp pin
* index and MFPR register offset
*
* used by processor specific code
*/
void __init pxa3xx_mfp_init_addr(struct pxa3xx_mfp_addr_map *);
void __init pxa3xx_init_mfp(void);
((MFP_CFG_DEFAULT & ~(MFP_AF_MASK | MFP_DS_MASK | MFP_LPM_STATE_MASK)) |\
(MFP_PIN(MFP_PIN_##pin) | MFP_##af | MFP_##drv | MFP_LPM_##lpm))
#endif /* __ASM_ARCH_MFP_H */
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment