- 17 Jan, 2023 9 commits
-
-
Manivannan Sadhasivam authored
SM8350 default init sequence sets some PCS registers to HS G3, thereby disabling HS G4 mode. This has the effect on MPHY capability negotiation between the host and the device during link startup and causes the PA_MAXHSGEAR to G3 irrespective of device max gear. Due to that, the agreed gear speed determined by the UFS core will become G3 only and the platform won't run at G4. So, let's remove setting these registers for SM8350 as like other G4 compatible platforms. One downside of this is that, when the board design uses non-G4 compatible device, then MPHY will continue to run in the default mode (G4) even if UFSHCD runs in G3. But this is the case for other platforms as well. Tested-by: Andrew Halaney <ahalaney@redhat.com> # Qdrive3/sa8540p-ride Signed-off-by:
Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org> Link: https://lore.kernel.org/r/20230114071009.88102-10-manivannan.sadhasivam@linaro.orgSigned-off-by:
Vinod Koul <vkoul@kernel.org>
-
Manivannan Sadhasivam authored
UFS PHY in SM8250 SoC is capable of operating at HS G4 mode. Hence, add the required register settings using the tables_hs_g4 struct instance. This also requires a separate qmp_phy_cfg for SM8250 instead of reusing SM8150. Reviewed-by:
Dmitry Baryshkov <dmitry.baryshkov@linaro.org> Tested-by: Andrew Halaney <ahalaney@redhat.com> # Qdrive3/sa8540p-ride Signed-off-by:
-
Manivannan Sadhasivam authored
UFS PHY in SM8150 SoC is capable of operating at HS G4 mode. Hence, add the required register settings using the tables_hs_g4 struct instance. Reviewed-by:
-
Manivannan Sadhasivam authored
Since now there is support for configuring the HS Rate B mode properly, let's move the register setting to tbls_hs_b struct for all SoCs. This allows the PHY to be configured in Rate A initially and then in Rate B if requested by the UFS driver. Reviewed-by:
-
Manivannan Sadhasivam authored
Add separate tables_hs_g4 instance to allow the PHY driver to configure the PHY in HS G4 mode. The individual SoC configs need to supply the Rx, Tx and PCS register setting in tables_hs_g4 and the UFS driver can request the Hs G4 mode by calling phy_set_mode_ext() with submode set to UFS_HS_G4. Reviewed-by:
-
Manivannan Sadhasivam authored
Add separate tables_hs_b instance to allow the PHY driver to configure the PHY in HS Series B mode. The individual SoC configs need to supply the serdes register setting in tables_hs_b and the UFS driver can request the Series B mode by calling phy_set_mode() with mode set to PHY_MODE_UFS_HS_B. Reviewed-by:
-
Manivannan Sadhasivam authored
As done for Qcom PCIe PHY driver, let's move the register settings to the common qmp_phy_cfg_tbls struct. This helps in adding any additional PHY settings needed for functionalities like HS-G4 in the future by adding one more instance of the qmp_phy_cfg_tbls. Reviewed-by:
-
Manivannan Sadhasivam authored
Only MSM8996 is using "_ufs_" naming convention for PHY definitions instead of "_ufsphy_" as like other SoCs. So to maintain the uniformity, let's rename all of the definitions to use "_ufsphy_". Reviewed-by:
-
Manivannan Sadhasivam authored
Following the other QMP PHY drivers like PCIe, let's remove the "_tbl" suffix from the qmp_phy_init_tbl definitions. This helps in maintaining the uniformity across all of the QMP PHY drivers. Reviewed-by:
-
- 13 Jan, 2023 14 commits
-
-
Neil Armstrong authored
Convert the Amlogic Meson GXL USB2 PHY bindings to dt-schema. Reviewed-by:
Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> Reviewed-by:
Martin Blumenstingl <martin.blumenstingl@googlemail.com> Signed-off-by:
Neil Armstrong <neil.armstrong@linaro.org> Link: https://lore.kernel.org/r/20221117-b4-amlogic-bindings-convert-v2-8-36ad050bb625@linaro.orgSigned-off-by:
-
Lux Aliaga authored
The SM6125 UFS PHY is compatible with the one from SM6115. Add a compatible for it and modify the config from SM6115 to make them compatible with the SC8280XP binding Signed-off-by:
Lux Aliaga <they@mint.lgbt> Reviewed-by:
Martin Botka <martin.botka@somainline.org> Link: https://lore.kernel.org/r/20230108195336.388349-4-they@mint.lgbtSigned-off-by:
-
Lux Aliaga authored
Document the QMP UFS PHY compatible for SM6125. Signed-off-by:
Dhruva Gole <d-gole@ti.com> Acked-by:
-
Krzysztof Kozlowski authored
Different variants of Qualcomm USB3 DP PHY take different clocks (according to upstream DTS and Linux driver): sc7280-herobrine-crd.dtb: phy-wrapper@88e9000: clocks: [[43, 151], [39, 0], [43, 153]] is too short sc7280-herobrine-crd.dtb: phy-wrapper@88e9000: clock-names:1: 'cfg_ahb' was expected ... sm8250-hdk.dtb: phy@88e9000: clocks: [[46, 185], [44, 0], [46, 187]] is too short sm8250-hdk.dtb: phy@88e9000: clock-names:1: 'cfg_ahb' was expected Signed-off-by:
Rob Herring <robh@kernel.org> Link: https://lore.kernel.org/r/20221225115944.55425-2-krzysztof.kozlowski@linaro.orgSigned-off-by:
-
Krzysztof Kozlowski authored
USB3 DP PHY on SC7280 is used with SM8250 fallback: sc7280-herobrine-evoker.dtb: phy-wrapper@88e9000: compatible: ['qcom,sc7280-qmp-usb3-dp-phy', 'qcom,sm8250-qmp-usb3-dp-phy'] is too long Signed-off-by:
-
Krzysztof Kozlowski authored
It is more readable to define properties in top-level "properties:" and restrict them (if needed) per compatible in the "if" block. Defining properties in "if" block does not work correctly with additionalProperties:false: sc7180-trogdor-pazquel-lte-ti.dtb: phy@88e3000: 'qcom,bias-ctrl-value', 'qcom,charge-ctrl-value', 'qcom,hsdisc-trim-value', 'qcom,imp-res-offset-value', 'qcom,preemphasis-level', 'qcom,preemphasis-width' do not match any of the regexes: 'pinctrl-[0-9]+' Signed-off-by: -
Krzysztof Kozlowski authored
Document SoC-specific compatibles with generic fallback (e.g. qcom,usb-snps-hs-7nm-phy) already used in DTSI. Add SoC-specific compatibles for PHY on SDX55 and SDX65. This disallows usage of the qcom,usb-snps-hs-5nm-phy and qcom,usb-snps-hs-7nm-phy generic compatibles alone. Do not touch remaining two compatibles - qcom,usb-snps-femto-v2-phy and qcom,sc8180x-usb-hs-phy - because there are no upstream users, so not sure what was the intention for them. This fixes warnings like: sa8295p-adp.dtb: phy@88e5000: compatible: 'oneOf' conditional failed, one must be fixed: ['qcom,sc8280xp-usb-hs-phy', 'qcom,usb-snps-hs-5nm-phy'] is too long 'qcom,sc8280xp-usb-hs-phy' is not one of ['qcom,sm8150-usb-hs-phy', 'qcom,sm8250-usb-hs-phy', 'qcom,sm8350-usb-hs-phy', 'qcom,sm8450-usb-hs-phy'] 'qcom,usb-snps-hs-7nm-phy' was expected Signed-off-by: -
Yoshihiro Shimoda authored
Remove retry code in r8a779f0_eth_serdes_init() because r8a779f0_eth_serdes_chan_setting() was fixed so that no timeout happened in the initializing procedure. Signed-off-by:
Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com> Link: https://lore.kernel.org/r/20221226065316.3895480-3-yoshihiro.shimoda.uh@renesas.comSigned-off-by:
-
Yoshihiro Shimoda authored
Add r8a779f0_eth_serdes_power_on() to initialize the hardware for each channel from the step 9 or later on the datasheet. In other words, the procedure from the step 1 to 8 is for all channel and it is needed once only. So, the .init() in any channel instance is called, this driver initializes the hardware from step 1 to 8. And then, .power_on() is called, this driver initializes the hardware from step 9 or later. Signed-off-by:
-
Krzysztof Kozlowski authored
Convert Qualcomm USB HSIC PHY bindings to DT schema. Signed-off-by:
-
Haotien Hsu authored
Support role-switch-default-mode property when usb-role-switch is enabled. Signed-off-by:
Haotien Hsu <haotienh@nvidia.com> Link: https://lore.kernel.org/r/20221216042146.99307-1-haotienh@nvidia.comSigned-off-by:
-
Bhupesh Sharma authored
Enable SM6115 / SM4250 USB3 PHY support by adding the qmp_phy_cfg data. Since this PHY is the same as the one used on QCM2290, reuse the QCM2290 qmp_phy_cfg data already available. Signed-off-by:
Bhupesh Sharma <bhupesh.sharma@linaro.org> Link: https://lore.kernel.org/r/20221213122843.454845-4-bhupesh.sharma@linaro.orgSigned-off-by:
-
Bhupesh Sharma authored
As per the Qualcomm QMP v3 PHY programming guide document, QSERDES_V3_RX_UCDR_PI_CONTROLS configuration should be set to an initial configuration value of 0x80. Fix the same. Signed-off-by:
-
Bhupesh Sharma authored
Add dt-bindings for USB3 PHY found on Qualcomm SM6115 / SM4250 SoC. Signed-off-by:
-
- 12 Jan, 2023 17 commits
-
-
Frank Wunderlich authored
Add compatible string for mt7986. Signed-off-by:
Frank Wunderlich <frank-w@public-files.de> Acked-by:
Chunfeng Yun <chunfeng.yun@mediatek.com> Reviewed-by:
AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com> Reviewed-by:
Matthias Brugger <matthias.bgg@gmail.com> Link: https://lore.kernel.org/r/20230106152845.88717-2-linux@fw-web.deSigned-off-by:
-
Andre Przywara authored
So far we were assigning some crude "type" (SoC name, really) to each Allwinner USB PHY model, then guarding certain quirks based on this. This does not only look weird, but gets more or more cumbersome to maintain. Remove the bogus type names altogether, instead introduce flags for each quirk, and explicitly check for them. This improves readability, and simplifies future extensions. Signed-off-by:
Andre Przywara <andre.przywara@arm.com> Reviewed-by:
Jernej Skrabec <jernej.skrabec@gmail.com> Link: https://lore.kernel.org/r/20230109012223.4079299-4-andre.przywara@arm.comSigned-off-by:
-
Icenowy Zheng authored
The F1C100s SoC has one USB OTG port connected to a MUSB controller. Add support for its USB PHY. Signed-off-by:
Icenowy Zheng <uwu@icenowy.me> Acked-by:
-
Icenowy Zheng authored
Allwinner F1C100s has the most simple USB PHY among all Allwinner SoCs, because it has only one OTG USB controller, no host-only OHCI/EHCI controllers. Add a binding document for it. Following the current situation of one YAML file per SoC, this one is based on allwinner,sun8i-v3s-usb-phy.yaml, but with OHCI/EHCI-related bits removed. (The same driver in Linux, phy-sun4i-usb, covers all these binding files now.) Signed-off-by:
Samuel Holland <samuel@sholland.org> Signed-off-by:
-
Sing-Han Chen authored
Add support for the XUSB pad controller found on Tegra234 SoCs. It is mostly similar to the same IP found on Tegra194, because most of the Tegra234 XUSB PADCTL registers definition and programming sequence are the same as Tegra194, Tegra234 XUSB PADCTL can share the same driver with Tegra186 and Tegra194 XUSB PADCTL. Introduce a new feature, USB2 HW tracking, for Tegra234. The feature is to enable HW periodical PAD tracking which measure and capture the electric parameters of USB2.0 PAD. Signed-off-by:
Sing-Han Chen <singhanc@nvidia.com> Co-developed-by:
Wayne Chang <waynec@nvidia.com> Signed-off-by:
Jon Hunter <jonathanh@nvidia.com> Link: https://lore.kernel.org/r/20230111110450.24617-6-jonathanh@nvidia.comSigned-off-by:
-
Wayne Chang authored
Pad tracking is a one-time calibration for Tegra186 and Tegra194. Clk should be disabled after calibration. Disable clk after calibration. While at it add 100us delay for HW recording the calibration value. Signed-off-by:
-
Dmitry Baryshkov authored
Remove QMP PHY type-specific headers inclusion from the common header and move them to the specific PHY drivers to cleanup the namespaces used by different drivers. Signed-off-by:
-
Dmitry Baryshkov authored
Drop qcm2290_usb3phy_regs_layout, it is a duplicate of qmp_v3_usb3phy_regs_layout. Introduce qmp_v5_usb3phy_regs_layout to be used for sm8350 and sc8280xp. Signed-off-by:
-
Dmitry Baryshkov authored
Use symbolic names for the values inside reg layout arrays. New register names are added following the PCS register layout that is used by the particular PHY. Note: ipq8074 tables appear to use a mixture of v2 and v3 registers. This might need additional fixes. Signed-off-by:
-
Dmitry Baryshkov authored
The QPHY_PCS_MISC_TYPEC_CTRL register is not used, remove it from register layout. Signed-off-by:
-
Dmitry Baryshkov authored
The QPHY_PCS_LFPS_RXTERM_IRQ_STATUS register is not used, remove it from register layout. Signed-off-by:
-
Dmitry Baryshkov authored
Rename regs layouts to follow the QMP PHY version. Signed-off-by:
-
Dmitry Baryshkov authored
Use symbolic names for the values inside reg layout arrays. New register names are added following the PCS register layout that is used by the particular PHY. Signed-off-by:
-
Dmitry Baryshkov authored
Follow other QMP headers, split and rename UFS-specific PCS registers to ease comparing regs differences. Signed-off-by:
-
Dmitry Baryshkov authored
Use symbolic names for the values inside reg layout arrays. New register names are added following the PCS register layout that is used by the particular PHY. Note: ipq8074 tables appear to use a mixture of v2 and v3 registers. This might need additional fixes. Signed-off-by:
-
Dmitry Baryshkov authored
Rename regs layouts to follow the QMP PHY version. Signed-off-by:
-
Dmitry Baryshkov authored
Use symbolic names for the values inside reg layout arrays. Signed-off-by:
-
