The new-style lm78 driver implements the optional detect() callback
to cover the use cases of the legacy driver.
Signed-off-by: Jean Delvare <khali@linux-fr.org>

Upcoming changes to the I2C part of the lm78 driver will cause ISA
devices to no longer have a struct i2c_client at hand. So, we must
stop (ab)using it now.
Signed-off-by: Jean Delvare <khali@linux-fr.org>

The LM78 detection is relatively weak, and sometimes recent Winbond
chips can be misdetected as an LM78. We have had repeated reports of
this happening. We have an explicit check against this for the ISA
access, do the same for I2C access now.
Signed-off-by: Jean Delvare <khali@linux-fr.org>

The LM78 and LM79 can be accessed either on the I2C bus or the ISA
bus. We must not access the same chip through both interfaces. So far
we were relying on the user passing the correct ignore parameter to
skip the registration of the I2C interface as suggested by
sensors-detect, but this is fragile: the user may load the lm78
driver without running sensors-detect, and the i2c bus numbers are
not stable across reboots and hardware changes.

So, better detect alias chips in the driver directly, and skip any
I2C chip which is obviously an alias of the ISA chip. This is done
by comparing the value of 26 selected registers.
Signed-off-by: Jean Delvare <khali@linux-fr.org>

Only request I/O ports 0x295-0x296 instead of the full I/O address
range. This solves a conflict with PNP resources on a few motherboards.

Also request the I/O ports in two parts (4 low ports, 4 high ports)
during device detection, otherwise the PNP resource make the request
(and thus the detection) fail.

This is the exact same fix that was applied to driver w83781d in
March 2008 to address the same problem:
http://git.kernel.org/?p=linux/kernel/git/torvalds/linux-2.6.git;a=commit;h=2961cb22ef02850d90e7a12c28a14d74e327df8dSigned-off-by: Jean Delvare <khali@linux-fr.org>

Label names ERROR1 and ERROR3 aren't exactly explicit. Change them for
better names that indicate what we are up to.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Herbert Poetzl <herbert@13thfloor.at>

Function RANGE_TO_REG can easily be simplified. Credits go to Herbert
Poetzl for indirectly suggesting this to me. I tested that the new
implementation returns the same result as the original implementation
for all input values.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Herbert Poetzl <herbert@13thfloor.at>

The new-style lm85 driver implements the optional detect() callback
to cover the use cases of the legacy driver.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Herbert Poetzl <herbert@13thfloor.at>

The Analog Devices and SMSC devices supported by the lm85 driver do
not have the same PWM frequency table as the National Semiconductor
devices. Add support for per-device frequency tables.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Herbert Poetzl <herbert@13thfloor.at>

The LM85 and compatible chips only support 8 arbitrary PWM frequencies.
The algorithm to pick one of them based on the user input is not
optimum. Improve it to always pick the closest supported frequency.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Herbert Poetzl <herbert@13thfloor.at>

Implement the standard PWM frequency interface: pwm[1-*]_freq in
units of 1 Hz, instead of the non-standard pwm[1-*]_auto_pwm_freq
in units of 0.1 Hz. The old naming was not only non-standard, it was
also confusing, because it suggested that the frequency value only
applied in automatic fan speed mode, which isn't true.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Herbert Poetzl <herbert@13thfloor.at>

Rework the device detection to make it clearer and faster in the
general case (when a known device is found.)
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Herbert Poetzl <herbert@13thfloor.at>

Simplify the IRQ handling routine of ams driver.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Jean Delvare <khali@linux-fr.org>

Use a separate mutex to serialize input device creation/removal,
otheriwse we deadlock if we try to remove input device while it is
being polled. Also do not take ams_info.lock when it is not needed.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Jean Delvare <khali@linux-fr.org>

We should not allow writes to the 'joystick' module parameters since
writing there will not trigger creation of the input device. Disable
writes since we provide alternative way of enabling input device via
AMS device's sysfs attribute.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Jean Delvare <khali@linux-fr.org>

The legacy i2c binding model is phasing out, so the ams driver needs
to be converted to a new-style i2c driver. Here is a naive approach of
this conversion. Basically it is moving the i2c device creation from
the ams driver to the i2c-powermac driver. This should work, but I
suspect we could come up with something cleaner by declaring the i2c
device as part of the platform setup. This could be done later by
someone more familiar with openfirmware-based platforms than I am
myself.

One nice thing brought by this conversion is that the ams driver
should be loaded automatically on systems where is is needed (at
least when the I2C interface to the chip is used) providing
coldplug-aware user-space environment.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Cc: Stelian Pop <stelian@popies.net>
Cc: Michael Hanselmann <linux-kernel@hansmi.ch>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>

The lm87 driver normally assumes that firmware configured the chip
correctly.  Since this is not always the case, alllow platform code to
set the channel register value via platform_data.  All other
configuration registers can be changed after driver initialisation.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>

This means that if we have to start the monitor when probed, we also
stop it on removal.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>

lm87_init_client() conditionally sets the Start bit and clears the
INT#_Clear bit in the Config 1 register.  The condition should be that
either of these bits needs changing, but currently it checks the
(self-clearing) Initialization bit instead of INT#_Clear.

Fix the condition and also ensure we never set the Initialization bit.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>

Degrade the "Unsupported chip" message from info to debug level.
There's nothing wrong with this, so no need to bother the user.
Also make the message slightly more descriptive.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Martyn Welch <martyn.welch@gefanuc.com>

These Maxim chips are similar to MAX6657 but use unsigned temperature
values to allow for readings up to 145 degrees.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>

The encoding of temperatures varies between chips and modes.  So do not
use "temp1" or "temp2" in the names of the conversion functions, but
specify the encoding.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Tested-by: Martyn Welch <martyn.welch@gefanuc.com>

Support ADT7461 in extended temperature range mode, which will change
the range of readings from 0..127 to -64..191 degC.  Adjust the
register conversion functions accordingly.
Signed-off-by: Nate Case <ncase@xes-inc.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Tested-by: Martyn Welch <martyn.welch@gefanuc.com>

Use static functions instead of the TEMPx_FROM_REG* and TEMPx_TO_REG*
macros.  This will ensure type safety and eliminate any side effects
from arguments passed in since the macros referenced 'val' multiple
times.  This change should not affect functionality.
Signed-off-by: Nate Case <ncase@xes-inc.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Tested-by: Martyn Welch <martyn.welch@gefanuc.com>

Update the links to the datasheet of some of the devices supported by
the lm90 driver. Also remove the links from the driver itself, so that
we don't have to update them twice each time they change.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Martyn Welch <martyn.welch@gefanuc.com>

The Maxim chips supported by the lm90 driver have 8-bit high and low
remote limit values, not 11-bit as the other chips have. So stop reading
from and writing to registers that do not exist on these chips. Also
round the limit values set by the user properly.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Martyn Welch <martyn.welch@gefanuc.com>

The Maxim MAX6657, MAX6658 and MAX6659 have extra resolution bits for
the local temperature measurement. Let the lm90 driver read them and
export them to user-space.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Martyn Welch <martyn.welch@gefanuc.com>

Move the code which aggregates two 8-bit register values into a 16-bit
value to a separate function. We'll need to do it a second time soon and
I don't want to duplicate the code.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Martyn Welch <martyn.welch@gefanuc.com>

I dunno how this missed Bjorn and his quest to use %pF in commit
c80cfb04 ("vsprintf: use new vsprintf
symbolic function pointer format"), but it did.

So use %pF in the two remaining places that still tried to print out
function pointers by hand.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

* git://git.linux-nfs.org/projects/trondmy/nfs-2.6: (53 commits)
  NFS: Fix a resolution problem with nfs_inode->cache_change_attribute
  NFS: Fix the resolution problem with nfs_inode_attrs_need_update()
  NFS: Changes to inode->i_nlinks must set the NFS_INO_INVALID_ATTR flag
  RPC/RDMA: ensure connection attempt is complete before signalling.
  RPC/RDMA: correct the reconnect timer backoff
  RPC/RDMA: optionally emit useful transport info upon connect/disconnect.
  RPC/RDMA: reformat a debug printk to keep lines together.
  RPC/RDMA: harden connection logic against missing/late rdma_cm upcalls.
  RPC/RDMA: fix connect/reconnect resource leak.
  RPC/RDMA: return a consistent error, when connect fails.
  RPC/RDMA: adhere to protocol for unpadded client trailing write chunks.
  RPC/RDMA: avoid an oops due to disconnect racing with async upcalls.
  RPC/RDMA: maintain the RPC task bytes-sent statistic.
  RPC/RDMA: suppress retransmit on RPC/RDMA clients.
  RPC/RDMA: fix connection IRD/ORD setting
  RPC/RDMA: support FRMR client memory registration.
  RPC/RDMA: check selected memory registration mode at runtime.
  RPC/RDMA: add data types and new FRMR memory registration enum.
  RPC/RDMA: refactor the inline memory registration code.
  NFS: fix nfs_parse_ip_address() corner case
  ...

Merge branch 'sched-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip

* 'sched-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
  sched_clock: prevent scd->clock from moving backwards

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6:
  ALSA: us122l: fix missing unlock in usb_stream_hwdep_vm_fault()
  ALSA: hda - Fix quirk lists for realtek codecs
  ALSA: hda - Add support of ALC272
  ALSA: hda - Add ALC887 support
  ALSA: hda - Add ALC1200 support
  ALSA: hda - Fix PCI SSID of ASUS M90V
  ALSA: hda - Add auto mic switch in realtek auto-probe mode
  ALSA: Fix pxa2xx-ac97-lib.c compilation
  ALSA: ASoC: Hide TLV320AIC26 configuration option for non-OpenFirwmare users
  ALSA: hda: fix nid variable warning
  ALSA: ASoC: Fix compile-time warning for tlv320aic23.c

* 'kvm-updates/2.6.28' of git://git.kernel.org/pub/scm/linux/kernel/git/avi/kvm: (134 commits)
  KVM: ia64: Add intel iommu support for guests.
  KVM: ia64: add directed mmio range support for kvm guests
  KVM: ia64: Make pmt table be able to hold physical mmio entries.
  KVM: Move irqchip_in_kernel() from ioapic.h to irq.h
  KVM: Separate irq ack notification out of arch/x86/kvm/irq.c
  KVM: Change is_mmio_pfn to kvm_is_mmio_pfn, and make it common for all archs
  KVM: Move device assignment logic to common code
  KVM: Device Assignment: Move vtd.c from arch/x86/kvm/ to virt/kvm/
  KVM: VMX: enable invlpg exiting if EPT is disabled
  KVM: x86: Silence various LAPIC-related host kernel messages
  KVM: Device Assignment: Map mmio pages into VT-d page table
  KVM: PIC: enhance IPI avoidance
  KVM: MMU: add "oos_shadow" parameter to disable oos
  KVM: MMU: speed up mmu_unsync_walk
  KVM: MMU: out of sync shadow core
  KVM: MMU: mmu_convert_notrap helper
  KVM: MMU: awareness of new kvm_mmu_zap_page behaviour
  KVM: MMU: mmu_parent_walk
  KVM: x86: trap invlpg
  KVM: MMU: sync roots on mmu reload
  ...

This fixes the broken 77af7e34
("softirq, warning fix: correct a format to avoid a warning") fix
correctly.

The type of a pointer subtraction is not "int", nor is it "long".  It
can be either (or something else).  It's "ptrdiff_t", and the printk
format for it is "%td".

Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Merge branch 'core-v28-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip

* 'core-v28-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
  do_generic_file_read: s/EINTR/EIO/ if lock_page_killable() fails
  softirq, warning fix: correct a format to avoid a warning
  softirqs, debug: preemption check
  x86, pci-hotplug, calgary / rio: fix EBDA ioremap()
  IO resources, x86: ioremap sanity check to catch mapping requests exceeding, fix
  IO resources, x86: ioremap sanity check to catch mapping requests exceeding the BAR sizes
  softlockup: Documentation/sysctl/kernel.txt: fix softlockup_thresh description
  dmi scan: warn about too early calls to dmi_check_system()
  generic: redefine resource_size_t as phys_addr_t
  generic: make PFN_PHYS explicitly return phys_addr_t
  generic: add phys_addr_t for holding physical addresses
  softirq: allocate less vectors
  IO resources: fix/remove printk
  printk: robustify printk, update comment
  printk: robustify printk, fix #2
  printk: robustify printk, fix
  printk: robustify printk

Fixed up conflicts in:
	arch/powerpc/include/asm/types.h
	arch/powerpc/platforms/Kconfig.cputype
manually.

Merge branch 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip

* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
  x86: fix compat-vdso
  x86/mm: unify init task OOM handling
  x86/mm: do not trigger a kernel warning if user-space disables interrupts and generates a page fault

As noted by Akinobu Mita in patch b1fceac2,
alloc_bootmem and related functions never return NULL and always return a
zeroed region of memory.  Thus a NULL test or memset after calls to these
functions is unnecessary.

 arch/frv/mm/init.c |    2 --
 1 file changed, 2 deletions(-)

This was fixed using the following semantic patch.
(http://www.emn.fr/x-info/coccinelle/)

// <smpl>
@@
expression E;
statement S;
@@

E = \(alloc_bootmem\|alloc_bootmem_low\|alloc_bootmem_pages\|alloc_bootmem_low_pages\)(...)
... when != E
(
- BUG_ON (E == NULL);
|
- if (E == NULL) S
)

@@
expression E,E1;
@@

E = \(alloc_bootmem\|alloc_bootmem_low\|alloc_bootmem_pages\|alloc_bootmem_low_pages\)(...)
... when != E
- memset(E,0,E1);
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Switch unaligned access to the packed-struct implementation for BE accesses as
this reduces the size of the kernel a little.  LE still uses the byte shift.
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Provide dma_map_page() for the NOMMU-mode FRV arch.

Also do some fixing on the comments attached to the various DMA functions for
both MMU and NOMMU mode FRV code.
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Use the generic pci_enable_resources() instead of the arch-specific code.

Unlike this arch-specific code, the generic version:
    - checks PCI_NUM_RESOURCES (11), not 6, resources
    - skips resources that have neither IORESOURCE_IO nor IORESOURCE_MEM set
    - skips ROM resources unless IORESOURCE_ROM_ENABLE is set
    - checks for resource collisions with "!r->parent"
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>