The PMIC and EEPROM can operate at 400kHz, so use this speed.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

For R-Car V3H hook up SYS-DMAC1 and SYS-DMAC2 to IPMMU-DS1 to match
information in the R-Car Gen3 Rev.1.00 (April 2018) datasheet.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

For R-Car E3 hook up SYS-DMAC0, SYS-DMAC1 and SYS-DMAC2 to
IPMMU-DS0 and IPMMU-DS1 in same way as for R-Car H3.
This follows the R-Car Gen3 Rev.1.00 (April 2018) datasheet.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Add HDMI and CVBS inputs device nodes to R-Car E3 Ebisu board.

Both HDMI and CVBS inputs are connected to an ADV7482 video decoder hooked to
the SoC CSI-2 receiver port.
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

The thermal device is supposed to be always enabled.  As the default
value of the status property is "okay", there is no need to make this
explicit in SoC-specific .dtsi files where no override is involved.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

The r8a77965 has a single FDP1 instance.
Signed-off-by: Hoan Nguyen An <na-hoan@jinso.co.jp>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

- Device nodes with unit addresses are sorted by unit address,
  - Device nodes without unit addresses and references are sorted
    alphabetically.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Successfully tested on H3 ES1.0 and ES2.0, M3-W ES1.0, and M3-N ES1.0.
Even previously stubborn cards work fine. Transfer rates were >60MB/s.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

This patch adds SYS-DMAC{0,1,2} device nodes for the R8A77990 SoC.
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
Signed-off-by: Yoshihiro Kaneko <ykaneko0929@gmail.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Add device nodes for I2C ch[0-7] to R-Car E3 R8A77990 device tree.
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Tested-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Add device nodes for VIN4, VIN5 and CSI40 to R-Car E3 R8A77990 device tree.
Signed-off-by: Koji Matsuoka <koji.matsuoka.xm@renesas.com>
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Tested-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
[simon: sorted nodes by bus address, then IP block]
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Add the device nodes for all MSIOF SPI controllers, incl. clocks, power
domains, and resets properties.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

To preserve by-address-per-group sort order.

Fixes: 0f6d237c ("arm64: dts: renesas: r8a7795: add ccree to device tree")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Add the device node for the external SCIF_CLK, and describe the clock
inputs for the Baud Rate Generator for External Clock (BRG) for SCIF2,
which can increase serial clock accuracy.

The presence of the SCIF_CLK crystal and its clock frequency depend on
the actual board.
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
[geert: Enhance patch description]
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Use the SoC-specific CPG/MSSR include file to allow future use of
R8A77990_CLK_* symbols.
Replace the hardcoded power domain indices by R8A77990_PD_* symbols.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

The comments describing the non-default switch settings to use SATA are
confusing: 'Off' refers to the switch position, not to the MD12 logic
value, while the parentheses suggest otherwise.  Rephrase to fix this.

Fixes: bec000784d5bb571 ("arm64: dts: renesas: salvator-xs: enable SATA")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

usb2_phy1 accidentally uses the same clock/reset as usb2_phy0.

Fixes: b5857630 ("arm64: dts: renesas: r8a77965: add usb2_phy nodes")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Should be "renesas,usbhs-r8a77965", not "renesas,usbhs-r8a7796".

Fixes: a06e8af8 ("arm64: dts: renesas: r8a77965: add HS-USB node")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

To preserve alphabetical sort order.

Fixes: 4c529600 ("arm64: dts: renesas: r8a77965: Add R-Car Gen3 thermal support")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

To preserve alphabetical sort order.

Fixes: 4edac426aff11a37 ("arm64: dts: renesas: condor/v3hsk: add DU/LVDS/HDMI support")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
[simon: updated for a few new cases]
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

This is based on the existing KF device tree sources:
$ ls -1 arch/arm64/boot/dts/renesas/*-kf.dts
arch/arm64/boot/dts/renesas/r8a7795-es1-h3ulcb-kf.dts
arch/arm64/boot/dts/renesas/r8a7795-h3ulcb-kf.dts
arch/arm64/boot/dts/renesas/r8a7796-m3ulcb-kf.dts
Signed-off-by: Eugeniu Rosca <erosca@de.adit-jv.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Enable PCIe PHY and PCIEC and specify the PCIe bus clock for the Condor
board.

Based on the original (and large) patch by Vladimir Barinov.
Signed-off-by: Vladimir Barinov <vladimir.barinov@cogentembedded.com>
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Describe the PCIe PHY, PCIEC, and PCIe bus clock in the R8A77980 device
tree.

Based on the original (and large) patch by Vladimir Barinov.
Signed-off-by: Vladimir Barinov <vladimir.barinov@cogentembedded.com>
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Add usb3.0 phy, host and function device nodes on RZ/G2M SoC dtsi.
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Add usb dmac and hsusb device nodes on RZ/G2M SoC dtsi.
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Add USB2.0 phy and host (EHCI/OHCI) device nodes on RZ/G2M SoC dtsi.
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Add FCPF and FCPV instances to the r8a774a1 dtsi, similarly
to what was done for the r8a7796 with commit 41dbbf0c
("arm64: dts: r8a7796: Add FCPF and FCPV instances"),
commit 69490bc9 ("arm64: dts: renesas: r8a7796: Point
FDP1 via FCPF to IPMMU-VI0"), and commit cef942d0 ("arm64:
dts: renesas: r8a7796: Point VSPI via FCPVI to IPMMU-VC0").
Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Reviewed-by: Biju Das <biju.das@bp.renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Add sound support for the RZ/G2M SoC (a.k.a. R8A774A1).

This work is based on similar work done on the R8A7796 SoC
by Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>.
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

This patch adds PWM[0123456] device nodes to the RZ/G2M (a.k.a R8A774A1)
device tree.
Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Reviewed-by: Biju Das <biju.das@bp.renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

This patch adds definitions for L2 cache for the Cortex-A53 CPU
cores (512 KiB in size, organized as 32 KiB x 16 ways), adds
Cortex-A53 CPU cores (setting a total of 6 cores, 2 x Cortex-A57
+ 4 x Cortex-A53), and finally enables the performance monitor
unit for the Cortex-A53 cores on the R8A774A1 SoC.

Based on work done for r8a7796 SoC.
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Add the device nodes for all MSIOF SPI controllers on RZ/G2M SoC.

Based on several similar patches of the R8A7796 device tree
by Geert Uytterhoeven <geert+renesas@glider.be>
and Simon Horman <horms+renesas@verge.net.au>.
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Add r8a774a1 IPMMU nodes.
Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Reviewed-by: Biju Das <biju.das@bp.renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Add thermal support for R8A774A1 (RZ/G2M) SoC.

Based on the work done for r8a7796 SoC.
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Add the I2C[0-6] and IIC Bus Interface for DVFS (IIC for DVFS)
devices nodes to the r8a774a1 device tree.
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Add SDHI nodes to the DT of the r8a774a1 SoC.
Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Reviewed-by: Biju Das <biju.das@bp.renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Add GPIO device nodes to the DT of the r8a774a1 SoC.
Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Reviewed-by: Biju Das <biju.das@bp.renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

This patch adds pinctrl device node for R8A774A1 SoC.
Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Reviewed-by: Biju Das <biju.das@bp.renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Add a device node for the Watchdog Timer (RWDT) controller on the Renesas
RZ/G2M (r8a774a1) SoC.
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

This patch adds the SoC specific part of the Ethernet AVB
device tree node.
Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Reviewed-by: Biju Das <biju.das@bp.renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>