Commits · 0cbfc065fe15a51e4f637888263ecf82057a6e00 · Kirill Smelkov / linux

03 Mar, 2015 34 commits

bcma: gpio: enable GPIO IRQ domain on BCM5301X · 0cbfc065

Rafał Miłecki authored Feb 20, 2015

Just like on BCM47XX arch, BCM5301X also has ChipCommon with IRQ for
GPIOs. Now we have interrupts working on BCM5301X we can finally make
use of it. This has been successfully tested on 5 different devices
(Buffalo, Luxul, Netgear).
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

0cbfc065

ssb: Silence warning for unknown backplane revision · 16f7031a

Larry Finger authored Feb 18, 2015

When using a BCM4318 in a PCMCIA format, I get a startup message that the
device uses backplane revision 0xF000000. Next a WARNING is logged. Despite
the message, the device works fine, This patch silences the warning.

Cc: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

16f7031a

wil6210: increase cmd buffer size to avoid sscanf buffer overflow · 2a19f776

Colin Ian King authored Mar 01, 2015

cppcheck detected a buffer overflow:

[drivers/net/wireless/ath/wil6210/debugfs.c:634]: (error) Width 8
  given in format string (no. 1) is larger than destination buffer
  'cmd[8]', use %7s to prevent overflowing it.

For the current %8s sscanf we require cmd to be 9 chars long
so increase it by 1 byte to prevent the sscan overflow (rather
than reduce the %8s specifier to %7s as cppcheck recommends).
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

2a19f776

ath9k: Fix issues in the main btcoex timer · 6e6dd08d

Sujith Manoharan authored Mar 01, 2015

* ath9k_mci_update_rssi() is required only for
  cards that use MCI scheme. Make sure that it
  is not called for 3-wire cards.

* Call ath9k_ps_wakeup() early since register
  accesses are made in ath9k_mci_update_rssi().

* Fix usage of btcoex_lock to handle no_stomp_timer.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

6e6dd08d

ath9k: Handle timers for MCI · c7266e99

Sujith Manoharan authored Mar 01, 2015

Make sure that the btcoex timers are started/stopped
properly for both 3-wire and MCI schemes.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

c7266e99

ath9k: Fix wlan-active gpio for the AR9003 family · 30b81898

Sujith Manoharan authored Mar 01, 2015

When disabling BTCOEX, clearing the wlanactive gpio line
is required only for pre-AR9003 cards.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

30b81898

ath9k: Fix MCI scheme initialization · e1ff147d

Sujith Manoharan authored Mar 01, 2015

Commit "ath9k_hw: remove ATH_BTCOEX_CFG_MCI" removed
MCI as a separate coex scheme, but we need it to
avoid fiddling with GPIO registers during
ath9k_init_btcoex() that are meant only for 3-wire
cards.

Cc: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

e1ff147d

ath9k: Initialize MCI state correctly · 510baea1

Sujith Manoharan authored Mar 01, 2015

The MCI configuration values are assigned
in ath9k_hw_btcoex_init_mci() which are used
by the MCI reset routine. When initializing
BTCOEX/MCI, ath_mci_setup() ends up using
uninitialized data. Fix this by setting up
the configuration parameters before issuing
a MCI reset.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

510baea1

ath9k: Remove useless return value check · 44b9b56e

Sujith Manoharan authored Mar 01, 2015

ath_init_btcoex_timer() always returns 0, so
checking for error conditions is not required.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

44b9b56e

rtlwifi: rtl8192cu: Add case in rtl92cu_get_hw_reg · 3f5fe236

Taehee Yoo authored Feb 26, 2015

Add HAL_DEF_WOWLAN case in rtl92cu_get_hw_reg
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

3f5fe236

mwifiex: do not initialize ext_scan in mwifiex_init_adapter · bf97bf22

Avinash Patil authored Feb 25, 2015

Features which are device specific are already updated in
interface specific initialization e.g. register_dev.
We should not initialize them in mwifiex_init_adapter();
else this would overwrite earlier settings.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

bf97bf22

rtlwifi: rtl8188ee: missing curly braces in handle_branch1() · 1114ce8f

Dan Carpenter authored Feb 25, 2015

From the indenting, it seems like the READ_NEXT_PAIR() was supposed to
be inside the while loop.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

1114ce8f

rtlwifi: rtl8821ae: Remove duplicate hex prefixes · df905570

Rasmus Villemoes authored Feb 23, 2015

The # flag in %X means print a 0X prefix. Remove the extra 0x prefix.
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

df905570

ath9k: add per-vif TX power capability to TX path · 97bf8615

Lorenzo Bianconi authored Feb 17, 2015

In order to add per-vif TX power capability cap per-packet TX power to vif
configured power if the latter is lower than per-rate TX power and mac80211
per-frame power. Use vif TX power if TPC has been disabled for current the
interface
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi83@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

97bf8615

ath9k: add per-vif TX power capability · 283dd119

Lorenzo Bianconi authored Feb 17, 2015

Configure the HW with highest TX power among all vif when HW TPC has been
enabled in order to add support to per-vif TX power capability. Use lowest
configured power among all interfaces when TPC is disabled
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi83@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

283dd119

rtlwifi: Remove unused RTL_SUPPORTED_CTRL_FILTER define · be1f8d31
Priit Laes authored Feb 16, 2015
```
Signed-off-by: Priit Laes <plaes@plaes.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
```
be1f8d31