- 07 Oct, 2014 1 commit
-
-
James Bottomley authored
-
- 01 Oct, 2014 19 commits
-
-
Christoph Hellwig authored
Add a Kconfig option to enable the blk-mq path for SCSI by default to ease testing and deployment in setups that know they benefit from blk-mq. Signed-off-by:
Christoph Hellwig <hch@lst.de> Reviewed-by:
Martin K. Petersen <martin.petersen@oracle.com> Reviewed-by:
Robert Elliott <elliott@hp.com> Tested-by:
-
Dolev Raviv authored
- Adding some of the definitions missing in unipro.h, including power enumeration. - Read Modify Write Line helper function - Indication for the type of suspend Signed-off-by:
Dolev Raviv <draviv@codeaurora.org> Signed-off-by:
Subhash Jadavani <subhashj@codeaurora.org> Signed-off-by:
Yaniv Gardi <ygardi@codeaurora.org> Signed-off-by:
-
Subhash Jadavani authored
Add capability to control the auto bkops during suspend. If host explicitly enables the auto bkops (background operation) on device then only device would perform the bkops on its own. If auto bkops is not enabled explicitly and if the device reaches to state where it must do background operation, device would raise the urgent bkops exception event to host and then host will enable the auto bkops on device. This patch adds the option to choose whether auto bkops should be enabled during runtime suspend or not. Since we don't want to keep the device active to perform the non critical bkops, host will enable urgent bkops only. Keep auto-bkops enabled after resume if urgent bkops needed. If device bkops status shows that its in critical need of executing background operations, host should allow the device to continue doing background operations. Signed-off-by:
-
Sahitya Tummala authored
The clocks for UFS device will be managed by generic DVFS (Dynamic Voltage and Frequency Scaling) framework within kernel. This devfreq framework works with different governors to scale the clocks. By default, UFS devices uses simple_ondemand governor which scales the clocks up if the load is more than upthreshold and scales down if the load is less than downthreshold. Signed-off-by:
Sahitya Tummala <stummala@codeaurora.org> Signed-off-by:
-
Sahitya Tummala authored
Add freq-table-hz propery for UFS device to keep track of <min max> frequencies supported by UFS clocks. Signed-off-by:
-
Sahitya Tummala authored
The UFS controller clocks can be gated after certain period of inactivity, which is typically less than runtime suspend timeout. In addition to clocks the link will also be put into Hibern8 mode to save more power. The clock gating can be turned on by enabling the capability UFSHCD_CAP_CLK_GATING. To enable entering into Hibern8 mode as part of clock gating, set the capability UFSHCD_CAP_HIBERN8_WITH_CLK_GATING. The tracing events for clock gating can be enabled through debugfs as: echo 1 > /sys/kernel/debug/tracing/events/ufs/ufshcd_clk_gating/enable cat /sys/kernel/debug/tracing/trace_pipe Signed-off-by:
-
Dolev Raviv authored
Sometimes, the device shall report its maximum power and speed capabilities, but we might not wish to configure it to use those maximum capabilities. This change adds support for the vendor specific host driver to implement power change notify callback. To enable configuring different power modes (number of lanes, gear number and fast/slow modes) it is necessary to split the configuration stage from the stage that reads the device max power mode. In addition, it is not required to read the configuration more than once, thus the configuration is stored after reading it once. Signed-off-by:
-
Subhash Jadavani authored
This patch adds support for UFS device and UniPro link power management during runtime/system PM. Main idea is to define multiple UFS low power levels based on UFS device and UFS link power states. This would allow any specific platform or pci driver to choose the best suited low power level during runtime and system suspend based on their power goals. bkops handlig: To put the UFS device in sleep state when bkops is disabled, first query the bkops status from the device and enable bkops on device only if device needs time to perform the bkops. START_STOP handling: Before sending START_STOP_UNIT to the device well-known logical unit (w-lun) to make sure that the device w-lun unit attention condition is cleared. Write protection: UFS device specification allows LUs to be write protected, either permanently or power on write protected. If any LU is power on write protected and if the card is power cycled (by powering off VCCQ and/or VCC rails), LU's write protect status would be lost. So this means those LUs can be written now. To ensures that UFS device is power cycled only if the power on protect is not set for any of the LUs, check if power on write protect is set and if device is in sleep/power-off state & link in inactive state (Hibern8 or OFF state). If none of the Logical Units on UFS device is power on write protected then all UFS device power rails (VCC, VCCQ & VCCQ2) can be turned off if UFS device is in power-off state and UFS link is in OFF state. But current implementation would disable all device power rails even if UFS link is not in OFF state. Low power mode: If UFS link is in OFF state then UFS host controller can be power collapsed to avoid leakage current from it. Note that if UFS host controller is power collapsed, full UFS reinitialization will be required on resume to re-establish the link between host and device. Signed-off-by:
Sujit Reddy Thumma <sthumma@codeaurora.org> Signed-off-by:
-
Subhash Jadavani authored
UFS device may have standard LUs and LUN id could be from 0x00 to 0x7F. UFS device specification use "Peripheral Device Addressing Format" (SCSI SAM-5) for standard LUs. UFS device may also have the Well Known LUs (also referred as W-LU) which again could be from 0x00 to 0x7F. For W-LUs, UFS device specification only allows the "Extended Addressing Format" (SCSI SAM-5) which means the W-LUNs would start from 0xC100 onwards. This means max. LUN number reported from UFS device could be 0xC17F hence this patch advertise the "max_lun" as 0xC17F which will allow SCSI mid layer to detect the W-LUs as well. But once the W-LUs are detected, UFSHCD driver may get the commands with SCSI LUN id upto 0xC17F but UPIU LUN id field is only 8-bit wide so it requires the mapping of SCSI LUN id to UPIU LUN id. This patch also add support for this mapping. Signed-off-by:
-
Subhash Jadavani authored
UFS device specification requires the UFS devices to support 4 well known logical units: "REPORT_LUNS" (address: 01h) "UFS Device" (address: 50h) "RPMB" (address: 44h) "BOOT" (address: 30h) UFS device's power management needs to be controlled by "POWER CONDITION" field of SSU (START STOP UNIT) command. But this "power condition" field will take effect only when its sent to "UFS device" well known logical unit hence we require the scsi_device instance to represent this logical unit in order for the UFS host driver to send the SSU command for power management. We also require the scsi_device instance for "RPMB" (Replay Protected Memory Block) LU so user space process can control this LU. User space may also want to have access to BOOT LU. This patch adds the scsi device instances for each of all well known LUs (except "REPORT LUNS" LU). Signed-off-by:
-
Yaniv Gardi authored
The maximum power consumption in active is determined by bActiveICCLevel. The configuration is done by reading max current supported by the regulators connected to VCC, VCCQ and VCCQ2 rails on the boards, and reading the current consumption levels from the device for each rails (vcc/vccq/vccq2) using power descriptor. We configure the bActiveICCLevel attribute, with the max value that correspond to the minimum-of(VCC-current-level,VCCQ-current-level, VCCQ2-current-level). In order to minimize resume latency, pre-fetch icc levels and reference clock during initialization and avoid reading them each link startup during resume. Signed-off-by:
Raviv Shvili <rshvili@codeaurora.org> Signed-off-by:
-
Sujit Reddy Thumma authored
In ->hce_enable_notify() callback the vendor specific initialization may carry out additional DME configuration using UIC commands and hence the UIC command completion interrupt enable bit should be set before the post reset notification. Add retries if the link-startup fails. This is required since due to hardware timing issues, the Uni-Pro link-startup might fail. The UFS HCI recovery procedure contradicts the Uni-Pro sequence. The UFS HCI specifies to resend DME_LINKSTARTUP command after IS.ULLS (link-lost interrupt) is received. The Uni-Pro specifies that if link-startup fails the link is in "down" state. The link-lost is indicated to the DME user only when the link is up. Hence, the UFS HCI recovery procedure of waiting for IS.ULLS and retrying link-startup may not work properly. At the end, if detection fails, power off (disable clocks, regulators, phy) if the UFS device detection fails. This saves power while UFS device is not embedded into the system. Signed-off-by:
-
Subhash Jadavani authored
Currently reading query descriptor is more tightened to each descriptor type. This patch generalize the approach and allows reading any parameter from any query descriptor. Signed-off-by:
-
Raviv Shvili authored
Add the support for voting of the regulator powering the host controller logic. Signed-off-by:
-
Sujit Reddy Thumma authored
Add generic clock initialization support for UFSHCD platform driver. The clock info is read from device tree using standard clock bindings. A generic max-clock-frequency-hz property is defined to save information on maximum operating clock frequency the h/w supports. Signed-off-by:
-
Sujit Reddy Thumma authored
UFS devices are powered by at most three external power supplies - - VCC - The flash memory core power supply, 2.7V to 3.6V or 1.70V to 1.95V - VCCQ - The controller and I/O power supply, 1.1V to 1.3V - VCCQ2 - Secondary controller and/or I/O power supply, 1.65V to 1.95V For some devices VCCQ or VCCQ2 are optional as they can be generated using internal LDO inside the UFS device. Add DT bindings for voltage regulators that can be controlled from host driver. Signed-off-by:
-
Sujit Reddy Thumma authored
Some vendor specific controller versions might need to configure vendor specific - registers, clocks, voltage regulators etc. to initialize the host controller UTP layer and Uni-Pro stack. Provide some common initialization operations that can be used to configure vendor specifics. The methods can be extended in future, for example, for power mode transitions. The operations are vendor/board specific and hence determined with the help of compatible property in device tree. Signed-off-by:
-
Subhash Jadavani authored
If LLD has added scsi device (by calling scsi_add_device) before scheduling async scsi_scan_host then scsi_finish_async_scan() will end up calling scsi_sysfs_add_sdev for scsi device which was already added by LLD. This patch fixes this issue by skipping the call to scsi_sysfs_add_sdev() if it's already visible to rest of the kernel. Signed-off-by:
Hannes Reinecke <hare@suse.de> Reviewed-by:
-
Subhash Jadavani authored
Some devices may respond with wrong type for well-known logical units. This patch forces well-known type for devices which doesn't report it correct. Signed-off-by:
-
- 30 Sep, 2014 8 commits
-
-
Sebastian Herbszt authored
Commit 1abf635d (scsi: use 64-bit value for 'max_luns') changed the order of Scsi_Host members. Update the comment to reflect this. Signed-off-by:
Sebastian Herbszt <herbszt@gmx.de> Reviewed-by:
Bart Van Assche <bvanassche@acm.org> Reviewed-by:
-
Douglas Gilbert authored
A deadlock has been reported when the completion of SCSI commands (simulated by a timer) was surprised by a module removal. This patch removes one half of the offending locks around timer deletions. This fix is applied both to stop_all_queued() which is were the deadlock was discovered and stop_queued_cmnd() which has very similar logic. This patch should be applied both to the lk 3.17 tree and Christoph's drivers-for-3.18 tree. Tested-and-reported-by:
Milan Broz <gmazyland@gmail.com> Signed-off-by:
Douglas Gilbert <dgilbert@interlog.com> Signed-off-by:
-
Mike Christie authored
Dan Carpenter found a issue where be2iscsi would copy the ip from userspace to the driver buffer before checking the len of the data being copied: http://marc.info/?l=linux-scsi&m=140982651504251&w=2 This patch just has us only copy what we the driver buffer can support. Cc: <stable@vger.kernel.org> Tested-by:
John Soni Jose <sony.john-n@emulex.com> Signed-off-by:
Mike Christie <michaelc@cs.wisc.edu> Signed-off-by:
-
Mike Christie authored
This just has iscsi_tcp support ISCSI_PARAM_LOCAL_PORT which exports the local port being used by the iscsi connection. Signed-off-by:
-
John Soni Jose authored
Bump the driver version Signed-off-by:
Jayamohan Kallickal <jayamohan.kallickal@emulex.com> Signed-off-by:
-
John Soni Jose authored
In the reboot/shutdown path, workqueue was destroyed after the adapter resource were freed. The task associated with workqueue was getting executed after resources were freed. This lead to kernel panic. Signed-off-by:
-
Andreea-Cristina Bernat authored
The uses of "rcu_assign_pointer()" are NULLing out the pointers. According to RCU_INIT_POINTER()'s block comment: "1. This use of RCU_INIT_POINTER() is NULLing out the pointer" it is better to use it instead of rcu_assign_pointer() because it has a smaller overhead. The following Coccinelle semantic patch was used: @@ @@ - rcu_assign_pointer + RCU_INIT_POINTER (..., NULL) Signed-off-by:
Andreea-Cristina Bernat <bernat.ada@gmail.com> Acked-by:
Vasu Dev <vasu.dev@intel.com> Signed-off-by:
-
Chris Leech authored
add support for 20 Gbit and 40 Gbit links Signed-off-by:
Chris Leech <cleech@redhat.com> Signed-off-by:
-
- 26 Sep, 2014 1 commit
-
-
Christoph Hellwig authored
Fix a typo in the IPR_IOASC_HW_CMD_FAILED declaration. Based on a patch from Wen Xiong <wenxiong@linux.vnet.ibm.com>. Signed-off-by:
-
- 25 Sep, 2014 11 commits
-
-
Himanshu Madhani authored
Signed-off-by:
Himanshu Madhani <himanshu.madhani@qlogic.com> Signed-off-by:
Saurav Kashyap <saurav.kashyap@qlogic.com> Signed-off-by:
-
Saurav Kashyap authored
Signed-off-by:
Giridhar Malavali <giridhar.malavali@qlogic.com> Signed-off-by:
-
Quinn Tran authored
Signed-off-by:
Quinn Tran <quinn.tran@qlogic.com> Signed-off-by:
-
Himanshu Madhani authored
Signed-off-by:
-
Quinn Tran authored
Through the qla target code, the qlt_send_term_exchange() routine is used in various different places to cleanup an exchange. For the case of IOCB request queue is full, the exchange is left unhandled/ dangling. Existing code does not have re-try logic to cleanup the exchange. This patch add retry logic to cleanup the exchange before letting new commands through. For the case of FW running out of exchanges, driver need to reply SAM_STAT_BUSY to the initiators. This patch add a pending queue for the busy reply in case IOCB queue is unable to handle the cmd. Cc: <stable@vger.kernel.org> Signed-off-by:
-
Saurav Kashyap authored
Signed-off-by:
-
Arun Easi authored
ABTS path takes path similar to regular task management, but reset_count was not initialized when allocating mcmd causing the response to get dropped in qlt_xmit_tm_rsp. Fix this by initializing reset_count correctly. Signed-off-by:
Arun Easi <arun.easi@qlogic.com> Signed-off-by:
-
Arun Easi authored
A chip reset can occur after driver submits command to the stack. Abort command processing if a chip reset has occurred or in progress when you get a follow up for a command. Signed-off-by:
-
Arun Easi authored
Signed-off-by:
-
Himanshu Madhani authored
tcm_qla2xxx_get_task_tag incorrectly assume command is qla_tgt_cmd. Add check to see if it's a scsi cmd or task mgmt command. Signed-off-by:
-
Saurav Kashyap authored
Signed-off-by:
-
