This device is sold as 'Lenovo OneLink Pro Dock'.
Chipset is RTL8153 and works with r8152.
Signed-off-by: Vasily Titskiy <qehgt0@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The same hardware issue the at91 must work around applies to at least the
Zynq ethernet, and possibly more devices.  The driver also needs to handle
the RXUBR interrupt since it turns it on with MACB_RX_INT_FLAGS anyway.
Signed-off-by: Nathan Sullivan <nathan.sullivan@ni.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Sowmini Varadhan says:

====================
net/rds: RDS-TCP robustness fixes

This patch-set contains bug fixes for state-recovery at the RDS
layer when the underlying transport is TCP and the TCP state at one
of the endpoints is reset

V2 changes: DaveM comments to reduce memory footprint, follow
            NFS/RPC model where possible. Added test-case #3

Without the changes in this set, when one of the endpoints is reset,
the existing code does not correctly clean up RDS socket state for stale
connections, resulting in some unstable, timing-dependant behavior on
the wire, including an infinite exchange of 3WHs back-and-forth, and a
resulting potential to never converge RDS state.

Test cases used to verify the changes in this set are:

1. Start rds client/server applications on two participating nodes,
   node1 and node2. After at least one packet has been sent (to establish
   the TCP connection), restart the rds_tcp module on the client, and
   now resend packets. Tcpdump should show server sending a FIN for the
   "old" client port, and clean connection establishment/exchange for
   the new client port.

2. At the end of step 1, restart rds srever on node2, and start client on
   node1, make sure using tcpdump, 'netstat -an|grep 16385' that
   packets flow correctly.

3. start RDS client/server application on two participating nodes, and
   repeat steps 1 and 2, but this time, simulate node failure by doing
   "ifconfig <intf> down", so no FIN is sent.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

When the peer of an RDS-TCP connection restarts, a reconnect
attempt should only be made from the active side  of the TCP
connection, i.e. the side that has a transient TCP port
number. Do not add the passive side of the TCP connection
to the c_hash_node and thus avoid triggering rds_queue_reconnect()
for passive rds connections.
Signed-off-by: Sowmini Varadhan <sowmini.varadhan@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When running RDS over TCP, the active (client) side connects to the
listening ("passive") side at the RDS_TCP_PORT.  After the connection
is established, if the client side reboots (potentially without even
sending a FIN) the server still has a TCP socket in the esablished
state.  If the server-side now gets a new SYN comes from the client
with a different client port, TCP will create a new socket-pair, but
the RDS layer will incorrectly pull up the old rds_connection (which
is still associated with the stale t_sock and RDS socket state).

This patch corrects this behavior by having rds_tcp_accept_one()
always create a new connection for an incoming TCP SYN.
The rds and tcp state associated with the old socket-pair is cleaned
up via the rds_tcp_state_change() callback which would typically be
invoked in most cases when the client-TCP sends a FIN on TCP restart,
triggering a transition to CLOSE_WAIT state. In the rarer event of client
death without a FIN, TCP_KEEPALIVE probes on the socket will detect
the stale socket, and the TCP transition to CLOSE state will trigger
the RDS state cleanup.
Signed-off-by: Sowmini Varadhan <sowmini.varadhan@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

If there are only IPv6 source specific default routes present, the
host gets -ENETUNREACH on e.g. connect() because ip6_dst_lookup_tail
calls ip6_route_output first, and given source address any, it fails,
and ip6_route_get_saddr is never called.

The change is to use the ip6_route_get_saddr, even if the initial
ip6_route_output fails, and then doing ip6_route_output _again_ after
we have appropriate source address available.

Note that this is '99% fix' to the problem; a correct fix would be to
do route lookups only within addrconf.c when picking a source address,
and never call ip6_route_output before source address has been
populated.
Signed-off-by: Markus Stenberg <markus.stenberg@iki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>

Johan Hedberg says:

====================
Here are a couple of important Bluetooth & mac802154 fixes for 4.1:

 - mac802154 fix for crypto algorithm allocation failure checking
 - mac802154 wpan phy leak fix for error code path
 - Fix for not calling Bluetooth shutdown() if interface is not up

Let me know if there are any issues pulling. Thanks.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

I forgot to update tcp_westwood when changing get_info() behavior,
this patch should fix this.

Fixes: 64f40ff5 ("tcp: prepare CC get_info() access from getsockopt()")
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge tag 'wireless-drivers-for-davem-2015-05-05' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers

Kalle Valo says:

====================
iwlwifi:

* fix firmware API for -13.ucode
* fix RSSI handling that avoid bad roaming decision
* fix firmware debug
* fix MFUART operation
* fix ASSERT while restart the hardware (because of another ASSERT e.g)

ath9k:

* fix per-packet tx power configuration

rtlwifi:

* rtl8192cu: Fix kernel deadlock
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Move to include/uapi/linux/mpls.h to be externally visibile.
Signed-off-by: Tom Herbert <tom@herbertland.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Or Gerlitz says:

====================
mlx4 fixes for 4.1-rc2

Eran's fix is for a small off-by-one introduces on 4.1-rc1.

Yisahi fixes an issue with comes into play only on VMs with
many (> 256) vCPUs.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

The Firmware uses dynamic EQs allocation based on number of VFs and
max EQs that can be allocated. As a result, VF can have EQ numbers
that are larger than 256.

According to the firmware spec, the max value is limited to be 1024
(10 bits), adapt the relevant code accordingly. This bug was impossible
to hit prior to commit 7ae0e400 ("net/mlx4_core: Flexible (asymmetric)
allocation of EQs and MSI-X vectors for PF/VFs") which actually enables
large number of EQs for VFs.
Signed-off-by: Yishai Hadas <yishaih@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This caused the en_stats_adder helper to accumulate a field which is
not related to the counter, fix that.

Fixes: a3333b35 ('net/mlx4_en: Moderate ethtool callback to show [..]')
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

With commit b56fc3c5 ("hv_netvsc: Fix a bug in netvsc_start_xmit()"),
skb variable is no longer used in netvsc_send. Remove variable and dead
code that depended on it.

Cc: Haiyang Zhang <haiyangz@microsoft.com>
Cc: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: Jerry Snitselaar <jsnitsel@redhat.com>
Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge tag 'mac80211-for-davem-2015-05-04' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211

Johannes Berg says:

====================
We have only a few fixes right now:
 * a fix for an issue with hash collision handling in the
   rhashtable conversion
 * a merge issue - rhashtable removed default shrinking
   just before mac80211 was converted, so enable it now
 * remove an invalid WARN that can trigger with legitimate
   userspace behaviour
 * add a struct member missing from kernel-doc that caused
   a lot of warnings
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Submit 909d9faa ("bnx2x: Prevent inner-reload while VFs exist")
contained a bug - MTU change was not prevented by it; Instead, it
`randomally' prevented bnx2x_resume() from running [harmless yet wrong].

This moves the check to its correct spot.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge branch 'for-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/bluetooth/bluetooth-next

Johan Hedberg says:

====================
pull request: bluetooth-next 2015-05-04

Here's the first bluetooth-next pull request for 4.2:

 - Various fixes for at86rf230 driver
 - ieee802154: trace events support for rdev->ops
 - HCI UART driver refactoring
 - New Realtek IDs added to btusb driver
 - Off-by-one fix for rtl8723b in btusb driver
 - Refactoring of btbcm driver for both UART & USB use

Please let me know if there are any issues pulling. Thanks.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

c0adf54a introduced new sparse warnings:
  CHECK   /home/dahern/kernels/linux.git/net/rds/ib_cm.c
net/rds/ib_cm.c:191:34: warning: incorrect type in initializer (different base types)
net/rds/ib_cm.c:191:34:    expected unsigned long long [unsigned] [usertype] dp_ack_seq
net/rds/ib_cm.c:191:34:    got restricted __be64 <noident>
net/rds/ib_cm.c:194:51: warning: cast to restricted __be64

The temporary variable for sequence number should have been declared as __be64
rather than u64. Make it so.
Signed-off-by: David Ahern <david.ahern@oracle.com>
Cc: shamir rabinovitch <shamir.rabinovitch@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This reverts commit 8d7d9cca.

Now that the necessary infrastructure is really all there
in the tree, we can put this change back in.
Signed-off-by: David S. Miller <davem@davemloft.net>

When smsc911x uses GPIO as the interrupt controller, and if both are
loaded as modules, we get following error:

"smsc911x: Could not allocate irq resource"

This issue is because of smsc911x using platform_get_resource to get
device tree based irq resource.

commit "9ec36caf (of/irq: do irq resolution in platform_get_irq)" and
commit "7085a7 (drivers: platform: parse IRQ flags from resources)" add
support in platform_get_irq to resolve irq and irq_flags respectively
for both modern device tree and legacy static platform data platforms.

Modify smsc911x driver to use platform_get_irq to pick up irq resource
correctly and use irq_get_trigger_type to get the IRQ trigger flags.
Signed-off-by: Kamlakant Patel <kamlakant.patel@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The code in __netdev_upper_dev_link() has an over-stringent
loop detection logic that actually prevents valid configurations
from working correctly.

In particular, the logic returns an error if an upper device
is already in the list of all upper devices for a given dev.
This particular check seems to be a overzealous as it disallows
perfectly valid configurations.  For example:
  # ip l a link eth0 name eth0.10 type vlan id 10
  # ip l a dev br0 typ bridge
  # ip l s eth0.10 master br0
  # ip l s eth0 master br0  <--- Will fail

If you switch the last two commands (add eth0 first), then both
will succeed.  If after that, you remove eth0 and try to re-add
it, it will fail!

It appears to be enough to simply check adj_list to keeps things
safe.

I've tried stacking multiple devices multiple times in all different
combinations, and either rx_handler registration prevented the stacking
of the device linking cought the error.
Signed-off-by: Vladislav Yasevich <vyasevic@redhat.com>
Acked-by: Jiri Pirko <jiri@resnulli.us>
Acked-by: Veaceslav Falico <vfalico@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

As German phone operators are discontinuing ISDN service, neither
Hansjörg nor I will be able to maintain the Gigaset ISDN drivers
any longer. Paul Bolle offered to step into the breach for odd
fixes.
Signed-off-by: Tilman Schmidt <tilman@imap.cc>
Acked-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: David S. Miller <davem@davemloft.net>

Eliminate 90 of these warnings:

Warning(..//include/net/mac80211.h:1682): No description found for parameter 'drv_priv[0]'
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

When a macvlan device is placed in promiscuous mode, it currently
just sets it's multicast mask to permissive, but doesn't change
the state of the lower device.  As a result, not all multicast
traffic can be received on such device.  Additionally, none of
a vlan traffic can be received on such device as well.
This patch propagates the promiscuous mode setting to lower device
so that lower device may receive all packets that macvlan may
be interested in.
Signed-off-by: Vladislav Yasevich <vyasevic@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This reverts commit c243d7e2.

That patch is solving a non-existant problem while creating a
real problem.  Just because a socket is allocated in the init
name space doesn't mean that it gets hashed in the init name space.

When we unhash it the name space must be the same as the one
we had when we hashed it.  So this patch is completely bogus
and causes socket leaks.
Reported-by: Andrey Wagin <avagin@gmail.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>

Alexander Duyck says:

====================
Clean-up some bits related to netpoll

This patch set cleans up some minor items related to netpoll.  The first
patch addresses an Rx clean-up bug that is triggered due to an assumption
that napi->poll wouldn't be called with a budget of 0.  The other two
patches address dev_kfree_skb being called in the xmit path which isn't
valid since netpoll will call ndo_start_xmit with IRQs disabled.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

With netpoll making use of the transmit function it is possible for the
ndo_start_xmit function to be called with irqs disabled.  As such we need
to use dev_kfree_skb_any in the Tx cleanup path for frames that are
dropped.
Signed-off-by: Alexander Duyck <alexander.h.duyck@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The function r8169_csum_workaround is called in the ndo_start_xmit path of
the r8169 driver.  As such it should not be using dev_kfree_skb as it is
not irq safe, so instead we should be using dev_kfree_skb_any for freeing
in the dropped path, and dev_consume_skb_any for any frames that were
transmitted.
Signed-off-by: Alexander Duyck <alexander.h.duyck@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The netpoll path will call napi->poll with a budget of 0 in order to clean
the Tx rings only.  This change updates the fm10k driver so that it will
correctly support that instead of cleaning 1 Rx frame if a budget of 0 is
received.
Signed-off-by: Alexander Duyck <alexander.h.duyck@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add the missing unregister for the mv88e6352_switch_driver.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge tag 'linux-can-fixes-for-4.1-20150501' of git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can

Marc Kleine-Budde says:

====================
this is a pull request of a single patch for net/master.

The patch is contributed by Jeppe Ledet-Pedersen, it fixes the
extended frame handling in the xilinx driver.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

This file is built off of a tristate Kconfig option and also contains
modular function calls so it should explicitly include module.h to
avoid compile breakage during header shuffles done in the future.

Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: netdev@vger.kernel.org
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

rdma_conn_param private data is copied using memcpy after headers such
as cma_hdr (see cma_resolve_ib_udp as example). so the start of the
private data is aligned to the end of the structure that come before. if
this structure end with u32 the meaning is that the start of the private
data will be 4 bytes aligned. structures that use u8/u16/u32/u64 are
naturally aligned but in case the structure start is not 8 bytes aligned,
all u64 members of this structure will not be aligned. to solve this issue
we must use special macros that allow unaligned access to those
unaligned members.

Addresses the following kernel log seen when attempting to use RDMA:

Kernel unaligned access at TPC[10507a88] rds_ib_cm_connect_complete+0x1bc/0x1e0 [rds_rdma]
Acked-by: Chien Yen <chien.yen@oracle.com>
Signed-off-by: shamir rabinovitch <shamir.rabinovitch@oracle.com>
[Minor tweaks for top of tree by:]
Signed-off-by: David Ahern <david.ahern@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

We currently limit the hash table size to 64K which is very bad
as even 10 years ago it was relatively easy to generate millions
of sockets.

Since the hash table is naturally limited by memory allocation
failure, we don't really need an explicit limit so this patch
removes it.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Acked-by: Thomas Graf <tgraf@noironetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Under presence of TSO/GSO/GRO packets, codel at low rates can be quite
useless. In following example, not a single packet was ever dropped,
while average delay in codel queue is ~100 ms !

qdisc codel 0: parent 1:12 limit 16000p target 5.0ms interval 100.0ms
 Sent 134376498 bytes 88797 pkt (dropped 0, overlimits 0 requeues 0)
 backlog 13626b 3p requeues 0
  count 0 lastcount 0 ldelay 96.9ms drop_next 0us
  maxpacket 9084 ecn_mark 0 drop_overlimit 0

This comes from a confusion of what should be the minimal backlog. It is
pretty clear it is not 64KB or whatever max GSO packet ever reached the
qdisc.

codel intent was to use MTU of the device.

After the fix, we finally drop some packets, and rtt/cwnd of my single
TCP flow are meeting our expectations.

qdisc codel 0: parent 1:12 limit 16000p target 5.0ms interval 100.0ms
 Sent 102798497 bytes 67912 pkt (dropped 1365, overlimits 0 requeues 0)
 backlog 6056b 3p requeues 0
  count 1 lastcount 1 ldelay 36.3ms drop_next 0us
  maxpacket 10598 ecn_mark 0 drop_overlimit 0
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Kathleen Nichols <nichols@pollere.com>
Cc: Dave Taht <dave.taht@gmail.com>
Cc: Van Jacobson <vanj@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Do not use ieee80211_vif pointer in ath_get_rate_txpower() since it has been
overwritten by setup_frame_info() and it will result in a corrupted tx power
configuration. Set per-packet tx power in setup_frame_info() according to
current vif tx power.
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi83@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

Merge tag 'iwlwifi-for-kalle-2015-04-28' of https://git.kernel.org/pub/scm/linux/kernel/git/iwlwifi/iwlwifi-fixes

* fix firmware API for -13.ucode
* fix RSSI handling that avoid bad roaming decision
* fix firmware debug
* fix MFUART operation
* fix ASSERT while restart the hardware (because of another ASSERT e.g)

Pull networking fixes from David Miller:

 1) Receive packet length needs to be adjust by 2 on RX to accomodate
    the two padding bytes in altera_tse driver.  From Vlastimil Setka.

 2) If rx frame is dropped due to out of memory in macb driver, we leave
    the receive ring descriptors in an undefined state.  From Punnaiah
    Choudary Kalluri

 3) Some netlink subsystems erroneously signal NLM_F_MULTI.  That is
    only for dumps.  Fix from Nicolas Dichtel.

 4) Fix mis-use of raw rt->rt_pmtu value in ipv4, one must always go via
    the ipv4_mtu() helper.  From Herbert Xu.

 5) Fix null deref in bridge netfilter, and miscalculated lengths in
    jump/goto nf_tables verdicts.  From Florian Westphal.

 6) Unhash ping sockets properly.

 7) Software implementation of BPF divide did 64/32 rather than 64/64
    bit divide.  The JITs got it right.  Fix from Alexei Starovoitov.

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (30 commits)
  ipv4: Missing sk_nulls_node_init() in ping_unhash().
  net: fec: Fix RGMII-ID mode
  net/mlx4_en: Schedule napi when RX buffers allocation fails
  netxen_nic: use spin_[un]lock_bh around tx_clean_lock
  net/mlx4_core: Fix unaligned accesses
  mlx4_en: Use correct loop cursor in error path.
  cxgb4: Fix MC1 memory offset calculation
  bnx2x: Delay during kdump load
  net: Fix Kernel Panic in bonding driver debugfs file: rlb_hash_table
  net: dsa: Fix scope of eeprom-length property
  net: macb: Fix race condition in driver when Rx frame is dropped
  hv_netvsc: Fix a bug in netvsc_start_xmit()
  altera_tse: Correct rx packet length
  mlx4: Fix tx ring affinity_mask creation
  tipc: fix problem with parallel link synchronization mechanism
  tipc: remove wrong use of NLM_F_MULTI
  bridge/nl: remove wrong use of NLM_F_MULTI
  bridge/mdb: remove wrong use of NLM_F_MULTI
  net: sched: act_connmark: don't zap skb->nfct
  trivial: net: systemport: bcmsysport.h: fix 0x0x prefix
  ...

Here the "other side" refers to the guest or host.
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

With my job change kernel work will be "own time"; I'm keeping lguest
and modules (and the virtio standards work), but virtio kernel has to
go.

This makes it clear that Michael is in charge.  He's good, but having
me watch over his shoulder won't help.

Good luck Michael!
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>